K8m neo-v mobo dont detect seagate sata hdd st3808110as

k8m neo-v mobo dont detect seagate sata hdd st3808110as 80gb
bios dont detect the sata hdd.
any help would be appreciated thanks.

so thats it.
thanks alot tiresmoke. i really appreciate it.
btw. does the seagate sata hdd have a different jumper from the ide hdd? because my seagate hdd dont have any jumpers. i tried using the ide jumper and it wont fit.

Similar Messages

MSI KM8 neo V motherboard supports 500 GB SATA HDD ???

Hello all,
I have MSI KM8 neo V motherboard. I have recently purchased 500 GB SATA HDD to upgrade from old 80 GB SATA HDD.
My motherboard doesn't detect new 500 GB SATA HDD. . my mother board has any limitations on SATA HDD capacity?
Please let me know the limitations of MSI KM8 neo V motherboard for SATA HDD limitations suchas 500 GB SATA HDD
Regards,
Rajender

You may want to update to the latest BIOS first.
Your drive is backwards compatible so it should work. Worst case, there may be a jumper on the drive to set it to 1.5gb/s.
Although a 500 has not been tested on this board, 250s have. http://www.msi.com/file/test_report/TR3_159.pdf If a 250 works, no reason a 500 shouldn't work, depending if there is a jumper setting.
Seagate/Maxtor has added a user-accessible jumper-switch, known as the Force 150, to enable the drive to be switched between 1.5 Gbit/s and 3 Gbit/s operation. Western Digital uses a jumper setting called OPT1 Enabled to force 1.5 Gbit/s data transfer speed (OPT1 is enabled by putting the jumper on pins 5 & 6). Samsung drives can be switched to 1.5 Gbit/s mode using software that may be downloaded from the manufacturer's website. Upgrading a Samsung drive in this manner requires the temporary use of a SATA-2 (SATA 3.0 Gbit/s) controller while programming the drive . You may want to check with HDD manufacturer to see what they suggest in terms of running the drive on a SATA 1,5Gb (150) port.

MSI P965 Neo problem - cannot detect third sata HDD

My third SATA 1TB (WD) HDD cant be detected when i tried installing it. :( Previously, theres only 2 HDD which im using (640GB + 1TB) and everything worked fine. I was planning to have a dual boot of win 7 64 and kubuntu on my rig thus explaining the purchase of the third drive. wanna back-up the stuffs from the 640GB, but as stated, the new drive cant be detected. please advise.
(btw, all of em are SATA 2)

Quote
this third drive is on sata as well.
Yeah, but which port exactly is it connected to?
Quote
, if i swap the cable from my other 1TB hdd (since the OS is in the 640GB), it can be detected
Perhaps the other cable is bad?

Msi k8m neo-v not detecting SATA HDD

hi,
i am using MSI K8M NEO-V motherboard,
i have read all the threads related to it, and detection of SATA hdd's with it.
i have tried everything except the bios update.
i'v set the jumper to 1.5Gbps
tried different drives but no go
any help would be appreciated,
my system configuration is:
-msi mobo k8m neo-v (ms-7032 ver1) (bios version 3.1)
-hitachi deskstar 80 gb pata-ide hdd,
-1gig sd dd ram
-windows xp professional os
and i am trying to get SAMSUNG 500 GIG HDD (model- HD503HI) to get detected to my mobo
(and yes this 500 gig hdd os ok, it is getting detected in other pc's)

Quote from: Stu on 07-August-10, 23:28:47
If its a SATA-II (3Gb/s) drive, it will probably never work on that board.
VIA VT8237 chipset has known incompatibility issues with SATA 3Gb/s drives, which cannot be fixed. Either try and get hold of a SATA 1.5Gb/s drive, or just use a PATA (IDE) drive instead.
yes bro it is a sata-II 3GB/S drive..
any other workaround??

2 beeps from K8M Neo-V

I just built a new computer. But I keep getting 2 short beeps. I looked on MSI web site it saids parity circuit failure.
I triple checked everything. To me, at least, they are connected fine.
Do I have to return it or is there something I can do to find the problem.
Everything below is brand new
AMD Athlon 64 3000+
K8M Neo-V
1GB Corsair DDR 400
GeForce 6600
ATX Case(cooler master.. something)
My old parts
Antec 350W
2 Maxtor IDE
1 Sony CD-rom
1 Dvd rom
Please help me T.T

Hiya,I posted this before.Mine also beeps two times.
AMI BIOS beep codes with two short beeps means parity error,but i dont think so
I tested my memories with memtest86 with K8M neo-v mobos and several 754sockets mobos
for more than 24hours,and there was no errors at all.
I just found out with my K8M neo-v to shut up the beeps
juts disable to show the full screen logos from the BIOS and it will boot with only one beep.
I really dont know if it will work fine for the other guys mobo,but so far,mine is working with no problems.

New Samsung SATA hdd not detected by K8T800 Pro

I've been banging my head against this all morning, can't figure it out.
The BIOS I have (which is supposedly the most up to date version according to the live update) doesn't auto-detect the SATA hdd. My IDE drives are there, an old zip drive is there, etc but it doesn't see the SATA drive. I'm using an IDE hdd for the OS, the SATA hdd is for back-up purposes only.
Any tips on how to get this damned thing recognized? I've been following various instructions online for awhile and nothing works so far.

Quote from: Hans on 28-January-09, 05:07:12
Nonsense about the WD or Samsungs not working by the way. All work, you just need to set them right. And at this time, I wouldn't go for either Seagate or Hitachi. Too many problems with those brands, but that's some point to discuss somewhere else.
Really, nonsense?
VIA have issued a statement on this years ago:
Quote
CHIP FIRM VIA issued a note to its customers telling them of problems with chipset support for hard drives using the Serial ATA II standard.
It said that VT8237 and VT8237R chipsets don't provide forward compatibility for S-ATA II, which is important as hard drive makers are beginning to manufacture this type of drive.
But Via is readying the release of VT8237R Plus, which will solve the problem. This means that motherboard makers that use the former chipset should clear their inventory before September.
Hard drive manufacturers position with S-ATA II is as follows, said Via in its note. Western Digital and Samsung are already shipping these devices, while Seagate and Maxtor will start shipping them during this quarter.
If you connect S-ATA II drives to an old Via chipset which includes the VT8237, VT8237R, VT6420 and VT6421L, the devices won't be detected.
Some mobo makers, such as Epox, have already responded to the problem and have warned their customers to seek the support of hard drive vendors. In a letter to its customers, it said that they should also check the specs of other manufacturers' Via based motherboards.
Do some googling, it has been all over the net for years. I have had a couple of these boards and a fair share of different hard drives. Trust me, not all of them work on this board.

MSI Neo 875P Mobo monitor blank....

Hi,
I'm running TwinMos DDR 400Mhz with 2 pairs of 512MB.
Each time it reboots or switch on my system....the intermittency problem appears that my monitor screen blank while the CPU is working.
Sometimes it work by resetting or switching off & on....to get it solve tempoarily.
Running a P4 800FSB 2.8C Ghz.
SBLive! Soundcard.
seagate sATA HDD 80GB
Yamaha SW1000XG soundcard.
Matrox G400 display card
300Watts HEC PSU.

Hello.
This board doesn't works well, or in some cases like mine, won't even start with twinmos memorie modules.
I sugest you get another memory stick, from another manufacturer, and try it out. It worked for me.
I bought OCZ and my system is working rock and stable, even in agressive overclock.
good luck and, let me know. 8)

Seagate 160 SATA Drive & Neo-FIS2R mobo

Everyone, I need your help for a newbie.
I have installed a Seagate 160mb SATA drive as my primary bootable drive on a Neo-FIS2R mobo. I have successfully moved my partitions etc from the previous drive (80GB Seagate IDE drive).
The system boots fine, Windows XP sees the drive but everytime Windows XP starts, it pops up messages saying New Hardware found and tries to install the SATA drive under the IDE ATA/ATAPI Controllers section in Device Manager.
Under this section in Device Manager, I see 2 IDE Channels defined with yellow circles and exclamation marks inside the yellow circles.
I have 1 IDE drive attached as well and maybe later another IDE drive will be added.
What settings do I need in my BIOS? Are there drivers required to be installed in Windows XP?
Thanks for your help. This is driving my crazy!

In bios under Integrated Peripherals, On Chip ATA Operating Mode set
Native Mode
ATA Configuration - PATA only
SATA Keep enabled - yes
PATA Keep enabled - yes
PATA channel selection - both
This should let you boot from the SATA and see the PATA.

Again: Cool`n Quiet and K8m Neo-V

Working on a new computer for my wife. She wants her new computer to be quiet and powerful (no gaming), so i bought MSI K8M Neo-V and athlon 64 2800+. I have two problems now:
1 I had the same problem as described in an earlier post, it would not post after enabeling cool`n quiet. A bios upgrade fixed that. But: The fan speed does not go down ! Win Xp tells me the cpu is running at 990mhz, but the fan is still going at over 3000rpm. This must be wrong?
2 I bought 256 Mb ram (TwinMos PC3200). But the motherboard tells me its only 196 Mb Win Xp says its 192 Mb of ram... Is this a motherboard problem or faulty ram? Didn`t help putting the ram in the DIMM2-socket. Any suggestions?
Thanks, great forum

Thanks bosskiller, great link to the cool`n quiet FAQ. I understand now, that its up to the mobo-producer to give us a way to adjust fan speed. As far as I have found out, MSI have not given us this important possibility yet. The newest bios (ver. 3.2) does not adjust fan speed automatically, and there is no way to do it manually.
The newest version of CoreCenter from MSI does not support this mobo yet (I think)(it does not controll the fan, but it gives you the rpm). New versions of the bios and/or CoreCenter can fix this, I hope. Otherwise we must buy technical regulators like Zalman Fan Mate 1.
About Ram: I think bosskiller is right about the shared memory, the VGA part occupies 64 mb ram. CPU-Z reports the ram-module as 256 mb. The os only gets 192 mb.
I bought only 256 mb ram, TwinMos PC 3200, single banks I think. I was planning on using my old windows millennium, and save some money on both os and ram.
The ram is running 400 mhz, no problem there.
I use Zalman ST-300BLP power supply. 300w, 15A for the 12V. I dont think the power supply gives me any problems. I have used it with my P4-system before, no problems there either.
(I use thermaltake fanless power supply with the P4 now, and its great )
The athlon64 system looks very quick, if MSI solves the fan speed issue, this system is going to be great!

MSI x48c platinum - does not detect SATA HDDs

I am having some problems with a pc build with motherboard not detecting SATA HDDs (MIS x48c Platinum).
I believe I have exhausted all other avenues, and I would appreciate some help if I have missed something obvious.
(details of other components are listed at end of mail).
When I built pc using these components, and went into BIOS settings, the SATA HDD's were not detected. I tried changing BIOS settings, but no difference if SATA, AHCI, or IDE settings.
I removed the HDDs and successfully tested them in another machine (also formatted them while had them istalled in other pc).
IDE optial drives are detected. I have tried to boot with these disconnected to ensure no isues with both IDE and SATA drives connected, but this did not resolve issues.
I have also tried connecting HDD to different onboard SATA ports, and connecting just one drive with no success.
Resetting BIOS defaults, and using clear CMOS reset did not resolve issues either.
Sometimes on boot, it takes a few attempts to boot correctly, and on these occassions I receive an error message "Warning !!! The previous performance of overclocking is failed, and the system is restored to the default settings, Press any key except "DEL" to enter setup ......." I haven't tried to set any over clocking.
I read about a number of issues on MSI forum related to SATA drives which were resolved by BIOS upgrade (mobo was shipped with v.7.0 released 20 March 08). I managed to install an old IDE HDD and flash BIOS, but still no resolution of issues detecting SATA drives (BIOS V.7.2 released 29 July 08).
I've tried everything I can think of at this stage. Is there anything else I should try, or is there something wrong with this motherboard?
Spec:
Motherboard:
343949 MSI X48C Platinum, X48, Socket-775,
DDR2/DDR3, ATX, GbLAN, 2xPCI-Ex(2.0)x1
Other components in build:
CPU Intel Core 2 Quad Q9550
Graphics Sapphire Radeon HD 4870 512MB
HDD 2 x Samsung SpinPoint T166 500GB
RAM 4GB (2x2GB) GeIL DDR3 1333MHz Value Dual Channel (7-7-7-24) PC3-10660
PSU 700W X-Power ATX SLI PSU
ODD DVD & CDR drives from an old pc - IDE connections.

i just remember i had once similar problem with a sata driver. the issue is this you can not adjust everything in bios in one go and expect mobo to know about it. what i mean is this for instance you disable the raid then you save it and exit and then when it reboot you go back to bios and reset another another parameter, you save and exit and on reboot you go back to bios and reset another parameter. i got round the prob that way and it worked and mobo saw the sata HDD. give this a shoot good luck and finally make sure raid is disabled
this is what i would do
1- make sure the jumper setting on your IDE Hdd is correct (Y may have to try this twice as there are two different setting on jumper setting for Master)
2- connect the sata HDD
3-click on power
4-go to bios and disable raid save exit
5-on reboot go back to bios
6--on first option click on it then you should see all devices that can be seen by mobo if you do not see sata HDD you have to click on enable for the auto to see the device once it sees the device save and exit. REMEMBER THE JUMPER SETTING ON IDE HDD CAN CAUSE PROB . SO try the other jumper setting for master, repeat this procedure once more hopefully you get it right

Lose Seagate SATA when A: Boot

I have tried numerous boot disks and there all the same
c: invalid drive....... F**K I am running an Seagate SATA 120G ....23A. It seems Auto detect looks for the drive during normal booting now as before it flashed and then it was gone. My Lite-on won't do jack either
Does the controller or require a DOS driver to detect SATA?

your drives ntfs,a boot disk cannot read it only fat 32
http://www.msi.com.tw/html/support/bios/note/ntfs.htm
if trying to flash bios

MB-848P-VMSI 848 NEO-V P4 Intel 848P FSB800 SATA A&L Motherboard

I am building a machine using the MB-848P-VMSI 848 NEO-V P4 Intel 848P FSB800 SATA A&L Motherboard with 512M of RAM, a P4 1.5ghz Socket 478 CPU and an older Matrox Marvel 32M AGP video card.
I put it all together and attempted to boot, but I get no post-beep code and no video. However all fans and hard drives do spin up. Usually I am able to determine the problem by process of elimination by removing or swapping CPU or RAM, but I get no results. No matter what I do, no sign of video and no post-beep codes.
Any suggestions?

Your mobo does not support the 1.5GHz Williamatte CPU that you want to run.
http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_cpu_support_detail.php?UID=596&kind=1

MSI K8M Neo-V Motherboard - No Display on Boot

I have K8M Neo-V motherboard, when i power on my pc there is no display on monitor.
No error beeps comes on POST. Processor Fan is running properly.
I checked my Monitor and RAM, it working fine on other pc's.
what could be the problem? Plz any one can help me to solve this issue.
Thanks in Advance.

Quote from: Henry on 27-January-12, 13:37:49
Read the >> Posting Guide <<
Tell us what parts are in the PC. See my signature below for an example of information to provide.
Hi,
MSI K8M Neo-V (MS-7032-Ver:1)
BIOS: AMIBIOS SS53 (8758)
Processor: Athlon 64: 2800+
RAM: 1 GB - PC400
VIA® VT8237 Chipset
HDD- 80GB SATA Segate

Mac OS wont recognize new Seagate SATA hard drive...

My original seagate SATA 250G drive failed, trying to replace it with a Seagate 2G SATA, booting up snow leapard from the disk, Disk utilities doesn't detect the drive at all, so I can't reformat or partition it. Read some info from seagate, but don't understand why i might need a host adapter card if the computer already had a SATA drive in it already... Any suggestions before I give up? It is an old mac pro, first or second gen, used it all the time and has never failed me until now. Both the broken drive and new drive are internal drives..

You should not need a Host adapter to install a SATA drive in a SATA bay.
But any mis-alignment at any stage can cause the drive connector to hit, rather than engage the backplane connector. The drive connector must fully mate with the connector at the back of the bay.
• You must snug, but not over-tighten the screws at each position with the exact correct #0 Phillips screwdriver to get comparable torque on each screw.
• The drive must then be inserted so that each roof tang catches the correct part of the sled. If one is bypassed the drive will be cocked in the bay and not mate.

Newbie... AMD 64 with K8M Neo-V can't get it to work

I just resently purchased a bundled motherboard and processor from CompUSA, AMD Athlon 64 Processor 2800+ with a MSI K8M Neo-V with VIA K8M800 + 8237 Chipset also puchase (2) 512 DDR400 PC3200 sticks. I'm replacing an old Gigabit motherboard with this one. Installed everything per spec, did not connect any device as of yet, just wanted to make sure the board would boot up with main harddrive first. I'm using the onboard video,went I power the system up I get nothing, no BIOS Setup screens, no video, nothing.... What have I done wrong ???
Any help would be greatly appreicated...

hi to all~~
i have just got the same mainboard yesterday, but got a lot of problems since the first install of software.........
i got a whole new unit with the following spec:
MSI K8M Neo-V
AMD Sempron 64-bit 2600+
Kingston 512MB DDR RAM
Maxtor 80GB SATA HD
LiteOn CDRW
and an internal modem
First problem:
after the 1st installation (win98se + all drivers given), the computer showed that the "Programmable interrupt controller" (under device manager) causing a resource conflict (code 15). I tried to change the resource but a window popup and said : "This resource setting cannot be modified" .
Action Taken:
1) format the HD and reinstall win98se. With no driver and any software installed, i checked the device manager and found the "Programmable interrupt controller" still causing a resource conflict.
2) from 1), i installed and updated the chipset controller but got no change..............
3) from 2), installed and updated all drivers, but the problem still there......>_<
Second problem:
After I installed the VGA driver and restart, I tried to adjust the resolution but always come out a "Rundll32" error......
Third problem:
System is unstable. When I copy files from CD drive to HD, after a few minute (copy in process) it will come out the blue screen .....>_<
also sometimes when i restart after installed the drivers, or switch on my computer, the computer will restart just after the windows98 logo dissapear, strange........
help me~~~
thankyou

K8m neo-v mobo dont detect seagate sata hdd st3808110as

Similar Messages

Maybe you are looking for