K8n msi motherboard will not enter bios

Ok here is the hardware in the case at the moment
K8n mobo (neo plat)
3000 64 CPU
ati rage 128b (test only tried a700)
1GB Crucual Ram
Antec True Power 380W
All I get is five short beeps, I have reset cmos and still nothing
Please help me :(
If you need more info I'll post it

Quote from: workknot on 04-January-06, 11:08:29
It would be a good idea to post a signature with all of your equipment listed. It could be you are a little short on power, what is the voltage on the 12 volt rails of your power supply?
Pop's
The Psu is an antec 380W
These are the readings
for the 12v rail its 24A if thats what you needed
The beeps may well have been down to the fancy case, a bog standard case gives me NO BEEPS
If I keep in the memory, video card and cpu with HSF the system shuts down after around 15 secs
If I take out the memory and remove CPU the system stays on but no beeps, no boot

Similar Messages

Will not enter bios setup

Every time i hit the F1 key on my HP Pavilion 7965 Desktop I get the HP screen and at the bottom of it, the message "Entering SETUP". However that is as far as it goes. It just seems to freeze and does not enter setup. Does any one knows why and how I can get it to finish entering setup?

Hello darkfant,
Pressing F11 on startup should enter the Advanced BIOS. If you press F11 on boot up does it do the same thing or is it just tied to the normal BIOS?
If I have helped you in any way click the Kudos button to say Thanks.
The community works together, click Accept as Solution on the post that solves your issue for other members of the community to benefit from the solution.
- Friendship is magical.

Satellite L305D-S59222 Will not enter BIOS

Okay, in an attempt to fix the OS and not having a cd, I used my flash drive (which has windows on it) as a boot drive. However, as soon as I told the computer to boot up after setting bios to boot to usb device, it looks for PXE. I know this means it is looking for a network to boot from. So I attempted to re enter bios and check what was going on, and possibly disable network boot. It freezes up on the toshiba flash page.
I have removed hd, cd drive, flash drive and ram (which incidentally won't let me even get to the toshiba flash screen).
Any other suggestions?

Satellite L305D-S59222
You might try reflashing the BIOS.
ACPI Flash BIOS version 1.80 for Satellite/SatPro L305D/L355D PSLC8/C9/CJ/E8
-Jerry

IPod Help needed from serious Apple gurus - iPod Touch 2g 16g stuck in restart loop. Will NOT enter DFU or recovery mode, NOT recognized by iTunes on Windows or Mac

Ok, so here's the not so sad story. I bought an iPod Touch 2g 16g through Ebay - so forget warranties. Luckily I did not pay much. The description said it was stuck on the apple logo, so I figured it would be an easy put into recovery mode and restore problem.
Not so much.
If you plug the iPod in and charge up the battery the LCD will come to life after a while with the apple logo, then it displays the spinning wheel with the apple logo over it. That will last anywhere from 10 - 15 minutes, then the iPod will go blank for a few secs and then start up the cycle all over again.
As stated, this iPod will NOT enter either DFU or recovery mode and believe me I've tried it several times several different ways with different timings, connected via USB to a Mac, connected to a different Mac running Windows, and connected to just the charger. Nothing. Occasionally the screen might go blank while holding the power and home buttons but nothing else happens and then it starts it's usual cycle again.
Again, iPod NOT recognized by iTunes on either Mac or Windows side. Since I got off Ebay and seller didn't know much about it, I have no idea if someone tried to jailbreak this or not.
I will not put much money into this machine. So I guess my question is: does this behavior mean that the motherboard is clearly fried? Are there any software programs that might diagnose what the problem is? Could it be as simple as a fried battery?
And most importantly, is this iPod simply toast or is there anything anyone can suggest????
Really any suggestions would be greatly greatly appreciated. Seems a shame to just trash an iPod touch that might need a simple fix...
If it helps matters, I can tinker with iPods somewhat and have torn down and replaced several iPod touch 1g and 2g glass and digitizers with no problems. I'm somewhat software savvy but the whole jailbreak thing is new territory... and I can't really figure out the command in Windows or Mac terminals to list all connected devices so I have no idea if the computer even knows the iPod is there, even if iTunes doesn't. Guess that's it... ummm, please help???

Nothing huh? No one's had this problem or this isn't fixable... oh well... if anybody comes up with anything I'll check in occasionally...

Bootcamp windows 8 will not enter safe mode

My bootcamp windows 8 will not enter safe mode. I've tried press Fn + F8 multiple times.

http://windows.microsoft.com/en-US/windows-8/windows-startup-settings-including- safe-mode

Disc will not enter - how can I fix problem?

Disc will not enter. Feels rubbery when disc is pushed into slot. Can this be fixed without technician?

1. Try and delete stalled Podcast
2. Sign out of Apple ID>Reboot>Sign in again

My iPad air is disabled because I endeterd the wong keycode and now and will not enter recovery mode

My iPad air is disabled because I endeterd the wong keycode too many times and now and will not enter recovery mode. I haven't a clue what to do next?

Follow the steps in this Apple support page.
Forgot passcode for your iPhone, iPad, or iPod touch, or your device is disabled - Apple Support
If you must use Recovery Mode, which is at the bottom of the linked page, follow all steps very carefully. Even hen you might have to try several times.

3 ea MSI K8N Diamond Plus will not POST

I have 3 K8N Diamond Plus motherboards that recently started having intermittent problems POSTing to BIOS. I initially found it possible to boot by clearing CMOS and reentering my settings; however, over time these boards have gotten to where they will not POST at all. Power comes up, but the four-LED diagnostic display stays continuously red, indicating no BIOS activity. Ideally, I'd like to get my hands on a service manual for this board, but if anyone can throw out common issues with this board as a starting point, that would be great. All of these boards have been in service for more than 3 years in 3 different machines. The failure appears to have identical symptoms. I would bet the component that has failed is common to all 3 boards. It seems other people are having the very same problem with these boards over several years of service. I have tried all of the usual troubleshooting tactics with no success. Thanks!

Check for bulging, leaking, ruptured capacitors near CPU socket.

Motherboard will not boot up@133

I have recently built a system with an MSI KT4V-L motherboard, 512 PC2700 Ram, Athlon 2GH Chip, the system works fine with the FSB set at 100MHz, as soon as the system is set to 133MHz then the system will not boot to either windows or a boot disk, is this a problem with the motherboard or a conflict with the ram modules

Hi,
Has this board got a jumper to toggle 100/133 - if it has you need to set it to 133 and also - set the clock frequency in the BIOS to 133.
Forgive me if I'm stating the obvious - but you never know.
Axel :D

Msi 6511 will not boot

I received an msi 6511 and it will not boot, I only get a light on the floppy but I can not tell if the other leds are on because they are not hooked up (I do not have the manual to this board)!! The specs are
1.2 GHz amd athelon
384 mb pc100 sdram
onboard sound
onboard video
450 watt psu
Any help would be much appreciated!

Hi
Your athlon could either have a 100 fsb or a 133, they came both ways. If it is one with a 133fsb then the memory (PC100) is not fast enough to let it boot. Set jumper J6 to pins 2-3 for a 100mhz fsb so that the cpu fsb will match the memory.
See attached link for jumper settings if you don't have the manual. This appears to have been an oem motherboard used by packard bell among others.
http://www.uktsupport.co.uk/pb/mb/explorer.htm

MSI R5750 Will not display during boot, crashes on update

Hello,
I recently upgraded my PSU and VGA for my computer and am using a generic LCD monitor (hp L1925). When I installed the VGA, it will not send any video output unless the monitor is first plugged into the motherboard's video. When I plug the monitor into the VGA, everything runs fine, the VGA works well. However, when I try to either install or uninstall drivers, part of the monitor turns black and then loses picture. Live Update has my system at the latest version of BIOS for both the motherboard and VGA. Any ideas?

I swapped out the video cable between the monitor and the vga, now everything is working very well. Thanks.

New motherboard will not work

I had a MSI 6507 motherboard go bad..
I purchased a new msi p4mam motherboard, installed it and the computer will not post.
Is there something maybe we forgot to do???
Follow all the instructions
Any help would be appreciated. This is the kids computer and they are really wanting to get back to their games .

The 4-pin is connected
I have reseated the processor
I have tried one stick of , even tried new ram
cleared Cmos
Even tried a differnet procesor that we knew worked out of a different machine.
I had Windows XP
When I start the computer the green light on the box comes on, the fans spin teh light for the CD flashes but nothing els. NO beep, no display.. could I have connected something wrong? I am at a loss.....

Not entering BIOS

My notebook HP 4530s is not entering in bios. After i turned on the legacy boot option from the menu. whenever I pressed the F10 button it brings up the System Diagnostic screen and I have an all the tests but still nothing.
I had removed all partition from the hard drive and I was facing with issue where windows 8 setup was not installing it on my hard drive.
After reading on internet I turned on the Legacy boot mode and now I am stuck .... Any help?
This question was solved.
View Solution.

There is not an major problm this will cause due to UEFI system and/ GPT disk partition
here you have to follow these steps
1) firs of all turn off your notebook.
2) press power button and then immediately press esc button and look at left bottom of screen you will see pause system startup or similer.
3) Then you will see list of commands on top left corner like system recovery , boot menu, bios etc depend on your model then choose bios option now you have opened your bios
If you dont see command list or system will boot OS then try this steps again
If your problem is not solved after following this steps please reply.I will give you another solution

T61 New hard drive will not boot, BIOS doesn't reckognize.....

Ok i need some major help here. I recieved a new Seagate 500Gig internal hard drive for my lappy. so i thought i would do a fresh install of windows vista, via the restore media that i created from the thinkvantage software on my laptop.
Now here is where the problem lies....Before I install it, format it or write any data to it, BIOS reads the new drive just fine. As soon as i run the recovery software cds i get a verry anoying error.
The following is the exact error message.
"error 2100: HDD0 Initialization error (1)"
Has anyone else seen this and been able to install a new hardrive in this laptop?
Weird thing is this. I put the old HD back in 100GIG and connect the new one, that BIOS won't read after data has been written to it, to an external USB case.
I load windows vista just fine off my old drive, plug in the now 500G external drive and windows reads the data that has been written to it from the restore CDs.
Can anyone help me out here. I have spent the past 2 full days trying to figure this out.
Thanks

Ok just as an update thus far. i still can't get it to read the hd after i install from the recovery discs...which is odd of course.
It does read the drive before i install anything to it though.
OK time to add something really really weird though, i an attempt to figure this out, i installed the 500G drive and put ubuntu on it just to see if the problem was w/ the HD having a failure or not.
ubuntu installed just fine, and i am typing this off the installed ubuntu OS.
SO now i have to ask, is there a bug in the recovery cds that thinkvantage has us create? is there a way to test that?
Does the t61 have a limitation w/ a 500GIG hard drive that will not let the recovery dvds work or install properly?

Msi object will not install with non-admin user

I've created an MSI object for the Flash 9 plugin, which installs okay
on the workstation when I login with an admin user. It will not
install when logged in with a normal user account. I have set it up as
an unsecure user and given the workstation R and F rights to the msi
object, but I'm still getting a 1603 error code.
Any suggestions?

http://appdeploy.com/packages/detail.asp?id=798
You will see the ZENworks reference on this page.
I would bookmark this site :>
I almost always check it before deploying a new package to see if it is
listed. Helps me find issues before the issues find me :>
[email protected] wrote:
> I've created an MSI object for the Flash 9 plugin, which installs okay
> on the workstation when I login with an admin user. It will not
> install when logged in with a normal user account. I have set it up as
>
> an unsecure user and given the workstation R and F rights to the msi
> object, but I'm still getting a 1603 error code.
>
> Any suggestions?
>
Craig Wilson
Novell Product Support Forum Sysop
Master CNE, MCSE 2003, CCN

K8n msi motherboard will not enter bios

Similar Messages

Maybe you are looking for