K8N Neo 2 platinum memory problems

Ok to start off I'm trying to run 4 512's corsair xms 3200 on the mother board MS-7025 but problem is if I try and run at 2 gig my PC will not boot up the monitor light stays on amber or in a sleep mode.
But if I run just 1 gig it boots up fine the ram is fine and tested also tried swapping the ram into diffrent slots and it works just not with 2 gig.
I have used the manual and unplugged the ATX power cable and jp1 power before i put the ram in but still no luck
could it be a bios problem or hardware I'm not sure any help would be greatly appreciated

Quote from: jimbojim on 01-December-06, 07:03:26
I have tried setting the memory voltage at 2.7 and still no luck thanks for ur time
it is not good solution to use 4 sticks at all. read here: https://forum-en.msi.com/index.php?topic=103090.0
is all mem. sticks are identical? can they works separately by 2 sets (2 mem. sticks per set) with same settings?
setup memory limit to 333Mhz, apply command rate to 2T too, bump mem. vcore to 2.75V. apply basic memory timings manually and ensure its acceptable for all four memory sticks.(cas,trcd,trp,tras) other memory settings leave it to auto.
re-test and post back results.

Similar Messages

Please help! K8N Neo 2 Platinum instability problems

Hi!
At the fall of last year I bought new computer parts for a new system, the heart of it being a MSI K8N Neo 2 Platinum. Ever since then I have had some instability problems. I tried for a while to fix them, but after a while lost the energy and have just accepted them. Now, however, I want to give this forum a try for help. The instability is irritating and I've been thinking of returning the motherboard.
The system consists of:
MSI K8N Neo 2 Platinum
2 x 512 MB Kingston Hyper X PC3200
AMD Athlon 64 3200+
Gainward Geforce 6600GT AGP
Trust 514DX 5.1 Sound Expert Optical
120 GB Seagate SATA HD
NEC DVD-RW ND 2510A
Zalman ZM400A-APF PSU
Nothing is overclocked. I also have a Terratec TV-card that I never use.
I'm running Windows 2000. I have the latest BIOS, 1.C. I have tried many different Nforce drivers, right now I'm running MEI's nWare Release 06.05a.
The driver for the GPU is 91.28. Every other driver should be the latest there is.
The problem I have is that the system freezes up in Windows now and then. The "funny" thing is that I can run Memtest 86 for a whole day, Windows memory diagnostic all the way trough and I can play games (most of the time) for hours. I have also had the computer doing video compression for days and days, so I would say that it seems kind of rock solid. The freezes seems to happen (I'm guessing) when there is lots of communication going on over the southbridge. It often happens when the HD is working and the CPU perhaps get loaded at the same time, or for example if I'm ripping data from a DVD and starts doing something CPU heavy at the same time. That is an almost guaranteed recipe for freezing. Sometimes it freezes when I'm doing "nothing", but I guess it might also be when Windows is swapping, or something.
I remember reading about problems like this before, with other motherboards. I'm thinking that perhaps some BIOS latency thing could fix it. Perhaps a hacked/tweaked BIOS? Or is the motherboard in fact busted and needs to be returned?
Any thoughts, ideas or tips are welcome. Please help!
Thanks in advance!

. . . I'd half to agree 100% on what BAS is pointing out . . . . . . . .
........also, for kakarocht's reply for the matter as well....
.....{ my opinion = 450w at least of a PSU, and, >>> what BAS is stating about's the 12v line, YES, BIG requirement for your system's _ component's of } .......
mr. Charles
.

Neo 2 Platinum Memory Problem

Hi There,
i have here two PQI DDR400 PC3200 512MB dual-sided, one crusial DDR400 PC3200 512MB one-sided and one crusial DDR400 PC3200 1024MB dual-sided.
Here's the problem:
When i install all the four modules my computer wont bootup it will only give one long beep inducating that there is a memory problem. All four modules where tested separetly with no problems. I have now only the two crusial modules on my Neo 2 Platinum running with no problems.
Can some one help me so i can use all four modules please???????

Assuming they will all work together, it sounds like the BIOS isn't set up properly, or the board isn't detecting the speed correctly. When installing more than 2 dimms, most boards, due to the memory controller on the CPU, will set the RAM to the 166 divider, or DDR333. Generally it will also set them to the 2T command rate.
If you have a Winchester core you will more than likely need to run DDR333 with the 2T setting. On a Venice you may be able to get away with DDR400...I know on an Opteron you can do DDR400 with the 2T command rate easy enough...I will assume it is probably the same with the newer cores as well.
Again, IF they all work together (mixing and matching dimms may not always work), you may just need to set the BIOS up properly. Pop in the sticks that work, go into the BIOS and set the RAM to the 166 divider, and then make sure the command rate is on 2T. Be sure all the RAM can run the timings that are set in the BIOS. Save and exit. Then power down and unplug the PC, pop in the other stick and see what happens.
If that doesn't work, you can try different slots, or an even a lower RAM divider (probably won't make a difference). IMO, if all the settings are correct and it still won't work, I would guess that mixing the RAM is the problem. I have seen it happen - I have also had weird RAM configs work perfectly, so it is kind of hit or miss...I hope some of that helps, good luck.

K8N Neo 2 Platinum: having problems formatting NEW SEAGATE 200 GB SATA Drive.

Ok..
I can see the SATA drive during Windows Installation and in Windows XP... but I can't format it.
It freezes up at 20% when I do quick format.. and when I did a normal format it Windows gave me a error saying something about drive may be damage or installed wrong..
Right now I'm running IDE0 Master (Western Digital 200 GB HD) IDE1 Master (Toshiba DVDROM), then the Seagate drive in SATA0.
I see the drive in bios, windows, and windows install...
I've disconnecting my ide drive completly & disabled ide in bios... still won't format properly
i've also tried the f6 and loaded the 'nforce 3 SATA RAID Driver' disc that came with the motherboard and it still froze..
right now i am on my normal bootup (ide wd hd), windows xp detects the hard drive in windows.. i see it in disk management.. i can delete/make partitions.. but i just can't format it.. gaaaaaaah
any help would be much appreciated.

Quote
Originally posted by cfeedback
In years past I was able to install XP w/o a SP on a large drive without any problems. The process I believe I had to take was use the manufacturer's utility to format (in this case MaxBlast from Maxtor) the drive, install Windows, immediately install SP1, and then enable 48-bit LBA via the utility (you can find a .reg file that will enable it as well). While I wouldn't recommend it I never had any problems.
Ah, you just got lucky that Windows didn't try to write something past the 137 GB point. I've always known about this, but coincidentally, this just happened to me the other day where Windows told me I had a 200 GB (186 GB really) installed and ready to go, but then a few days later I kept getting a ton of "Write Delayed" errors. I was so distracted at the time (with other issues), that it didn't occur to me what the problem was, and I ended up losing a lot of data.
Anyway, for anyone really interested in the full scoop, you can read about here in Microsoft's knowlege base.

MOVED: K8N Neo 4 Platinum Boot problem

This topic has been moved to AMD64 nVidia Based board.
https://forum-en.msi.com/index.php?topic=110171.0

Ups, I messed up. Thanks for moving this to the correct forum!
Yes, I'm using 1st Dimm slot. I cleared CMOS with and without the power cord, with and without the battery, and every way possible. I even held the button down for 2 minutes.
PSU is Vitsuba 450W. The 12V rail has 20A.
I don't have a better PSU. Should I buy one?
Already tried barebone setup. Just didn't know what it was called. Reseated CPU but didn't change anything. There are no bent pins.
How this happened. I was working in windows and it BSOD. I reset and it didn't boot at first time, but after several tries it finally booted. That was last week. The problem repeated once again yesterday, so I decided to do a clean reinstall of Windows, just in case. So I had some troubles to boot again but it booted ok after some time. Installed windows, drivers, updates, apps, etc and everything was fine. I switched off the system yesterday at night. Today the pc won't boot anymore. So, here I am!
Thanks for your assistance and don't hesitate to ask me some more questions!

K8n Neo 2 Platinum Board Booting issues

# CPU brand, model and speed (E.G. AMD Athlon64 3000+ 'Venice' core) AMD 3800+ Not sure of Core
# Motherboard model (E.G. K7N2 Delta2 Platinum, NOT just MS-6570!!) K8N Neo 2 Platinum
# Memory brand, type/speed, size, number of sticks (E.G. 2x Crucial 512MB DDR400) Kingston KVR400x64c3a/512 x2
# Video card brand, chipset type, memory size (E.G. Gainward Geforce 6800GS 512MB AGP) ATI Radeon 850 Pro 256MB AGP
# Hard drive(s) brand, size, type, speed (E.G. 2x Seagate 200GB SATA150) 2x Hitachi 80GB SATA150
# Any other peripheral cards and devices (E.G. MSI TV@nywhere Plus TV card, MSI DigiVOX USB2 TV tuner) D-Bracket 2
# Operating system and version (E.G. Microsoft Windows XP Home Edition SP2) Windows XP Sp2 / Ubuntu 7.10 / Vista Ultimate
# Power Supply Unit brand and output in watts and DC output (amps) TurboCool 510 ATC-PFC ( Taken from a Vapochill SE Chassis ) Originally had been Tagan TG480-U01 however it just blips the power on and off so thinking it is faulty.
I have replaced my motherboard as I had thought it originally was a duff BIOS chip as despite reflashing it, it would rarely pass the POST.
All parts apart from the PSU are the original Kit which had been working for 13 months ish.
Problem i am experiencing is the D-Bracket 2 Diagnostic LEDs are coming up Red/Amber as opposed to Red/Green and the machine just sits there and never displays anything, hence why BIOS isn't mentioned as I have no idea what version is currently on the BIOS chip.
I have stripped out down to just CPU and still get the same problem, I then swapped it for a FX53 which I had lying around which I know worked as it came out of my Vapochill chassis and also swapped out for some OCZ PC3700 512MB EB Dual Channel Platinum 3-3-2-8.. still no joy.
Any ideas greatly appreciated as I don't want to rebuild my machine as it is exactly how I wanted it I feel I have checked everything but maybe someone can shed a little light.
Anyone want a spare mboard or two ?? I now have three !

Your Tagan's behavior was typical of a failing PSU... but the Turb-Cool model you mention doesn't exist at the PCP&C web site; in fact there are a total of five other 510 models, some of which have only an 8-pin CPU power connector, so it's impossible to figure which one you have. Does your PSU have a 4- or 8-pin CPU power connector and, if the latter, how do you have it connected to the mbrd? The only 8-pin CPU power connector I've seen could not be connected to a 4-pin socket, which your mbrd has... or does your mbrd have both 4- and 8-pin?
The only other thing I'd remark is that Vista will not run satisfactorily with your nForce3 mbrd and an ATI video card.

Boot Problem with K8n Neo 2 Platinum

I cant get my Computer to load the bios
Sometimes when I restart my computer it will lock up in the Bios Sign on and the only way to get it to boot through is to keep resetting the computer and turning the power off and on. It does this on a random basis, Ive also had problems with it locking up if the dynamic oc is turned on.
Has anybody heard of this happening or know how to fix it?
MSI K8N Neo 2 Platinum Bios 1.4
Athlon64 3800+
TwinX 1024 3200LLPRO
Xtasy 9600XT
Ultra Products X-Connect 500w
2x WD Raptor 10,000rpm SATA HD in Raid 0 cfg
SB audigy 2 ZS
LiteOn cd/dvd drive
LiteOn dvd burner
Windows XP SP2

Corsair memory is known to be troublesome with AMD64.
Nevertheless, if everything is set correctly, it'll work. I've been running the LLPRO 3200 1GB kit at 220MHz without any noticable problems. Run a couple of rounds with Memtest86+ to verify memory functionality.
Can you please give your specifications on the power supply unit (PSU), especially the amperage on the +12 volt rail.
Anders.

Problem with K8N Neo 4 Platinum

Hi I am new on this forum.
I have problem with proper configuration of the BIOS in K8N Neo 4 Platinum. My processor is Athlon 64 3000. It has 1800 clock. My BIOS makes default 200MHz x 5. It makes 1000 MHz clock. Will it be good if I change at 200 x 9?
Other thing: I tried to change at 200 x 9 but in Windows (2000) is still 200 x 5 (acc. to Core Cell). When I chanded on 200 x 7,5 all in Windows was ok. Core Cell showed 200 x 7,5. How I may resolve this problem?

Quote
I have my memory in green slots. Does dual channel works in this case?
- No Green = Channel A, Purple =Chanel B use Green nearest cpu & adjacent purple slot.
Quote
HT freq. 5x
That's your HT multiplier as mentioned by Some1ne not the Adjust CPU Ratio which is the CPU multiplier.
Your CPU is running at the correct speed.
DDR Clock: 167 MHz s/be 200 - this should chnge when memory is in right slots.
Change memory over & let's have a look @ those settings then.
luck

MOVED: MSI K8N Neo 2 Platinum Problem

This topic has been moved to Overclockers & Modding Corner.
MSI K8N Neo 2 Platinum Problem

A lot of things could be wrong but it will be easier to figure out if we know what you did. When you say you changed settings in Bios, do you remember your last settings and what you did?
It might be helpful if you created a sig (as described in the forum rules) to show what you have in your system like my sig below. (Hint- use profile button in sign on screen.)
Things could be broken even if there is no visible evidence (such as flames or melted component) of course.
If I had to guess and your d-bracket reading is correct, corrupted bios requiring new bios chip, but let's not guess as a lot of things could be wrong and you don't want to invest in a new bios chip if the board cannot be brought back to life. Consider removing parts and testing them in an other machine. Start with CPU and memory?
Good luck.

K8N Neo 2 Platinum - installing xp problem

Ok guys i just installed a new K8N neo 2 platinum with a 3200+ s939 chip. Now i ran off the xp cd and i told it to format as ntfs, it did that fine and dandy. Now after that it starts to copy windows xp files and it does that fine, now it comes to the point where it has to restart for the first time. So i restart and after i let it go past the part where it says "Hit any key to boot off cdrom" or whatever, then it comes to booting off the harddrive and it says "operating system not found"

Quote
Could the difference be because you have the neo and RC1 whereas I have the neo2 (1.4 BIOS) and RC2?
Don't think so most likely difference between destination drives, yours is a sports car, fast when it's running but quircky, mine's a transit van works even when old & abused.
Have you checked Western Digital Jumper Settings Pata & Sata even new drives have been known to have been jumpered wrongly.
Onlly other maybe relevent thing I burned my iso at x8 to try & maximise cd quality, have seen a few pps with xp64 cds they couldn't boot from on the ms 64 newsgroup. Don't know if your cd may have been slightly screwed if thats the echnical word for it

K8n neo 2 platinum corsair xlpro troubles

New to the forum so forgive me if I make any mistakes.
Ive been trying to find some info on the k8n neo 2 platinum, but I havent found anything related to my problem, only some info on the k8n neo.
The problem is that I have a 1 gig dual channel corsair xlpro kit, when installed in dual channel mode the computer wont boot, absolutely nothing happens.
Tried single channel mode and that works fine, both modules run at cas timinngs of 2-2-2-5 at 200 mhz (ddr400).
Ive tried turning up the voltage to 2.7 and 2.8, tried booting with more relaxed timings, but again the system just wont boot when using dual channel .
Tried some corsair twinx xms c2pro memory but same problem, wouldnt boot.
even set everything on auto but that didnt help either anyone else having this problem or am I the only one and if anyone solved it plz plz plz tell me.
Thnx

I have 2x512 of Corsair TwinX PC3200XL and both work fine on my 754 Neo at their rated timings.
Though my setup is only single channel and proves atleast the Corsair is compatible with our boards.
Unless you can test another 1gig of ram your in a tough bind as its very possible your chip is defective, obviously having the dual memory controller built in.
goodluck

Buying a K8N Neo 4 Platinum mobo - need some answers

Hi,
First post here, so I should say I did a search and did actually read the stickys.
Like I said, I'm getting the MSI K8N Neo 4 Platinum and need to know:
1. Does it support NCQ?
2. Can I use "PDP SYSTEMS Memory Dual Channel Kit 184-Pin 1GB (512MBx2) DDR PC-3200, Model PDC1G3200LLK" with it?
(And have it working @ 2-3-2-5-T1 Dual Channel like it should without OC)
2.1 Can I use 4 dimms of this memory without going down to 333mhz?
3. I'll also get a 6600GT, DVD-RAM,DVD-ROM, 200GB HD - which PSU I should go with?
I wanted to get a TT410W, but heard I should go with "Enermax 350W EG365P-VE FMA 20/24Pin Power Supply" because it gives higher 12V rail power.
I dont plan on doing OC
Thanks in advance for your answers, and sorry about my english.

Quote from: kctay on 10-March-05, 02:14:51
Chrisss,
I think that Tiresmoke's point is that your statements aren't productive, I don't see a history of you trying to ask any of the well versed vetrans here for any help regarding the stability of your system, or inherent problems with the mobo in question. You also don't even list the components that make up your system in your signature which might allow someone to help you without you even asking a valid question.
Statements like this; "I have so many stability issues it's not even funny. I have not overvlocked anything and the PC crashes randomly." simply aren't meaningful without knowing the pertenent facst surrounding your issues. Furthermore, the problems you have may have nothing whatsoever to do with the motherboard.
Sixth, this is a good motherboard for your stated needs, I run the SLI version and have nothing but positive things to say about it. I did extensive research before buying this product, and it really paid off, this is a great motherboard.
Actually yes i did ask: https://forum-en.msi.com/index.php?topic=75700.0 But only one person helped me. It could be that the SLI version is more stable. Just read the posts. there are a lot of people with issues with the K8N Neo4 Platinum. Not too many with the SLI. So it's not only me.

MOVED: Looking for feedback on K8N Neo NF4 Platinum SLI, LUV THIS BOARD

This topic has been moved to Overclockers & Modding Corner.
Looking for feedback on K8N Neo NF4 Platinum SLI, LUV THIS BOARD

Im no pro but with your raid setup you need to stay with bios 3.0, 3.1 or 3.2. I understand that 3.3 & 3.4 causes problems but the new 3.53 beta bios fixes the problems in 3.3 & 3.4. See below:
https://forum-en.msi.com/index.php?topic=80933.120
Regarding your pcie clock, if you are using coolbits and nvidia drivers only (no MSI drivers at all), then I have used nvidia's ntune to help set the clock. For my x1 msi 6600gt, working backwards from the bus speed optimization it equalled to 106...but I am really not good at this and you should post your question under the VGA portion of this forum for a better answer to that 1 question.
However, using MSI's DOT works well too and its automated.
Btw, the pcie setting has nothing to do with your cpu/memory overclock.

K8N Neo 4 Platinum Questions...

I'm going to be upgrading to a 7800GTX soon and will have to replace my mobo which is a K8N Neo 2 Platinum. I am currently using an Antec True 550 ps, which has 30 amps on the 12v rail. However, it is only a single rail ps and it has a 20 pin connecter. I plan on upgrading to a K8N Neo 4 board and was wondering if my ps is still okay even though it's only a single rail. I read the sticky and it seemed to suggest that single rail was still preferable but I just wanted to make sure I wasn't mis-reading anything. Secondly, does the K8N Neo 4 use a 20 or 24 pin header? If it uses the 24 pin will I be okay using my current ps which is only a 20 pin? Moreover, would I be advised to purchase a 20->24 pin adapter or should I just plug the 20 pin into it's corresponding pins?
The rest of my system:
Winchester 3500+
DVD burner
CD burner
OCZ 2 GB (2x1024) Platinum DDR 400 memory
Haupaugge PVR 250
WD 160 GB SATA HD
Thanks for any advice

K8N Neo4 Platinum has compatibility issues with nVidia 7800 cards. There is a capacitor very close to the PCI slot which makes the installation impossible. You may search the forum for more info.
Your PSU is OK as long as you won't be overclocking as your card consumes a lot of juice/I'd still go for more Ampers on the 12V rail/. It's not really a problem whether you have 1 or 2 12V rails....The mobo uses 24pin header but 20 is OK as well....You don't need an adaptor for that.

K8N Neo 2 Platinum Computer just...stopped working! Help needed please.

Hey all. About hmm, a month ago I built myself a new PC (first time I'd done it from scratch and got some useful help here) Specs were:
MSI K8N Neo 2 Platinum, A64 3200+ Venice, 1GB DDR Corsair Value, Radeon 9800 Pro 128mb, 40GB Hard Disk IDE, 80GB Hard Disk IDE, CD R/RW Drive and a Tagan 420W (23A 12V+) PSU.
Ok, it worked the day I built it just fine and has NO hick-ups or any indication of a problem for the past month. Running temperature was very cool etc. Now, I last turned it on about 24 hrs ago, downloaded some PDF files, shut it down. All was fine. Woke up this morning. Pressed the power button: ABSOLUTELY NOTHING. ZIp. No hum, fan movement, anything.
Now, considering it seems to have broken whilst being turned off. What could be the problem? So far I've tried:
* Using a different power socket
* Using a different plug
* Reconnecting the power switch and motherboard power connectors
None of those worked. There wasn't a thunderstorm or anything so I don't think any kind of surge would have been the problem. I havn't tried manually shorting the power switch connectors. What's a safe way to do that? Any other suggestions? How can I test my PSU is infact doing something?
Thanks

Quote from: go_for on 01-September-05, 21:47:40
Try the easy way first, disconnect every cable from the back of the computer. Do a CMOS clear/normal as instructed in the manual. Connect the display(with power off), keyboard and power cable. Turn on PSU, press power switch, if it fires up, press and go into bios and do your settings, save and exit. Power off and connect the rest of your external stuff. Power up.
>
No luck :( Is it likely that my PSU has fused/broken in some way since I'm getting no response or fan movement?

K8N Neo 2 platinum memory problems

Similar Messages

Maybe you are looking for