K8N Diamond - Bluescreen after Win XP (SP1) Install
Hi. After building my system today I installed Win XP (SP1). The pre-install and graphical install went fine with no errors. On the first boot after the install, the Win XP logo appears for 5 seconds, there is then a quick flash of bluescreen then the system resets. The system is booting off of an Adaptec 29160 SCSI Controller with SCSI HDs. IDE is enabled in the bios for DVD & DVD Writer and the SATA controller is disabled in the bios. I did not use the Nvidia or Silicom SATA drivers during the initial OS install since I had disabled the onboard SATA/RAID controllers.
If I boot the system and boot into safe mode rather than normal I can get into Windows but there isn't any decent logs so far to go on without some additional work.
Is there something I've missed out ? I've done a quick search but couldn't find any related posts on the forum. I've listed my spec below.
Thanks for any help.
KN8 Diamond
2 x 512MB Dual Channel EL PC-3200 OCZ Platinum Rev2
OCZ Powerstream 600W PSU
Adaptec 29160 Raid Controller
Gainward 6800 Ultra Golden Sample
Creative Audigy 2 ZS Platinum Pro
Hi. I'm just going to start removing/moving hardware and carry out more testing, but I've booted into safe mode and justed the error settings so that I can actually read the error. The Windows stop error is 0x0000009C MACHINE_CHECK_EXCEPTION. I've just completed a MEM86 test and had no errors on the 2 x 512 Sticks.
I'll adjust some of the hardware and if that doesn't make any different the only bits it leaves are the CPU and motherboard.
Thanks again.
Similar Messages
-
Creating a partition after Win server 20i12r2 install
Hi I wish to allocate a separate partition for my my win server 2012r2 (hp proliant gen 6 server.) The win 2012r2 was installed in a hurry without partitioning the HD raid4 … The ADS and home directories of users are in place and I wish to transfer the user
data (home folders) to the New Partition. How do I go about without doing a fresh install. pl helpHi Journville,
Do you mean you have install a server 2012R2 but used up all your current disk and you want to migrate the current user profile data to another partition? It is not support
scenario.
User Profile folder relocation
Folder Redirection is partially supported by OS:
Correct functionality of redirected folder is delegated to third party applications and could generate problem after OS installation
The Directory Database can be moved to others partition, you can refer the following related KB:
Move the Directory Database and Log Files to a Local Drive
http://technet.microsoft.com/en-us/library/cc816720(v=ws.10).aspx
I’m glad to be of help to you!
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place. -
HTTP 500 ERROR AFTER EXCHANGE 2013 SP1 INSTALL
Help after exchange 2013 sp1 new install unable to get to the ECP or OWA page with HTTP 500 error in IE the install went ok but not sure what can be causing the error any help would be appriciated.
EXCHANGE 2013--SP1 on WIN2K12--R2 Standard
TY
M4326See the following:
http://social.technet.microsoft.com/Forums/exchange/en-US/08d3777c-dc03-4411-8c87-7db37d2f406a/exchange-2013-owa-login-error-http-500?forum=exchangesvrclients
CK -
A22m and A21m will not install/recognize internal Ethernet card after WIN XP clean install
Hello,
I have few of A22m's and A21m and a few weeks back I did clean install WIN XP SP2. All is good with the exception of Ethernet card - which is not recognized after the installation. Previously those systems were running XP SP1 and there were no issues with the Ethernet card.
I have tried all possible driver downloads from Lenovo/IBM support site including Intel and 3com and still nothing. Supposedly the Ethernet drivers are native to win XP, but for some reason I can't get them to work.
I want to donate these units to charity, but I want to make sure all works fine.
Thanks in advance,
AndrzejWelcome to the forum!
Please post the 7-character model number(s) of your A2x ThinkPads (should be something like 262x-xxx), so we can determine the type of mini-PCI card installed.
Also, after downloading the drivers, have you unpacked them from the appropriate directory, should be something like C>Drivers>Win>Ethernet.
Good luck and let us know.
Cheers,
George
In daily use: R60F, R500F, T61, T410
Collecting dust: T60
Enjoying retirement: A31p, T42p,
Non-ThinkPads: Panasonic CF-31 & CF-52, HP 8760W
Starting Thursday, 08/14/2014 I'll be away from the forums until further notice. Please do NOT send private messages since I won't be able to read them. Thank you. -
Print Spooler does not work after Win 8.1 install
I upgraded several computers to Win 8.1. Most are operating normally and do not have this problem. This is relevant to show that it is not a printer hardware or compatibility problem. On one computer, the print function is not working.
I've tried reinstalling printers, getting new drivers, etc. It comes down to this. An active (connected) printer is selected and print test page is selected. The dialog box says that the print queue is full. I went to the queue subdirectory
and deleted all files, no change to the results. The Print spooler is active in task manager. Stopping and restarting the print spooler makes no difference. Any ideas?I had similar problems with HP Printers on the LAN (after upgrade from Windows 8 tot 8.1
32bit)
HP Laserjet 4000 Laserjet 4050 and Laserjet 4250 - all with Network interface.
Erratic behaviour: inserting blank pages, no duplex printing, programs stalling when printing etc…
Printers and network are fully functional and work perfectly with W7 and XP. Not with Windows 8.1.
Strange thing: Epson Aculaser and Ricoh Aficio 3224 worked fine but those were installed after the Windows update.
So definitely something with the Microsoft drivers for the HP Laserjet printers.
After a few installs and uninstalls of the HP printer drivers the problems stayed.
Then I removed all HP related driver files (C:\\Windows\\system32\\spool\\PRINTERS")
and all references in the Register because the standard uninstall of the drivers did not remove all files.
-> First uninstall ALL HP printers (laserjet, deskjet, officejet etc ..)
-> Then look in
[HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Print\Monitors]
[HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Print\Environments\Windows NT x86\Drivers]
[HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Print\Environments\Windows NT x86\Print Processors]
[HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Print\Printers]
Make a backup of the registry keys and then remove all files starting with hp….
Remove the print processors starting with hp
(i.e. hpzpplhn.exe)
Then restart your system.
Reinstall the printers, they should be OK now.
If you still have duplex printing problems : replace the hpzpplhm print processor with the winprint processor. (may give other limitations, google for more info).
In my case this solved the erratic printing problems. -
SD card reader doesn't work on Satellite C850-1CN after Win 8.1 install
Hi,
Since I installed Windows 8.1 on my computer Satellite C850-1CN ref. : PSKCAE my SD port does not work
I would like to know if there is a driver I need to download because I searched the site for a pilot port but in vain ...
Sorry for my English I speak French and I hope I'm in the right forumHi
You have to download and install the card reader controller driver for Win 8.1 system
This driver should be the right one:
[Card Reader Controller v 6.1.8400.30136 Windows 8.1 - 64 Bit|http://www.toshiba.eu/innovation/download_driver_details.jsp?service=EU&selCategory =2&selFamily=2&selSeries=312&selProduct=7499&selSh ortMod=3417&language=13&selOS=all&selType=316&year upload=&monthupload=&dayupload=&useDate=null&mode= allMachines&search=&action=search&macId=&country=a ll&selectedLanguage=13&type=316&page=1&ID=88526&OS ID=46&driverLanguage=42] -
K8N Diamond reboots after shutdown :censored:?
I hope others are experiencing this too, I'd hate to be alone! Almost everytime I shutdown my PC after about 3-5 seconds it reboots by itself. Is this a known prolbem?
amt, I have a Neo4 Plat which is a different board but had a similar experience after I installed my Opty 165 but was also dealing with SATA II problems and it puzzeled my on what was going on. I had a problem with bios not recognizing the Opty which I fixed with a MurdocK modded bios and got firmware upgraded on Seagate SATA II- then end result was that it went away during this process but it is still a mystery Hope you can figure yours out. I had to hold power button down for a couple of extra seconds after it shut down or it would magicly spring back to life.
-
X1 Carbon restore after Win 8 clean install
I've tried to boot to the F11 recovery, but the system will not boot to the recovery partition - and it is there. Is it possible to still boot to that partition and recover the original Windows OS or will I need to get recovery media some other way?
ThanksCalled Lenovo about it and they sent the recovery media.
-
After win xp install?????
what do i do after win xp is installed...i reboot and it stays in win xp...i want to boot into osx...any help much appreciated!!! thanks in advance!!
this is a new macbook 1.8 ...it is for work...i installed a brand new win xp system earlier today... the mac os was all up to date, was done via software update....the moment you see the gray screen hold down the option key and it will bring up mac osx or windows
-
EventID 2001 after SP1 install
Hi.
After upgrading to SP1 for Exchange 2013, I keep getting this error:
Event 2001, MSExchange RPC Over HTTP Autoconfig
A transient failure has occurred. The problem may resolve itself in a while. The service will retry in 00:00:15. Message:
Filename:
Error: Cannot add duplicate collection entry of type 'add' with unique key attribute 'path' set to 'C:\Windows\System32\RpcProxy\RpcProxy.dll'
'It does not seem to be causing any problems, but it is annoying to have this error log every 15 seconds.
Unfortunately I do not know anything about IIS, but it seems to be where problems is.
Anybody know how to fix this?
Regards
Jens HyllegaardI had this error on my new exchange 2013 install for a client.
After migrating a number of users over and testing OWA (send & receive) i assumed all was well, one of the batches had finished so i asked the user to open up outlook, but it was throwing up U/N & P/W box, even with typing in the correct details
it was not accepting anything, then not being able to connect.
After a lot of hours troubleshooting this issue (Exchange 2013 is new to me!) i found that the RPC to HTTPS feature was not installed (this is required for outlook anywhere to
run, which connects outlook to exchange 2013). After finding this i installed this feature and thought job done.
Logged back onto the users machine and still had the same error, after more troubleshooting i found this event ID in my exchange log's. Every 15 seconds this was popping up, so after removing the RPC to HTTPS feature, rebooting the server and re-installing
this has cured the issue for me!
Thought i would post up to prevent anyone else spending there evening looking through exchange 2013 logs!
Regards
Mike -
Problem installing spotify win 7 sp1 x 86
hi, my problem is a computer Hp win 7 sp1 x 86, when i tried to install (double clic over installer) notingh happend, no screen of the installer or some screen that show me that the instaler is working my question is if i need a update or a dll for the correct installation, i tried install a very old version of spotify(0.9.2) and was installed succesfully so i think some program or sistem update specific is needed thanks for you time and hope you guys can help me with this...
Moderator,
thank you for taking the time to edit the link to open in a new window, to a site that takes me to a site with a possible solution. In reading that 'solution', I see comments at that page, that state that solution might not have the desired result.
Any Chance Lenovo can provide a Solution to this issue that I also see occur on any Windows 7 64 bit system in my environment? I RDP to the system, and launch ThinkVantage System Update 4.03 freshly downloaded from:
http://support.lenovo.com/en_US/downloads/detail.page?DocID=DS012808
I see the splash screen for a few seconds, then it disappears...
The only means to get ThinkVantage System Update 4.03 to run on the remote system I am working on, is to terminate my RDP session, and resort to a VNC or Logmein remote session to the remote system, and run ThinkVantage System Update 4.03 that way.
WHEN IS THIS GOING TO BE FIXED?
A great application... sad that it STILL will not run in a RDP session.
Stephen -
CC wouldn't install on my Win 7 SP1 i5 dell. Why?
It's okay on my i7 laptop running the same Win 7 SP1 home edition. Don't understand what the problem is.
what do you see when trying to install?
-
K8n diamond plus no audio after connecting Avermedia/Hauppauge tv card
k8n diamond plus
Avermedia mce m1a2 tv dual tuner
windows xp mce
after connecting the tv tuner card there is no more audio at the speaker output.
(the same problem occurs with a Hauppauge tv pvr 500)
the headphone output is still working.
is there someone who knows how to solve this problem ??Found it here ! it works
http://forumz.tomshardware.com/hardware/k8N-Diamand-Sound-ftopict183919.html -
This is what I've got installed on the K8N Diamond Plus:
AMD x2 4400+ @ 2.75 GHz
4 GB DDR 500 GigaRAM
2x EVGA GeForce 7800GT's in SLi
Sound Blaster XFi Fatality Edition
2x 74 GB WDC Raptors (non-RAID)
2x 320 GB WDC SATA Raid Drives (RAID-0 on Sil3132 chipset)
Sony DRU 810 DVD Recorder
Sony CRX 320 Combo Drive
WinXP Pro 32-Bit SP2 installed (WinXP Pro 64-Bit this weekend)
Windows installed A-O-K, drivers no prob, but, I ran into two snags. One, in my system properties a "PCI Modem" shows up looking for a driver. Second, I have a Koutech Firewire 800 / USB 2.0 PCI-e card that picks up when it wants to. That card has been removed physically and I'm planning on RMA'ing the Combo card...so far. Has anyone seen a phantom modem card? I'm really hoping and praying that it's not the motherboard that's defective.
The only other minor issue is that my memory in the BIOS detects as DDR 333 at 2.6v. GigaRAM recommends 2.9-3.1v, but I cannot adjust the voltage in the BIOS. Is there a physical way thru the BIOS (without voiding the warranty) or only way I'll be able to thru software??? Prefer not to. Any help on the issues mentioned will be appreciated.
Latin Polar BearI see that few people have come and gone past this topic. Can anyone help or does anyone have any insight???
LPB -
R400/T400/T500/W500 - Win 7 SP1 not installing
Hi Commuity
I searched the existing posts and could not find a similar issue or answer,
I have two G560 Lenovo laptops with the original Win7 Home Premium installed and both cannot update to SP1. I have tried to install SP1 using Microsoft Update and using the file downloaded from the Microsoft support site (all 1.9Gb). Niether managed to complete the update to SP1. The main issue apart from missing security in SP1 is that I can't get a later version of Internet Explorer.
Windows Update says the system is up to date, but then Window explorer will not update as SP1 is not installed.
Can anyone advise how I can get Win7 to update to SP1 and beyond? Much appreciate your support.
Should I follow the advice at http://windows.microsoft.com/en-us/windows7/troubleshoot-problems-installing-service-pack ?@glenn578...
Have you had a chance to try Hoov's suggestion? If so, were you successful at getting SP1 installed?
Regards.
English Community Deutsche Community Comunidad en Español Русскоязычное Сообщество
Community Resources: Participation Rules • Images in posts • Search (Advanced) • Private Messaging
PM requests for individual support are not answered. If a post solves your issue, please mark it so.
X1C3 Helix X220 X301 X200T T61p T60p Y3P • T520 T420 T510 T400 R400 T61 Y2P Y13
I am not a Lenovo employee.
Maybe you are looking for
-
How do I do this
-
How to convert Report Model to Report Designer DataSet
To all, I have a two part question. One is I am experiencing the error at the end of this question when migrating SQL Server 2005 SSRS Native Reports, the report uses a Report Model, to SQL Server 2008 SSRS Native. I bring the Report and Report Model
-
Retina Display MacBook Pro image persistence problem.
Hello, I have recently ( about 3 months ago) bought a Retina MacBook Pro and installed Windows via Bootcamp on it. I unfortunately am used to Windows. Well recently I tried to migrate to OS X and use it more often. Whilst doing so something caught my
-
the keyboard shortcut that turns an exclamation mark into an apostrophe no longer works in iOS 6. How can I restore that shortcut?
-
Trade in value of MacBook Pro 2009 2.26Ghz
i have a late 2009 macbook pro model with 2.26 ghz core 2 duo 160 gb hard drive and 2 gb ram i am wondering what price it would be worth now as i am finding things painfully slow. and also anyways of speeding it up. also answers in australian currenc