K8n Diamond and sil3132 BIG PROBLEM.

Hi, i have K8N Diamond and i can't enable sil3132 controller in the bios ... because there isn't a settings !!!
I know, it seems to be amazing, but it's true, it doesn't appear the setting of onboard Sil3132 RAID chip, i can't watch the Setting options: [Enabled], [Disabled] and mode settings [SATA], [RAID]. under INTEGRATED PERIPHERALS > ONBOARD DEVICE.
I never watch the screen on Sil3132 bios !! ad i never enter on it with F4 or CTRL+S key.
I'm testing all version on Diamond Bios from 1.0 to 1.6 but no one can show me the Sil3132 settings.
What's up? it's amazing ... i think that Sil3132 is damaged ...
Someone can help me?

Quote from: Wonkanoby on 15-August-05, 02:03:36
unwanted stand off under board shorting it ?
mmm ... interest ... i go to see it.

Similar Messages

K8N DIAMOND and MAXTOR 200Gb ATA size problem

Hi all forum! i´m new here. I have a MSI K8N DIAMOND SLI board, all is ok but the Maxtor DiamondMax Plus 9 200gb is only 33gb in the Bios and in Windows XP SP2. The Jummpers are fine and i chaged it for all positions and the result was the same.
And in the Maxtor page it says
https://maxtor.custhelp.com/cgi-bin/maxtor.cfg/php/enduser/olh_adp.php?p_faqid=1062&p_sid=3mOkRPXh&p_lva=#
The Solution 1: I reformated the hard drive severals times and the same result :(
The Solution 2: I have de newer official bios 1.7
The Solution 3. I have formateated with ntfs
I don´t know how resolve this problem, thanks for your time reading my post and sorry for my bad grammar.
See You!

On K8N Diamond the Sil3132 is a Raid5 controller. You can only install Raid5 driver (SataLink and SataRaid drivers don't work, only SataRaid5).
Use the latest driver version 1.2.3.1. You can download it from MSI.
If you don't use Raid, then you must go into the Silicon Image bios setup utility (CTRL+S or F4, when displayed) and set for each drive a JBOD array (Create Array -> JBOD).
(On newer bios JBOD has changed to CONCATENATION.)

K8N Diamond Silicon Image SATA problem

Hi everyone,
I have a problem with my Silicon Image controller,
when I installed WinXP and tried to install drivers for the
Silicon Image controller (in SATA mode) it don't exept
Silicon Image SiI 3132 SATALink Driver 1.0.0.9.
The only drivers Win exept is RAID drivers. But then I can't use them because
I dont use RAID array.
I have tried to update the BIOS without any luck.
Is it the MB thats is broken or is it Win that has f***ed up?
My specs:
AMD Athlon 64 3700+
MSI K8N Diamond
4x Kingston HyperX 512MB DDR PC4000 CL3 (3-4-4-8-1)
HIS Radeon X850XT PE 256MB VIVO
1x WD Raptor 36GB 10000RPM
1x Maxtor DiaMax Plus9 120GB
1x Maxtor DiaMax Plus10 300GB
1x WD Caviar SE 250GB
3x Maxtor MaXLine Plus II 250GB
(all SATA HDD)
Creative Labs SoundBlaster Audigy 4 Pro
Plextor PX-716A DVD-R/RW/DL
Windows XP SP2
Zalman Reserator 1

On K8N Diamond the Sil3132 is a Raid5 controller. You can only install Raid5 driver (SataLink and SataRaid drivers don't work, only SataRaid5).
Use the latest driver version 1.2.3.1. You can download it from MSI.
If you don't use Raid, then you must go into the Silicon Image bios setup utility (CTRL+S or F4, when displayed) and set for each drive a JBOD array (Create Array -> JBOD).
(On newer bios JBOD has changed to CONCATENATION.)

Newbie K8N Diamond and 4400+ DUal core

Hi
I recently put together a k8n diamond and a dual core 4400+ processor. SInce i am no so fluent with voltages etc... I tried running the Ntune "performance Tuning wizard". Whereas all the other utilities work fine .. this just does not run.... if i click nothing happens (like a dead link icon)....
I reinstalled, redownloaded etc.... several times... anyone have a solution ?
Is there alternative software that can optimally configure my memory voltage, cpu voltage, FSB etc.....
My system is slightly unstable and crashed sometimes at the moment.
Another thing i noticed is that my HD (Seagate 80GB SATA - ST380817AS) is showing on secondary channel (hardware, device manager, IDE/ATA COntroller, properties.... with theoretical burst 10Mb/s burst 113Mb/s sustained 59Mb/s)...is this right ?
Thanks for your help
Matteo

Wow MatteoB, youve got a bunch of issues going on there...
-First off, try to keep posts to one issue, the ntune, the system instability, the hard drive problem, its hard to respond to-
-Please put all your system components in your signature, it's basically the first item in the new members to do list, suprised the moderators didn't snipe your for that, but most folks probably just passed by due to the first problem-
+The nTune Performace Tuning Wizard and the Profile Module does not work with dual core cpu's (i've only unoffically confirmed this with a handful of others), however you can manually change some settings in the Adjust settings screen+
++If your system is unstable at stock default settings and speed, you need to fix this the old fashioned way, ntune does not do this for you++
The hard drive problem sounds like it can be fixed, but again a remedy for system crashing should be your #1 priority as it may be tied to the hdd.
Make a signature file with your system components and elaborate on what is happening on the computer when it crashes and I am sure you will get a lot of responses.

K8N Diamond and NO POST

I have a big problem with my new K8N Diamond, it will not go to POST. No beeps no nothing.
First the configuration:
MSI K8N Diamond
2x512 mb Corsair PC3200 TwinX XL PRO
2x Seagate Barracuda 7200.7 160 GB NCQ 7200rpm SATA
AMD Athlon FX-55 socket 939
1x MSI Geforce 7800GTX 256 Mb SLI VIVO PCI-E
NEC Duallayer 16x DVD R/RW
Tagan TG580-U22 580w PSU, see link Electric Specification
Electric Specification
Max. total power 580W
AC input 100~240VAC; 60/50Hz, 10/6A
DC output +3.3V +5V +12V1 +12V2 -5V -12V -5VSB
Max. output 26A 30A 20A 20A 0.8A 1.0A 2.5A
combined current 32A
Max. combined 180W 420W 4W 12W 12.5W
I have tried the following:
- Removed all power consumption like fans and IDE units with only CPU and PCI-E connected
- Removed the MB from the chassi and put it on cardboard with only CPU and PCI-E card on power
- Removed one memory stick
- Tried with second memory stick in different position
Nothing happens. The fans are spinning on the CPU but no POST. I though it was lack of power so I bought
the Tagan PSU which was the biggest I could find, but it did not help.
Is there problems with the BIOS and FX-55 that I should know about? Or is it the MB that could be dead?
Hope someone could help me. I did not miss the 4-pin connector for power the CPU.
Many thanks in advance.
Stefan
Sweden

Hello,
I also had a K8N Diamond board with the same problems you are listing here.
In the end, I had to get it exchanged by another one. The one I got then
was the K8N SLI Platinum (also MS-7100 Ver. 1.0)
It has most of the features included on the K8N Diamond, except the following:
Sillicon Image SiL Serial ATA Controller Chip and SATA ports 5 and 6 : Gone.
Marvell Yukon LAN Controller Chip and Second RJ-45 Ethernet port : Gone.
Voltage Regulartor Active MOS Fan : Gone.
IEEE 1394 Firewire Bracket : Gone.
K8N "Diamond" Full Screen Logo : Replaced by K8N SLI "Platinum" Full Screen Logo.
About all other features included in the K8N Diamond mainboard (MS-7100, Ver. 1.0)
Active MOS Fan Connector : Still there and functional. You can plug a compatible fan there, to cool down the Voltage Regulator, if you want.
Creative Sound Blaster Live! 24 Bit : Yes, and complete with all audio ports, including Optical and Coaxial plugs for 7.1 Ch audio.
Back I/O IEEE 1394 FireWire Port : Yes
On Board IEEE 1394 FireWire Connectors : Yes
D-Bracket 2 : Included in the box.
10 USB 2.0 Ports : Yes. 4 on back I/O, 2 on D-Bracket 2, 2 for Case USB 2.0 Ports, 2 for internal use or additional back USB 2.0 bracket.
which can be an MSI USB 2.0 Bracket, a Modified MSI D-Bracket 2, or a USB 2.0 bracket, from Belkin or any other
brand, or a generic USB 2.0 Certified bracket.
Everything else is on this board, is exactly the same as with the MSI K8N Diamond. My advice for you is to get your MSI K8N Diamond exchanged by an MSI K8N SLI Platinum. Beleive me, this board doesn't have the problems most K8N Diamond users are having, and for me who once had the K8N Diamond mainboard, it is the best alternative comming from MSI. It's the same model, but without the extras I mentioned above.
I highly recomend this one

ATTN K8N Diamond Plus Users - SLI problem

i need help diagnosing a problem:
i installed this board last night, transplanted my a64 4000+ along with 2 7800gt's and a brand new antec 550w psu. i did the live update bios flash (dont recall what version i am running now) got my e/n and audio drivers in place etc.
when i enable sli, the machine freezes when i fire up a game. both cards are plugged in properly, i tried swapping the slots they were sitting in, i tested both cards individually and they are good, i reversed the sli bridge just in case, reverted to fail safes in the bios,
i cannot play games in sli mode, in single card mode i can (I THINK... i am afraid this might be a heat issue, but i put plenty of fresh arctic silver on my proc, FEAR seems to freeze regardless if i am running sli or not..i will have to double check when i get home from work)
has anyone experienced anything similar? i am running fresh drivers and this is my first sli build so maybe i am missing something... i have been racking my brain for the last 12 hours, i dont think its the ram, could it be the northbridge chipset driver? i installed the one off the disc, but i didnt check the site for a newer one...
thank you so much for your time.

Quote from: kakarocht on 08-February-06, 13:58:02
Do not used liveupdate to flash the bios. Used from the program files itself. Refer from my sig on the flashing the bios. BTW create your own sig and gives more details about your peripherals and psu in details. What my concern is your PSU problems. Could you gives more details your PSU? Have you tried to install new drivers from NVIDIA??
the psu is a brand new antec 'true power 2.0' unit that i bought from newegg...in bios the 12v rail is showing 12.3 which might be a little bit high...but it is stable for what its worth...
here is my setup, i will create a sig shortly:
2gb PQI ram DDR400 running at stock speeds, not sure of the latency but i am thinking cas2
A64 4000+ Clawhammer proc running at stock 2.4ghz speed, 1mb cache
MSI K8N diamond+
dual 120gb maxtors
sony dual layer 16x dvd
stock cpu fan.
shitloads of AS7
another curious fact:
since the upgrade FEAR doesnt want to work at all... DOOM and COD2 both work in single card mode...but FEAR will freeze on me mere seconds after the first map loads...
i dont know what the culprit is...but i bet im gonna kick myself when i find out...
im gonna go re flash my bios now...
thanks for the input, its always greatly appreciated.

MOVED: K8N Diamond Plus Motherboard overclocking problem.

This topic has been moved to Overclockers & Modding Corner.
https://forum-en.msi.com/index.php?topic=93776.0

Quote from: TimeReaper on 15-February-06, 09:15:17
I know this board can reach 300+ by reviews by Tom's Hardware. But I was wondering how I could get my FSB up there? I can't seem to get past the hurtle at 270. Anything above this will make the system fail to start up and I have to clear the BIOS again.
I lowered the HT to the equivalent of 3X, and CPU Multiplier to 8X using a venice core 3500+. I even tried adding voltage to the HT. I'm wondering if I'm missing something in this equation that stops me from getting 300+ FSB? The overclockable items are too many and unexplained.
If someone could spread some light on what else needs to be done, please tell me.
My system is as follows.
MSI K8N Diamond Plus
AMD64 3500+ Venice
OCZ DDR600 Platinum Elite
520 OCZ Powerstream
2x Samsung 200G@Raid 0
Zalman CNPS 9500 LED
Sapphire GTO2
Hi dude,
I have the similar problem as well. Sounds like you are in the bad shape, but yeah, try to loose your RAM settings. First, all settings auto seem to be good, but it's actually not the case. You have to set TRC and TRFC as higher than 12 and 14. I am seeting those to be 14, 18, and it seems to be working great. It will be better to set the burst length as 4 beats. I don't like this board coz I can't set the drive length to be weak instead of normal detected by the Windows. My system can post, but I got problems of playing 3D demos and games, which looks like it's the problem of motherboard. Not mature enough.
My rig:
AMD Athlon64 3700+ @ 2.7GHz
OCZ Platinum Elite DDR600 2.5-4-4-10 Dual Channel
Leadtek PX6800GT @ 425/1200 at 2nd PCIe slot
2 x WD 120GB 7200RPM + Samsung 160GB HD

K8N Diamond Plus Power on problem

I have this problem with the board where I shut down windows, and it does shut down by the way. But the strange thing is that right after it powers down, like say a second, it restarts itself as if I pressed the power button immediately after. Though I can correct this by pressing power again while it is still going through the motherboard check ups, I was wondering if someone had similar problems. If so, if there is a solution to correct this bug?
I am currently using the 1.16 version patch.

CPU=Opteron 170
Motherboard=MSI K8N Diamond Plus
Videocard=Sapphire X800GTO2
Soundcard=Creative X-Fi
Hard drive= 2x RaptorX 150GB @ Raid 0
PSU=OCZ Powerstream 600
CPU Cooler=Zalman CNPS 9500LED
3x 80mm exhaust fan
1x 120mm intake fan
1x Vortex 2 Intake crossblower
1x Slot Exhaust
1x Antec Vcool Intake
I'll check on that wake lan thing.

K8N Diamond Plus audio out problem

Hi,
I'm having an issue with the audio out on my K8N Diamond Plus. The rear audio out works fine when left jumpered. However when I connect the front panel audio connector to the mother board the volume of the rear audio out drops to an almost in audable level while the front panel audio works as expected.
At first I thought the rear audio had been completely disabled until I tried turning my speakers all the way up.
Is there a software issue here?
FYI I'm trying to use the front pannel audio connection on a Silverstone TJ07 case.

hey - mikein_texas here - i have same board but with a Centurion case -
couple of things i ran into - maybe will spark some ideas
initally i hooked up front panel audio and got nothing
then i read on page 2-19 of manual that 5-6,9-20 have to be jumpered for rear audio to work
but that means no front audio which was a drag - but solved that prob with usb mike and headphones
apparently unless i am reading it wrong and someone please correct me if so, but you can have front audio OR rear audio
BUT not both
again look at page 2-19 in manual and specifically at text in grey box in middle of page
Yukon PXE 2.01 ( 20040406 )
Pre-boot Execution Environment PXE v.2.1
DLink Cable Modem - model DCM-202
ViewSonic VX2025WM 20.1" Widescreen TFT LCD - 1680x1050, 800:1, 8ms
MSI K8N Diamond Plus Socket 939 NVIDIA nForce4 SLI X16 ATX AMD
SAMSUNG Black 1.44MB 3.5" Internal Floppy Drive Model SFD321B/LBL1
SONY Black IDE DVD-ROM Drive Model DDU1615/B2s
XFX Geforce 7600GT PV-T73G-UDD3 Video Card
SAMSUNG 16X DVD±R DVD Burner - 5X DVD-RAM Write and LightScribe Black ATA/ATAPI Model SH-S162L/BEBN
COOLER MASTER Centurion 532 RC-532-SKN1 Black Computer Case
AMD Opteron 165 Denmark 1000MHz HT 2 x 1MB L2 Cache Socket 939 Dual Core
CORSAIR XMS 2GB (2 x 1GB) 184-Pin DDR SDRAM Unbuffered DDR 400
Seagate Barracuda 7200.9 ST3808110AS 80GB 7200 RPM 8MB Cache SATA 3.0Gb/s Hard Drive
Ultra ULT31849 X-Finity 600W Power Supply
Cooler Master A12025-12CB-5BN-L1- 120 x 120 x 25mm 1200rpm, 43cfm, 22dBA, LED, 3-pin - front intake case fan
Scythe S-FLEX SFF21F 1,600rpm, 49.0CFM, 20.1dBA, 3-pin, 120mm S-FDB Bearing - rear exhaust case fan

Yosemite and mail - BIG problems with memory leak

Our small company has had significant problems since upgrading (?) to Yosemite, which by all we could glean from Apple would be a relatively bug free install. At random times, usually while composing an e-mail, the mail program will just spike in memory consumption, going from a couple hundred Mb of RAM consumption to over 70 Gb in just 3-5 minutes. This obviously causes the entire machine to come to a standstill and the mail process needs to be killed. A cascading problem is that when this happens any other programs will also become non-responsive, and they also will need to be killed, often at the loss of work. I've talked with the support people at Apple and disappointingly they seem to be unaware that this is an issue, or more likely they are aware of it (I mean, just do a search of "Yosemite mail memory" and see what you get) and want to downplay that the release has been a HUGE failure for MANY people. After about 20 of these application memory events since upgrading over this past weekend at our company I would like to see where Apple is on fixing this. BTW Apple, your user base is fairly sophisticated with computing, and having your online assistants continue to try and point the problem at the users - who are all having the EXACT SAME ISSUE - is alienating your user base. I've been using Apple for over 20 years and this is the worst release you've ever had. I think you're well on your way to becoming Microsoft in 1994, we need the old Apple company back.

I have the same problem and after a few days I am thinking seriously about abandoning Apple mail and .... going back to Outlook, I do not like MS, but may not have another option. Any suggestions.
I am amazed that Apple does not give any information about the problem. It does look like they are loosing their touch and appear to be following the Microsoft and Blackberry path.
Within a small company like mine, another few days of this and it will be impossible to keep it.
Hate to say it, but for the first timewith Apple I miss the old OS, it did not look as good but at least it worked..

P4N Diamond and Pentium D problem

Hi,
Have just bought the P4N Diamond motherboard, and a Pentim D 830 processor.
When switching on the status led shows four red lights. According to the manual this means that the processor is defective.
Have taken the processor in and out many times, but no luck.
Any other ideas ? Any assembly errors I could have made ?

IJRC, For your set up do the following:
The best way to get your system up to make sure that you have BIOS version 1.3 and up. Any BIOS version before this will not see the Pentium D. If you dont have this BIOS or are not sure it might be best if you call MSI and have them send you out a BIOS chip with the updated BIOS version on it.
-Make sure that you only install windows with one stick of RAM
-Do not connect any USB devices untill windows is up and running.
-Your MOBO takes alot of power, so make sure that you have a quality PSU as well as it having plenty of amps on the 12v rail. (As per the P4N manual p.10, 450watts and atleast 20amps on the 12v rail is recommended for system staibility.)
-Drivers for me were not that much of a problem except for my monitor, but my GPU sees it for what it is and thats what matters. Ofcourse if you dont have the internet up and running getting drivers might be a problem.
- As long as your follow these steps you should be fine with installing windows 64x. To be safe just download the Marval Lan Eathernet Drivers and burn them to a cd before you start your build. That way you can access the internet to download 64x drivers. For the most part you shouldnt have a problem getting drivers...if you have an hp printer you will have a problem though.
GL and write back if you have problems...i think that i have been through them all with this MOBO and the Pentium D. However with the help from this fourm i think that i have everything under control.

Msi Diamond and four memorycomps - problems?

I have installed four 512Mb ddr566@500 comp's and now when I have used the machine a while, winxp will pop up a blue screen. The machine will restart then (so quickly, that I can't read the errormessage).
Before I had two 512Mb ddr566@500 comp's, without problems.
Is this board unable to handle four memorycomps, or what might be the problem? I have already ran memorytest succesful. In the manual reads, that when using four comp's, the maxium speed is ddr333? The cpu is Opteron148, with venus core.
Edit. BTW can someone say, is my PSU strong enough to run whole machine. It is Tagan 2force 480W and machine: Msi diamond, 148Op, 2Gb ram, 2x 6800 ultra, 2x hdd, audigy4 pro, 3x 120mm casefan. When I plug two more hdd's, nvidia system will show error, that power is not enough to graphic cards. The manual says, that the mainboard want 450W or more psu.

MSI always have the color code for vdimm.
It's what the vendor of the modules state for nominal voltage that counts .
If they say 2.8 i would run 2.8 or higher (not below) . 0.05 higher to compensate for voltage drops during load.
Double 6800 Ultras (stock clocked) pci-e draws something around 70w from the +12v line each in full 3D mode/load. (in idle 2D mode about 30w each)
Thats almost 6A per card , times two it's 12A just for your graphics in the highest load situation .
I'm not sure though if SLI balances toe load exactly equal , but lets assume so to be sure .
Then atleast 8-10A from +12 goes to your cpu depending on model and if overvolted/overclocked .
And consider apx. 1A +12v usage for each HDD and optical (although the use a bit more at spinup , but then the gfx's are in 2D mode) .
1A +12v for mobo .
Fans run off +12v .
Memory runs off +3.3v or +5.0v depending on motherboard design .
Add things up and have a rule of using a load target for the PSU @ 80% (fully loaded PSU's loose efficiancy and stability .
There is some guideline of SLI building and dimensioning of PSU you might wanna check out over at nvidia .
http://www.nvidia.com/object/slizone_howtobuild_2.html

Log and capture big problem

I am using FCP 3 (fully registered) i hit the log and capture NOW feature, and the screen brightness drops in half and a message that says I have to restart my computer and freezes up my computer. The message is in 4 different languages making me think that it may be a computer error rather than a FCP message.
I deleted my FCP plist file, and the FCP user data, preference file and the POA cache file. Problem is still there.

That's a kernel panic - whole system stalling.
Do you have both FCP 7 and FCP X installed?
If so, did you follow installation instructions provided by Apple:
http://support.apple.com/kb/HT4722

Excel with powershell and this big problem of locale

Hi Folks, I'm getting C R A Z Y with this Excel/Powershell Stuff...
MY display language is EN
My input language is fr_CH
the following code :
function Invoke([object]$m, [string]$method, $parameters)
$m.PSBase.GetType().InvokeMember(
$method, [Reflection.BindingFlags]::InvokeMethod, $null, $m, $parameters,$ciUS)
$ciUS = [System.Globalization.CultureInfo]'fr-CH'
$objExcel = New-object -com Excel.Application
$objExcel.visible = $True
$ci = [System.Globalization.CultureInfo]'fr-CH'
$objWorkbook = Invoke $objExcel.Workbooks Add
$objWorksheet = $objWorkbook.Worksheets.Item(1)
$objWorksheet.Cells.Item(1,1).FormulaLocal = "A value in cell A1."
Invoke $objWorkbook SaveAs "C:ScriptsTest.xls" > $null
Invoke $objWorkbook Close 0 > $null
$objExcel.Quit()
throw me the error :
Exception calling "InvokeMember" with "6" argument(s): "Object does not match target type."
At line:3 char:1
+ $m.PSBase.GetType().InvokeMember(
+ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+ CategoryInfo : NotSpecified: (:) [], MethodInvocationException
+ FullyQualifiedErrorId : TargetException
You cannot call a method on a null-valued expression.
At line:11 char:1
+ $objWorksheet = $objWorkbook.Worksheets.Item(1)
+ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+ CategoryInfo : InvalidOperation: (:) [], RuntimeException
+ FullyQualifiedErrorId : InvokeMethodOnNull
Basically this happend when you have english Excel with non english locale.
My OS is in english but my Keyboard is in French-Swiss.
Please help me I'm getting crazy...
MCITP Enterprise Administrator / Server Administrator

This might be helpful.
http://dmitrysotnikov.wordpress.com/2008/02/22/powershell-help-broken-on-localized-versions-of-windows/
The problem seems to be that PowerShell v1 for Windows Vista and PowerShell v2 CTP for all systems are storing the language neutral (English) help system in the en-US subfolder of the PowerShell folder.
On a localized versions of Windows, PowerShell seems to be looking for a subfolder with its own locale (e.g. de-DE for Germany, ru-RU for Russia, and so on) and does not fail over to en-US if the folder is not found.
RESOLUTION
Apply the language pack for your language so your local version of help gets added to the system.
If the language pack is not available, copy or rename the en-US folder to match your Windows locale. To learn your locale run the following command in the PowerShell prompt:
[System.Globalization.CultureInfo]::CurrentUICulture
Thanks Azam When you see answers please Mark as Answer if Helpful..vote as helpful.

HT1222 my husband didnt realise that he had up graded to iso7 and having big problems volume is very low now how can he get back to what he had

has anyone else who have upgraded to this found that the volume is as loud and how do you close apps i like my husband am very confused and dont intend to upgrade my phone to this

Hi.
I do not know if my bios is correct one but i did not have the problems like you.
I think you can try
Picture before backup
But i provide file only...all you do with them is at your own risk
65CN15WW
i used to backup : Universal bios backup utility
EDIT: i tried to reflash 65CN15WW by using autoexec winflash variables i get message EFI error unsupported BUT after that i only ran winflash.exe and set to only flash new bios option. Then select bios file to flash click on flash new file button and pray
After restart my BIOS still working i don't tested it with 65CN13WW but you can try if it helps.
i think this settings creates problems with invalid bios image
and i flashed using this
Lenovo IdeaPad U410, Core i7 - 3517U, 8GB RAM 1600 MHz, 1 TB + 24GB SSD HDD, BIOS: 65CN15WW
Windows 7 Home Premium -> Windows 8 Pro RTM (upgraded without problems)

K8n Diamond and sil3132 BIG PROBLEM.

Similar Messages

Maybe you are looking for