K8N Neo fails to boot with more than one DIMM

I have been searching the forums for a while now, and will continue, but I am really hoping for a quick resolution.  My system was running fine for over a year with a pair of PC3200 512MB DIMMs.  I normally leave my computer on all the time.  Recently I updated my BIOS to 2.10, and the system performed a soft boot afterwards.  Christmas Eve day I knew I was going to be gone the whole day and probably not need my computer until late on Christmas day.  I received a very unpleasant surprise.
I attempted to boot the computer up, and I got nothing but a repeating single long beep.  I did a lot of troubleshooting and discovered that the system will boot and run fine with ONE DIMM, either DIMM.  My system will no longer boot with a second DIMM in either the 2 or 3 DIMM slots.  This is a major bummer for me, please help.
I have not played around much with memory timings and such as of yet.  It is quite a pain to put in a single DIMM, and boot the system to make a BIOS change then shut it down again and install the second DIMM to see if it works.
Thanks in advance for any help.
Scott

Go back to your previous BIOS.

Similar Messages

  • PC will no longer boot with more than one stick of ram.

    Hello.
    My wife and I both own HPE 371f. We've had them about 8 months and neither one of us has had a single problem with it.
    Yesterday though, I got a BSOD. I try to reboot, it goes in to recovery mode and freezes. I try to reboot again, same thing. It freezes up as the windows logo is on the screen. I start scouring the web to find out what could be the problem. All the fans are running, mobo looks to be okay, HDD is fine. I finally see the suggestion to update the BIOS. I can't even update now because I'm getting a blank screen. I turn the PC on and it just looks like nothing is getting to the monitor.
    So I try a CMOS reset. I'm able to get the PC to the boot menu at least, but now it freezes up in the boot menu.
    At my wits end, I finally see a something about RAM timing being off or something (I'm not very experienced with this) and they suggest taking out all but one stick of ram. I do this, and lo and behold I boot up fine. Every configuration of more than one stick of ram I try does not work. Any more than 2 gigs... and all I get is a black screen.
    It's not a major deal being down to 2 from 8, but I would like to use the RAM is possible. Is this a hardware issue or something I can fix through software?
    Some notes: No major changes over the last few days. I installed Skyrim, but I wasn't playing when I got the initial BSOD. I've had 4 sticks of 2 gigs since I bought the PC and I've never had an issued till now. All the sticks are identical. My wife's PC (same model) is working just fine.
    Thanks in advance for any help or ideas!

    Hi,
    I've been searching the internet and people are talking about updating BIOS to play Skyrim. It's worth a try. Please go to this site to (a) Select your machine (b) Pick the right Operating system. Download BIOS and apply to your machine. Hope this helps, otherwise please contact HP for help (is machine still under warranty ?).
    Regards,
    BH
    **Click the KUDOS thumb up on the left to say 'Thanks'**
    Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

  • Updating JournalEntries object with more than one currency fails

    I'm using SBO 6.50 (exactly CEE version 7.60.014 SP:01 EF:08).
       I'm trying to update memo field of existing journal entries. Most of them works OK, but if I try to update entry with more than one currency, update fails with an error code -5002 and message:
       Transaction includes more than one currency [OCRN].
    Code (in C++) is quite simple:
    SAPbobsCOM::ICompanyPtr m_company = SAPbobsCOM::ICompanyPtr("SAPbobsCOM.Company");
    SAPbobsCOM::IJournalEntriesPtr pEntry = m_company->GetBusinessObject(SAPbobsCOM::oJournalEntries);
    long m_nId = 1;     // TransId field, any valid value
    try
         if (pEntry->GetByKey(m_nId) != -1)
              return;
         pEntry->Memo = _bstr_t("Memo");;
         if (pEntry->Update() < S_OK)
              throw(0);
    catch(...)
         long lError; BSTR bstrError;
         m_company->GetLastError(&lError, &bstrError);
    What's wrong? Using multiple currencies in journal entry is correct, it is possible to add them manually so it should be possible to update such an "safe" field as Memo is.

    Hi,
    I have the same problem, but if you go to Administration->System Initialization ->Document Settings, select "Per Document", and in Document, choose "Journal Entry", by default, the options are clicked, or "Blocked", this is why in DI yoy get this message.
    Try to unchecked and it will work.
    HTH,
    Ribeiro Santos

  • Error while running spatial queries on a table with more than one geometry.

    Hello,
    I'm using GeoServer with Oracle Spatial database, and this is a second time I run into some problems because we use tables with more than one geometry.
    When GeoServer renders objects with more than one geometry on the map, it creates a query where it asks for objects which one of the two geometries interacts with the query window. This type of query always fails with "End of TNS data channel" error.
    We are running Oracle Standard 11.1.0.7.0.
    Here is a small script to demonstrate the error. Could anyone confirm that they also have this type of error? Or suggest a fix?
    What this script does:
    1. Create table object1 with two geometry columns, geom1, geom2.
    2. Create metadata (projected coordinate system).
    3. Insert a row.
    4. Create spacial indices on both columns.
    5. Run a SDO_RELATE query on one column. Everything is fine.
    6. Run a SDO_RELATE query on both columns. ERROR: "End of TNS data channel"
    7. Clean.
    CREATE TABLE object1
    id NUMBER PRIMARY KEY,
    geom1 SDO_GEOMETRY,
    geom2 SDO_GEOMETRY
    INSERT INTO user_sdo_geom_metadata (table_name, column_name, srid, diminfo)
    VALUES
    'OBJECT1',
    'GEOM1',
    2180,
    SDO_DIM_ARRAY
    SDO_DIM_ELEMENT('X', 400000, 700000, 0.05),
    SDO_DIM_ELEMENT('Y', 300000, 600000, 0.05)
    INSERT INTO user_sdo_geom_metadata (table_name, column_name, srid, diminfo)
    VALUES
    'OBJECT1',
    'GEOM2',
    2180,
    SDO_DIM_ARRAY
    SDO_DIM_ELEMENT('X', 400000, 700000, 0.05),
    SDO_DIM_ELEMENT('Y', 300000, 600000, 0.05)
    INSERT INTO object1 VALUES(1, SDO_GEOMETRY(2001, 2180, SDO_POINT_TYPE(500000, 400000, NULL), NULL, NULL), SDO_GEOMETRY(2001, 2180, SDO_POINT_TYPE(550000, 450000, NULL), NULL, NULL));
    CREATE INDEX object1_geom1_sidx ON object1(geom1) INDEXTYPE IS MDSYS.SPATIAL_INDEX;
    CREATE INDEX object1_geom2_sidx ON object1(geom2) INDEXTYPE IS MDSYS.SPATIAL_INDEX;
    SELECT *
    FROM object1
    WHERE
    SDO_RELATE("GEOM1", SDO_GEOMETRY(2001, 2180, SDO_POINT_TYPE(500000, 400000, NULL), NULL, NULL), 'MASK=ANYINTERACT') = 'TRUE';
    SELECT *
    FROM object1
    WHERE
    SDO_RELATE("GEOM1", SDO_GEOMETRY(2001, 2180, SDO_POINT_TYPE(500000, 400000, NULL), NULL, NULL), 'MASK=ANYINTERACT') = 'TRUE' OR
    SDO_RELATE("GEOM2", SDO_GEOMETRY(2001, 2180, SDO_POINT_TYPE(500000, 400000, NULL), NULL, NULL), 'MASK=ANYINTERACT') = 'TRUE';
    DELETE FROM user_sdo_geom_metadata WHERE table_name = 'OBJECT1';
    DROP INDEX object1_geom1_sidx;
    DROP INDEX object1_geom2_sidx;
    DROP TABLE object1;
    Thanks for help.

    This error appears in GeoServer and SQLPLUS.
    I have set up a completly new database installation to test this error and everything works fine. I tried it again on the previous database but I still get the same error. I also tried to restart the database, but with no luck, the error is still there. I geuss something is wrong with the database installation.
    Anyone knows what could cause an error like this "End of TNS data channel"?

  • Spatial index creation for table with more than one geometry columns?

    I have table with more than one geometry columns.
    I'v added in user_sdo_geom_metadata table record for every column in the table.
    When I try to create spatial indexes over geometry columns in the table - i get error message:
    ERROR at line 1:
    ORA-29855: error occurred in the execution of ODCIINDEXCREATE routine
    ORA-13203: failed to read USER_SDO_GEOM_METADATA table
    ORA-13203: failed to read USER_SDO_GEOM_METADATA table
    ORA-06512: at "MDSYS.SDO_INDEX_METHOD", line 8
    ORA-06512: at line 1
    What is the the solution?

    I'v got errors in my user_sdo_geom_metadata.
    The problem does not exists!

  • Slider with more than one thumb

    Hi,
    does anybody know a slider with more than one thumb?
    The JSlider-class only provides one thumb, but I need more thumbs to displace.
    That why I posted the last question: I found one in the web but when I call the constructor, I get that error.
    Thank you all
    Katharina

    Hi,
    I also tried MThumbSlider, a.k.a. CMThumbSlider (C for
    Cougaar?), the slider with more knobs. (keywords: slider,
    knob, knobs, thumb, thumbs, more, two, three.)
    I downloaded the code from the link mentioned below,
    run the example and it worked just fine. When I tried
    to subclass the slider to add tooltips I got an exception
    from the loader:
    UIDefaults.getUI() failed: no ComponentUI class for:...
    The slider has its own package. Its constructor
    (indirectly) calls the following utility function,
    passing itself as an argument, just before calling
    JSlider.updateUI. The latter then calls UIManager.getUI,
    which fails with the exception mentioned above.
      public static void setUIName(JComponent c) {
        String key = c.getUIClassID();
        String uiClassName = (String)UIManager.get(key);
        if (uiClassName == null) {
          String componentName   = c.getClass().getName();
          int index = componentName.lastIndexOf(".") +1;
          StringBuffer sb = new StringBuffer();
          sb.append( componentName.substring(0, index) );
          String lookAndFeelName = UIManager.getLookAndFeel().getName();
          if (lookAndFeelName.startsWith("CDE/")) {
            lookAndFeelName = lookAndFeelName.substring(4,lookAndFeelName.length());
          sb.append( lookAndFeelName );
          sb.append( key );
          UIManager.put(key, sb.toString());
      }When the slider is subclassed outside of the package,
    the above results, e.g., in
    UIManager.put("MThumbSliderUI", "MetalMThumbSliderUI");thus the package name is lost. To correct such behaviour
    I changed the substring with the package name, including
    the last dot. The same goes for function createUI.
    There is another thread on this subject:
    http://forum.java.sun.com/thread.jsp?forum=57&thread=348245
    The link were I found the code is
    http://www2.gol.com/users/tame/swing/examples/JSliderExamples1.html

  • Is there a stereo bluetooth headset that can pair with more than one device at a time?

    Is there a stereo bluetooth headset that can pair, i.e. multipoint, with more than one device at a time?
    Are the MacBook and iPhone 4 capable of multipoint bluetooth technoloagy?
    The goal is for my wife to be able to watch her Korean TV soap operas on her MacBook and still receive a call on her iPhone 4 via a stereo bluetooth headset.
    I was looking at the Motorola S10-HD but after further review saw that it only pairs with one device at a time.
    Appreciate any and all input. My Googling has returned no results.
    Rick

    TeslasBB wrote:
    pairing my BB8330 with my blue tooth earphone(TM:jawbone) and my microsoft sync thats in my car simultaneously? if i pair with the car, will i have to pair my jawbone all over again?
    You can only pair one device at a time to your 8330, or any other phone for that matter.  The "pairings" are saved to the phone, you can use one or the other and you won't have to pair it again.  Once you turn your bluetooth device on and the phone is on, they will find each other again.
    Hope this helps,
    John
    Stevie Ray! 1954-1990
    ** Don't forget to resolve your post with the accepted solution.

  • Can I use a magic trackpad with more than one Mac at a time?

    I am attempting to pair a MTP with a second MacBook Pro.  So far I can't get system preferences to find the MTP.
    I am wondering whether the MTP can be paired with only one Mac at a time, and that this is why my MBP won't find it.
    The reason I am thinking this is because the little booklet that comes with the MTP says 'after you pair your MTP with a Mac, you can pair it again with a different Mac.  To do this, you first remove the existing pairing and then pair the trackpad again'.
    Can anyone advise, please?
    If it can be paired with more than one MBP at a time, any suggestions why my system preferences search for the MTP is not producing any results?
    Thanks

    Yes, your keyboard, mouse or trackpad can be paired with multiple Macs.  You can even have multiple keyboards, mice or trackpads paired with one Mac.  The caveat is that the device can only be connected to one Mac at a time.  The device can't be paired or connected with a Mac while it's currently connected to another.
    Pairing a device with 2 Macs will be troublesome if the Macs are located within 33 ft of each other.  The device will connect with the first available paired Mac and then unavailable to the second.   If the Macs are located outside the 10meter range, it's quite easy to power off the keyboard (forcing a disconnect) then walking the keyboard to Mac 2 and powering the keyboard on.   I do this with a keyboard from my iMac to a Mac Mini in another room.
    Captfred

  • Send email from SAP with more than one attachment

    Hi all,
    How can i send email with more than one attachment and different types of document(doc,pdf,etc.) from SAP to external?
    Besr regards,
    Munur

    Hi,
    I use :
    CALL FUNCTION 'SO_NEW_DOCUMENT_ATT_SEND_API1'
    the main problem with different attachemts is to genereate the packing_list.
    the packing list is a kind of description of the data table... where ist the start  of an image, end, size...
    "Creation of the entry for the compressed attachment
            objpack-transf_bin = 'X'.                    " it could be an image
            objpack-head_num = lv_head_num_count .  " inital 1 each att  add 1
            objpack-head_start = 1.                     " fix
            objpack-body_start = gv_startnum.    " table with attachments  1. line one
            objpack-body_num = tab_lines.          " how many lines are in the table of attachment
            objpack-doc_size = tab_lines * 255.   " size of the  attachment...
           objpack-doc_type = lv_typ . " 'JPG'.
            objpack-obj_name = 'ATTACHMENT'.
            objpack-obj_descr = lv_stripped_name  " name of the JPG
       APPEND objpack.
       APPEND LINES OF lt_goscontent TO gt_maildata.  " data Table...
    bestreg
    robert

  • By subscribing to Creative Cloud(Photoshop and Lightroom), does it come with more than one license, and is it possible to install it on both Windows and Apple(if it comes with two licenses)? Thank you.

    By subscribing to Creative Cloud(Photoshop and Lightroom), does it come with more than one license, and if it does, is it possible to install on both Windows and Apple's OX? Thanks.

    A Cloud subscription provides for installing working installations on two machines.  You can have mixed operating systems (both Windows and Apple's OX).

  • When I import a cd with more than one artist iTunes separates each individual artist - how do I get it to show the album as a whole rather than individual artist?

    When I import a cd with more than one artist itunes shows each artist's song separately and won't group the album as a whole - this is incredibly frustrating something that Windows media player doesn't do. Does anyone have a simple cure for this annoyance?

    Generally all you need to do is fill in an appropriate Album Artist. For more details see my article on Grouping Tracks Into Albums, in particular the topic One album, too many covers.
    tt2

  • Can you sign in with more than one apple id on an iPad?

    Can you sign in with more than one apple id on an iPad?

    Only one account can be signed in at a time (via Settings > Store), and if you turn on automatic downloads and/or download past purchases from an account then you risk tying the iPad to that account for 90 days : http://support.apple.com/kb/HT4627

  • Why is all my icloud account linked with more than one apple id?

    why is my iphone 5 merged with more than one account?

    What do you mean by "merged with more than one account" and "linked with more than one Apple ID"?  What exactly are you seeing on your phone?

  • HT1040 Is there a way to place an order with more than one item at a time? For example I am going to make a few books and have them all shipped to me.  Do I have to order and pay shipping for each one individually?

    Is there a way to place an order with more than one item at a time?  for example I am making a few books and having them all shipped to me.  Do I have to order each one separately and pay shipping each time?

    You have to order each book separately, if the books are different. Only multiple copies of the same book can be ordered in the same order, see here
    Regards
    Léonie

  • How can i use Itunes to update more than one IPad with more than one owner

    How can i use Itunes to update more than one IPad with more than one owner?  I own an IPad and my wife owns an IPad.  I want to use my system to update both IPads.  We have different Apple Accounts and different applications.  Is this possible?

    Of course, that is too easy.  I am such a bonehead.

Maybe you are looking for