K8N Neo PL and USB flash memory

This is a bit odd, not really sure what is happening. I have tried a couple of different flash memory readers, as well as flash memory sticks, and the USB does not recognize them. I can plug in scanners, mice, etc. and they all work perfectly. It is just when I use some type of memory device that is plugged in by the USB port do I have problems.
Is anyone else having this problem? I have enabled/disabled the USB using rev. 1.1 and 2.0, enabled and disabled the USB Keyboard/Storage setting, and I have re-installed the WinXP drivers that handle this (as well as try to update those very same drivers).
Here are my specs:
AMD A64 3400+
1 GB Mushkin PC3200 Level 2
120 GB SATA Seagate Drive
Toshiba DVD-ROM
Sapphire X800 Pro
CL Audigy 2 ZS
WinXP Pro SP1
NVIDIA 4.24 Unified
DX 9.0b

I fixed my own problem. On searching a few other forums I read that the problem actually comes from the front panel USB connectors. Most of these connectors have 2 ground wires coming off of USB 1, and to get everything to work properly only one of the grounds should be plugged in. The farthest ground (in my case the wire was brown) should be unplugged, so that only 4 wires are plugged into the USB pins.

Similar Messages

Unable to boot from my USB Flash Memory Device

Hi there,
I recently purchased a macbook pro with the lion 10.7.2 firmware.
I am experiencing problems with my USB Flash memory as when i plug it in it comes up fine on the desktop and i can browse it. The problem is that when i open up an application such as Adobe Fireworks or Netbeans (Java programming) and try and access files from my USB flash drive, my drive does not appear on the list/menu, it only comes up with my macbook pro documents etc.
I have asked friends with Mac's and they tell me they do not experience this problem. Please can you help me whether it is a problem with my settings or any other issues.
Thank you.

Nope, I dont recieve any massages at all. It just doesnt appear.
Also usually you can drag a file into an application, for example drag an image into photoshop in order to open that image up but this does not work either.

I've bought a new USB flash memory. I plugged it in the USB port then a message come out: Because a USB device was drawing too much power from your computer, one or more of your USB devices have been disabled.... Please help...

I don't know what to do. I plugged that USB in both ports but the same message came out. I charged my laptop and the same thing happened again. The surprising thing is that I tried plugging the USB in my cousins laptop (Macbook Pro) and it worked!!! but not with mine. The USB flash memory made by PNY. Please help...

There are two types of USB 2 devices - low power which consume 100 milliamperes or less from the USB bus and high power which consume up to 500 milliamperes. Your flash drive is probably a high power device and is overloading the USB bus of your computer. (Some notebooks can support only low power USB devices.)
I know that my MBP's USB ports support high power devices but I've come across reports that not all high power devices will work on the MBA and that might be the case for your flash drive. My guess is it has a large capacity? 32GB or more?

USB flash memory: "application not found" error

When recently trying to use a USB flash memory stick I was getting an "f:\ application not found" error. I tried all kinds of fixes from Microsoft. Turns out it was caused by Lightroom.
Since the memory stick had photos on it, my computer's Autoplay was trying to launch Lightroom. Problem is, Lightroom is listed as "Lightroom 4.0 64" in the Autoplay menu. I have Lightroom 4.4. As far as I can tell, there's no way I can fix the incorrect "Lightroom 4.0 64" listing. The solution is to remove Lightroom from any Autoplay options.
This is the second such problem I've had with Lightroom. The previous problem was right clicking on a photo file and trying to use the "open with" menu. It worked fine when I had Lightroom 4.3. After updating to Lightroom 4.4, it didn't work. Another Lightroom user found a workaround, which was to rename the Lightroom 4.4 folder back to Lightroom 4.3.
These are both lazy Adobe oversights. You have to realize all the Windows functions that will be affected with an update and make sure they are updated as well. I spent half a day solving this latest USB flash memory error. Get your updating act together.

You don't mention your OS or which version of Outlook you're using.
For Windows, this may be helpful:
http://www.winhelponline.com/articles/236/1/Unable-to-open-PDF-attachments-from-Windows-Ma il.html
Noel

Mounting NTFS,FAT32 and USB FLASH drive

Problem and problem!!
I am going to fade up with Solaris 10. Please somebody help me!!
Problem is with mounting my FAT32, NTFS partitions and USB flash drive (twinmos).
How can I mount FAT32, NTFS file system and my USB flash drive in Solaris 10??

cN: the N'th disk controller installed in the system
tN: the SCSI TARGET id. Also used for atapi, firewire and usb mass
storage device, but it's always 0. Use to identify a specific disk
device on the disk controller.
dN: the SCSI LUN id. For atapi devices this is 0 for master device,
1 for the slave device. For usb mass storge devices this field could
contain a value > 0 - for example usb flash card readers often
present the slots for the various flash card formats as multiple LUNs. For simple usb flash memory sticks, this should be
LUN 0.
sN: the slice N from the SunOS disk label. On a media without a
disk label, slice 2 can be used to access all of the medias contents. Solaris SPARC supports slices s0 - s7, Solaris x86
slices s0 - s15.
pN: on Solaris x86 only: p0 is the whole disk (similar to slice s2,
when there's no SunOS disk label), p1 - p4 are the four primary
fdisk partitions.
The ":c" suffix assumes the media contains the fat filesystem in
a separate fdisk partition, searches the fdisk partition table for
the first partition containing a fat filesystem, and mounts the
filesystem from that partition. On Solaris x86, instead of using
"p0:c" you could also use one of the p1 - p4 device; but the pN
fdisk slices don't exist on Solaris SPARC.

Toshiba 40SL733g - How to play video files from USB flash memory

When I plug my USB flash memory in USB port, Media Player menu shows up with two options : Photos and Settings.
How do I make my TV recognize and play video files from USB flash memory?
Flash is on FAT32.
I have tried to play avi, mp4 and mkv files but nothing happens. It looks like flash is empty.
Could you please help me solve this problem.
Thanks!

bzunic, have you updated the firmware for your model?.
With my own set, (32RL900A), the instruction manual said that certain buttons on the remote control were "unused", however, after the first firmware update, the previously "unused" buttons were used, (In our case, Time Shift, Record, and so on).
The reason I talk about this is, these features became available after a firmware upgrade, and were not mentioned in the user manual, in our case, and a later download of the instruction manual for our model actually gave the instructions for the use of these features, which were shown as "not available", in the original instruction manual supplied with the TV, but became available after the firmware upgrade.
Let us know how it all works out ............
donhe7

Install arch voodoo from usb flash memory

I am interested in anybody crazy enough to try this tutorial I made http://wiki.archlinux.org/index.php/Ins … ash_memory , I tested it with my hardaware and until now it was worked out great, but i am looking for second opinions.
I also posted an updater script that will update the install packages, so you can always carry a freshly updated arch install, anybody willing to test it on any spare usb flash memory or external hd they might have, please do so.
Cheers!
Last edited by thewonka (2007-02-18 07:16:52)

tried out your wiki guide works ok here ... on a 256mb pendrive will say sed command caught me out [could you say in guide what you changed! in menu.lst]
Ok checked pendrive on Laptop boots fine :-) [0.8!!!]
thanks for sharing ;-)
Last edited by Mr Green (2007-02-18 09:33:21)

Create bootable usb flash memory

Hi,
ı have s10-3 ideapad, there is no dvd drive, how can ı create bootable usb flash memory?

Hi and welcome,
...you need a second computer to prepare .
a huge amount of sites describe that "how to prepare usb-drive" ...i picked from net examples for all systems ...
install windows from winsetupfromusb for XP
for Windows 7 USB drive Windows 7
for Ubuntu Unetbootin
and last but not least here in our knowledgebase for XP
regards KalvinKlein
Thinkies 2x X200s/X301 8GB 256GB SSD @ Win 7 64
Ideas Centre A520 ,Yoga 2 256GB SSD,Yoga 2 tablet @ Win 8.1

USB Flash Memory doesn't work !

Hi There.
my USB Flash Memory doesn't work and doesn't appear in disk utility. I also make sure that external disks are checked on Finder Preferences. and it's formatting to be worked with mac. it's work with my friend macbook pro. But Mine doesn't!!!
any help guys i'll be thankful
regards.

Which MacBook Pro do you have and which does your friend have? Do either or both of you have USB 3.0 ports?

Making the HIDDEN File(.DS&Trashes) visible in USB FLASH Memory

Mac always has this .DS and TRASHES folder everytime I use my USB Flash memory, and it consumes spaces A LOT. The problem is I cant see it on my PB, so what I discovered was to connect it to a windows computer to erase those hidden files.
Is there a way I can erase/see these files on my Mac? Finding a windows computer is not always easy here, and quite inconvenient. Thanks!

Try this, it works well for me...especially when transferring files between Mac and PC when all those Finder files show up and get very confusing.
http://www.apple.com/downloads/macosx/systemdiskutilities/findercleaner.html

Booting from USB Flash Memory Card Reader on RS480M2-IL (Test Results)

I just completed testing my USB Flash Memory Card Reader (see profile) as a boot device and wanted to provide feedback to the Forum.
A UBS Flash card will show-up on the Advanced Bios Features menu, Hard Disk Boot Priority list, when a Flash card is physically present in a card slot. It showed as "USB-HDD0 : AFT PRO -8MX CF 0" with a 256MB Compact Flash (CF) card for my test. Using the enter key on the Hard Disk Boot Priority list allows for ordering priority, which was necessary to place the CF Drive before my real Hard Drive for the card to boot. When the card is removed, it drops from the list.
I initialized my CF card as a DOS system disk using HP's USB Disk Storage Format Tool v2.0.6 for the test.
Since it is recognized as a Hard Drive, it boots as the C: drive, not A/B Floppy alternative.
I also ran a quick test to see if XP Pro Setup would see the drive. It does show as my D: drive partitioned FAT. Too small (256MB) obviously for XP Pro install, but it does present opportunity for larger size flash modules. My Flash Reader actually has 4 different disk functions/slot groups, so XP Setup acknowledge the presents of those empty three slot groups as "Unknown Disk" on the drive list.
I hope the information is useful for anyone planning a build or looking for alternative boot methodolgy with the board.
This board just gets better and better.
Danno

So with a nice size flash memory u could start your box with a key drive and lock up your computer when you leave it unattended.

K8N Neo Platinum and Maxtor SATA II 250GB 6V250F0

Hi folks,
Having a bit of fun with this one. After first installing the new hard drive (Maxtor SATA II 250GB 6V250F0) , the BIOS immediately recognised it, I could boot into Windows, and Windows recognised it, and I thought I was in for a smooth ride. Sadly, the good news ends there.
Tried to initialise the disk, but this simply gave an error after a few seconds, and wrote a whole load of controller error messages to the system event log. Since then, I've done the following troubleshooting steps:-
(1) Tried in Normal Mode and Safe Mode, made no difference.
(2) Tried with the jumper on the back of the drive set to limit it to SATA I, as I'm connecting to SATA I controllers on the motherboard. Made no difference with it on or off. Tried a second jumper just in case the first one was faulty; still made no difference.
(3) Tried using different power cables and molex connectors; made no difference.
(4) Tried using different data cables; made no difference.
(5) Tried connecting to each of the four SATA ports; made no difference. Tested each port with another drive ((an older Maxtor SATA I drive, which has always worked fine), and they each worked fine.
(6) Tried with and without another SATA drive (an older Maxtor SATA I drive, which has always worked fine); made no difference.
(7) Checked the drive firmware (VA111630); apparently already the latest.
(8) Used the nVidia registry fix to disable NCQ; made no difference.
(9) Disabled write caching; made no difference.
(10) Ran powermax 4.22 to test the drive, and it reports no problems with the drive at all. Did the full surface scan just in case, and a burn-in test; these also reported no problems. Curiously, they also reported no problems when I did the same tests with the back jumper removed; i.e. running it in SATA II mode when connected to a SATA I port apparently didn't bother powermax. Go figure.
The only way I've got anything to happen with the drive so far is to set it to run in PIO mode(!), which I did briefly, and which enabled the drive to be initialised in Windows. Haven't tried much else in that mode yet, not least because I have no intention of actually using it in that mode for obvious reasons.
So...we have a perfectly functioning disk, attached to a perfectly functioning SATA port, with supposed complete compatibility between them, and with pretty much all other bases covered, and the end result is...it doesn't work.
Has *anyone* got this particular drive model (Maxtor 6V250F0) to work with a K8N Neo Platinum, and if so, how??? ??? ???

Latest Update (this is a real Twilight Zone one ):
LOL, well I should have known better than to be optimistic about anything where this drive is concerned. With Windows drivers installed, it seemed to work okay as a storage drive. So I then installed XP on it, and sure enough it hangs when loading the OS. As the next test, I did a clean install of XP on an IDE drive I have installed, which worked fine (could boot no problems). I then cloned that to the Maxtor drive (the clean OS had no nVidia drivers installed), and not only did the Maxtor drive fail to boot, but so did the IDE drive (even though nothing has changed on that drive!) Both would hang at the Windows loading screen. So then I deleted the partition on the Maxtor drive, so it was effectively back to the situation where the IDE drive booted okay previously (with a blank Maxtor drive attached), but now it continued to fail to load. If I unplugged the Maxtor drive, however, then the IDE drive would boot. If I then re-attached the Maxtor drive, the IDE drive would still boot, even though that would be exactly the same situation in which it didn't boot before the Maxtor unplug and replug. In short, it simply makes no sense whatsoever. ???
A summary of facts/findings:-
(1) System works fine; all components checked and pass diagnostic tests, no Windows problems in the event log or device manager, no random crashes or anything like that. The Maxtor drive passes Powermax tests fine.
(2) If the Maxtor drive is attached while using nVidia drivers, it cannot be used at all.
(3) If the Maxtor drive is attached while using Windows drivers (in UDMA6 mode), it can be used in some circumstances (described as follows).
(4) If the Maxtor drive has no OS installed on it, it can be used fine.
(5) If the Maxtor drive has an OS installed on it, it will hang at boot time.
(6) If the Maxtor drive has an OS installed on it, other drives (being booted from) will hang at boot time.
(7) If another drive has failed to boot because the Maxtor drive has an OS on it, deleting all data/partitions from the Maxtor drive will not enable the first drive to boot.
(8) If another drive has failed to boot because the Maxtor drive has/had an OS on it, unattaching the Maxtor drive will enable it to boot once again.
(9) Once another drive has managed to boot again, the Maxtor drive can be reattached (with data/partitions having been deleted), and it will boot again. If it still has the OS on it, however, it will cause the first drive to hang again.
(10) None of this highly abnormal behaviour is experienced using a Samsung Spinpoint drive (with the same SATA II interface) instead.
What really puzzles me about this is the apparent memory of the system for the previous boot. (7) and (9) above are identical in the conditions of the drives when the boot is made, and the only difference in the situation is that before (7) the previous boot has failed, and before (9) the previous boot has succeeded. How/why that should influence the current boot (after a hard reset, with power down in between to ensure no residual current effects), and why this should interact with the Maxtor drive but not any other drive, is a complete mystery. It's also pretty odd that an OS can boot when the Maxtor drive has ordinary data on it, but will hang if the Maxtor drive has an OS on it.
There is clearly a lot more going on here than any standard version of the way OSs boot and load drivers can account for.

Cannot play .avi files from USB Flash Memory UHYB-064GH

Hi,
I have recently bought a 64gb Toshiba Flash Memory Drive (Stick). It's model UHYB-064GH.
Straight out of the box I plugged the USB drive into my Windows PC.
I'm running Windows Vista.
I tried to transfer a number of .avi video files to the device, taking up about 10gb of space.
I tried running the files (using VLC player) straight from the flash drive. Most of the files wouldn't play.
Only one did but it only played the first 8 seconds of a near 2 hour film.
The counter in the corner only showed the film to be 8 seconds long?!
However the properties section of the file confirmed it was a 1.6gb, 2 hour film...?
I transferred the same video files to a different (old) drive I have and found that it worked fine.
The drive is a FAT32 one.
I don't really know much about these things so would be grateful for any advice
Tom

Try to format the USB flash memory in NTFS format.
The FAT file format supports files up to 4GB but the NTFS format supports bigger sizes.

Msi k8n neo plat and microsoft ie

getting my msi k8n neo plat board running satisfactory , except for one problem . when i got to amdmb.com, i start surfing the site, and after a minute or 2, i get a microsoft ie error, send the error report to microsoft, and then ie closes. what is the problem , is it with amdmb.com site? its the only site that this problem with ie is present, all other sites i don,t have this problem

just tryed using the browser firefox, and it works great. its just ie that doesn,t work on amd.mb, and only that site. wierd problem, never experienced anything like it before. had run a short memtest , no errors. the 6800gt , msi k8n neo plat and amd 64 3400 work great. get some super madonion benchmarks-all default-1024 x 768 32bit- 22,755. i was hoping for 22,000, but exceeded my expectations. can get into the 23,000 + with overclocking the 6800gt, have had it overclocked at gpu-412, memory 1.12. not sure how much more you can increase the numbers, thinking my gpu is close to the limit at 412.had a problem with windvd, it ended up being a configuration in windvd- had to enable hardware acceleration , bingo- worked great after that. got my corsair xms pc 3200 to work at 6-3-3-2 timings. still getting to know the board, there is definately a learning curve to be delt with on this board, but i am getting it to work better by the day.

Help with K8N NEO 4 and AMD X2 3800+!!!

For christmas i got a new AMD Athlon X2 3800+ CPU. System Specs Below.
AMD Athlon 3800+ Dual Core CPU
MSI K8N Neo4 Sli motherboard, nforce 4 chipset
XFX Geforce 7800GT 256 MB PCI-E GFX Card
2X512 MB Corsair XMS 3200 Xtra low latency memory
Antec TruePower 2 550Watt PSU
Now, when ever i'm playing a game, at random time periods, the system will start looping the sound, and after a few seconds it will reboot. When it does this, the monitor will go into standby until it restarts,with the little amber light and everything. It does it more often on some games than others. The memory has passed a 24 hr memtest 86 with no errors, and this is the second psu i've tired and still get the same result. The psu in it right now is brand new. I dunno what to do. I'm tired of not being able to play my games b/c of this. The heatsink on the CPU is stock. Also on the graphics card. Temps never reach above 47C on the processor and 65C on the GFX card. Please help me.

I short of have the same problem.I got my pc about two weeks ago.
AMD 3800+ x2 Manchester E6 (Toledo E6 inCpu-Z)
MSI K8N Neo 4 Sli (came with 3.6 bios upgraded to 3.7 and 2 days ago 3.8)
Sapphire x1600 256 pci e
2x512 Corsair VS512MB400 value select(2,5,3,3,8 1T)
Tagan TG480-U01
The first day after a clean install i runned MSI Live update and it just froze (no other application running) force restart and then the hard disk was gone.Fixed it then updated all the drivers for mb graphics nvidia drivers AMD hot fix and M$ hot fix but still it just freezes.Today there were 2 one when i run MSI live update(??????) and another when using 3Dmark06(froze between tests).
Used memtest for 1 hour no errors no Oc althought when used MSI core cell Oc(bios) in comander mode froze in 1 min.Temps dont go above 41 42 (user mode 7/8 fan speed in core center when in Cool n Quiet temps reach 42 43 even 46 and it keeps the rpm near 1100 1200????????)when running games apps with stock fan.
Whats the problem

K8N Neo PL and USB flash memory

Similar Messages

Maybe you are looking for