K8N Diamond Plus' Audio drivers 4 Vista RC1???

Guys i need to find drivers for RC1 Vista for my built in Mother board creative Audigy SE on K8N Diamond Plus. Can any one help me where to find these drivers????????

well i installed the vista RC1 and downloaded the Audigy Se's vista RC1 drivers from creative's web site and i installed it on my system and it detected my motherboard's audigy SE as audigy live 24 bit but there was no sound so i updated the driver and i gave the path of my window's xp driver and it worked for windows vista RC1. and my sound card is now dectected as audigy SE not live 24 bit. thanks to msi for making a driver which works with both xp and vista RC1. i ll try to install the Xp's driver directly on Vista with setup.exe, and will see if this will give me all the sound configrations which we do see in windows xp. But i still request MSi to provide us good vista drivers.
I have one question,
CAN WE INSTALL AUDIGY SE's DRIVERS DOWNLOADED FROM WWW.CREATIVE.COM FOR AUDIGY SE BUILT IN SOUND CARD OF DIAMOND PLUS MOTHERBOARD(FOR WINDOWS XP) ?

Similar Messages

K8N Diamond Plus Audio Problem

New rig - have the K8N Diamond Plus, AMD 64 X2 4400+, Logictechz5300-e speakers. When testing audio - the front speaker channel does not work - the center and rear are fine - tested to make sure it wasn't the speakers - definitely a mobo problem. Have tried it set to 5.1, 6 and 8 channels. Has anyone else experienced this issue??
Thx

The audio signal from DVD or CD is passingthrough IDE CABLE digital..(When listen CD audio).Now with X-FI you must buy(of corse if you have the money) 7.1 audio speakers like mine(gigaworks s750) to take full advance of your card.Believe me you won't regret it!.
http://images.europe.creative.com/iss/images/artwork/a6_rgb/GigaWorks_S750_c.jpg
http://images.europe.creative.com/iss/images/artwork/a6_rgb/DDTS_100_c.jpg

K8N Diamond Plus audio out problem

Hi,
I'm having an issue with the audio out on my K8N Diamond Plus. The rear audio out works fine when left jumpered. However when I connect the front panel audio connector to the mother board the volume of the rear audio out drops to an almost in audable level while the front panel audio works as expected.
At first I thought the rear audio had been completely disabled until I tried turning my speakers all the way up.
Is there a software issue here?
FYI I'm trying to use the front pannel audio connection on a Silverstone TJ07 case.

hey - mikein_texas here - i have same board but with a Centurion case -
couple of things i ran into - maybe will spark some ideas
initally i hooked up front panel audio and got nothing
then i read on page 2-19 of manual that 5-6,9-20 have to be jumpered for rear audio to work
but that means no front audio which was a drag - but solved that prob with usb mike and headphones
apparently unless i am reading it wrong and someone please correct me if so, but you can have front audio OR rear audio
BUT not both
again look at page 2-19 in manual and specifically at text in grey box in middle of page
Yukon PXE 2.01 ( 20040406 )
Pre-boot Execution Environment PXE v.2.1
DLink Cable Modem - model DCM-202
ViewSonic VX2025WM 20.1" Widescreen TFT LCD - 1680x1050, 800:1, 8ms
MSI K8N Diamond Plus Socket 939 NVIDIA nForce4 SLI X16 ATX AMD
SAMSUNG Black 1.44MB 3.5" Internal Floppy Drive Model SFD321B/LBL1
SONY Black IDE DVD-ROM Drive Model DDU1615/B2s
XFX Geforce 7600GT PV-T73G-UDD3 Video Card
SAMSUNG 16X DVD±R DVD Burner - 5X DVD-RAM Write and LightScribe Black ATA/ATAPI Model SH-S162L/BEBN
COOLER MASTER Centurion 532 RC-532-SKN1 Black Computer Case
AMD Opteron 165 Denmark 1000MHz HT 2 x 1MB L2 Cache Socket 939 Dual Core
CORSAIR XMS 2GB (2 x 1GB) 184-Pin DDR SDRAM Unbuffered DDR 400
Seagate Barracuda 7200.9 ST3808110AS 80GB 7200 RPM 8MB Cache SATA 3.0Gb/s Hard Drive
Ultra ULT31849 X-Finity 600W Power Supply
Cooler Master A12025-12CB-5BN-L1- 120 x 120 x 25mm 1200rpm, 43cfm, 22dBA, LED, 3-pin - front intake case fan
Scythe S-FLEX SFF21F 1,600rpm, 49.0CFM, 20.1dBA, 3-pin, 120mm S-FDB Bearing - rear exhaust case fan

K8N Diamond Plus temp monitor w/Vista 64-bit

Well this is my first time ever posting for help like this but I've searched to the ends of the net with no results. What I have is a need for a hardware/mobo monitor that will work with both the K8N D.P.(MS-7220) and Vista 64-bit Ed. None of the MSI related applications (Core Center, etc.) work and for some reason Speedfan v4.3 wont work either. I can install it but it will not show anything more than CPU and RAM usage. Does anyone know of a program that is compatible with this board AND Vista 64???
The reason for the importance is I flashed my BIOS prior to upgrading to Vista... I forgot to write down my BIOS settings from when I built/slightly OC'd the machine. Now I have to start all over again but nothing seems to work on this configuration other than Prime95... so I cant change anything while Windows is running (not really a big deal, just takes longer) but worst of all I cant monitor my temp... even now.
Thanks in advance for any help.

Thanks Hans...
But with Vista having been on the scene for quite a while now (beta wise) there is an overwhelming supply of compatible programs out there... the problem lies more with this board than VISTA. I have found there is VERY little support for this board... which was actually in short supply upon its release. Even on MSI's site there is Vista support for many of the drivers and applications with other NForce4 boards.
This is why I brought my question here. Just hoping an MSI guru around here might have a clue as to a program that'll work with this board or if MSI is planning on updating Core Center to work with Vista anytime soon.
I have controlled the fans in the BIOS, I just need to know the temps DURING torture tests and not after a reboot.

I WANT DRIVERS FOR MY K8N Diamond Plus

I WANT DRIVERS FOR MY K8N Diamond Plus MAINBORD FOR WINDOWS 7 HELP ME OUT

Which do you need, that aren't supplied by Windows 7 itself?
Vista drivers may work if something refuses to work without special drivers:
http://www.msi.com/index.php?func=downloaddetail&type=driver&maincat_no=1&prod_no=232

K8N Diamond Plus + Vista upgrade issues + Memory

When I go to install Vista Business , I receive an error before the install saying that my motherboard is Non-ACPI compliant. I went into the bios and and made sure that all ACPI settings were turned on. Also I installed 2 more gigs about a month ago and only see 3 gigs on post instead of the 4 that is installed. I tried to update my BIOS using the MSI utility but received a memory error saying it can detect the correct amount. I ran MEMtest and it passed .Here are my system specs:
K8n Diamond Plus - Bios ver 1.0
AMD Ath 64 x2 4800 toledo
4 gigs of Corsair XMS DDR433 3500LLPRO
2 x EVGA 7950 GT KO Superclocked 512mb
WD Raptor 74 ( OS)
WD SE16 320 gb (storage)
Plextor 18x
PC Power and Cooling Turbo Cool 510 SLI
XP SP2

Quote from: iampiglet on 02-February-07, 23:18:28
When I go to install Vista Business , I receive an error before the install saying that my motherboard is Non-ACPI compliant. I went into the bios and and made sure that all ACPI settings were turned on. Also I installed 2 more gigs about a month ago and only see 3 gigs on post instead of the 4 that is installed. I tried to update my BIOS using the MSI utility but received a memory error saying it can detect the correct amount. I ran MEMtest and it passed .Here are my system specs:
K8n Diamond Plus - Bios ver 1.0
AMD Ath 64 x2 4800 toledo
4 gigs of Corsair XMS DDR433 3500LLPRO
2 x EVGA 7950 GT KO Superclocked 512mb
WD Raptor 74 ( OS)
WD SE16 320 gb (storage)
Plextor 18x
PC Power and Cooling Turbo Cool 510 SLI
XP SP2
I have the same motherboard with 4GB Ram. I had to enable the memory hole in the memory configuration of the bios for it to see the full 4GB. However, Windows 32-bit will not show the full 4GB ram since 32-bit addressing limit is 4GB and all your peripherals have to be included like vid card memory, etc. So don't beat your head against your desk once you get your bios seeing the 4GB and Windows 32-bit doesn't. My Vista gives 2.8GB ram of my 4GB, some get more, but I know I have two video cards with 768MB ram also. I'm using 1.2 bios.
Incidently, I ordered an OEM Vista X64, it will be interesting to see if it sees all my memory since 64-bit can go up to enormous addressing ranges.
Good Luck

K8N Diamond Plus SiI 3132 WinXP x64 non-RAID drivers?

Hi
I'm looking for non-RAID drivers for the SiI 3132 on my K8N Diamond Plus for WinXP x64 (I managed to fine the x32 ones and they work fine so I know it's not the drives or the moboard. I tried the drivers on MSI's website.
I've searched around the forum and followed the leads onto planetamd64 and the Asus website for them, but to no avail.
To be precise, I have selected non-RAID in the BIOS, and the drives to show up on on the POST screen, but do not appear in Win 64; there is the classic exclamation mark in the device manager for a 'Mass Storage Device'. I don't want to concatenate the drives in RAID mode, so I did not try booting with that selected in the BIOS lest it destroy the stuff I have on them.
[I miss the simple JBOD option in the 3114...]
Any help gratefully appreciated!
thx
bn

Hi all,
I solved the problem.
You won't find the drivers under the drivers section of SiI's website but you will in the Knowledge Base. Look under Serial ATA | COntrollers | SiI3132, you'll find article 11043 'SATA 64 bit Windows IDE driver - released' dated 8/19/05. Click under that and you'll find a file 3132_win64_idrv_1004_logo.zip. It's what you need.
Hope this helps someone.
bn

K8n diamond plus no audio after connecting Avermedia/Hauppauge tv card

k8n diamond plus
Avermedia mce m1a2 tv dual tuner
windows xp mce
after connecting the tv tuner card there is no more audio at the speaker output.
(the same problem occurs with a Hauppauge tv pvr 500)
the headphone output is still working.
is there someone who knows how to solve this problem ??

Found it here ! it works
http://forumz.tomshardware.com/hardware/k8N-Diamand-Sound-ftopict183919.html

MSI K8N Diamond Plus - Guide to my first week

OK, not a newb here, but been around the block quite a bit. MSI K8N Diamond Plus is my 5th A64 mobo (ECS K8M800, my daily undestroyed computer, K8T800, my 12 year olds gamer, Asus A8V Deluxe, first 939 system, Abit AN8 SLI, first SLI gamer, and now the MSI Diamond Plus). Had the KDP (K8N Diamond Plus) for more than a week now, and here's what I've learned.
This is state of the art again, and we have no one to blame but ourselves for the pain this causes us when we upgrade like lunatics
And as usual, the drivers and BIOS are al Dente (i.e. not cooked enought yet, a little raw)
MSI is also oddly silent on this system, which is wierd, as they are a large company, and specifically cater to enthusiasts. But their BIOS guys are MIA. Hopefully this will not be forever. Asus, ABIT, DFI, Epox are always fast with fixes
The board is a nice design, with everything basically accessible, as much as any other board. Lots of purposeful components, not too many dumb frills. No tooty fruity colors, but rather practical parts.
The new 2 piece NForce chipset is fine, and the MSI guys gave us a decent, but funky cooler. It gets a little warm to the touch when you pound on it with Prime95, or Quake4, but other than that it is fine
The manual has a zillion typos, and fortunately for us in this forum, we have shared what we've learned. The translation from Chinese to English leaves quite a bit to be desired, and hopefully, MSI will learn from Asus and Abit and get a better translation service. In 2006 this is just plain stupid, especially with a $225 board
As usual, the mobo supplied tweaker utilities are just aweful. They look like a hallucination from a Hunter S Thompson book, and they work about as well. Core center is a sad state of affairs, and the rest of them just burrow their way into your otherwise stable system and cause it to have poor behavior. And therefore as usual, the BIOS is the best way, if slowest, to tweak this bundle of parts
Which brings us to the BIOS. IMHO, the worst one I've seen on a high end board. ZERO explanation for half the settings (this is not strange in and of itself, BIOS is still a black art, but in a tweakers board, we should have some basic explanation )
There seem to be adequate settings in the BIOS for all sorts of doodads and gizmos, but who the heck knows what half of them are. Roger points out rightfully, that we now need to "Tune" across all these different intermediary bus structures and test. But with the lack of info from either NVidia, MSI or anyone else for that matter, its kinda hard to know where to start.
The board is clearly sensitive, which is a result of it being high strung. This is no different than any "first out" product I've ever bought. Most take 2 or 3 turns of the crank to get totally stable and forgiving. This one hated my OCZ platinum EL 2Gb kit memory, and it brought out the worst in one of the SLI based EVGA 7800 GT COs. These components worked in the Abit AN8 SLI (although not always great), but the MSI has ZERO tolerance for even the slightest pertubation from the memory. It was BSOD city until I removed both of these components by process of elimination that took probably 100 hours
Once I removed the bad components, and replaced the memory with Geil Ultra X 2x512 2-2-2-5, it worked great, ran Prime95 for 10 hours with no errors, and seems reasonably stable. I've RMA-d the bad 7800GT CO back to EVGA, and will report back on how SLI behaves when I get the new one (cross shipped of course, I haveno patience )
I also now need to replace the 2Gb RAM kit with something that the board will tolerate. I may RMA the 2Gb kit back to OCZ and try another one, but I dunno. I love OCZ but I have a bad feeling about this, even though they have great!!! support. I may try OCZ PC4000 or the RAM that Roger successfully used.
I did upgrade to the 1.16 BIOS, and found that some new things were added, as well as voltage control in Cell was a little better, but registration of changes in voltage is still a disaster. I adjusted a bunch of times, it didn't register, and I ended up smoking a new A64 3700+ Diego with 1.95 volts, even though the BIOS claimed it was 1.53. I had to rebot to see what was going on. The Thermalright XP-90 kept the proc from melting down through the earth
Finally, I hope this board attracts more people, and therefore more tweakers that can figure out all these gadgets and settings. Everyone flocked to the Asus X16 SLI product, which is too bad, as this one needs lots o' folks to hack it up for us to figure out what is going on.
The on board Creative audio sounds lousy to my ears, and I will replace it with an Audigy 2ZS gamer that I had in the Abit. It just sounds better, but hopefully the drivers will not trash my newly stable system. Creative scares me, they scare me alot.
I've been able to get the CPU up to 2.4Ghz, with a .5 volt bump to the CPU and 2.9 volts into the Geil memory. So far, so stable, no smoke coming out yet
I hope this info is somewhat valuable to someone on this board. I will post details of all changes that I make, as others are doing, so we can at least take care of ourselves with this thing.

Quote from: nanohead on 15-February-06, 01:17:10
Which brings us to the BIOS. IMHO, the worst one I've seen on a high end board. ZERO explanation for half the settings (this is not strange in and of itself, BIOS is still a black art, but in a tweakers board, we should have some basic explanation )
There seem to be adequate settings in the BIOS for all sorts of doodads and gizmos, but who the heck knows what half of them are. Roger points out rightfully, that we now need to "Tune" across all these different intermediary bus structures and test. But with the lack of info from either NVidia, MSI or anyone else for that matter, its kinda hard to know where to start.
first of all, i do think that all the settings in the BIOS have an explanation in the manual, even if it's a basic one. if that explanation doesn't tell you everything in detail, is because if you do need a detailed explanation of the settings, you probably shouldn't be messing around with those settings.
Quote from: nanohead on 15-February-06, 01:17:10
I did upgrade to the 1.16 BIOS, and found that some new things were added, as well as voltage control in Cell was a little better, but registration of changes in voltage is still a disaster. I adjusted a bunch of times, it didn't register, and I ended up smoking a new A64 3700+ Diego with 1.95 volts, even though the BIOS claimed it was 1.53. I had to rebot to see what was going on. The Thermalright XP-90 kept the proc from melting down through the earth.
wanna tell me how did you get 1.95V on that mobo?
Quote from: nanohead on 15-February-06, 01:17:10
I've been able to get the CPU up to 2.4Ghz, with a .5 volt bump to the CPU and 2.9 volts into the Geil memory. So far, so stable, no smoke coming out yet
a 0.5V bump? again, you must be joking. maybe 0.05V.

K8N Diamond Plus, Line-In & AVerMedia Studio .103

Hello,
I got K8N Diamond Plus and AVerMedia Studio .103 audio out connected to my onboard sound device's (Audigy) Line-in. I don't know how to describe the situation but I'll try. The problem is that the captured audio is some kind of wavey like an old "record", the sound is cry-like especially when there's a music in the background.
It is really annoying to have such a problem with this kind of expensive product. I'm sure it's not TV Card related because I use it for 5 years now with the same OS, Application, Drivers and cable. The day I upgraded my system I met this trouble. I've searched for driver updates, chipset updates related to this issue but couldn't find any. I tried every possible option/configuration with the sound card and no hope.
I think it is because that the line-in is also used as an output with the 4 speaker configuration. Every passed day with this issue I add spoilt videos to my archive and this upsets me.
Thanks for your help and concerns
Yours respectfully
M. Erke Tiryakioglu

Quote from: syar2003 on 30-April-06, 17:46:53
The line-in only has dual fuction in 8 speaker sw config (7+1) .
With 5.1 and lower the numbered jack #1 is only having line-in config.
Make sure you have correct Multi-Channel Audio Function mode properly selected in the software
utility for your speaker connections/configurations.
And use the Creative web update to have the laterst drivers and software .
First of all thanks to all of you guys...
Secondly, I was just trying to point out that may be the dual-function support (doesn't matter when) is doing this...
And yes I am using windows XP as it says in my signature, but thats not an issue since i used this card (AverMedia) with XP pro for four years with no problem.... I can't say anything about the dual-core tho...
BTW I tried to manually update the audigy from creative's web site, but couldn't be sure if I had to download the Audigy drivers or should I use MSI's web site for my sound device, since it's on board? Or is there a version in the Creative web site to, or even the audigy drivers itself may be? Do you have any suggestions? MSI doesn't have an update tho I know that..

K8N Diamond plus!!! Help onboard sound

Hello, I have seem many posts about the onboard sound blaster and this board. I have a slightly different story.
I am one of the many who have VERY low volume on my onboard sound blaster audio. I read about needing a -5V rail and some other posts, but i decided to just buy a PCI version of the card instead. Well i plugged the card in, Removed the old audio drivers and installed the PCI sound blaster card...and guess what, I STILL HAVE LOW VOLUME!!!!! WHat does this mean? Is the power supply screwing with both audio devices? Is it the motherboard??? DRIVERS?? HELP!!!
I upgraded my bios using the latest version in LIVE update and all drivers are updated with live update.
I have NO front audio hooked up and i tried new jumpers on the audio pins with no help.
ALSO... whenever i plug in my Plantronic USB headset....the system will use them one time and never again unless i system restore!!
K8N diamond PLUS!
ENERMAX Liberty ELT500AWT ATX12V 500W Power Supply - Retail
AMD Athlon 64 3700+ San Diego 2000MHz HT Socket 939 Processor Model ADA3700BNBOX - Retail
Western Digital Caviar SE WD1600JS 160GB 7200 RPM SATA 3.0Gb/s Hard Drive - OEM

ALL sliders are all the way up and digital audio OUT is not selected.
The odd thing is that the sound had worked before. I built the computer for a friend, and when we fired it up for him...nothing

K8N Diamond Plus microphone not working

Hello All...
Thanks to everybody who helped me with my cpu power problem - the computer is up and running wonderfully now. The only issue that I'm experiencing, and I'm fully prepared to accept user error, is the fact that my mic is not working, or the levels are EXTREMELY low. I have an antec case, and I used the pin header on the motherboard for front panel audio which contains a mic input and a line out (For me, it's for headset convenience without having to remove my speaker wire). Since both the pin header and the connector conform to Intel standards, I think that's not the problem. I've used the drivers on the CD as well as the drivers on the Creative site for Soundblaster Live 24 bit. Both the front and rear connectors (and either version of the driver, for that matter) yield very low volume from the microphone. I *could* suspect the headset, but it's fairly new and worked yesterday, and also, the earphone portion seems to work correctly.
Since you'll want my specs:
K8N Diamond Plus
Antec "Piano" case with 450 watt antec smart power supply
Geforce 7800GTX
dual pata drives (striping)
dual dvd rw drives
dlink wireless lan
Let me know if I can provide any other info, and thanks in advance for any assistance
Steve

Didn't seem to make any difference. I jumpered the pin header so that it was back to the way I got it out of the box. I even used a microphone for our camcorder, and that didn't seem to get any better result either. Very strange...........

CPU Usage 100%? K8N Diamond Plus

Never before have I witnessed the CPU being used at it's absolute maximum. It has been occuring regularily with my system. I noticed it first when my screen saver started getting jittery. This seems to occur most often about 1-2 minutes after windows finishes loading. It seems kind of odd to me that this occurs during typically idle system times. The memory usage also dramatically rises during these spikes, using ctrl+alt+delete I noticed svchost.exe to be the culprit of the memory usage atleast. The hard drive doesn't appear to be active when these events occur. Is this normal for this motherboard, or is this something that should be corrected?
I've always had 3 short beeps upon startup with this board, but it has never stalled the boot process. Anyone know what this means?
I've upgraded my board somewhat recently and carried over the CPU and memory from a older MSI model that used the same type. Could it be possible either or both are incompatible?
Also one, somewhat less important problem. First off I must say that the PS/2 power on feature is pretty cool. I used it with a wireless keyboard so I could turn on my PC from my living room HDTV (I have my comp wired through Y/Pr/Pb cables). Only problem is about one in every 4 or so shutdowns the system restarts immediatly when this feature is selected in the bios. Bios issue maybe?
System Info (and everything directly connected to it):
(pretty sure not all of this is relevant, but I figure it couldn't hurt)
MoBo: MSI K8N Diamond Plus
Memory: 1Gb (2x512 kit) Crucial PC3200 CT6464Z40B.C8TD (in slots 1 & 2)
Processor: Athlon 64 3200+ Winchester
GPU (only one): MSI NX7900GT-VT2D256E-HD (primary PCI-e)
Modem: SupraMax LE 56K Fax Modem (PCI)
HDD: WD Caviar 120Gb IDE (primary)
HDD: Maxtor 80Gb USB (external, non system)
3.5: Standard 3.5" floppy drive (a:)
5.25: Lite-on 48x CD burner (secondary slave)
5.25: Sony DVD rom (secondary master)
PS: Antec SmartPower 2.0 500W
Human Interface: Wired Logitech KB & Mouse through USB (for primary use)
Human Interface: Wireless Logitech KB & Mouse through PS/2 (for remote use, often turned off)
Primary Monitor: Viewsonic P70f 17" CRT hooked to DVI #1 via RGB adapter
Secondary Monitor: Sony KDL-V32XBR1 32" HDTV through 1080i Y/Pr/Pb adapter, stereo audio
Speakers: harman/kardon
Connected to internet via Cat5 network, phone modem sometimes used when primary internet is down
OS: Windows XP Pro w/ SP 2 installed
Thank's in advance to anyone that can help me as I'm pretty much stumped at this point.

Quote from: mdawgmike on 11-November-06, 11:25:18
Any other suggestions?
how about this:
Quote from: BOSSKILLER on 03-November-06, 23:14:30
get Process Explorer to determinate in details what make this CPU usage: http://www.sysinternals.com/Utilities/ProcessExplorer.html
it has more detailed information than the built-in task manager.

K8N DIamond Plus- 4 sticks of memory problem

I have a new Opteron 180 with a K8N Diamond plus mb. I am thinking about getting another 2g of memory to run with my current 2g of 3200 memory to speed up Vista even more. I thought the new chips could run 4 sticks of memory at 400 with a command rate of 2t. I wanted to try to see if it would work so I pulled two 512 pc3200 sticks from my wifes computer and installed it. At boot up it clocked the memory to 333 (which I expected it to actually) and I got into the bios and set it to 400 with 2t command rate and everything else at default settings. All the memory is Kingston value ram. The computer randomly booted and I had lockups at 400, but at 333 it ran fine, but I still couldn't run the memory at 1t with 333. I am using bios 1.33 as the other bios's always set the HT bus wrong for me. Is this just a function of the motherboard or is the memory not compatable with each other? I thought the motherboard is irrevelant since the memory controller is on the cpu?
Thanks for your help,
Scott

The memorycontroller IS inside the CPU.
And some are lucky to get it stable booting at DDR400 with 4 sticks, some get crashes.
However, most have drop-backs to DDR333.
It's a CPU limitation when using unbuffered memory.
Buffered memory should be able to do it, however, I'm not quite sure as this is an S939 type CPU.
You could try something if you know somebody that has buffered memory.
Sometimes it helps if you lower the other timings.

Soundblaster Audigy on MSI K8N Diamond Plus, Sound Linked? vs Audigy2 ZS?

Had a couple of quick questions regarding the Soundblaster Audigy onboard chip on my MSI K8N Diamond Plus. I have the audio connected to a front panel, and when I try and change the Right or Left speaker volume balance in Windows (by going to volume control and dragging the balance slider right or left), the volume slider goes down and the balance slider snaps back to center. As in my previous post, I had some damage to my front panel connector pins and wanted to make sure this wasn't a hardware issue requiring a replacement of the board.
Also, I have a Soundblaster Audigy2 ZS card from my previous system, and I was wondering if it added anything the onboard Soundblaster chip doesn't provide. I was thinking of installing it, but if the onboard audio does everything the card would, I'd rather just use the onboard solution.
Thanks.

Quote from: syar2003 on 21-August-06, 06:59:38
Onboard creative is just live24 marketed as Audigy SE
live 24bit is an audigy SE striped down of some features.

K8N Diamond Plus' Audio drivers 4 Vista RC1???

Similar Messages

Maybe you are looking for