[K8N NEO FSR] Running DDR 200?

I am currently using the 1.3 bios, and I see the 1.1 bios fixed this problem (or one very similar to it).
I have tried all three dimm slots and they will all run my ddr400 sticks at 200. Is this just a display bug? Should I get a new bios? Is it the ram?
AMD 64 3200+
MSI K8N NEO FSR (1.3 bios)
2 x 512mb pc3200 corsair value ram
eVGA Geforce 6800GT

Dual Data Rate.....200 x 2 = 400!!!
That is shown correct!
You are running at DDR400 speeds!!!

Similar Messages

K8N Neo FSR Bios overclocking functions help needed

Hi all, I am a small pc builder for the family and i have found some problems with the bios of my uncles K8N neo FSR which I recommended for him. Basically it wouldn't seem to overclock with the 'Dynamic Overclocking' function on bios v1.7 but did manually by adjusting FSB incrementally (ie from 200 to 205 Mhz). When I questioned this before someone had mentioned that it could be ok to run like this. However I have since updated the bios to v1.9 and even v2.1 as they became available but now neither seem to overclock manually nor using 'Dynamic overclocking'
Firstly though, can someone clear up my first conception; To test if the Dynamic Overclocking function is working can I set it to a higher setting (ie.'Commander'), save and exit bios (restarting) ---> go straight back into bios ----> go straight back into Cell Menu and check 'Current frequency of cpu' has changed?
I only ask this as if this is the case then my Dynamic Overclocking function hasn't worked with three bios' and I wont bother with anything until I RMA the board lol, as I have never been able to change the frequency of my cpu at boot/bios stage with the dynamic overclocking function.
Can anyone help me?

Hi Stu, yesterday I think i found out what u mean lol. I studied a 'Sticky' ? about overclocking A64s and found some interesting stuff. Apparently overclocking the HTT is dangerous, and A64s are always at least half locked. Now with this in mind Ive been wondering if there are interlocks built into my mainboard stopping me from using the 'CPU Overclock' function to overclock my pc manually from the set 200Mhz while my HTT is still set at 4x. -I say this as the HTT on my system is 800Mhz for a socket754 Sempron 3000Bx, thus overclocking this would increase my HTT above the 800Mhz threashold (I think) lol. All sounds complex but I think Ive figured it out as Im following instructions from the sticky to lower my HTT multiplier before increasing my cpu overclock. Its hard as my mainboard has Nforce3 chipset which has different ways of overclocking to every other board lol. So far I have managed to increase the overclock, but only when the HTT multiplier is lowered to 3x. I have also lowered my cpu multiplier though, and thus am trying to figure out where my 1810Mhz clock speed has changed to 1630 lol. Will try again now. I want to raise the clock speed above 1810, keeping the HTT lower than 800 and leaving the memory alone at 400DDR lol. Im hoping the memory is seperate as it seems to be on this chipset.

Have you sucessfully overclocked you K8N Neo FSR? Plz post details.

Hi guys !
Im still stuck with my system that does NOT want to be overclocked so I wanted to know if I'm the only one or not ?
If you have managed to overclocked you system using K8N Neo FSR please post you details.
And I'm also looking for tips on how to bypass issues related to unsucessful overclocking.
Thank You.
I've managed to do this so far...
A64 3200+ NewCastle CG-stepping @ 210x11 vCore 1.55
Corsair Value Select DDR 400 @ 3-3-3-8-2T VDimm 2.70
using official BIOS version 1.4
But that's it...
If I increase vDimm above 2.75 = NoBoot/Unsucessful Windows Login
If I increase FSB above 210 = NoBoot/Unsucessful Windows Login
If I set FSB 230x10 = NoBoot/Unsucessful Windows Login
If I set timings to higher values e.g. 3-5-5-10 = NoBoot/Unsucessful Windows Login

Gen,
I found a few interesting things last night. 1st, I was having a problem with my CPU and Northbridge fans throttling down to about 1/3 speed after a few minutes of use. I disabled the Northbridge and CPU target fan settings in BIOS. You can find these options in the System Health menu of your BIOS. Also, if you have enabled the "Optimized" option in your BIOS, please disable it and set to "manual". The only option I've found to help is to select "Aggessive" timings for your memory. It doesn't change your speed in the BIOS for some reason, but it does do something else because my memory bandwidth is about 60 more with this setting enabled instead of disabled (3430 Int / 3430 Float in Sandra 04 versus 3493 / 3496 with the setting enabled. OF ALL THINGS MAKE SURE TO DISABLE THE "OPTIMIZED" function and leave it set at manual. Also, shoot me your current memory timings one more time. Are you using BIOS rev. 1.4? Let me know. Sorry it takes so long between posts, but I check from both work and home and it's usually several hours between getting chances to check for updated posts. I didn't have to reduce the HT setting on my overclock (I'm still running 4X), but I've read several posts where a setting of 3X will help if you're having problems o/cing. Also, on your memory timings make sure and set your DRAM to FSB ratio at Auto. This allows the memory to sync with your FSB speed. And, I don't remember if I mentioned it before, but be sure to set your AGP speed to 67 (66 is the default). At a setting at 67 it will positively lock your PCI and AGP clocks to 67 and 33 respectively, making sure that you aren't overstressing any of your PCI devices or you video card.

S3 mode doesn't work fine on K8N Neo-fsr since overclocking, please help!

I have a K8N Neo-FSR (MS-7030) BIOS version 1.6 (I tried 1.4, 1.5), running AMD64 2800+ SK 754, 2x 256MB DDR400 Kingston valueram pluging in slot 1&2. It runs well except S3 mode .
Since I overclock HTT (everythings else have their own default values), S3 mode seems to work so crazy . After wake up from this usefull stop-grant standby mode, HTT is given back to its original speed, 200MHz, without notice (?!) .
You know that I don;t like this much, do you?
Who responsible for this function? Mainboard or CPU? If it's mainboard, which department will be sentenced, BIOS or chipsets/ICs?
Could anybody give me a solution to achive higher speed by overclocking without giving up using S3?
Thanks so much!

It's a bad new! I had bad feeling about DFI with the same problem, S3 mode resuming bring FSB back to df and even sometimes led the system to the ruin. But upgrading bios solved this issue. My old Abit did S3 mode fine. Now I have a new MSI and once again I must use teknophyle's way or slow hibernation instead.
On the same occasion, I wana ask about some shortcoming in 1.6 bios: power on by keyboard/mouse and power led options. I only found S3 wake up by keyboard/mouse but not keyboard/mouse power-on options! There is power led option in version 1.56 but it disapeared in 1.6. Now my mobo has no signal to differentiate between sleep and power-off. would you give back the useful power led option and add power on by combination keys in the near future bios version, syar? Look forward to hearing some good new from you :D.

K8N Neo-FSR doesn't boot

Hello everyone
I got my mobo (K8N Neo-FSR) more than 6 months ago, and worked without any problems until today.
First of all, I made a BIOS update from 1.7 to 1.9 using MSI Live Update. No problems to report, the computer worked after that for several hours. Then I turned off the PC. And the next time I wanted to turn it on, it didn't boot.
Here's my D-Bracket message :
This corresponds to "Initializing keyboard controller"
The problem is that apparently it has absolutely nothing to do with my keyboard, as I tired changing it.
Clearing CMOS didn't help.
Any ideas how I can fix this? Or should I contact the support?

Before you answered, I tried to check the RAM. As a matter of fact by removing one of 3 memory sticks the computer worked. Later I figured out that if I lower the RAM frequency from 200 MHz to 166, all 3 sticks work perfectly well.
Now the question is : WHY THE HELL DID THIS BIOS UPDATE MESS UP MY RAM??? Weird.

K8N Neo-FSR v2.0 + Sempron 2800+ E6 = No Go?

Hello!
Wanted to assemble a rig for playing around with Ubuntu 64-Bit, so I headed out and obtained ...
... a MSI K8N Neo-FSR v2.0 (7030-20C, shipped with BIOS 5.10)
... a AMD Sempron 2800+ (Palomino, Step E6)
Upon power-on it refuses to POST ---> 1 continous beep
If I recall the AWARD beep-codes correctly this means that the CPU failed to initialize.
Troubleshooting steps:
- Stripped down to board + CPU + 1x RAM + GFX -> No Go (1 beep)
- Stripped down to board + CPU + 1x RAM -> No Go (1 beep)
- Stripped down to board + CPU -> No Go (1 beep)
Meanwhile I tested the CPU and RAM in in another S754 board a friend borrowed me ... both work fine.
So this leads me to the question:
Does anyone has a clue what might be wrong here? I don't have greater experiences with nForce boards so my knowledge about them is very limited.
Thanks for helpful suggestions.
-Storm

Quote from: syar2003 on 27-August-06, 20:29:14
This is the latest bios version of the 5X bios series (and should be a safe one since yours is currently running with 510).
http://download.msi.com.tw/support/bos_exe/mbd_bios/7030v54.zip
Don't know if it will add support for your cpu though.
Well ... as the changelog of the BIOS isn't exactly informative we would only know if I could get the board to POST so that I would be able to flash.
This however isn't a valid option as the board keeps on beeping upon power-on.
Quote from: syar2003 on 27-August-06, 20:29:14
Theese 7030 boards have become unbelievable hard to track as there are so many versions released now.
ref: http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_detail.php?UID=688
This page also lists another bios series to use 1X and 9X series
In addition it lists 2800 E6 Palermo as NONE (which means not verified/under testing)
Direct link to many 7030 boards bioses are also gone .
You're right --- I did some more investigation yesterday and became award of the "too many 7030's" issue. The one I'm referring to is actually the one you linked at (K8N Neo-FSR V2.0).
As the sticker on the flash reads v5.1 I assume the board is PCB rev. 1 ... as the 9.x BIOS seems to be for PCB v3.0 only.
Took a look through the CPU Support ... and ... WTH?
Only Turion CPUs and one A64 (step E6) is listed as compatible?
Guess we found the showstopper ... either the board or BIOS seems to dislike the E6 Sempron then. Hmm ... guess I either return the CPU or the board. It seems as getting a Turion would be the better choice as the shops in my area don't have anymore AGP S754 boards (and the same goes S939 boards). I only need a rig to play with server setup-scenarios of Ubuntu 64-Bit and no powerhorse for gaming or such.
Thanks for pointing me to the CPU support list ... I would have never dared to imagine that a board will only run with a limited set of AMD CPUs ...

K8N Neo-FSR - SATA?

hello, in case I missed the information I apologize . I got the K8N Neo-FSR and I want to ask if there is four Sata support on the board. I have noticed that on the board and also on your homepage-pictures there is only support for two Sata (Sata 3, Sata 4), but in the manual there is support for up to four Sata.
Is it four or two Sata support on the board?
Thank´s

Quote
Can I run single sata drive on them without pata drive
- Yep just plug it into either socket.
Quote
use the rest of sata drive (140gb) normally?
- No. if using raid it's preferable to use drives of same model (so that they share operating spec) & size so that no wasted space.
You may find this sticky link useful Raid Guide
luck

K8N NEO FSR - wont detect HDs on first powerup (daily)

I'm having this strange problem ever since i installed this Motherboard.
First time I boot up(daily basis), it does not detect the hard drives.. any of them...
I get to the point where it notices my memory timings and says "Detecting hard drives.." (or something like that) and it just hangs there. I hit ctrl-alt-delete (also if i power it off then back on it works too) and when it comes back its fine.
Anyone had this before? Could be there's a quick fix but before I start to pick the system apart I wanted to check here first.
thanks

OK here are some specs:
AMD64 3200+ (Newcastle) - no OC
Generic 3200 DDR ram
MSI K8N NEO FSR (latest bios)
BFG 6800 OC (modded)
primary controller (ata) has: Maxtor 6Y060P0 & WDC WD800JB-00DUA3
secondary controller only has DVD-RW drive.
Sata controller has ST3120026AS
Same setup as in previous motherboard.
I guess i'll just need to check the cabling is secure once again, to be sure.
it seems this is not a common issue so most likely i can find something wrong other than with the mobo.
thanks

K8N Neo FSR doesn't post

Hello all,
I have just finished building a new system, based on the Athlon64 and using the K8N Neo FSR mobo. Of course the system doesn't post, it instead gives out an endless series of beeps, about 3 seconds apart, and the D-Bracket gives me the error code in which only LED #3 is green - meaning "Initialing keyboard controller" which means nothing to me, as the keyboard is hooked up, and I checked re-checked and double re-checked the connection.
So I go about the usual diagnosis tactics, disconnecting device after device until I am left with only the CPU and one module of RAM, and still no post. I tried swapping the PSU (both rated 500w, although only 18a on the 12v+ rail). I also tried a memory module from a working system (a P4 one). I tried resetting the CMOS using the jumper.
One weird sidenote, is that the system did post twice (from over a hundred times) but it didn't get past the system information screen.
I have built several systems in my life, and this is the hardest time I ever had.
If anyone could think of something useful (except buy a new mobo), I would be very grateful.
Full system spec (if it helps, I tried it completely barebones and it made no difference):
CPU - Athlon64 3200+, including generic Heatsinc and Fan
Motherboard - MSI K8N Neo FSR, Award Bios
Memory - 2x512 Corsair value 400Mhz DDR
Hard Drive- Western Digital Caviar 200Gb S-ATA 150
Graphics Card - PNY Verto Geforce 6800 GT
PSU - L&C p4 LC-B500E - +3.3v 28A, +5v 50A, +12v 18A, -5v 0.8A, -12v 1A, 5VSB 2.5A
Several other optical drives that are currently disconnected, pending system starting to function.
No O.S has been installed yet, as the system doesn't even post.
Thanks in advance.

Quote
Originally posted by egg1981
Hello all,
I have just finished building a new system, based on the Athlon64 and using the K8N Neo FSR mobo. Of course the system doesn't post, it instead gives out an endless series of beeps, about 3 seconds apart, and the D-Bracket gives me the error code in which only LED #3 is green - meaning "Initialing keyboard controller" which means nothing to me, as the keyboard is hooked up, and I checked re-checked and double re-checked the connection.
So I go about the usual diagnosis tactics, disconnecting device after device until I am left with only the CPU and one module of RAM, and still no post. I tried swapping the PSU (both rated 500w, although only 18a on the 12v+ rail). I also tried a memory module from a working system (a P4 one). I tried resetting the CMOS using the jumper.
One weird sidenote, is that the system did post twice (from over a hundred times) but it didn't get past the system information screen.
I have built several systems in my life, and this is the hardest time I ever had.
If anyone could think of something useful (except buy a new mobo), I would be very grateful.
Full system spec (if it helps, I tried it completely barebones and it made no difference):
CPU - Athlon64 3200+, including generic Heatsinc and Fan
Motherboard - MSI K8N Neo FSR, Award Bios
Memory - 2x512 Corsair value 400Mhz DDR
Hard Drive- Western Digital Caviar 200Gb S-ATA 150
Graphics Card - PNY Verto Geforce 6800 GT
PSU - L&C p4 LC-B500E - +3.3v 28A, +5v 50A, +12v 18A, -5v 0.8A, -12v 1A, 5VSB 2.5A
Several other optical drives that are currently disconnected, pending system starting to function.
No O.S has been installed yet, as the system doesn't even post.
Thanks in advance.
I got the same problem let me know if u fix this....

K8N Neo FSR won't boot.

I've flashed mainboard BIOS using LiveUpdate from v1.6 to latest v1.9 for some reason (CPUID for Sempron 64bit, low DDR speed). Everything ok . Then XP became unstable (blue screens) and finally PC wont boot (one LED is green, nothing appears on the monitor) . Any idea, except to put it back to the reseller, what I probably have to?
Does anyone have the dg. LED description for this board (there's neither anything in my printed manual nor I've found this in the web)? The description was there for older mainboards, why is this not there now???

you did the big mistake if you used live update!!!
Bios flashing and live update:
look at this: https://forum-en.msi.com/index.php?topic=84865.msg606175#msg606175
and this: https://forum-en.msi.com/index.php?topic=14909.0
and this https://forum-en.msi.com/index.php?topic=69.0
something abou Bios recovery:
https://forum-en.msi.com/index.php?topic=71165.0
https://forum-en.msi.com/index.php?topic=65951.0
btw look at this, it`s about bios version 1.9 for MS-7030, this bios has lots of bugs at K8N Neo-FSR:
look at this: https://forum-en.msi.com/index.php?topic=87562.0
and this: https://forum-en.msi.com/index.php?topic=86772.0
I suggest you to revert back to official version 1.7 (which is stable) or modded version 1.56 by pinochio...look at this: https://forum-en.msi.com/index.php?topic=59711.0 and also look at syar`s collection: http://homepages.nildram.co.uk/~chsmith/Syars_Bios_Collection/
go to NEO1 and download 7030MOD.156

[ram]Kingston + MSI K8N Neo-FSR?

my system:
AMD Athlon 64 3000+, 2.0ghz
MSI K8N Neo-FSR(bios 1.40)
Asus V9999 GeForce 6800 256MB Gamer Ed. AGP
Audigy 2 zs
Win xp pro sp1
Hiper power 420W
I just bought the Kingston ValueR. PC3200 DDR-DIMM 1024MB Kit w/two matched ValueRAM 512MB.
When I boot up the pc just makes a sound piip piip piiip continuing....
I can't do anything since it wont boot up & i tried diffrent dimm slots but it didn't work :(
Earlier i've set the settings to t1 & the volt to 2.56 from before. Does this has something to do with it ? How can I reset the bios if I can't even get in dos :s
What should I do ?

Reset the cmos using the Jumper, is you have a manual it will show you where this is located. It will set the Bios back to Default,then you have to set it up the way you want it again. To get the RAM working set it to DDR333=166, that should sort out the No Post.
Your going to be out of luck here as the 'support' is basicaly non-existent, or just replies from people trying to get their post count up higher, I'm afraid to say.
Good luck.

Aaaaaaahhhhhhhhhhhhhhhhhhhhhhhhhh!!!!!!!!!!!!!!!!! Usb And K8n Neo-fsr??? What Solution???

AHHHHH! What it is occurring?
Reason that the MSI does not decide this problem of the peripherals
(mouse, keyboard and others) that they are not recognized when the operational
system comes to tona?
What incautiousness is this?
I am thinking seriously about changing my K8N NEO-FSR for an
equivalent of the Gigabyte.
In the majority of fórums in the world that speaks on series K8N and
K8N2 they come reporting this problem.
I ask for to more care with its fidiciary offices customers, therefore we deposit our investments in its equipment MSI.
I am tired to have that to replugar mine mouse, when exactly reinio the computer. Without speaking in my card of memory.
The problem if reproduces in all outputs USB.
Already I reinstalled the operational system and everything continues
in the same one.
These same peripherals functioned very well in a K7N2-L with nFORCE 2.
Ahhhh! I changed the cursed one and exactly thus it continues.
Necessary of a solution of the MSI already.

OK I am also running Win2k. I beleive you must have the latest service pack 4 to get proper usage of USB 2.0.
Also in device manager under USB 2.0 Root Hub in the Properties/Power Management tab do you have The allow Computer to turn off this device to save power turned off? You may also check and see if any USB device in Device Manager has that turned on. If it is checkmarked then uncheckmark it.
Outside of that you could have a device that is attached that is causing the issue. Try one device at a time and see if you still get the problem. I have been through this myself but luckily not on my current board. I had that problem when I had a USB card in my old ASthlon 1200 system on an A-bit board. However what I just listed fixed it when I discovered a device (A mouse if I remember correctly) was not functioning well.

K8N NEO-FSR No Post

I just bought a new K8N NEO-FSR to replace another MSI motherboard that I have been having trouble with and need to RMA. I have it on the bench, with a AMD Sempron 3300+ processor, 1 stick of Kingston memory 512mb 266mhz DDR, Nvidia Geforce 2 mx/mx 400 graphics card and Silencer 410 ATX PS.
>I just modified the LED lights below to make correct<
My problem is it will power up and stay powered up but won't post. I have no beeps. The LED will flash:
1st--number 3 green,
2nd--3 stays green with number 4
3rd--3 stays green with number 2
4th--Starts all over with same above
Then it just repeats, repeats, repeats the above unless I turn it off???
I have reseated everything several times. What's going on? Since 4 and 2 are last to green up before repeat, does that mean the Bios is bad on this board?

Quote from: kakarocht on 27-July-06, 12:32:58
Have you tried to changed other PSU? Seems like you've a weak PSU. IF you can borrowed a PSU from your friends or purchase it like OCZ, enermax or tagan.
PSU shouldn't be a problem here, since it's not a power hungry system.
check the post from built2last and identify at which stage the d-bracket stops. than you will have to check that code in the manual and tell us what it is.

Ms-7030 msi k8n neo fsr wont start

i made my system a follows.
amd 2800+ 64
msi k8n neo fsr
kingston 400mhz ddr value ram
6600gt inno3d agp
wd800 80gb hardrive
300 watts psu
brought the system home everything was working fine except for continous stuttering on hl2. also wid it came a smart cobra lite 56k modem from zoltrix, which was installed while makign the system, the modem had been deteced but when i tried to connect to the net, the status of the modem was found to be not connected, i removed the modem, restarted by switching the pci slots and everything but to no avail, put in an older zoltrix modem from my old pc, to no avail the modem just wudnt get recognized. the same modem though worked in my older p3 system. i took the systm to the place where they assembled it.as the system booted the modem got deteced, got winxpsp2 installed wid a fresh install. everything worked fine for a day untilt eh modem once again went back into death mode.took it back to the hardware shop i remember they were using an older keyboard on it too, well as they pressd the power button, the cpu fan and the gfx card fan moved a second and then stopped no booting
they replaced mobo then and there. even the same problem occured wid the new mobo, i left the system there to be tested but the thing i dont understand is they had assembled an tested the system by using the old keyboard and even then there was no problem. this time the system was working but as it reached the assemblers the cpu and gfxs card fan moved a sec as if power was fed for a second and dided changed psu's on one try on dry boot that is widout hd connected. the fans continously worked we removed power put into chasis and tried again to start but to no avail.
cud it really be the keyboard problem if that is solved then the problem left to deal wid is the modem wud the pci slots act the same way even on the newer board or chaning modems wud do any good, changed rams also that wudnt help booting either.
in both of the new mobos i didnt get the msi sticker that adds to my frustration.
posted this on another forum too, tha guy was havng problem using an older keyboard.

its really nice of u guys to reply so quickly its really appreciated. the thing is if the psu wasnt upto the job it wud have given away 3 days ago. but it didnt other psu tried also same problem. after a couple of hours ill be off to the hardware shop to see wat came out. the ram was reseated properly on all 3 slots.
plus the 300watts psu may not even be 300 cuz its locally made and stupid quality maybe lower to around 250, but the system worked fine all along, checked rail supplies on the mobo mopnitor and they seemed fine.will keep u guys updated.

K8N Neo FSR, possible BIOS bug: setting Vcore with Cool'n Quiet enabled broken?

Athlon 64 3400+, socket 754
K8N Neo FSR, Pheonix-Award BIOS V1,5
WinXP SP2
Having Cool'n Quiet disabled in BIOS setup, CPU core voltage adjustment
using 'Adjust CPU VID' below the Athlon 64 default 1,5V core voltage
works like a charm. Fine!
But with Cool'n Quiet enabled in BIOS setup (and WinXP), under load the
CPU core voltage raises to 1,5V in any case, independently of what I did
define in BIOS setup with 'Adjust CPU VID' (e.g. 1,4V). Software tools setting
Vcore like Core Center are not running.
So I can choose to either run a silent system in idle mode with Cool'n Quiet
enabled or under heavy CPU load with Cool'n Quiet disabled but Vcore
reduced :-( Am I missing something or does it rather look like a BIOS
bug?
Greetings, Falo

Quote from: Tiresmoke on 21-March-05, 00:19:19
As undervolting is not considured standard operating proceedures then how can it be considured a bug.
nor is overclocking but MSI mobo manual reads 'This motherboard is designed to support overclocking.'
So this mobo is designed for supporting at least one non standard operating procedure
Seriously, if BIOS offers a feature I suppose it to work as expected.
regards, Falo

[K8N NEO FSR] Running DDR 200?

Similar Messages

Maybe you are looking for