K8N Diamond Plus microphone not working

Hello All...
Thanks to everybody who helped me with my cpu power problem - the computer is up and running wonderfully now. The only issue that I'm experiencing, and I'm fully prepared to accept user error, is the fact that my mic is not working, or the levels are EXTREMELY low. I have an antec case, and I used the pin header on the motherboard for front panel audio which contains a mic input and a line out (For me, it's for headset convenience without having to remove my speaker wire). Since both the pin header and the connector conform to Intel standards, I think that's not the problem. I've used the drivers on the CD as well as the drivers on the Creative site for Soundblaster Live 24 bit. Both the front and rear connectors (and either version of the driver, for that matter) yield very low volume from the microphone. I *could* suspect the headset, but it's fairly new and worked yesterday, and also, the earphone portion seems to work correctly.
Since you'll want my specs:
K8N Diamond Plus
Antec "Piano" case with 450 watt antec smart power supply
Geforce 7800GTX
dual pata drives (striping)
dual dvd rw drives
dlink wireless lan
Let me know if I can provide any other info, and thanks in advance for any assistance
Steve

Didn't seem to make any difference. I jumpered the pin header so that it was back to the way I got it out of the box. I even used a microphone for our camcorder, and that didn't seem to get any better result either. Very strange...........

Similar Messages

3 ea MSI K8N Diamond Plus will not POST

I have 3 K8N Diamond Plus motherboards that recently started having intermittent problems POSTing to BIOS. I initially found it possible to boot by clearing CMOS and reentering my settings; however, over time these boards have gotten to where they will not POST at all. Power comes up, but the four-LED diagnostic display stays continuously red, indicating no BIOS activity. Ideally, I'd like to get my hands on a service manual for this board, but if anyone can throw out common issues with this board as a starting point, that would be great. All of these boards have been in service for more than 3 years in 3 different machines. The failure appears to have identical symptoms. I would bet the component that has failed is common to all 3 boards. It seems other people are having the very same problem with these boards over several years of service. I have tried all of the usual troubleshooting tactics with no success. Thanks!

Check for bulging, leaking, ruptured capacitors near CPU socket.

Can't get k8n diamond plus working with 4x1Gb

I managed to get the DDR memory frequency running at 333MHz using only 2x1Gb in the Green slots of the motherboard (as listed in page 2-7 of the K8N Diamond Plus Manual).
However, when I add the other 2x1Gb modules to the Purple slots, the system does not even come up.
I've then went back to 2x1Gb in the Green slots so that I can get the system to fire up, gone into the BIOS and adjusted the settings according to the configurations below and restarted.
I've then shut-down and re-inserted the other 2x1Gb into the Purple slots so that 4Gb is present, then rebooted but the system still does not come up.
Adjust CPU FSB Frequency: 200.0
Current DDR Memory Frequency (this is Read Only) DDR 333
Adjust DDR Memory Frequency: set to Manual
Memory Clock: Tried all of the following for DRAM/FSB 1/2,2/3,5/6,1/1,5/4
Does anyone know of any person who has got a K8N Diamond Plus working with 4x1Gb ?

Tried removing one of the video cards and disabling the sound card (as suggested by http://www.asktheramguy.com/v3/showthread.php?t=65436), but the system still didn't fire up with 4Gb RAM.
Hans,
I managed to find the D-Bracket and here's the sequence that the LEDs cycle through:
LED1
LED2
LED3
LED4
DESCRIPTION
1
red
red
red
red
System Power ON
2
red
red
red
green
Initializing Video Interface
3
red
red
green
green
Initializing Hard Drive Controller
4
red
red
red
red
System Power ON
5
red
red
red
green
Initializing Video Interface
6
red
red
green
green
Initializing Hard Drive Controller
7
green
red
red
green
BIOS Sign On
8
green
green
red
green
Assign Resources to all ISA
Row 7 of the table above indicates "BIOS Sign On" and this should start showing information about logo, processor brand name etc, but this does not occur.
The cycle (phases 1 to 8) then repeats incessantly.

K8N Diamond Plus - Cool'n'Quite - Not Starting At Full Speed Everytime. Why?

Hello,
I have a K8N Diamond Plus with a power supply that is 620W switching. +3.3V 25A, +5V 30A, +12V 18A, +12V 30A, nvidia 7900GT, amd x2 4400+. My computer will not start at full speed everytime if i enable cool'n'quite. If i disable cool'n'quite, of course, it will start at full speed. I have run multiple benchmarks, etc. using cool'n'quite at full speed and have never had any problems whatsoever. Using BIOS 1.1.
Can anyone suggest an answer, to get the computer to boot up everytime at full speed using cool'n'quite?
Thanks!

you don't need CoreCenter for Cool'n'Quiet to work
install the AMD64 Processor Driver from here:
http://www.amd.com/us-en/Processors/TechnicalResources/0,,30_182_871_9706,00.html
reboot your PC, ensuring Cool'n'Quiet is enabled in BIOS and CPU Multiplier is set to [Auto]
To enable the Cool ‘n’ Quiet feature on a Windows XP system, you have to change the power scheme. Open the ‘Power Options’ from the Control Panel. Choose the power scheme ‘Minimal Power Management’ and click ‘OK’ to enable Cool ‘n’ Quiet.
On a Windows 2000 or Windows ME system, an AMD Cool ‘n’ Quiet tab will appear under Power Options when the Cool ‘n’ Quiet software for Windows 2000 and Windows ME is installed. This must be set to “Automatic Mode” for Cool ‘n’ Quiet to be enabled.
AMD Cool'n'Quiet Installation Guide (.PDF, 653kb)

Why iPhone 6 Plus sound microphone not working, but in the case of sound recordings in conversation mode work?

Why iPhone 6 Plus sound microphone not working, but in the case of sound recordings in conversation mode work?

Sighhhh, wasted so much time yesterday and today going around Sony centre and then carphone warehouse. They told me to come back after Easter.
I came home, banged the phone against the wall and it worked.
Turned out that mic was working on loud speaker and when using headphones so I thought that the secondary mic is working and the main one (placed with the speakers) isn't. So I banged that part against the wall slightly (in plastic case to prevent scratches) then put the phone underwater, waited for it to dry and now it's working. Idk how well and if it's of perfect quality again but people can hear me well.

MSI K8N Diamond Plus - Guide to my first week

OK, not a newb here, but been around the block quite a bit. MSI K8N Diamond Plus is my 5th A64 mobo (ECS K8M800, my daily undestroyed computer, K8T800, my 12 year olds gamer, Asus A8V Deluxe, first 939 system, Abit AN8 SLI, first SLI gamer, and now the MSI Diamond Plus). Had the KDP (K8N Diamond Plus) for more than a week now, and here's what I've learned.
This is state of the art again, and we have no one to blame but ourselves for the pain this causes us when we upgrade like lunatics
And as usual, the drivers and BIOS are al Dente (i.e. not cooked enought yet, a little raw)
MSI is also oddly silent on this system, which is wierd, as they are a large company, and specifically cater to enthusiasts. But their BIOS guys are MIA. Hopefully this will not be forever. Asus, ABIT, DFI, Epox are always fast with fixes
The board is a nice design, with everything basically accessible, as much as any other board. Lots of purposeful components, not too many dumb frills. No tooty fruity colors, but rather practical parts.
The new 2 piece NForce chipset is fine, and the MSI guys gave us a decent, but funky cooler. It gets a little warm to the touch when you pound on it with Prime95, or Quake4, but other than that it is fine
The manual has a zillion typos, and fortunately for us in this forum, we have shared what we've learned. The translation from Chinese to English leaves quite a bit to be desired, and hopefully, MSI will learn from Asus and Abit and get a better translation service. In 2006 this is just plain stupid, especially with a $225 board
As usual, the mobo supplied tweaker utilities are just aweful. They look like a hallucination from a Hunter S Thompson book, and they work about as well. Core center is a sad state of affairs, and the rest of them just burrow their way into your otherwise stable system and cause it to have poor behavior. And therefore as usual, the BIOS is the best way, if slowest, to tweak this bundle of parts
Which brings us to the BIOS. IMHO, the worst one I've seen on a high end board. ZERO explanation for half the settings (this is not strange in and of itself, BIOS is still a black art, but in a tweakers board, we should have some basic explanation )
There seem to be adequate settings in the BIOS for all sorts of doodads and gizmos, but who the heck knows what half of them are. Roger points out rightfully, that we now need to "Tune" across all these different intermediary bus structures and test. But with the lack of info from either NVidia, MSI or anyone else for that matter, its kinda hard to know where to start.
The board is clearly sensitive, which is a result of it being high strung. This is no different than any "first out" product I've ever bought. Most take 2 or 3 turns of the crank to get totally stable and forgiving. This one hated my OCZ platinum EL 2Gb kit memory, and it brought out the worst in one of the SLI based EVGA 7800 GT COs. These components worked in the Abit AN8 SLI (although not always great), but the MSI has ZERO tolerance for even the slightest pertubation from the memory. It was BSOD city until I removed both of these components by process of elimination that took probably 100 hours
Once I removed the bad components, and replaced the memory with Geil Ultra X 2x512 2-2-2-5, it worked great, ran Prime95 for 10 hours with no errors, and seems reasonably stable. I've RMA-d the bad 7800GT CO back to EVGA, and will report back on how SLI behaves when I get the new one (cross shipped of course, I haveno patience )
I also now need to replace the 2Gb RAM kit with something that the board will tolerate. I may RMA the 2Gb kit back to OCZ and try another one, but I dunno. I love OCZ but I have a bad feeling about this, even though they have great!!! support. I may try OCZ PC4000 or the RAM that Roger successfully used.
I did upgrade to the 1.16 BIOS, and found that some new things were added, as well as voltage control in Cell was a little better, but registration of changes in voltage is still a disaster. I adjusted a bunch of times, it didn't register, and I ended up smoking a new A64 3700+ Diego with 1.95 volts, even though the BIOS claimed it was 1.53. I had to rebot to see what was going on. The Thermalright XP-90 kept the proc from melting down through the earth
Finally, I hope this board attracts more people, and therefore more tweakers that can figure out all these gadgets and settings. Everyone flocked to the Asus X16 SLI product, which is too bad, as this one needs lots o' folks to hack it up for us to figure out what is going on.
The on board Creative audio sounds lousy to my ears, and I will replace it with an Audigy 2ZS gamer that I had in the Abit. It just sounds better, but hopefully the drivers will not trash my newly stable system. Creative scares me, they scare me alot.
I've been able to get the CPU up to 2.4Ghz, with a .5 volt bump to the CPU and 2.9 volts into the Geil memory. So far, so stable, no smoke coming out yet
I hope this info is somewhat valuable to someone on this board. I will post details of all changes that I make, as others are doing, so we can at least take care of ourselves with this thing.

Quote from: nanohead on 15-February-06, 01:17:10
Which brings us to the BIOS. IMHO, the worst one I've seen on a high end board. ZERO explanation for half the settings (this is not strange in and of itself, BIOS is still a black art, but in a tweakers board, we should have some basic explanation )
There seem to be adequate settings in the BIOS for all sorts of doodads and gizmos, but who the heck knows what half of them are. Roger points out rightfully, that we now need to "Tune" across all these different intermediary bus structures and test. But with the lack of info from either NVidia, MSI or anyone else for that matter, its kinda hard to know where to start.
first of all, i do think that all the settings in the BIOS have an explanation in the manual, even if it's a basic one. if that explanation doesn't tell you everything in detail, is because if you do need a detailed explanation of the settings, you probably shouldn't be messing around with those settings.
Quote from: nanohead on 15-February-06, 01:17:10
I did upgrade to the 1.16 BIOS, and found that some new things were added, as well as voltage control in Cell was a little better, but registration of changes in voltage is still a disaster. I adjusted a bunch of times, it didn't register, and I ended up smoking a new A64 3700+ Diego with 1.95 volts, even though the BIOS claimed it was 1.53. I had to rebot to see what was going on. The Thermalright XP-90 kept the proc from melting down through the earth.
wanna tell me how did you get 1.95V on that mobo?
Quote from: nanohead on 15-February-06, 01:17:10
I've been able to get the CPU up to 2.4Ghz, with a .5 volt bump to the CPU and 2.9 volts into the Geil memory. So far, so stable, no smoke coming out yet
a 0.5V bump? again, you must be joking. maybe 0.05V.

K8N DIamond Plus- 4 sticks of memory problem

I have a new Opteron 180 with a K8N Diamond plus mb. I am thinking about getting another 2g of memory to run with my current 2g of 3200 memory to speed up Vista even more. I thought the new chips could run 4 sticks of memory at 400 with a command rate of 2t. I wanted to try to see if it would work so I pulled two 512 pc3200 sticks from my wifes computer and installed it. At boot up it clocked the memory to 333 (which I expected it to actually) and I got into the bios and set it to 400 with 2t command rate and everything else at default settings. All the memory is Kingston value ram. The computer randomly booted and I had lockups at 400, but at 333 it ran fine, but I still couldn't run the memory at 1t with 333. I am using bios 1.33 as the other bios's always set the HT bus wrong for me. Is this just a function of the motherboard or is the memory not compatable with each other? I thought the motherboard is irrevelant since the memory controller is on the cpu?
Thanks for your help,
Scott

The memorycontroller IS inside the CPU.
And some are lucky to get it stable booting at DDR400 with 4 sticks, some get crashes.
However, most have drop-backs to DDR333.
It's a CPU limitation when using unbuffered memory.
Buffered memory should be able to do it, however, I'm not quite sure as this is an S939 type CPU.
You could try something if you know somebody that has buffered memory.
Sometimes it helps if you lower the other timings.

2 'problems' with the K8N Diamond Plus

Hi there.
I just bought a K8N Diamond Plus and I'm having some troubles installing my system in conjunction to my Decklink Extreme PCI-E ( http://www.decklink.com/products/sd/ ).
Here's my configuration:
MSI K8N Diamond Plus
AMD64 X2 4400+
ROSEWILL 6600GT PCI-E VGA
Decklink Extreme PCI-E
2GB RAM ( 2 x 1gb) Kingston
OCZ-520 12U Modstream Power Supply
plus 6 HD's (7200rpm) and 1 DVD-+RW
The problem is, when I try to initialize the system with the Decklink, which it's a PCI-E 1x, it just don't boot. Neither putting the Decklink on the 1x, nor in the 4x slot and nor in the 16x.
The Decklink is working just fine in another system and doesn't seem to be a problem with this card.
I wondered if there's any limitation in the K8N Diamond Plus with working with the ROSEWILL 6600GT PCI-E VGA plus the Decklink.
=======================
The other thig is that when I take off the Decklink, the system boots normaly but a message appears while booting: "Not enough space to copy PCI option ROM 00:13:00".
And I don't have a clue about what's going on.
=======================
Please enlighten me with this questions if possible.
Thank you very much.
Greets.
Igor Bineli

Remove the battery away for 10 minutes, clear CMOS, start the system to load setup/optimized defauts in bios setup. After that, disable all onboard items in bios setup that you won't to use. Save and exit.
Plug ROSEWILL 6600GT PCI-E VGA card, and start your system to check if there is the error message. If there is, borrow another brand VGA card to do a test.
Besides, update your MB bios and driver version to the latest one.

K8N Diamond Plus, SLI and Creative X-Fi cards, anyone running similar?

Hi there!
I've got an ASUS A8N32-SLI board and my X-Fi card does not work with it, nor does it for many other people with similar setups.
See here:
http://forums.creative.com/creativelabs/board/message?board.id=soundblaster&message.id=31426
and here:
http://forums.creative.com/creativelabs/board/message?board.id=soundblaster&message.id=26289
I get crackling and popping noises when running most games, e.g. BF2, Fear, FarCry. When my 2x7800GTX's are in SLI mode it crackles loads, e.g. start far cry, click options, and listen. When i disable SLI mode it crackles less, but it still crackles. Many others encounter similar issues with their systems that are not identical but the symptoms are similar - high load = crackling/popping.
My question is:
Is anyone here sucessfully running any X-Fi card (music, fatality, elite pro, etc) with 2x video cards and NO crackling/popping in BF2, FEAR and FarCry?
I've already had a replacement X-Fi card from creative which their tech guy said "should" fix it, lol, I'm wondering wether to replace my A8N32-SLI with an K8N Diamond Plus to fix the problem. Besides, the MSI board has better PCI slot location and works with nTune too unlike the ASUS board.

What's going on guys.
I hate to see peep's having soooo many prob's and it sucks major BALLZ. The reason why I'm reposting is that I encountered a new issue. Not with my rig, but a friend's.
We pretty much have the same setup. Differences are he's using 2GB of Corsair DDR400 (which is picking up as DDR333 as well), different branded video cards (I'm running two EVGA 7800GT's in SLi, he's running two BFG 7800GT's in SLi), XFi Platinum (me, Fatality Edition) and he's got a dedicated ITE RAID PCI card for his RAID from his previous rig. Configured his BIOS pretty much the same way I have it running (he wanted to Overclock his AMD x2 4400+ to 2.6 GHz), but when it came to installing Windows we kept getting BSOD's during installation. Looked over things numerous times and it didn't make sense. We resetted the BIOS to default settings and Windows went through without a hitch. We tried OC'ing it one more time and Windows was fine. But, when he installed and ran Quake 4, either Windows or the game would just lock up. He booted back into the BIOS and put the CPU back at stock frequency of 2.2 GHz. Game ran flawlessly afterwards. That points at the processor. The only differences were we both have different stock fans and his CPU was manufactured in July '05. Mine in Sept '05. His rig also reports the infamous "Phantom" PCI modem as well.
Quake 4 is the only game he's got installed so far, but he reports everything is set to their highest qualities, including resolution. He said it runs great with no anomalies. He's going to install Dawn of War and Winter Assault later I know.
Me? I haven't run into any issues with any games either, including F.E.A.R. as Hydrasworld asked. Both of our sound cards are in the Communication PCI Slot of the motherboard. My take on the OC issue is since we're using different proc's from different wafers, maybe my chip had revisions in September that the July proc my friend has didn't. Also, his heatsink has one less copper pipe I noticed. I'll still drop by for help. Good luck to you all and the only other thing I can add is try using the latest drivers for each piece of hardware you've got.
LPB
P.S. If you can and you purchased a retail version of the processor, on one of the sides of the carton insert for the processor, a date should be printed. Maybe that can explain some issues. Once more, my proc was manufactured September 15th, 2005.

Someone tell me it aint so: K8N Diamond Plus nForce4

simple really work were buying a job lot of computer bits and pieces so i thought might as well bung a few things on for myself and take advantage of the discount, so a new mobo, memory, and graphics card ive got more than enough spares hdd, fans, dvd/cd drives
took all the stuff home tonight thought i would stick it altogether leave it installing with baby sitter and go pub. So build it and then look at it strangly thinking im missing something then it hits powersupply, bugger how could i forget the powersupply have no fear i'll just take it out of my other rig. so out it comes and i start connecting it all up then i come accross the 12v cpu connecter and i begin to search for a 4 pin connection on my shiny new mobo and what do i find a bloody 8pin one.
The mobo in question is MSI K8N Diamond Plus, nForce4 SLI X16, Socket-939
The power supply in question is found in my sig
My questions is am I screwed, will i have to wait till monday to order a new power supply then wait till it gets delivered or can i just ignore the little factor of 4pins into 8 doesnt fit slap it in switch on and not have the computer start blowing smoke at me. im suspecting a long wait till monday and a longer wait till delivery but stranger things have happened in the computer world

Quote from: thorpe on 17-June-06, 18:13:01
i'll be honest i was thinking your all bonkers
that's not a nice thing to say
Quote from: thorpe on 17-June-06, 18:13:01
got the wife to press the power on button
roflmao this is the best part. i think we should all make our wifes/girlfriends (or the male equivalents) to push the button after a heavy OC or after messing around with the system. that way you can blame it on them if something happens

Aftermarket HSF options for K8N Diamond Plus

Just built a new rig with the K8N Diamond Plus and am very pleased with the board -- worked great from first power up and with a little BIOS tweaking I have no trouble getting a 50% overclock from my dual core Opteron 170. No headaches at all, unlike my previous experiences with Abit boards.
The AMD heatsink fan unit (with heatpipes) provided with the 170 is not bad at all, but I'd like to replace it with a more capable unit, along the lines of the Zalman 9500, Scythe Ninja, Tuniq Tower 120, Thermalright XP-120, etc. The tall heatsink of the Nvidia NB is close to the CPU socket and quite high, so I'm not sure if any of these will fit. Anyone using one of these or similar heatsinks ? Please let me know if they fit, or did not fit.
Since I could find any of the 7800GTX 512MB boards I wanted, I'm using a single MSI X1900XT card right now but plan to go SLI in the future with 7900GTX cards driving the 30" Dell monitor. The ATI video board and nVidia mainboard surprisingly get along great, with no crashes so far and 3DMark06 scores above 6000 -- the X1900XT is an impressive piece, and much faster than the X800XT-PE I had in my previous computer. But the fan can be extremely loud and the Catalyst Control Center sucks. Unfortunately the old ATI control panel is no longer offered...

TimeReaper,
The problems your are talking about are not uncommon with this MS-7220. The BIOS Clear Circuit physically has problems and that is not something they are going fix with a BIOS upgrade.
The BIOS Clear Circuit actually trashing the values stored in the CMOS by not doing a complete clearing of the CMOS is causing the problem. What leaves trash for parameters, for the BIOS to use when rebooting.
Let give you an example that fits your case. You can set the BIOS to turn the system on at any give time and date. So, if the trash in CMOS is in those parameters storage location. Therefore, whatever trash value gets stored in the locations, as a dated and time, will turn the computer on at that time. So, you could of had the computer come on in the meddle of the night two week later. Now, think of all the functions the BIOS have and how many weird things people are having and do not know why. There is one guy that is a regular on the Forum how has been fighting a problem I know is caused by trash in the BIOS CMOS, but Strick and I have ask him to do a good CMOS clearing and he just will not do it. I even wrote out in great deal the over night CMOS clear procedure I use. It is a pain in the ass, but some times, I have too use it. I just had to use it, upgraded V3.09 using short CMOS Clear and had no problem. Used the short procedure again when upgrading to V3.0A and everything when to hell, had to finally use the long overnight procedure and reinstall Windows to get computer to run right again.
NoBS, when your computer goes BOOO during the night just plain it o MSI.
Roger
When submitting a problem, include a complete list of your system components; include part numbers, all Power Supply Voltages, and their output ratings. It is almost impossible to estimate what your problem is without knowing something about it.

K8N Diamond Plus boot problems

I just built a new computer and it was working fine for about a month. Then one morning when I started it up it wouldn't turn on. The front LED's turn on, and the fans all start, but nothing ever shows up on the screen. The set of four lights on the back show R R
G G
Nothing has changed since the pc was working fine. I haven't changed any bios settings or added any hardware or software. I did try resetting the bios using the CMOS jumper, but this didn't change anything. The lights on the back show that it is initializing ide drivers, but in the manual it also shows that it is one of the last steps in the start-up process, so i would think that the memory check, processor count, msi logo ect. should appear on the screen like it normally does. However, the LED that blinks when the hard drive is active never lights up, but when i open the case and feel the hard drive i can feel it vibrating like it is functioning properly. And if it is a hardrive failure, then shouldn't the bios still start up and show up on the monitor? I have heard that many weird problems can be attributed to the psu, but I have a 500w Antec Smartpower 2.0, which is a pretty reliable psu from what i've heard. Any help or suggestions would be welcome. Also, how would i test individual components to find out what is causing the problem? I think since everything is within a couple of months old i should be able to get replacements. Thanks in advance for any help.
System Spec:
MSI K8N Diamond Plus
AMD Athlon X2 3800+
Nvidia 7600 GT
Maxtor DiamondMax 300gb ultra16
2gb Corsair Twinx xms ddr400
500w Antec Smartpower 2.0
Thanks!!

Quote from: Mikeyp926 on 15-August-06, 12:58:47
You guys are awesome! Thanks a bunch for the info on ram, I feel like I understand it better and I looked and found all the stuff in the bios that you guys were talking about. I'm downloading speedfan currently and will go install it on my other computer. I tried swapping the sticks of memory, but i ran into the same problem i did before. So i'm assuming that i can safely say one stick is faulty right? And do any of you guys have any experience trying to get replacement memory from crucial? I'll have to go poke around their website also. Well, thank you all so much for all of your help. This is my first home built pc and i'm trying to learn alot about them. Once everything is running properly i may try a little overclocking, but i'd like to get everything running smoothly first. Just out of curiosity, what would make a stick of ram go bad like that? It was only a month old, and i thought crucial xms was pretty good ram. Is it not? or did i just get unlucky?
Thanks a ton for all the answers, this forum is the most helpful one i've ever seen. thanks!
Maybe that you're unlucky to get those faulty RAM. Crucial RAM is not bad if you get the better performance if you're ocing your PC if or else get the value RAM if you don't oced.
Quote from: Svenomous on 15-August-06, 12:55:00
Speedfan 4.29 works with the K8N Diamond Plus. I have it running now
Ok. Get it but not sure about MBM as it seems that it don't support it. :p

K8N Diamond Plus incompatible w/ENERMAX Liberty ELT620

Howdy folks, 1st post and yet I'm about to loose my AMD virginity, so please be gentle.
The new build has already been purchased and is in transit, so info would be greatly appreciated.
I a$$umed 620W Liberty with 12v combined @ 36A is over blown.
That is until I found this site. Still shaking my head at the high amperage needed for this type of bleeding edge tech.
I’m just stunned that (2) 12v 22A rails are considered underpowered…
So any one have any success with this woefully <sarcasm ON> under powered cheap <sarcasm OFF> Enermax 620?
I really need the power and drive connectors, but most of the 26A PS would have too narrow of a head room.
I am well over budget, and the peripherals should be here for a weekend build.
Hoping folks with the Diamond plus and Enermax ELT620 could please post experiences.
Not sure if the second MoBo power plug works off the “other” rail, since I have not even seen this PS or K8N Plus.
Of course, I will post results.
Thank you for your time
Early March build
MSI K8N Diamond Plus
   Factory BIOS this time
Opty 165 Denmark
   ZALMAN CNPS9500
G.SKILL Extreme Series 2GB (2 x 1GB) DDR 500
SAPPHIRE Radeon X800GTO2 (100130VIVOL)
   Most stable driver for text/2D graphics @ 3200x1200
   ARCTIC COOLING AVC-AT5 Rev. 2 VGA Cooler
ENERMAX Liberty ELT620AWT ATX12V 620W
   +3.3V@28A, +5V@32A, +12V1@22A, +12V2@22A, [email protected], +5VSB@3A
(3x)Western Digital SE16 WD2500KS - SATA
(5) 120mm Fans & (2) 80mm +PS
ASUS DVD DRW-1608P2S
LITE-ON DVD-RAM SHM-165P6S
CM Stacker 810 RC-810-SKN1
XP Pro SP2
Snagged from my trusty ABIT ST6-RAID 1.4 PIII <old, like me!>
SIIG USB 2.0+1394+ULTRA PATA/133 RAID CONTROLLER
   (2x)Samsung 160G SP1614N – PATA
   Seagate 120 GB PATA ST3120026A-RK

In most cases it should be just fine. The only area where it may fall over in is DLI'ing two of the bigger Vid cards. The reason is in how dual rails split the power. As far as anyone can tell the best solution for SLI'ing two high amp vid cards is still with a single rail PSU. Outside of that the Liberty should be fine by all I can tell without trying it myself. That won't happen though as I gave up on Enermax due to the fact that I want Dual High Draw Vid cards and they simply don't fit that bill in my book any longer. Either you get Dual Rails from them or the wrong cable sets. That is why I went to OCZ.
Your milage may vary.

MSI K8N Diamond Plus Question

Will the ThermalRight XP-90C Heatsink and 92mm fan work with this board? Thermalright's web site does not say anyything but I can't help but wounder if it will fit with that fanless cooler on the MOBO.
Thanks

Quote from: nanohead on 15-February-06, 00:23:59
I've got an XP-90 installed and there is plenty of room. Plenty of airflow also. I'm at a constant 31-36 celsius, so no worries on the CPU. This cooler is large, I had it on an Asus A8V deluxe, an Abit AN8 SLI and now on the MSI K8N Diamond Plus, and its basically located on the same place regardless of mobo, so I wouldnt worry too much about it.
I did'nt mean that it has a massive effect on the temps, although comparing your rig to my last (AN8 Ultra, 3700 @ 2.7) my temps never went above 32'c idle and 44'c loaded!!
I meant that the airflow in my case struggles a little because the exhaust fan is right next to the hs and I cannot operate it the other way round due to my ram hs being so bloody large <damn you Corsair!!>
Sorry if I caused confusion!!

K8N Diamond Plus & Asus EN7800GT Dual ?

Howdy!
Bought one of the Asus Dual 7800GT graphics cards (two GPUs on one board) and was using it with the Asus SLIx16 mobo, the A8N32-Sli. Problem with using that motherboard is that the card only worked properly on the bottom PCIe socket (furthest from the CPU) - when using it in the top PCIe socket, only one of the two GPUs registered in Device Manager.
I figured I'd switch over to the K8N Diamond Plus and see if that works better (I'm only considering SLIx16 mobos, as my plan is to get another of these cards later on and experiment with Quad GPUs, hence the need for the extra PCI lanes) - has anyone tried this motherboard with the Asus card?

Quote from: pibrahim on 25-January-06, 21:46:50
That's very odd, that MSI boards work so differently from Asus.
Problem is that the dual-GPU card won't work properly in the top slot and I really needed it to be in the bottom. Not sure what exactly I can do about that now...
Toms hardware did a review on this.
The card shows up in the primary slot as 1 gpu, then you add a second card it shows up as a 3 gpu system. THe first card says 1 gpu, but operates as a two gpu.
Look up the card on new egg, there is a link to the reviews of it some where in there.

K8N Diamond Plus microphone not working

Similar Messages

Maybe you are looking for