K8N Diamond Plus - Cool'n'Quite - Not Starting At Full Speed Everytime. Why?

Hello,
I have a K8N Diamond Plus with a power supply that is 620W switching. +3.3V 25A, +5V 30A, +12V 18A, +12V 30A, nvidia 7900GT, amd x2 4400+. My computer will not start at full speed everytime if i enable cool'n'quite. If i disable cool'n'quite, of course, it will start at full speed. I have run multiple benchmarks, etc. using cool'n'quite at full speed and have never had any problems whatsoever. Using BIOS 1.1.
Can anyone suggest an answer, to get the computer to boot up everytime at full speed using cool'n'quite?
Thanks!

you don't need CoreCenter for Cool'n'Quiet to work
install the AMD64 Processor Driver from here:
http://www.amd.com/us-en/Processors/TechnicalResources/0,,30_182_871_9706,00.html
reboot your PC, ensuring Cool'n'Quiet is enabled in BIOS and CPU Multiplier is set to [Auto]
To enable the Cool ‘n’ Quiet feature on a Windows XP system, you have to change the power scheme. Open the ‘Power Options’ from the Control Panel. Choose the power scheme ‘Minimal Power Management’ and click ‘OK’ to enable Cool ‘n’ Quiet.
On a Windows 2000 or Windows ME system, an AMD Cool ‘n’ Quiet tab will appear under Power Options when the Cool ‘n’ Quiet software for Windows 2000 and Windows ME is installed. This must be set to “Automatic Mode” for Cool ‘n’ Quiet to be enabled.
AMD Cool'n'Quiet Installation Guide (.PDF, 653kb)

Similar Messages

K8N Diamond Plus IDE Disk Does not recover after standby or hibernate

Ok this is wierd after i suspend or hibernate windows does not see my IDE disk anymore. I am running bios 1.10. Note ide cd and dvd drives dont seem to be a problem.

z3razerviper,
Have had any problems with the drive at startup not being detected?
Check the system log for the type error you are getting for the failure?
As all the other drives in your system SATA, the Western Digital older system, has a lot of hours on it?
Roger
When submitting a problem, include a complete list of your system components; include part numbers, all Power Supply Voltages, and their output ratings. It is almost impossible to estimate what your problem is without knowing something about it.

Which PSU for MSI K8N Diamond Plus?

I am so frustrated ... I have spent over 6 hours trying to find out which power supplies I can use with the MSI K8N Diamond Plus.
I am not able to find any PSU that has 24 pin, 8 pin and 4 pin power connectors ... do you have to get them custom made or something? I am in Switzerland and it is hard to track these things down if you do not speak the language.
This is the page which I am using to try and find a compatible PSU:
http://www.stegcomputer.ch/browse.asp?cat=376
I think the Spire Rocketeer VI should work but am not sure.
Can anybody recommend a PSU that is compatible with this board? Please.

Quote from: russellmrgn on 27-March-06, 20:51:26
Off topic.
Kenito443,
I see you have the Stacker830, was looking at that case myself. How do you find it performance / quality wise?
Russell
Yeah i love it...the cooling is amazing, my case never goes above 30C and the cpu idles at 22c and never goes over 27C even when OC'd,.. granted i have substantial cooling for the cpu. the case is completely tool less and boasts a up to 9 12cm fans...the case is double encased Al so with a silent PSU (true 500W), which is my set up , it is extremely quiet. i was going to get the lian li until i saw both of them on display. the lian li seemed a little harder to set up for water cooling -if i wanted that option in the future, and the tool less feature for the cm stacker was a lot more appealing. Interestingly, it has its own proprietary hard drive noise reduction and cooling doohickey. Also, the mb has this cool pull out tray plus the PSU rail is really easy to accomadate for a larger PSU. the store where i bought it from in santa clara CA threw in some of these nice dust filters with the case and I was sold. the only con was the price, i paid around $230, which is a little expensive for a CM....oh and a word of warning , the case doesnt really look that big in pictures, but it is HUGE !! it has 10 5.25-inch bays..you can fit every single imaginable peripheral and still have room to fit your kitchen sink..i was definitely surprised to see how big it was in person.

3 ea MSI K8N Diamond Plus will not POST

I have 3 K8N Diamond Plus motherboards that recently started having intermittent problems POSTing to BIOS. I initially found it possible to boot by clearing CMOS and reentering my settings; however, over time these boards have gotten to where they will not POST at all. Power comes up, but the four-LED diagnostic display stays continuously red, indicating no BIOS activity. Ideally, I'd like to get my hands on a service manual for this board, but if anyone can throw out common issues with this board as a starting point, that would be great. All of these boards have been in service for more than 3 years in 3 different machines. The failure appears to have identical symptoms. I would bet the component that has failed is common to all 3 boards. It seems other people are having the very same problem with these boards over several years of service. I have tried all of the usual troubleshooting tactics with no success. Thanks!

Check for bulging, leaking, ruptured capacitors near CPU socket.

Help! My K8n diamond plus wont start!

HELP! I've bought a MSI k8n diamond plus mother board, and it woont start, i've tested all my other hardware on my other computer, and it works fine. When i'm turning on my computer, it shuts down after a second. What is the problem?
/Jeppe

Quote from: Jeppar on 31-May-06, 21:15:19
What does it mean if it has a short...
There is a 12 Vatx Connecter on my motherboard with 8 pin, but on my power supply theres only four, i've connected it anyway, and it fits in, on the half of the connector.
Could that be the problem?
I use the same type of connectors, no need for converters.
I too have only 4 pins out of the 8 on the board connected, no problem at all....
And yes I do overclock
But big chance it's the PSU that can't cope, it has only 14A @ 12V1 & 18A @ 12V....not very much for a 500W....
Also, try to boot with just 1 stick of memory in slot 1.

K8N Diamond Plus microphone not working

Hello All...
Thanks to everybody who helped me with my cpu power problem - the computer is up and running wonderfully now. The only issue that I'm experiencing, and I'm fully prepared to accept user error, is the fact that my mic is not working, or the levels are EXTREMELY low. I have an antec case, and I used the pin header on the motherboard for front panel audio which contains a mic input and a line out (For me, it's for headset convenience without having to remove my speaker wire). Since both the pin header and the connector conform to Intel standards, I think that's not the problem. I've used the drivers on the CD as well as the drivers on the Creative site for Soundblaster Live 24 bit. Both the front and rear connectors (and either version of the driver, for that matter) yield very low volume from the microphone. I *could* suspect the headset, but it's fairly new and worked yesterday, and also, the earphone portion seems to work correctly.
Since you'll want my specs:
K8N Diamond Plus
Antec "Piano" case with 450 watt antec smart power supply
Geforce 7800GTX
dual pata drives (striping)
dual dvd rw drives
dlink wireless lan
Let me know if I can provide any other info, and thanks in advance for any assistance
Steve

Didn't seem to make any difference. I jumpered the pin header so that it was back to the way I got it out of the box. I even used a microphone for our camcorder, and that didn't seem to get any better result either. Very strange...........

Water cooling and the K8N Diamond Plus...

I have a water cooled DFI mobo atm and I want to change it to the K8N Diamond Plus and I noticed that the board has a heat pipe on the northchip and on some other component. My question is this; I want to put a water block on the northchip but I don't know if I can. Can I safely remove the heat pipe setup to put a water block on the north chip and if I do what about the other component that the heatpipe was covering? I hope I wasn't to confusing in the explanation.

Hello !!
You will need two Waterblocks, one for the north- second one for the southbridge.
There should be no Problems mounting the blocks if the mounting holes fit the mainboard.
You can easily remove the Heatpipe. You have to squeeze those nipples togehter tha are on the backside of the board. You can do it manually but you can also use a cylindric tool to squeeze them together. I cut a plastic pen i the half, and pushed it on those mounting latches carefully.
___|\ half pen
latch___ <----
|/ ___________
After this procedure the Heatpipe is only held from the thermal grease on the chipset.
Greetz

MSI K8N Diamond Plus - Guide to my first week

OK, not a newb here, but been around the block quite a bit. MSI K8N Diamond Plus is my 5th A64 mobo (ECS K8M800, my daily undestroyed computer, K8T800, my 12 year olds gamer, Asus A8V Deluxe, first 939 system, Abit AN8 SLI, first SLI gamer, and now the MSI Diamond Plus). Had the KDP (K8N Diamond Plus) for more than a week now, and here's what I've learned.
This is state of the art again, and we have no one to blame but ourselves for the pain this causes us when we upgrade like lunatics
And as usual, the drivers and BIOS are al Dente (i.e. not cooked enought yet, a little raw)
MSI is also oddly silent on this system, which is wierd, as they are a large company, and specifically cater to enthusiasts. But their BIOS guys are MIA. Hopefully this will not be forever. Asus, ABIT, DFI, Epox are always fast with fixes
The board is a nice design, with everything basically accessible, as much as any other board. Lots of purposeful components, not too many dumb frills. No tooty fruity colors, but rather practical parts.
The new 2 piece NForce chipset is fine, and the MSI guys gave us a decent, but funky cooler. It gets a little warm to the touch when you pound on it with Prime95, or Quake4, but other than that it is fine
The manual has a zillion typos, and fortunately for us in this forum, we have shared what we've learned. The translation from Chinese to English leaves quite a bit to be desired, and hopefully, MSI will learn from Asus and Abit and get a better translation service. In 2006 this is just plain stupid, especially with a $225 board
As usual, the mobo supplied tweaker utilities are just aweful. They look like a hallucination from a Hunter S Thompson book, and they work about as well. Core center is a sad state of affairs, and the rest of them just burrow their way into your otherwise stable system and cause it to have poor behavior. And therefore as usual, the BIOS is the best way, if slowest, to tweak this bundle of parts
Which brings us to the BIOS. IMHO, the worst one I've seen on a high end board. ZERO explanation for half the settings (this is not strange in and of itself, BIOS is still a black art, but in a tweakers board, we should have some basic explanation )
There seem to be adequate settings in the BIOS for all sorts of doodads and gizmos, but who the heck knows what half of them are. Roger points out rightfully, that we now need to "Tune" across all these different intermediary bus structures and test. But with the lack of info from either NVidia, MSI or anyone else for that matter, its kinda hard to know where to start.
The board is clearly sensitive, which is a result of it being high strung. This is no different than any "first out" product I've ever bought. Most take 2 or 3 turns of the crank to get totally stable and forgiving. This one hated my OCZ platinum EL 2Gb kit memory, and it brought out the worst in one of the SLI based EVGA 7800 GT COs. These components worked in the Abit AN8 SLI (although not always great), but the MSI has ZERO tolerance for even the slightest pertubation from the memory. It was BSOD city until I removed both of these components by process of elimination that took probably 100 hours
Once I removed the bad components, and replaced the memory with Geil Ultra X 2x512 2-2-2-5, it worked great, ran Prime95 for 10 hours with no errors, and seems reasonably stable. I've RMA-d the bad 7800GT CO back to EVGA, and will report back on how SLI behaves when I get the new one (cross shipped of course, I haveno patience )
I also now need to replace the 2Gb RAM kit with something that the board will tolerate. I may RMA the 2Gb kit back to OCZ and try another one, but I dunno. I love OCZ but I have a bad feeling about this, even though they have great!!! support. I may try OCZ PC4000 or the RAM that Roger successfully used.
I did upgrade to the 1.16 BIOS, and found that some new things were added, as well as voltage control in Cell was a little better, but registration of changes in voltage is still a disaster. I adjusted a bunch of times, it didn't register, and I ended up smoking a new A64 3700+ Diego with 1.95 volts, even though the BIOS claimed it was 1.53. I had to rebot to see what was going on. The Thermalright XP-90 kept the proc from melting down through the earth
Finally, I hope this board attracts more people, and therefore more tweakers that can figure out all these gadgets and settings. Everyone flocked to the Asus X16 SLI product, which is too bad, as this one needs lots o' folks to hack it up for us to figure out what is going on.
The on board Creative audio sounds lousy to my ears, and I will replace it with an Audigy 2ZS gamer that I had in the Abit. It just sounds better, but hopefully the drivers will not trash my newly stable system. Creative scares me, they scare me alot.
I've been able to get the CPU up to 2.4Ghz, with a .5 volt bump to the CPU and 2.9 volts into the Geil memory. So far, so stable, no smoke coming out yet
I hope this info is somewhat valuable to someone on this board. I will post details of all changes that I make, as others are doing, so we can at least take care of ourselves with this thing.

Quote from: nanohead on 15-February-06, 01:17:10
Which brings us to the BIOS. IMHO, the worst one I've seen on a high end board. ZERO explanation for half the settings (this is not strange in and of itself, BIOS is still a black art, but in a tweakers board, we should have some basic explanation )
There seem to be adequate settings in the BIOS for all sorts of doodads and gizmos, but who the heck knows what half of them are. Roger points out rightfully, that we now need to "Tune" across all these different intermediary bus structures and test. But with the lack of info from either NVidia, MSI or anyone else for that matter, its kinda hard to know where to start.
first of all, i do think that all the settings in the BIOS have an explanation in the manual, even if it's a basic one. if that explanation doesn't tell you everything in detail, is because if you do need a detailed explanation of the settings, you probably shouldn't be messing around with those settings.
Quote from: nanohead on 15-February-06, 01:17:10
I did upgrade to the 1.16 BIOS, and found that some new things were added, as well as voltage control in Cell was a little better, but registration of changes in voltage is still a disaster. I adjusted a bunch of times, it didn't register, and I ended up smoking a new A64 3700+ Diego with 1.95 volts, even though the BIOS claimed it was 1.53. I had to rebot to see what was going on. The Thermalright XP-90 kept the proc from melting down through the earth.
wanna tell me how did you get 1.95V on that mobo?
Quote from: nanohead on 15-February-06, 01:17:10
I've been able to get the CPU up to 2.4Ghz, with a .5 volt bump to the CPU and 2.9 volts into the Geil memory. So far, so stable, no smoke coming out yet
a 0.5V bump? again, you must be joking. maybe 0.05V.

K8N Diamond Plus 2x16... Arrival Imminent?

I noticed a strange thing when I was looking/pricing for my next mobo - SLI, naturally. I know that the Diamond Plus 2x16 isn't out yet but I thought I'd have a look just to "ballpark" my budget (Merry Chirstmas to me ) & I noticed something odd.
There is not a MSI SLI board to be had anywhere from 3 of the "BIG" sites that I've shopped so far - NewEgg, ZipZoomFly or Monarch. It is quite unusual for all to be out of a particular product at the same time. The single PCI-e boards are available at all 3, however.
Hopefully, this means that the K8N Diamond Plus 2x16 SLI is about to "hit the street"...
Just my contribution to the rumor mill.

Quote from: Tiresmoke on 26-November-05, 00:20:47
When you get one maybe you could take a couple close up pics of that new chipset cooler. I think it looks pretty nice but MSI did not post a good closeup of it so that folks could really get a gist of what it is.
It would also be pretty cool to get some compairison between how well it works versus the existing cooling solution.
Looks like a heatpipe thing... similiar to what some others are starting to use.
From what I've read, they can work pretty well - as long as there is sufficient air moving through your case that is. If not much air is flowing they supposedly get pretty damned hot. That might be something that people running watercooling might take note of, if they're not running fans in their cases.
In any event, if I had one in front of me right now ready to install, the first thing I'd do is completely remove it to see if there's a good amount of thermal goo... & then promptly replace it with Artic Silver.
I've checked, then replaced the thermal compound with AS on every new board that I've gotten before installing since my ABIT days - at the time they were putting little or no compound on the chipset. Good thing it's become a habit - there wasn't exactly what I'd call a copious amount on my Neo either. Anyway, there's always benefits to doing that straight out of the box for obvious reasons.

CPU Usage 100%? K8N Diamond Plus

Never before have I witnessed the CPU being used at it's absolute maximum. It has been occuring regularily with my system. I noticed it first when my screen saver started getting jittery. This seems to occur most often about 1-2 minutes after windows finishes loading. It seems kind of odd to me that this occurs during typically idle system times. The memory usage also dramatically rises during these spikes, using ctrl+alt+delete I noticed svchost.exe to be the culprit of the memory usage atleast. The hard drive doesn't appear to be active when these events occur. Is this normal for this motherboard, or is this something that should be corrected?
I've always had 3 short beeps upon startup with this board, but it has never stalled the boot process. Anyone know what this means?
I've upgraded my board somewhat recently and carried over the CPU and memory from a older MSI model that used the same type. Could it be possible either or both are incompatible?
Also one, somewhat less important problem. First off I must say that the PS/2 power on feature is pretty cool. I used it with a wireless keyboard so I could turn on my PC from my living room HDTV (I have my comp wired through Y/Pr/Pb cables). Only problem is about one in every 4 or so shutdowns the system restarts immediatly when this feature is selected in the bios. Bios issue maybe?
System Info (and everything directly connected to it):
(pretty sure not all of this is relevant, but I figure it couldn't hurt)
MoBo: MSI K8N Diamond Plus
Memory: 1Gb (2x512 kit) Crucial PC3200 CT6464Z40B.C8TD (in slots 1 & 2)
Processor: Athlon 64 3200+ Winchester
GPU (only one): MSI NX7900GT-VT2D256E-HD (primary PCI-e)
Modem: SupraMax LE 56K Fax Modem (PCI)
HDD: WD Caviar 120Gb IDE (primary)
HDD: Maxtor 80Gb USB (external, non system)
3.5: Standard 3.5" floppy drive (a:)
5.25: Lite-on 48x CD burner (secondary slave)
5.25: Sony DVD rom (secondary master)
PS: Antec SmartPower 2.0 500W
Human Interface: Wired Logitech KB & Mouse through USB (for primary use)
Human Interface: Wireless Logitech KB & Mouse through PS/2 (for remote use, often turned off)
Primary Monitor: Viewsonic P70f 17" CRT hooked to DVI #1 via RGB adapter
Secondary Monitor: Sony KDL-V32XBR1 32" HDTV through 1080i Y/Pr/Pb adapter, stereo audio
Speakers: harman/kardon
Connected to internet via Cat5 network, phone modem sometimes used when primary internet is down
OS: Windows XP Pro w/ SP 2 installed
Thank's in advance to anyone that can help me as I'm pretty much stumped at this point.

Quote from: mdawgmike on 11-November-06, 11:25:18
Any other suggestions?
how about this:
Quote from: BOSSKILLER on 03-November-06, 23:14:30
get Process Explorer to determinate in details what make this CPU usage: http://www.sysinternals.com/Utilities/ProcessExplorer.html
it has more detailed information than the built-in task manager.

K8N Diamond Plus BIOS problems

Hi , just replaced my lanpartyUT sli-dr expert with K8N Diamond Plus mobo and having problems allready :D
Just finished overclocking and now running at (250 x 11 x 800mhz x 1.300v+0.2v x dram/fsb 1/1 x 2.80v)
Memory timings --> (3,7,14,3,2,8,2,2,1,3,200mhz(15.6us),1,16x,7x,7ns,5ns,0clk,DiCC:enabled,1T,8beats,reduce 00%... ...)
The problem is "BOOT" related... System is PRIME95 stable , but still when trying to "restart windows" or "reset" the system wont BOOT !!?
When i shutdown and then power up, the system boots perfectly !? What can cause this kind of behaviour :/
I have OC:d quite many systems , but this is new even to me

The windows core program shows htt link 1000mhz exact. Memory settings are all "manually" adjusted. Cpu vcore is 1.300 & extra voltage 0.2v=1.5v.
All ECC options are disabled.Hdd:s adjusted manually. Should i rise the (NB) voltage , or does that have anything to do with this !? Maybe not at 250fsb only :D Cool & quiet is disabled naturally :/ All fan controls disabled , connected directly to psu. No D.O.T,s or anything automatic overclocking enabled. The (L cache & data cache scrubs) are strange to me, so those are disabled.After flashed bios , enabled boot sector protection. All the mobo power connectors are in use (24pin+8pin+4pin) Could it be that the memory modules should be used on ports 3 & 4 (now on 1 & 2) ??
The mushkin redline xp4000 memory specs Fortron Epsilon 700W Psu specs
Output Voltage Min. load Max. load      Load Reg.     Ripple & Noise
Frequency:   500MHz +5V     0.5A     30.0A     +-5%     50mV P-P
Latency:   3-3-2-8 +12V1   0.0A     18.0A     +-5%     120mV P-P
Parity:   Unbuffered +12V2   0.0A     18.0A     +-5%     120mV P-P
Voltage:   2.6V-2.9V +12V3   0.9A     18.0A     +-5%     120mV P-P
Module:   128MX64 +12V4   0.1A     18.0A     +-5%     120mV P-P
Chip:   64MX8 +3.3V   0.8A     36.0A     +-5%     50mV P-P
Pins:   184 -12V     0.0A     0.8A     +-10%     120mV P-P
+5Vsb   0.0A     3.0A     +-5%     50mV P-P

K8N Diamond Plus & heatsink

Hi all, Im new to the forums.
I was wondering if a Zalman 7000B would actually fit a K8N Diamond Plus because Im getting one soon, and if not please recommend me some good aftermarket heatsinks that fit the board.
Thanks in advance.

List all your hardware in full details including the PSU and BIOS revision and put it in your signature. Well, I'll recommended you using the water cooling system since it's now quite cheap and easy to maintain/get the good temperatures. gd luck.

K8N Diamond Plus Questions?

I have a some questions about my K8N Diamond Plus. I recently replaced a K8N Neo Nforce 3 board and some other parts as well. The machine has been working very well with this new board so far but there are a few issues I’d like to get resolved.
1. Does anyone know if there is a new BIOS out for this board? I have that problem where at start up it shows that I have a new card in one of my PCI slots even though I do not….it does’nt seem to hurt the machine at all it’s just annoying….i’m wondering if they released a BIOS that corrected that?
2. On my old board I overclocked the machine with no problems at all. Now I’m no expert at over clocking but I do like to dable a little and last time I did I had no problems. This board seems like it will over clock well so I went and got better RAM….i just received some Corsair XMS 2GB DDR 400. I went into the Cell Menu to look at the options for the RAM and saw much, much more then I had on my old Neo board.
I know I need to adjust the CAS Latency, RAS# to CAS# delay, Min RAS# Active Time and the Row Precharge Time for this RAM….people have been saying that their motherboards do not detect the correct timings for this RAM (2.5-3-3-6) so you need to adjust it Manually…along with uping the Voltage to 2.7.
My question is…..do I need to worry about any other options under the MCT Timing Mode besides the 4 I mentioned above? Also…I could’nt seem to adjust the Voltage for the RAM? Every time I high lighted it and hit enter nothing would pop up for me to adjust (and it is white not gray like some things are)….is there something I’m missing that I need to shut off in order to access it???
Thanks ahead of time for anyone that can provide me with some answers.

I have not been able to find any information on those other settings. It is my current project and I am not having a great amount of success.
The defaults for them do not seam to have any adverse effect on stability the system in my signature is my MS-7220 system at FSB=225, CPU multiplier of 12, Memory/FSB =1/1 system is quite stabile if I am not playing with the BIOS settings.
I am working on, some major some minor these current problems. Watch out for number three it will flat blow your BIOS Parameters. It happens on my system every time, but I not been able to find any body that is will to trash the BIOS to verify it, so I can be sure it is a real BIOS problem or my system. “MCP Timing Mode” use to do the same thing, that where the V1.16 BIOS version came form MSI Tech Support sent my that one to fix the problem and this one looks to be the same.
1.   First boot screen the line “DRAM = 400 MHz, Dual-Channel.” It reads 400 MHz do matter what that actual memory transfer rate actually is.
2.   Cell Menu parameter “Adjust DDR Voltage (V)”, has two problems (1) the BIOS default voltage is outside the manufacture specification for normal operating range. BOIS default is 2.65V and manufacture states the Memory Module should be operated between 2.7V minimum and 2.9V maximum. (2) The voltage cannot be set to the manufactures minimum voltage of 2.7V. Starting with the BIOS default voltage of 2.65V and you press “+” key once and voltage jumps to 2.75V, press the “-“ key and the voltage jumps back to BIOS default of 2.65V.
3.   Cell Menu>Memory Configuration>User Config Mode parameter, when set to “Manual” and all of the “User Config Mode” sub-parameters left at BIOS default. The system will not boot. When I say will not boot I mean Blank Screen, no beeps, no drive activity, just case and motherboard fans come on.
4.   Menu “CPU Frequency Configuration”, parameter Adjust CPU VID. CPU correct voltage tracks the set by about 0.03V high. Example: if Adjust CPU VID to 1.375V and actual vCore voltage is about 1.405 Volts. The offset is maintained through the voltage adjustment range of the current CPU.
Roger
When submitting a problem, include a complete list of your system components; include part numbers, all Power Supply Voltages, and their output ratings. It is almost impossible to estimate what your problem is without knowing something about it.

K8N DIamond Plus- 4 sticks of memory problem

I have a new Opteron 180 with a K8N Diamond plus mb. I am thinking about getting another 2g of memory to run with my current 2g of 3200 memory to speed up Vista even more. I thought the new chips could run 4 sticks of memory at 400 with a command rate of 2t. I wanted to try to see if it would work so I pulled two 512 pc3200 sticks from my wifes computer and installed it. At boot up it clocked the memory to 333 (which I expected it to actually) and I got into the bios and set it to 400 with 2t command rate and everything else at default settings. All the memory is Kingston value ram. The computer randomly booted and I had lockups at 400, but at 333 it ran fine, but I still couldn't run the memory at 1t with 333. I am using bios 1.33 as the other bios's always set the HT bus wrong for me. Is this just a function of the motherboard or is the memory not compatable with each other? I thought the motherboard is irrevelant since the memory controller is on the cpu?
Thanks for your help,
Scott

The memorycontroller IS inside the CPU.
And some are lucky to get it stable booting at DDR400 with 4 sticks, some get crashes.
However, most have drop-backs to DDR333.
It's a CPU limitation when using unbuffered memory.
Buffered memory should be able to do it, however, I'm not quite sure as this is an S939 type CPU.
You could try something if you know somebody that has buffered memory.
Sometimes it helps if you lower the other timings.

2 'problems' with the K8N Diamond Plus

Hi there.
I just bought a K8N Diamond Plus and I'm having some troubles installing my system in conjunction to my Decklink Extreme PCI-E ( http://www.decklink.com/products/sd/ ).
Here's my configuration:
MSI K8N Diamond Plus
AMD64 X2 4400+
ROSEWILL 6600GT PCI-E VGA
Decklink Extreme PCI-E
2GB RAM ( 2 x 1gb) Kingston
OCZ-520 12U Modstream Power Supply
plus 6 HD's (7200rpm) and 1 DVD-+RW
The problem is, when I try to initialize the system with the Decklink, which it's a PCI-E 1x, it just don't boot. Neither putting the Decklink on the 1x, nor in the 4x slot and nor in the 16x.
The Decklink is working just fine in another system and doesn't seem to be a problem with this card.
I wondered if there's any limitation in the K8N Diamond Plus with working with the ROSEWILL 6600GT PCI-E VGA plus the Decklink.
=======================
The other thig is that when I take off the Decklink, the system boots normaly but a message appears while booting: "Not enough space to copy PCI option ROM 00:13:00".
And I don't have a clue about what's going on.
=======================
Please enlighten me with this questions if possible.
Thank you very much.
Greets.
Igor Bineli

Remove the battery away for 10 minutes, clear CMOS, start the system to load setup/optimized defauts in bios setup. After that, disable all onboard items in bios setup that you won't to use. Save and exit.
Plug ROSEWILL 6600GT PCI-E VGA card, and start your system to check if there is the error message. If there is, borrow another brand VGA card to do a test.
Besides, update your MB bios and driver version to the latest one.

K8N Diamond Plus - Cool'n'Quite - Not Starting At Full Speed Everytime. Why?

Similar Messages

Maybe you are looking for