K8N Neo Platinum hangs randomly

Hi, I have this mobo (K8N Neo Platinum) with a AMD64 2800 on it.
It worked well for 2 years but now it start behaving bad.
Sometimes after 4-5 hours it freeze completely (like a screenshot) without HD moving or any sound coming out from the soundcard.
Sometimes it simply reboot or bluescreen (I can't read it..too fast).
I thought it was a Power supply problem so I changed it with a brand new one. I even tested the memory to see if it was corrupted in some way, but the memory is ok. Once it happened that memtest86+ freezed, but most of the time I tested my 2 512mb banks I had no problem at all.
I thought it was a problem with my Sata HD so I installed Xp pro on a ide hd, but I had the same problem.
I even tried to work on linux, but even there I had random freeze.
Now I don't really know what to do..maybe is the mobo broken? or maybe the cpu.
Do you have any ideas? I haven't found anything useful on the net .
Thanks,
milo

Before your helpful post, I tried something by myself. I installed MBM5, I borrowed a 12cm Fan and put it near the NB. As you can see from the photo, it's not exactly on the right place..it should go a bit more right against the chassis, but I preferred to put it there temporarily..
When I started it, corecenter said cpu35C and NB29C!.. I started MBM and then played a bit with micromachines4. after that, solitarie and winamp where running..and I noticed that NB is always around 30-35C and the CPU stays around 35-37C. That seems to show that the cpu isn't able anymore to cool as it used to do by 2-3degrees, but that maybe it's because the room temperature is now higher..
The good thing is that it should have freezed/crashed right now!
I could probably try to run something more cpu hungry, but I'm already happy with that. I think I'll try to do some of the thing I used to do when it crashed...like connect an external usb2 hd and disconnect it (in the right way I mean). Usually it crashed after that. But maybe it was a coincidence..
To answer your question:
1. I simply installed the cpu as AMD said. so no grease, but just the pad&heatsink&fan provided by AMD.
2. I don't want to install a new bios..I read that people had so many problems. Next time I reboot I'll write down the version..
3. I installed Nvidia drivers, but I think they are a minimum of 6 months old
I usually think that's not good to upgrade if everything works well..I'll update anyway..
(2 image providers.. I hope at least one works

Similar Messages

K8N Neo Platinum hangs at "Initializing Keyboard Controller" step in POST

Hi Folks,
Here is my system:
MSI K8N Neo Platinum (New in box) (no clue on bios version, as I can't access it yet)
Athlon 64 3200+ 2200Mhz, 640Kb Cache
Thermaltake CL-P0025 Silent Tower CPU Cooler (VERY careful installing this)
2x512MB Mushkin 991460 EM3200 400Mhz DDR (
ATI AIW Pro X800XT (AGP)
OCZ ModStream 450W PS (3.3/28A, 5/45A, 12/26A, 220W/312W)
WD 74GB Raptor
Plextor 712A DVD/CD (SATA)
Here is my dilema: box powers up, POST stops at "Initializing Keyboard Controller". ( I know this because the little lights on the D-bracket tell me so.....:-) I have been on these forums as well as AMD's forums all day now, and have tried everything suggested, except swapping PS. But I think I have an adequate model.
One by one, I have disconnected any sources of possible problems. I have reset my bios too many times to count. I have isolated the MB outside of the case. I have re-seated everything numerous times. I changed Bios battery. I've swapped RAM, and it's positions. Even took it all off. I even bought another K8N from Ebay, and have the exact same results. At no time has the status lights displayed anything different, except for a quick change in color of light number 3 when I do a front-panel reset. Right now I have nothing but the processor on the board and I still have the same result; POST hanging at "Initializing keyboard controller". I have swapped keyboards unplugged the keyboard.
I am leaning toward the processor now. What am I missing? Should I just do an RMA and be done with it?
Suggestions encouraged......
James

Quote from: sincity337 on 04-August-05, 12:22:07
Bowen,
I've got an old Asus P2B that still runs like a champ, although slow by todays standards. You are right about it being rock solid, I have never had a problem with it, not one. As a matter of fact I still have it and I use it for my "linux box". Oops, a little off topic.
Anyway, it looks like MSI received the board today. I will start the stopwatch and see how long it takes to get a replacement board. I'll keep you guys posted.
James
Yeah those boards were the best I've seen. The Intel 865 chipsets are pretty good too. My previous 845 based mobo was nice as well. In the past, using VIA boards have been hit and miss with me. The K8T800/Pro and K8T900/Pro seem to be very stable though...still I would get an nForce 4 chipset over the newest VIA boards.
This is OT but I just received my shiny new BFG GeForce 7800 GTX OC card a few days ago and I was very surprised at it's performance. I was using a crappy Radeon X300 because I needed a temp card until I could buy either a 7800 GTX or the upcoming Radeon X900 XT. My last system I had a Radeon 9800 Pro and it ran flawlessly. I only had one problem with that card and it was driver related to only one game. The game was Call of Duty and that issue was resolved by going down to an older driver, but then ATi corrected the problem with a new driver release. Anyway as fast as the 7800 GTX is, I hated it! The reason is that despite it's awesome speed; the only way I can put it, is that it doesn't run games as smooth as Radeon's do. It was especially bad with Battlefield 2. This is ironic because BF2 is supposed to be optimized for nVidia cards.
It has a bad stuttering problem with BF2 and allot of people have this issue. Some have this problem with ATi cards but most are nVidia users. Even when I set the quality down to the same settings as my 9800P was at, it did the same thing. Other games like Counter-Strike: Source ran fine unless you had bots. Heh, even my slow X300 ran games more smoothly (not faster and at a much lower resolution and quality setting but still smoother) than the 7800 GTX. I sent the card back and I'm getting a full refund. I'm waiting on ATi to release their X900 XT and I'll buy that. What's strange is that prior to buying my 9800P two years ago, I had only used nVidia cards since the TnT2. Well times have changed I guess. Oh well, I guess I had to learn the hard way, but at least this way I know I'm getting the right card!

K8N Neo Platinum - Hangs On "Detecting IDE Devices" at POST

My K8N Neo Platinum motherboard died about a month ago. Not having the time or the patience to RMA it, I bought a new one.
I got the new system all setup. The BIOS version on the Motherboard is 1.4
I have a 200gb SATA (NO RAID) HD setup as my boot device, and I also 120gb EIDE setup as a secondary HD.
With my Previous MB, everything worked fine. I had the SATA drive on SATA1, and the IDE as the Master on the 1st IDE Chain. I also have a DVD Drive and a DVD Burner on the 2nd IDE chain. When I set the system up like this this time, the system just hangs at Detecting IDE Devices. It will never boot into Windows. If I unhook the SATA drive, it detects the IDE drive no problem and tries to boot to it, although it doesn't have windows, so it will not boot. If I unhook the IDE drive, the SATA drive boots. That is what I have been doing for the past two weeks, but I would like to access my 2nd Hard drive.
Any Ideas would be helpful.
Thanks!

another thing is never have any other drives in your set up when loading xp to raid
or it writes the mbr to the ide drive not the sata
hence
it detects the IDE drive no problem and tries to boot to it
you have put the sata raid drive first in bios boot order ?

MSI k8n neo platinum hangs after post single beep

Today I powered off my computer, and when I tried to power it back up the x850 fan just runs at full speed, and never drops to idle and the screen stays dark. If I reset the bios then it will post as far as asking to press Del to enter setup, but freezes at that point. This thing has been running like a champ and this is the first problem I've ever had! I unhooked/unplugged everything but the keyboard/video/ram/cpu. Tried running with four different memory modules in single channel and dual channel but no luck there either. None of the hardware below has been changed in the last six months. Any ideas? TIA!
The indicator lights read:
R G
R G
According to the manual this means:
Testing Base and Extended Memory
Testing base memory from 240K to 640K and extended
memory above 1MB using various patterns.
AMD 64 4000+
MSI K8N Neo Plat Rev1
PQI BH5 512x2
ATI x850 AGP
SATA 10k RPM Primary
Antec P/S

Quote from: flobelix on 07-February-07, 07:09:19
Core2Duo E6400 would be a gain of about 15% compared to 4000+ ( in games 1024x768, no aniso or aa). Quality options and better resolution would shorten the gain. Other applications than games e.g. cinebench would run a lot faster on the C2D. The main advantage compared to the 4000+ would be dual core because many future games will be optimized for this. Question is: Is this worth $272?
With only one 7600GT installed you won't be able to play most of the new games in full detail because of lacking 3d power although Core2Duo installed. The gain of cpu performance will be therefor useless (if main focus is on gaming). 7600GT sli-array would be an option for full detail and using more cpu power but it would also be slower than one 7950GT for nearly the same amount of money spent for 2 7600GT.
1. If you need a gaming pc I'd only buy a new C2D if you can also afford high end vga. Otherwise cpu power is wasted.
2. 7600GT is only an option if you want to save money now and you want a second one later. Buying two now to get a sli-array isn't very clever. Less performance than 7950GT, same price.
3. Buying one gig of ddr2 isn't very clever either. More and more applications need more than 1 gig (for example vista!). When changing to ddr2, change to 2 gig dual channel kit.
4. Getting $300 for your old stuff seems quite optimistic to me.
Conclusion: Save your money for better vga! Take back 7600gt, keep old vga and 4000+, wait for a little time and buy Geforce 8800 GTS. Increase of gaming performance would be unbelieveable. After providing high end vga you can upgrade to C2D in next step and receive a noticeable increase of performance in all kinds of applications.
Hmm.. very good points. I went and read some reviews of the upcoming 8600 and 8800. They are quite impressive for the money. I believe I'll return everything and find a limp-a-long $50 mobo to replace the dead msi. It looks like holding out for quad core with dual SLI is the real gain over my current setup. On a side note I won't be running vista until after sp1 or possible sp2. No tangible benefit to me! What suggestions do you have for a solid performing mobo for the following:
socket 939
4 240pin DDR slots
AGP (My X850 XT is still strong enough for everything I do)
SATA 1.5 (no need for the faster one as I have none of those drives)

K8N Neo Platinum Hangs at BIOS

My motherboard is very weird. This doesn't happen every time, but every once in a while when I reboot or power on my computer, it just 'hangs' at the BIOS screen. It doesn't attempt to boot to any device; all I see is the Platinum logo. The system is not locked up, as I can hit F10 and see the standard BIOS screen that displays about of memory, etc. I'll hit the reset button on the computer or CTRL+ALT+DEL and it usually boots then, but sometimes I have to do that more than once.
I have the latest BIOS version.
Is anyone else having this problem?
Lately it's gotten a lot worse. CTRL+ALT+DEL or the Reset button does not seem to help; it will just reboot to the Platinum screen and stay there. If I power off the computer and turn it back on, then it boots usually, but not always.
I'm seriously thinking of ditching this motherboard and buying a different brand. I've already had to RMA an MSI GeForce6800 and now my MSI motherboard is going bad. I'm not too happy right now.

try doing as ktn3 did (although he had a better pSU) it may help
Quote
Posted By KTN3
hmm after doing some reading I realize that the 6800 needs its own power rail or something. This whole time I had the 6800 and the hard drive on the same one!
what PSU are you using?

Post problem with K8N Neo Platinum

I am assembling a system for a friend and it hangs according to D-Bracket2 on Processor initialization (Led 1:red, led 2:green, led 3: green led 4: red)
Specs
PSU: Codegen 350W ( 3,3V 14A
5V 30A
12V 15A )
VGA: Sapphire Radeon 9800 Pro 128MB
CPU: AMD Athlon 3000+
HDD: Seagate 7200.7 120GB in SATA1-port
DVD: MSI DR8-A DVD Burner
RAM: M-Tec 512MB DDR400
If the problem is the processor it should hang on Power On (all leds red), right?
There's some damage done to CPU fan connector so the sensor wire from the CPU fan might have no connection to the mobo. How about ESD-damage, can it cause this?
Another thing I might have done wrong is connecting front panel connectors.
I am just hoping and praying that the processor is OK and the mobo causes this.

Thanks to RacerX for answering but the problem wasn't the PSU.
Mobo caused it and I replaced it. I think it was the physical damage I mentioned in the first post. I also changed hdd from SATA1-port to SATA3-port but I don't think it matters.
Now everything works fine so +12V/15 Amps is enough.
Does the K8N Neo Platinum hang on Processor Init if it doesn't detect CPU Cooler?

K8N NEO PLATINUM Nvidia nforce 3 250 GB Chipset rebooting - hanging !@$%@#$@

Hi folks,
I am working on the K8N NEO platinum motherboard based on the Nvidia nforce 3 250 GB Chipset.
A couple of days ago I lost my internet connection (broadband). After a couple of minutes it ok again. But suddenly the computer frooze.
After rebooting (button on case) I found out that lots of things couldn't be closed anymore once they were opened. I needed to use CTRL-ALT-DEL to go the the active Tasks. But then that started to freeze too so I decided to wipe everything of the system.
I repartioned and reformated the computer with the win XP PRO CD and reinstalled the OS. I saw immediatly that the system was slower then before and that it did not found the internet connection anymore. I checked the LAN connection and there it sayed that the LAN card was working well but that no cables were connected. This was not true because I dubbel checked them twice. I even replace the cable. It was not my Internet provider neighter because the computer is in a local network and others had no problem to access the internet. So I decided to reinstall and reinstall it again. I reinstalled the system (partioning, formatting) it 4 times. The last time suddenly it found my connection back. Then I installed all updates of windows and I used my live update from MSI to update my components.
I am using live update 3 and updated the BIOS and all other parts who needed to be updated. This was done without the presence of a AV and so on. Everything went well and no errors occured. I received everytime a message with success.
Today my computer suddenly hanged itself again. This already 3 times. Nothing is possible anymore except the boot button on the case.
I also encountered 3 times the while surfing the computer suddenly reboots itself without any warning or message.
What the hell is going wrong here ???
Can aynone give me a clue please ?
Is the motherboard dying ?
MSI live bios Version 3.7.000
MS-7030(K8N Neo Series / K8N Neo platinum)
BIOS version 1.7 (latest version)
Award bios release
2005/05/10

Charly.P
Russ_xp was asking about the Max amps on your power supply should be on label like this:-
Need yours - 3.3v= ??A.5v=??A,12v=??A
luck

K8N neo Platinum Win XP SP2 random system crashes/Blue screen

I have recently built a new pc with the items as listed in my signature. Some of the compontents were new (RAM, HDD and VIdeo) and some were second hand (CPU, M/B, Keyboard and Mouse). I found that when I install WIN XP the system seems ok. But after I install any SP1 or SP2 which are required to run the USB2.0 my system crashes randomly and I get a windows blue screen and an auto restart. in the last week it sometimes lasts a day or so then it crashes. Other times it will crash within 5 minutes of start-up. I found a forum topic about a similar problem the other day but when I went looking for it again I couldn't find that topic. In that topic there were comments about PSU's and their ability to run the K8N Neo Platinum. In my specs are my PSU details. Can anyone advise if my PSU may be the problem or if there is any other problem.
I have made a WIN XP boot disk with SP1 and I have an SP2 disk I was given by a PC shop. If you are able to help or need further info to be able to help please let me know.
Regards
Kewlcop

Quote from: PStang on 18-March-05, 05:14:57
i had random shutdowns and blue screens until i uninstalled core center
LOL!
Yet another reason NOT to use Core Center!
This ought to have it's own sticky - Experiencing random reboots & blue screens? Uninstall Core Center first!

MSI K8N Neo Platinum | system freezes!

Hi,
I recently bougt a MSI K8N Neo Platinum and an A64 3200+ Clawhammer Boxed. I was looking forward to low temperatures and a stabile motherboard, but I haven´t been that blessed yet. During random cpu loads, I get system hang-ups. Wether it´s running iTunes, CS, Sisoft Sandra, FarCry or nothing at all, the system sometimes stops responding.
I´ve updated to 1.2 BIOS, and I´ve downloaded the unofficial 1.33 BIOS from this forum , haven´t tried it yet, though.
MSI Corecenter tells med that the CPU temp gets above 55 degrees under full load. Atually, I had up to 70 degrees until I installed a third case fan. But the sys temp reports from 45 to 50 degrees. And I guess this is the little "MSI"-marked heatsink´s fault. It gets burning hot.
Could the system temp be the cause of my hang-ups?
Hoping for tips and possible solutions.
Btw, sorry for my norwegian-english

Hi,
I recently bougt a MSI K8N Neo Platinum and an A64 3200+ Clawhammer Boxed. I was looking forward to low temperatures and a stabile motherboard, but I haven´t been that blessed yet. During random cpu loads, I get system hang-ups. Wether it´s running iTunes, CS, Sisoft Sandra, FarCry or nothing at all, the system sometimes stops responding.
I´ve updated to 1.2 BIOS, and I´ve downloaded the unofficial 1.33 BIOS from this forum , haven´t tried it yet, though.
MSI Corecenter tells med that the CPU temp gets above 55 degrees under full load. Atually, I had up to 70 degrees until I installed a third case fan. But the sys temp reports from 45 to 50 degrees. And I guess this is the little "MSI"-marked heatsink´s fault. It gets burning hot.
Could the system temp be the cause of my hang-ups?
Hoping for tips and possible solutions.
Btw, sorry for my norwegian-english

K8N Neo Platinum: no video output, long beep and long wait, led 3 green

I have a K8N Neo Platinum for about 4 years without big problems. Two days ago I dismounted teh pc to clean and put a new HD and when I mounted again it did not work.
Problem:
Quote
* System hangs and no video output;
* Speaker keep making long beep followed by long rest;
* D-Bracket LEDs are 3 green and 1, 2, 4 red meaning it hangs somewere near teh keyboard controller initialization;
What I have tried:
With no change:
Quote
* Taken off everything from teh MB and put back only CPU, PSU, RAM, VGA and plugs for power and reset switch;
* Turn on teh MB out of teh case;
* Clear teh CMOS setting JBAT1 and by removing battery;
* Tried all possible combinations of one and two RAM sticks and slots on MB;
* Take out all of teh RAM;
* Take out VGA;
* Take out RAM and VGA;
* Switched VGA;
* Switched PSU;
With little change:
Quote
* Take out CPU: make all four leds red and no beep.
System specifications:
PROC
Athlon 64 3400+
RAM
2x Kingston 512mb ddr400
VGA
nVidia geforce4 mx 440 agp
VGA2
nVidia geforce fx 5200 agp
MB
MSI K8N Neo Platinum
HDD
Seagate SATA 180gb
PSU
Coletek 450W +3.3V~20A, +5V~32A, +12V~16A, +5VSB~2.0A, -5~0.5A, -12~0.5A
I have already had some problems like this before with power failures but magically things worked again. This time was teh same. I got things working some times at random (really random lol) by taking power cables, reseting bios and turning back on but teh problem reapeared when I put HDD back and did not work again when I removed it. Now I can't seem to get it to display anything.
Any suggestions? Thanks in advance.
EDIT: sry I made a little confusion: It is a K8N Neo and not a K8N Neo2.

Quote from: Fredrik on 18-November-08, 05:19:33
Thanks!
Keyboard problem, you think? What do you have?
Two things that are quite common:
Do not attach PS2 keyboard when there is power in the system.
Do attach USB keyboards when you are up and running in Windows.
This is not it, but Logitech keyboard drivers often complicate things.
I do use a PS2 kbd but never had problems with it (unlike teh PS2 mouse). I do not think it's kbd fault because it won't POST with or without it.

K8N Neo Platinum and modded X800 Pro

Hello everyone,
I am running the Board for a while now and it was rockstable.
System is:
A643200+ C0 Zalman CNPS 7000 A-Cu
MSI K8N NEO Platinum Bios 1.2
2x512MB OCZ 3700 EB
windows xp pro sp1
old card: Ati 9800 XT
new card: Saphire X800 Pro modded to XT.
After installing the Card properly, i installed the catalyst 4.8 Drivers and direct9c
After testing a little Bit benchmarking stresstesting, i rebootet and the system and it hangs at the windows xp bootscreen. i reloaded a restore point and tried to reinstall the drivers. no luck.
then i reinstalled windows xp on moday with the same drivers and everything seemed to work fine. windows booted normally, the card worked fine.
yesterday after work. same thing. lookup at the bootscreen of windows.
i uninstalled the catalyst drivers in windows safe mode then rebooted.
normally when i install the card it installs the x800pro and x800 secondary and then finds the rage theater chip and installs it too.
after freezing and getting into windows i can install the card drivers, but the theater chip isnt recognized anymore.
the card is working fine on 3d. i played yesteray for 4 hours at a time and no problems. but after rebooting i cant get into windows.
so i contacted the seller of the card and he told me i am the thired customer who hast issues with the card on this board.
same problem. random freezes on boot sequence, but others seem to have problems in 3d which i dont. i only cant boot.
any suggestions?

Quote
Originally posted by phreakymind
Hello everyone,
I am running the Board for a while now and it was rockstable.
System is:
A643200+ C0 Zalman CNPS 7000 A-Cu
MSI K8N NEO Platinum Bios 1.2
2x512MB OCZ 3700 EB
windows xp pro sp1
old card: Ati 9800 XT
new card: Saphire X800 Pro modded to XT.
After installing the Card properly, i installed the catalyst 4.8 Drivers and direct9c
After testing a little Bit benchmarking stresstesting, i rebootet and the system and it hangs at the windows xp bootscreen. i reloaded a restore point and tried to reinstall the drivers. no luck.
then i reinstalled windows xp on moday with the same drivers and everything seemed to work fine. windows booted normally, the card worked fine.
yesterday after work. same thing. lookup at the bootscreen of windows.
i uninstalled the catalyst drivers in windows safe mode then rebooted.
normally when i install the card it installs the x800pro and x800 secondary and then finds the rage theater chip and installs it too.
after freezing and getting into windows i can install the card drivers, but the theater chip isnt recognized anymore.
the card is working fine on 3d. i played yesteray for 4 hours at a time and no problems. but after rebooting i cant get into windows.
so i contacted the seller of the card and he told me i am the thired customer who hast issues with the card on this board.
same problem. random freezes on boot sequence, but others seem to have problems in 3d which i dont. i only cant boot.
any suggestions?
Load BIOS default to try again.
Maybe you can update the BIOS to 1.42 to try again.

K8N Neo Platinum and Maxtor SATA II 250GB 6V250F0

Hi folks,
Having a bit of fun with this one. After first installing the new hard drive (Maxtor SATA II 250GB 6V250F0) , the BIOS immediately recognised it, I could boot into Windows, and Windows recognised it, and I thought I was in for a smooth ride. Sadly, the good news ends there.
Tried to initialise the disk, but this simply gave an error after a few seconds, and wrote a whole load of controller error messages to the system event log. Since then, I've done the following troubleshooting steps:-
(1) Tried in Normal Mode and Safe Mode, made no difference.
(2) Tried with the jumper on the back of the drive set to limit it to SATA I, as I'm connecting to SATA I controllers on the motherboard. Made no difference with it on or off. Tried a second jumper just in case the first one was faulty; still made no difference.
(3) Tried using different power cables and molex connectors; made no difference.
(4) Tried using different data cables; made no difference.
(5) Tried connecting to each of the four SATA ports; made no difference. Tested each port with another drive ((an older Maxtor SATA I drive, which has always worked fine), and they each worked fine.
(6) Tried with and without another SATA drive (an older Maxtor SATA I drive, which has always worked fine); made no difference.
(7) Checked the drive firmware (VA111630); apparently already the latest.
(8) Used the nVidia registry fix to disable NCQ; made no difference.
(9) Disabled write caching; made no difference.
(10) Ran powermax 4.22 to test the drive, and it reports no problems with the drive at all. Did the full surface scan just in case, and a burn-in test; these also reported no problems. Curiously, they also reported no problems when I did the same tests with the back jumper removed; i.e. running it in SATA II mode when connected to a SATA I port apparently didn't bother powermax. Go figure.
The only way I've got anything to happen with the drive so far is to set it to run in PIO mode(!), which I did briefly, and which enabled the drive to be initialised in Windows. Haven't tried much else in that mode yet, not least because I have no intention of actually using it in that mode for obvious reasons.
So...we have a perfectly functioning disk, attached to a perfectly functioning SATA port, with supposed complete compatibility between them, and with pretty much all other bases covered, and the end result is...it doesn't work.
Has *anyone* got this particular drive model (Maxtor 6V250F0) to work with a K8N Neo Platinum, and if so, how??? ??? ???

Latest Update (this is a real Twilight Zone one ):
LOL, well I should have known better than to be optimistic about anything where this drive is concerned. With Windows drivers installed, it seemed to work okay as a storage drive. So I then installed XP on it, and sure enough it hangs when loading the OS. As the next test, I did a clean install of XP on an IDE drive I have installed, which worked fine (could boot no problems). I then cloned that to the Maxtor drive (the clean OS had no nVidia drivers installed), and not only did the Maxtor drive fail to boot, but so did the IDE drive (even though nothing has changed on that drive!) Both would hang at the Windows loading screen. So then I deleted the partition on the Maxtor drive, so it was effectively back to the situation where the IDE drive booted okay previously (with a blank Maxtor drive attached), but now it continued to fail to load. If I unplugged the Maxtor drive, however, then the IDE drive would boot. If I then re-attached the Maxtor drive, the IDE drive would still boot, even though that would be exactly the same situation in which it didn't boot before the Maxtor unplug and replug. In short, it simply makes no sense whatsoever. ???
A summary of facts/findings:-
(1) System works fine; all components checked and pass diagnostic tests, no Windows problems in the event log or device manager, no random crashes or anything like that. The Maxtor drive passes Powermax tests fine.
(2) If the Maxtor drive is attached while using nVidia drivers, it cannot be used at all.
(3) If the Maxtor drive is attached while using Windows drivers (in UDMA6 mode), it can be used in some circumstances (described as follows).
(4) If the Maxtor drive has no OS installed on it, it can be used fine.
(5) If the Maxtor drive has an OS installed on it, it will hang at boot time.
(6) If the Maxtor drive has an OS installed on it, other drives (being booted from) will hang at boot time.
(7) If another drive has failed to boot because the Maxtor drive has an OS on it, deleting all data/partitions from the Maxtor drive will not enable the first drive to boot.
(8) If another drive has failed to boot because the Maxtor drive has/had an OS on it, unattaching the Maxtor drive will enable it to boot once again.
(9) Once another drive has managed to boot again, the Maxtor drive can be reattached (with data/partitions having been deleted), and it will boot again. If it still has the OS on it, however, it will cause the first drive to hang again.
(10) None of this highly abnormal behaviour is experienced using a Samsung Spinpoint drive (with the same SATA II interface) instead.
What really puzzles me about this is the apparent memory of the system for the previous boot. (7) and (9) above are identical in the conditions of the drives when the boot is made, and the only difference in the situation is that before (7) the previous boot has failed, and before (9) the previous boot has succeeded. How/why that should influence the current boot (after a hard reset, with power down in between to ensure no residual current effects), and why this should interact with the Maxtor drive but not any other drive, is a complete mystery. It's also pretty odd that an OS can boot when the Maxtor drive has ordinary data on it, but will hang if the Maxtor drive has an OS on it.
There is clearly a lot more going on here than any standard version of the way OSs boot and load drivers can account for.

Help! K8n Neo Platinum wont finish posting

I have a k8n neo platinum, newcastle 3200, 1gb corsair 2-3-3-6 ram, Westen Digital 200gb sata drive, and an Antec Truepower 430watt psu. Everything starts up correctly, but after about 30 seconds the board just powers down. I can attempt to reset it, but it powers down after about 10 seconds afterwords. After each time, the power light stays blinking but nothing else happens.
I think this may be related to the wrong newcastle temp readings bug (I was able to power it on long enough to check that my chip temp was 60deg C, but the heatsink was cold). My fan is a Thermaltake Venus 12. I was going to attempt to bios flash it, but I can't even power it on long enough to do that.
Any help would be extremely useful.

Actually, it was a folse positive. Seems that my problem was a keyboard problem of all things. After switiching the power connector around, it still just died when I went to use the keyboard. So I switched to a different keyboard.
I am having another problem though. I'm trying to install an OS (windows xp) and am facing random lockups during the installation. And at times, the keyboard just won't respond in the bios.
Temps are more or less fine, I think. They were toping at 68 deg C (newcastle temp bug). I'm too scared to update the bios and have it just lock up in the middle.
With a new keyboard plugged in, the original problem goes away, but if I set the bios to halt on "all errors", instead of the default "all but keyboard", it post hangs with the error message "keyboard is locked out - unlock the key" which may or may not be related. I would really like to be able to use my other keyboard, but that's even worse.
If anyone could shed some light on the crazy keyboard issues and the random lockups, that would be great. This motherboard is really starting to frustrate me.

K8N Neo Platinum issue, computer does not boot..

Hello,
I’m going to try to be as thorough as possible here… :D
Recently I reinstalled Windows Xp (32-bit version) on my computer to speed things up again like it used to be. I did an updated on the BIOS while I was at it as well, through the Live Update tool downloaded from the msi.com.tw website. The install went well, no errors. The next day while playing WoW the computer began acting weird and computer froze during gameplay. After that the computer had artefacts, strange disturbance on the screen making it impossible to see anything on the screen. So I thought that maybe since the screen looked all messed up it was definitely the graphics card that was about to die and so I sent the gfx to the retailer and they checked it thoroughly for errors without finding any, while they were at it they also checked my RAM and they also came out clean.
A few days ago when my Gfx and RAM came back I inserted them back onto the mobo and when turning on the powerswitch nothing happened… I therefore tried to solve the problem myself and began reinserting all the computer parts piece after piece and well the computer started at least with the fans going and all but after a few seconds it shuts down again.
When I plug in the power cable the PSU makes a clicking sound, don’t know if that’s normal but haven’t noticed it before.
To maybe help you guys when helping me I installed the d-bracket (the usb thingy with 4 led’s ^^) which shows 4 red lights when starting the computer and lasts until the computer shuts down. According to the d-bracket FAQ it means: “- The D-LED will hang here if the processor is damaged or not installed properly or you have a weak Power Supply Unit.”
Well I reinstalled the cpu, put on new thermal grease so I don’t think that is the problem and the computer has been working fine for more than one year until now... How do I know if it’s the PSU or if the cpu is damaged? Could the motherboard been damaged after Live update’s flash? And what could have caused the artefacts on my screen the other day? Errors with the newest nVidia gfx drivers? I’m very confused :S
What should I do?
Thank you for your help!
Computer specs:
Amd 64 3400+ with Zalman cpu fan(can’t remember which one, one with only Cu heatsink + fanmate)
1 GB (2x512MB) Corsair 3200
1x 74GB Western Digital Raptor 10k RPM S-ATA + 1x 200GB P-ATA Maxtor
Gainward nVidia 6800GT Golden Sample 256 MB
MSI K8N Neo Platinum Nforce3 250GB
Antec True 380SP, 380W (came with my enclosure Antec Sonata I, www.antec.com)

Hi again..
I've now received a new PSU from Antecs RMA department. A TruePower 2.0 380W. My computer still doesn't work. 4 Red LED's when trying to boot it up. But I have noticed one thing since last time I wrote here. Remember what I was saying that I upgraded my BIOS through LiveUpdate? When I later checked my motherboard I noticed the CMOS pins around JBAT1(I think) was incorrectly placed. Instead of having them on either 1,2(to keep settings) or 1,3(to clear CMOS) they were placed right next to the JBAT1 pins, on something that wasn't named or explained in my manual. Maybe that is the reason my computer is acting strange? I mean the BIOS could maybe not have properly been saved or something. :/
I'm too inexperienced to know if that had anything to do with my recent computer isssues, but maybe you guys know. Would that screwup by me be covered by my warranty?
If that pins-placed-wrong-on-the-mobo problem doesn't have anything to do with my problem that leaves me with the 4 LEDs from the D-bracket showing a broken CPU or PSU(it's brand new, shouldn't be any problem with it!). So a damaged CPU it is.
Anyone of you got an idea? Been away from my computer for too long. This is getting annoying.
Thanks.
/Christopher

D-bracket2 codes? (K8N Neo Platinum)

hey there, its like this.. i just bought a A64 and a K8N Neo Platinum motherboard.. all worked fine nice bench scores and all was happy indeed!
then i started playing the CSS beta.. 30 seconds later the system dies.. (!?) thinking what the heck now? so i checked the CPU sink it was HOT HOT HOT!! after this the mother board dont start not even a fans works.. if i remove the CPU the system "starts" fans works etc.. now i wounder if the CPU is dead? and where are the D bracked fail codes? cuz when system has no CPU 4 red LEDs are lith.. guessing that meens that a CPU is missing.
any one knows where i can get a fail code description.. have checked the manual, but no luck..
also is this coverd by any warranty? CPU just dont overheat lik that.. had mounted the CPU cooler corect etc..

K8N Neo Platinum D-Bracket LED Combinations
4-Red = system hang, processor damaged or not installed properly
1-Green (top left) all others Red = Early Chipset Initialization
1-Green (top right) all others Red = Memory module damaged or not compatible
2-Green at top/2-red at bottom = BIOS image to RAM for quick boot
1-Green lower left = Initializing Keyboard Controller
2-Green left side = Testing VGA BIOS
Red upper left and lower right = CPU Initialization
1-Red lower right = Testing Real Time Clock
1-Green lower right = Initializing Video Interface
Green upper left and lower right = BIOS Sign-On
2-Red left side 2-Green right side = Testing Base and Extended Memory
1-Red lower left = Resource Assignment
2-Red top 2-Green bottom = Initializing Hard Drive Controller
1-Red upper right = Initializing Floppy Drive Controller
1-Red upper left = Boot Attempt
and all GREEN = Operating System Booting

K8N Neo Platinum hangs randomly

Similar Messages

Maybe you are looking for