K8N Diamond plus HSF and memory compatability question

I am considering this board since I need a good onboard sound chip to utilize my front breakout box. At this time I have an opteron 180, a Zalman 7700 and 2 gb kit of Corsair XMS TWINX2048-3500LLPRO on the way from ZZF. I had planned on using this on an Asus A8N SLI deluxe but if the hardware is compatible I would rather have the SB onboard than the Realtek on the Asus.
Does anyone know if the Zalman will fit on this board and clear the northbridge heatsink and fan? I had seen in another post the the MSI boards might not care for Corsair to well, any validation on this?
Thanks!

Tricker61,
As you can see by my signature I am using the Diamond Plus with a full two pair of TWINX2048-3500LLPRO’s.
It was not plug them in a go, but it just requires setting the memory up manually, which is really set forward.
The only problem is that the current BIOS do not the memory to SPD values and here is a list of setting you will have to set manually.
(1)   FSB/Memory Ratio is set by default to 1:2, which needs to be changed to 1:1.
(2)   Memory Module Voltage Corsair spec is 2.7 – 2.9, default BIOS setting is 6.5V. I am running mine at 2,75V.
(3)   Corsair spec timing 2,3,2,6, BIOS Default is 2,3,2,5 so you need to set that.
As far as memory set for your Corsair memory you have they are working fine and system is stable.
You wanted 2.6 GHz; I am currently run FSB of 225 MHZ and with default multiplier of x12, which is one BIOS defaults that is correct. My system running solid at 2.7 GHz and the memory is running DDR450, which better the Corsair spec.
Therefore, with the memory modules you should get the performance you said you wanted. I feel with all the memory setting corrected I could running it up more, first 225 MHz is the speed I could not make with default BIOS setting and I am not and Over-clocker like you, if want a good solid fast system.
If you have not purchased a case yet, make it a big one with lots of fans. I am using the Cooler Master CM Stacker 810 and have just moded the case to add two extra right side 120mm input fans in place of the stock 80mm fan and I am just starting to get the system temperatures under control. With to two new fans that makes 4 120mm input fans and 120mm, 85mm and the power supplies 135mm fan for exhaust. I have been using 120mm fan with 35 to 40 CFM each, to try and keep the noise down, but it looks like an a few more CFM to input fans and put up with the added. But it is a nice system now, you the noise of the air flow , but no actual fan sounds, except for the Graphics Card when is cycles it fan to high speed, which much less with two add right side 120mm fans.
Hope this information helps you selecting components for your new system.
Roger
When submitting a problem, include a complete list of your system components; include part numbers, all Power Supply Voltages, and their output ratings. It is almost impossible to estimate what your problem is without knowing something about it.

Similar Messages

K8N Diamond Plus, SLI and Creative X-Fi cards, anyone running similar?

Hi there!
I've got an ASUS A8N32-SLI board and my X-Fi card does not work with it, nor does it for many other people with similar setups.
See here:
http://forums.creative.com/creativelabs/board/message?board.id=soundblaster&message.id=31426
and here:
http://forums.creative.com/creativelabs/board/message?board.id=soundblaster&message.id=26289
I get crackling and popping noises when running most games, e.g. BF2, Fear, FarCry. When my 2x7800GTX's are in SLI mode it crackles loads, e.g. start far cry, click options, and listen. When i disable SLI mode it crackles less, but it still crackles. Many others encounter similar issues with their systems that are not identical but the symptoms are similar - high load = crackling/popping.
My question is:
Is anyone here sucessfully running any X-Fi card (music, fatality, elite pro, etc) with 2x video cards and NO crackling/popping in BF2, FEAR and FarCry?
I've already had a replacement X-Fi card from creative which their tech guy said "should" fix it, lol, I'm wondering wether to replace my A8N32-SLI with an K8N Diamond Plus to fix the problem. Besides, the MSI board has better PCI slot location and works with nTune too unlike the ASUS board.

What's going on guys.
I hate to see peep's having soooo many prob's and it sucks major BALLZ. The reason why I'm reposting is that I encountered a new issue. Not with my rig, but a friend's.
We pretty much have the same setup. Differences are he's using 2GB of Corsair DDR400 (which is picking up as DDR333 as well), different branded video cards (I'm running two EVGA 7800GT's in SLi, he's running two BFG 7800GT's in SLi), XFi Platinum (me, Fatality Edition) and he's got a dedicated ITE RAID PCI card for his RAID from his previous rig. Configured his BIOS pretty much the same way I have it running (he wanted to Overclock his AMD x2 4400+ to 2.6 GHz), but when it came to installing Windows we kept getting BSOD's during installation. Looked over things numerous times and it didn't make sense. We resetted the BIOS to default settings and Windows went through without a hitch. We tried OC'ing it one more time and Windows was fine. But, when he installed and ran Quake 4, either Windows or the game would just lock up. He booted back into the BIOS and put the CPU back at stock frequency of 2.2 GHz. Game ran flawlessly afterwards. That points at the processor. The only differences were we both have different stock fans and his CPU was manufactured in July '05. Mine in Sept '05. His rig also reports the infamous "Phantom" PCI modem as well.
Quake 4 is the only game he's got installed so far, but he reports everything is set to their highest qualities, including resolution. He said it runs great with no anomalies. He's going to install Dawn of War and Winter Assault later I know.
Me? I haven't run into any issues with any games either, including F.E.A.R. as Hydrasworld asked. Both of our sound cards are in the Communication PCI Slot of the motherboard. My take on the OC issue is since we're using different proc's from different wafers, maybe my chip had revisions in September that the July proc my friend has didn't. Also, his heatsink has one less copper pipe I noticed. I'll still drop by for help. Good luck to you all and the only other thing I can add is try using the latest drivers for each piece of hardware you've got.
LPB
P.S. If you can and you purchased a retail version of the processor, on one of the sides of the carton insert for the processor, a date should be printed. Maybe that can explain some issues. Once more, my proc was manufactured September 15th, 2005.

K8N Diamond Plus BIOS problems

Hi , just replaced my lanpartyUT sli-dr expert with K8N Diamond Plus mobo and having problems allready :D
Just finished overclocking and now running at (250 x 11 x 800mhz x 1.300v+0.2v x dram/fsb 1/1 x 2.80v)
Memory timings --> (3,7,14,3,2,8,2,2,1,3,200mhz(15.6us),1,16x,7x,7ns,5ns,0clk,DiCC:enabled,1T,8beats,reduce 00%... ...)
The problem is "BOOT" related... System is PRIME95 stable , but still when trying to "restart windows" or "reset" the system wont BOOT !!?
When i shutdown and then power up, the system boots perfectly !? What can cause this kind of behaviour :/
I have OC:d quite many systems , but this is new even to me

The windows core program shows htt link 1000mhz exact. Memory settings are all "manually" adjusted. Cpu vcore is 1.300 & extra voltage 0.2v=1.5v.
All ECC options are disabled.Hdd:s adjusted manually. Should i rise the (NB) voltage , or does that have anything to do with this !? Maybe not at 250fsb only :D Cool & quiet is disabled naturally :/ All fan controls disabled , connected directly to psu. No D.O.T,s or anything automatic overclocking enabled. The (L cache & data cache scrubs) are strange to me, so those are disabled.After flashed bios , enabled boot sector protection. All the mobo power connectors are in use (24pin+8pin+4pin) Could it be that the memory modules should be used on ports 3 & 4 (now on 1 & 2) ??
The mushkin redline xp4000 memory specs Fortron Epsilon 700W Psu specs
Output Voltage Min. load Max. load      Load Reg.     Ripple & Noise
Frequency:   500MHz +5V     0.5A     30.0A     +-5%     50mV P-P
Latency:   3-3-2-8 +12V1   0.0A     18.0A     +-5%     120mV P-P
Parity:   Unbuffered +12V2   0.0A     18.0A     +-5%     120mV P-P
Voltage:   2.6V-2.9V +12V3   0.9A     18.0A     +-5%     120mV P-P
Module:   128MX64 +12V4   0.1A     18.0A     +-5%     120mV P-P
Chip:   64MX8 +3.3V   0.8A     36.0A     +-5%     50mV P-P
Pins:   184 -12V     0.0A     0.8A     +-10%     120mV P-P
+5Vsb   0.0A     3.0A     +-5%     50mV P-P

Clicks with K8N Diamond Plus

Guys,
Maybe some one here can solve this one.
As you can see in my sig: I have a K8N Diamond Plus board and I love it! Rest of the specs are in my sig as well. I have a weird thing with it for some time, but it seems to be getting worse or, putting it right, it occurs more and more.
The pc is running just fine. Sometimes there's coming two clicks out of the case, about 1/2 a second after each other. It sounds like a mechanical something, but I'm unable to locate where it comes from. The pc simply keeps on working. No hangs, no BSOD's, it's fine. The only thing is that the sound is interupted shortly with each click.
To make it visible:
------------------click-----click-------------
- = computer noise
# = music playing
When I watch a movie, the same happens. Video-playback, however, isn't interupted at all.
Does anyone have any suggestion what this could be?
Thanks!
Hans
PS: I had a simular setup first with the K8T Neo2 board. The problem never occured with that board, so I asume it's the mobo that's doing this somehow.

Quote from: Hans on 20-December-06, 18:37:28
Well, I'm unable to find any problems. There's no data losses or whatever.
@Bosskiller: are you saying that this could be normal?
Do you know if WD Raptors make this sound? Or maybe Seagate Barcuda's (SATA-II)?
The more I try to locate the sound, it looks like it's one of the Raptors (or both).
yes sound normal for me, for Raptor don't know, for seagate think no, HITACHI(my currently doing the same), and Maxtor(DM 9 got before also making click/click)

K8N DIamond Plus- 4 sticks of memory problem

I have a new Opteron 180 with a K8N Diamond plus mb. I am thinking about getting another 2g of memory to run with my current 2g of 3200 memory to speed up Vista even more. I thought the new chips could run 4 sticks of memory at 400 with a command rate of 2t. I wanted to try to see if it would work so I pulled two 512 pc3200 sticks from my wifes computer and installed it. At boot up it clocked the memory to 333 (which I expected it to actually) and I got into the bios and set it to 400 with 2t command rate and everything else at default settings. All the memory is Kingston value ram. The computer randomly booted and I had lockups at 400, but at 333 it ran fine, but I still couldn't run the memory at 1t with 333. I am using bios 1.33 as the other bios's always set the HT bus wrong for me. Is this just a function of the motherboard or is the memory not compatable with each other? I thought the motherboard is irrevelant since the memory controller is on the cpu?
Thanks for your help,
Scott

The memorycontroller IS inside the CPU.
And some are lucky to get it stable booting at DDR400 with 4 sticks, some get crashes.
However, most have drop-backs to DDR333.
It's a CPU limitation when using unbuffered memory.
Buffered memory should be able to do it, however, I'm not quite sure as this is an S939 type CPU.
You could try something if you know somebody that has buffered memory.
Sometimes it helps if you lower the other timings.

K8N Diamond Plus Questions?

I have a some questions about my K8N Diamond Plus. I recently replaced a K8N Neo Nforce 3 board and some other parts as well. The machine has been working very well with this new board so far but there are a few issues I’d like to get resolved.
1. Does anyone know if there is a new BIOS out for this board? I have that problem where at start up it shows that I have a new card in one of my PCI slots even though I do not….it does’nt seem to hurt the machine at all it’s just annoying….i’m wondering if they released a BIOS that corrected that?
2. On my old board I overclocked the machine with no problems at all. Now I’m no expert at over clocking but I do like to dable a little and last time I did I had no problems. This board seems like it will over clock well so I went and got better RAM….i just received some Corsair XMS 2GB DDR 400. I went into the Cell Menu to look at the options for the RAM and saw much, much more then I had on my old Neo board.
I know I need to adjust the CAS Latency, RAS# to CAS# delay, Min RAS# Active Time and the Row Precharge Time for this RAM….people have been saying that their motherboards do not detect the correct timings for this RAM (2.5-3-3-6) so you need to adjust it Manually…along with uping the Voltage to 2.7.
My question is…..do I need to worry about any other options under the MCT Timing Mode besides the 4 I mentioned above? Also…I could’nt seem to adjust the Voltage for the RAM? Every time I high lighted it and hit enter nothing would pop up for me to adjust (and it is white not gray like some things are)….is there something I’m missing that I need to shut off in order to access it???
Thanks ahead of time for anyone that can provide me with some answers.

I have not been able to find any information on those other settings. It is my current project and I am not having a great amount of success.
The defaults for them do not seam to have any adverse effect on stability the system in my signature is my MS-7220 system at FSB=225, CPU multiplier of 12, Memory/FSB =1/1 system is quite stabile if I am not playing with the BIOS settings.
I am working on, some major some minor these current problems. Watch out for number three it will flat blow your BIOS Parameters. It happens on my system every time, but I not been able to find any body that is will to trash the BIOS to verify it, so I can be sure it is a real BIOS problem or my system. “MCP Timing Mode” use to do the same thing, that where the V1.16 BIOS version came form MSI Tech Support sent my that one to fix the problem and this one looks to be the same.
1.   First boot screen the line “DRAM = 400 MHz, Dual-Channel.” It reads 400 MHz do matter what that actual memory transfer rate actually is.
2.   Cell Menu parameter “Adjust DDR Voltage (V)”, has two problems (1) the BIOS default voltage is outside the manufacture specification for normal operating range. BOIS default is 2.65V and manufacture states the Memory Module should be operated between 2.7V minimum and 2.9V maximum. (2) The voltage cannot be set to the manufactures minimum voltage of 2.7V. Starting with the BIOS default voltage of 2.65V and you press “+” key once and voltage jumps to 2.75V, press the “-“ key and the voltage jumps back to BIOS default of 2.65V.
3.   Cell Menu>Memory Configuration>User Config Mode parameter, when set to “Manual” and all of the “User Config Mode” sub-parameters left at BIOS default. The system will not boot. When I say will not boot I mean Blank Screen, no beeps, no drive activity, just case and motherboard fans come on.
4.   Menu “CPU Frequency Configuration”, parameter Adjust CPU VID. CPU correct voltage tracks the set by about 0.03V high. Example: if Adjust CPU VID to 1.375V and actual vCore voltage is about 1.405 Volts. The offset is maintained through the voltage adjustment range of the current CPU.
Roger
When submitting a problem, include a complete list of your system components; include part numbers, all Power Supply Voltages, and their output ratings. It is almost impossible to estimate what your problem is without knowing something about it.

New K8N diamond plus questions please help.

Hi all well i am new to this msi site and am thinking of buying the new MSI K8N Diamond plus motherboard, the problem i have is that i have been a fan of ASUS and have had there last 3 SLI motherboards of which i have not been happy with.
Well i am totaly into overclocking and have an Opteron 165, balistix ram, 600w Enermax PSU, 2x Gainward 6800gt's,
what i am looking for is a motherboard that does what i says it will do, yes the asus a8n32 was a great motherboard but has a limitation on the voltage if useing the new E4-E6 stepping cores of which would only give a max voltage of 1.58v of which the asus spec said 1.76v.
What i am asking you chaps is is this a great motherboard, can you play with all the coms settings without any limitation, or do you think that the DFI motherboard is better.
If you can let me have some info on this motherboard that would be great, as i can not seam to get any reply from MSI about some information.
what i am looking for is what is the max CPU voltage and is there any limitation on it for some chips.
what is the max voltage for the ram
what is the max voltage for the chipset.
any help on this would be great.

Quote from: Stick on 23-February-06, 17:46:08
there is no mobo that alows 4V for the memory. i think the DFI goes up to 3.4V and you can use a DDR Booster to get to 3.8V. the only mobo that is capable to pass 3.3V is the DFI since you can have the choice to select from which rail the memory will be powered (the 3.3V or the 5V). you don't have that option in any other mobo.
Hi thanks for the mail but i have just copied this from msi about this motherboard, see below.
1.Adjust CPU FSB Frequency:
You can adjust the desired "CPU FSB Frequency" by using "+,-" key. The default value of AMD Athlon™64 is 200MHz. The maximum value is 450MHz.
2.AMD Overclocking Configuration (CPU Ratio):
If the CPU is Athlon™64 FX series, the ratio range is from 4 to 25.
If the CPU is Athlon™64 series, the ratio should be set according to its model number. For example, the ratio range of 3000+ is from 4 to 9, and the 3200+ is from 4 to 10.
3.Adjust Extra CPU Voltage:
This is for adjusting CPU voltage while overclocking. Following the CPU default value, the maximum is 1.8V. The interval is 0.05V.
4.Adjust DDR Memory frequency:
The Memclock is the major part which has four different frequencies to match many kinds overclocking memory modules. The memory frequency settings includes DRAM/FSB=1/2, 2/3, 5/6, 1/1.
5.DDR Memory Voltage:
This is for adjusting memory voltage while overclocking. K8N Diamond Plus has a special design.We use jump to distinguish two level arrangement of voltage. In this way it can get maximum 4.1V for overclocking modules. As you can see the below pictures, the left one is the standard mode when jump hat is located at the top postion. The default value is 2.5V, and the maximum is 3.2V. The interval is 0.05V. As the right one, it is overclocking mode when jump hat is located at the under postion. The default value is 3.2V, and the maximum is 4.1V. The interval is 0.05V.
What i am asking is there any limitation on the cpu voltage like the asus a8n32 as this had a max voltage of 1.58v due to it having a limit put on it by recomendation of amd.

K8N Diamond Plus + Vista upgrade issues + Memory

When I go to install Vista Business , I receive an error before the install saying that my motherboard is Non-ACPI compliant. I went into the bios and and made sure that all ACPI settings were turned on. Also I installed 2 more gigs about a month ago and only see 3 gigs on post instead of the 4 that is installed. I tried to update my BIOS using the MSI utility but received a memory error saying it can detect the correct amount. I ran MEMtest and it passed .Here are my system specs:
K8n Diamond Plus - Bios ver 1.0
AMD Ath 64 x2 4800 toledo
4 gigs of Corsair XMS DDR433 3500LLPRO
2 x EVGA 7950 GT KO Superclocked 512mb
WD Raptor 74 ( OS)
WD SE16 320 gb (storage)
Plextor 18x
PC Power and Cooling Turbo Cool 510 SLI
XP SP2

Quote from: iampiglet on 02-February-07, 23:18:28
When I go to install Vista Business , I receive an error before the install saying that my motherboard is Non-ACPI compliant. I went into the bios and and made sure that all ACPI settings were turned on. Also I installed 2 more gigs about a month ago and only see 3 gigs on post instead of the 4 that is installed. I tried to update my BIOS using the MSI utility but received a memory error saying it can detect the correct amount. I ran MEMtest and it passed .Here are my system specs:
K8n Diamond Plus - Bios ver 1.0
AMD Ath 64 x2 4800 toledo
4 gigs of Corsair XMS DDR433 3500LLPRO
2 x EVGA 7950 GT KO Superclocked 512mb
WD Raptor 74 ( OS)
WD SE16 320 gb (storage)
Plextor 18x
PC Power and Cooling Turbo Cool 510 SLI
XP SP2
I have the same motherboard with 4GB Ram. I had to enable the memory hole in the memory configuration of the bios for it to see the full 4GB. However, Windows 32-bit will not show the full 4GB ram since 32-bit addressing limit is 4GB and all your peripherals have to be included like vid card memory, etc. So don't beat your head against your desk once you get your bios seeing the 4GB and Windows 32-bit doesn't. My Vista gives 2.8GB ram of my 4GB, some get more, but I know I have two video cards with 768MB ram also. I'm using 1.2 bios.
Incidently, I ordered an OEM Vista X64, it will be interesting to see if it sees all my memory since 64-bit can go up to enormous addressing ranges.
Good Luck

MSI-K8N Diamond Plus - which memory?

Hello,
I will soon buy the K8N Diamond PLus motherboard. For that motherboard, I have selected the following memory: Corsair 512 Mo DDR-SDRAM PC3200 CMX Cas-2. But I can not find if this is ok for this type of motherboard. Does someone knows something about that? ???
Thx in advance!

Marlysa,
I would suggest that you stay away from the corsair xms ram as i figured the sme thing when I built my system, that it,s Corsair and its the #1 selected ram and usualy the most compatible, But this is not the case with this motherboard it's very picky about hardware pretty much the same as DFI board's!!!
Of course the CORSAIR WEBSITE will tell you this they want youre money!!!!!! Their certainly not going to reccomend OCZ MEMMORY that's for sure!!!!!
Please reconsider youre decision as I myself have traveled down that road you about to take. Personaly I love Corsair ram and i certainly wont bash it, but get the OCZ5002048ELGEGXT-K it cost me $213.00 wth tax for 2 gigs instead of $160.00 with tax for the corasir xms 2- 512 sticks Believe me you will be thankful that you took my suggestion!!!!! with the new 1.20 BIOS at optimized default's it posts and configures itself automatically where as befor you would usealy have to configure it manually in bios to get it to post at 500mhz believe me this OCZ MEMORY ROCKS!!!!
Save youreself alot of this.... BUY IT!!!!!!
Brother Esau
P.S just check around the forum their's alot of peop[le that have issues with the DIAMOND PUS AND CORSAIR RAM.

K8N DIAMOND PLUS RAID 0+1 Question

I have K8N Diamond Plus due tomorrow as the base for the new system I am building. In addition I have 4 Western Digital 320GB SATA drives with 16MB buffers on the way to serve as my storage. My question is this, I would like to set the drives up in a bootable RAID 0+1 array. In fact I would like to have the ability to multi-boot from the array. Is this possible? If so, it would be greatly appreciated to hear recommendations on partioning the array. I would like to dual boot for sure and possibly add a third OS.
Thank you in advance,
--Sarge

like syar said, it will show up just as one harddrive on your machine. that means that you can do with it whatever you are able to do with 1 harddrive: partition, multi-boot etc. since this is your first 0+1 array, i wish you good luck. you're gonna have fun with it, i know i did with my first array (took me 4 hours to figure out what's what, but hey, there wasn't any MSI forum at that time )

Anoying issue with K8N Diamond PLUS and overclocking.

I just got the motherboard wehn i overclock and restart the PC either from windows or BIOS etc. The PC will not boot and have to turn it off then turn back on. Apart from this annoying issue it's a great board better theen my A8N SLi Premium mostly due to the extra CPU voltage yay :D Is anyone else getting this issue?
System spcs are
AMD Athlon64 X2 4400+ @ 2766MHz (1.6v)
2GB Crucial Tracer PC4000
2x DELL Slient Geforce 7800GTX 256MB card
Espison 700w SLi cert PSU with EPS CPU voltage connected
Koolance EXOS AI Watercooling
MSi K8N Diamond PLUS
2x 150GB Raptor X in RAID-0
Coolermaser RC-830 w/ 4x 140mm + 3x 120mm fans

thats funny mine did that when i first got it , but when i received my new memory and video card everything was normal...so i dont remember if it was the memory or the VC..i just totally forgot about it..funny though i thought it was only me

K8N Diamond Plus and Opteron 175

Anyone running a K8N Diamond Plus and an Opteron 175 ok?
Any problems?
Any tips?

Quote from: skippy9146 on 20-January-06, 08:51:51
They should run fine... as a Diamond Plus comes with a Dual Core compatable BIOS.
You'll have to post back with some news when you get it together.... I have a 165 that needs a new home.
thanks for the reply, i kinda figured it might support it, as the M8N Diamond does (accordingto the cpu support list) but MSI's site doesn't seem to have much info about the K8N Diamond plus, not even a single bios upgrade or anything.
I have an ASUS A8N32-SLI but i have 3 issues with it:
1) can't install vista 5270 - common problem, not just me
2) poor pci slot location when using 2 pci-express dual width gfx cards
3) only available pci slot shares an IRQ with 2nd gfx card, bad for sound cards
I was going to order one this weekend but i might just not bother now as someone else posted the xfi cards don't work with them (popping/crackling, just like i have now) and that was my main motivation for getting rid of my asus board as my xfi card doesn't work either.

Water cooling and the K8N Diamond Plus...

I have a water cooled DFI mobo atm and I want to change it to the K8N Diamond Plus and I noticed that the board has a heat pipe on the northchip and on some other component. My question is this; I want to put a water block on the northchip but I don't know if I can. Can I safely remove the heat pipe setup to put a water block on the north chip and if I do what about the other component that the heatpipe was covering? I hope I wasn't to confusing in the explanation.

Hello !!
You will need two Waterblocks, one for the north- second one for the southbridge.
There should be no Problems mounting the blocks if the mounting holes fit the mainboard.
You can easily remove the Heatpipe. You have to squeeze those nipples togehter tha are on the backside of the board. You can do it manually but you can also use a cylindric tool to squeeze them together. I cut a plastic pen i the half, and pushed it on those mounting latches carefully.
___|\ half pen
latch___ <----
|/ ___________
After this procedure the Heatpipe is only held from the thermal grease on the chipset.
Greetz

K8N Diamond Plus- bios freeze & question about temp/voltage monitor

A weird issue I had right after I setup my mobo last night was that I could not access the "PC Health" portion of the bios. If I tried selecting it, it would just freeze. Is this a known issue? I'm hoping a bios update may solve this one. Does anyone know anything about this?

Well I was mostly just asking if this was a known issue, so I guess "no" is all the answer I need... Now, what would be my best solution? I am assuming bios update, is there anything else that I should consider?
But if it helps, as I said its a brand new build, so I'm running the default bios. 1.00. My other components are: Silverstone Zeus 560w, 2GB of G.Skill pc4000, Raptor 74gb, 7900gtx, Opteron 165.
Also, since my other thread was locked (I figured seperating two different topics would make it easier for people to respond to specific questions, I apologize,) here's my other question pasted:
"I just set up my new system with this motherboard (K8N Diamond Plus,) an Opteron 165, Scythe Mine heatsink, and a Silverstone Zeus 560w. Its these components that lead to my question-
I am getting temps of about 31C idle, 41C load. Nice temps yes, but I'm not sure how accurate those are. That means that it is idling at 86F in a room that was probably in the high 70's, maybe 80. Seems a little too good to be true, but then again, I am used to Intel's furnace-like temps
Its the voltage reading that has me a bit more concerned though. Corecenter is reading my +5v as 5.36v, and my +12v as 12.28v. The +3.3v is reading about spot-on at 3.33v. I'm hoping that someone else who has this motherboard can tell me this- are the readings in Corecenter for this motherboard generally accurate, and should I be concerned about this?"
Thanks for any help you can give. No sig yet because I just registered an hour ago, I'll work on it.

I need help DDR voltage and latencies (K8N Diamond Plus)

I noticed my DDR voltage was incorrect in the bios and I don't know what "Auto" is doing with my timings. I have 2GB of Corsair TWINX2048-3200C2 DDR400 Memory installed on DIMM1 and DIMM2 of my K8N Diamond Plus board.
So far I've made the following changes (as my RAM's specs indicate) in the BIOS but I'm new to this (first build).
DDR Voltage 2.75V
CAS 2.0
tRCD 3
tRP 3
tRAS 6
I left everything else at it's default setting. Are there any other changes I should make?

Quote from: memeticvirus on 14-May-06, 15:41:10
I'm having an issue with the 1.10 BIOS that is preventing me from manualy setting the timings...The problem I'm having right now is deciding what BIOS to install and where to download it. Perhaps you could help me with that?
With pleasure! I had the same problem with the v1.10 BIOS, as did another member here. I flashed BACK to the v1.0 BIOS (make sure to use the command line switched (just run the batch file)) and was able to set timings, and then I flashed directly to the 3.0A BIOS and was able to adjust timings still. See my old thread here.
For my success (I don't know if any or all of these influenced it, but I'm just happy it works) in flashing I did the following:
Download the 1.0 (original) and 3.0A (latest "official") BIOS images from MSI's support site.
Downloaded the DrDos BIOS flash bootable ISO CD image from bootdisk.com
Used my ISO software to add the BIOS image files onto the ISO image.
Burned the ISO to CD.
Booted from the CD
Flashed to 1.0
Cut Power (flipped PSU switch in back), held down the CMOS reset switch button on the mobo and the power button for 45 seconds.
Powered up, set "Optimized Defaults" and set memory voltage to 2.75v and rebooted.
Set all "normal" BIOS parameters (boot devices, et al).
Windows (x64) loaded with no issues, Everest reported timings appropriately
Did the same procedure for the 3.0A BIOS, with similar success.
You can see my post or click on the link in my sig for detailed memory reports.
Quote from: RogerP on 15-May-06, 03:04:55
Are you running just one set of TWINX2048-3200C2's?
Just one pair. I fiddled with the CR and the only result was with the single known good DIMM my latency got slightly slower (like a 5ns drop), but still no love with 2 DIMMS. I think it is just dead. But this is not my story (at least not in this thread)...this is memticvirus's story.

K8N Diamond plus HSF and memory compatability question

Similar Messages

Maybe you are looking for