K8n-neo-platinum sounds problem

heya guys, i have only had this mobo a few days and am very impressed
i have only one gripe/issue...the onboard sound is supposed to support SPDIF/optical out...now i have a Technics dolby digital/DTS receiver...i have connected the lead to connect the two together.
now the sound is very low quality and skips a hell of a lot...my amp's signal light keep flicking off as well, now the amp & cable are fine as i have tested them with devices that do work fine (PS2 optical connection 5.1 audio stright away), the mother board
i am using latest NForce drivers and am using Bios 1.3
i was really looking forward to using this feature cos my audigy's optical won't even switch on
any ideas guys?
thanks
mike

Check out this thread on this issue

Similar Messages

K8N Neo Platinum sound problem!

Has anyone had any problems with the on board sound?
With a basic hardware setup, I get a faint beep every 2 seconds from my 5.1 speakers when in the BIOS screen, and I get noise whenever the RAM is accessed (Corsair TWINX XMS 3200LL has LEDs on the heat shield and the speakers produce noise consistent with the LED activity). There is a low frequency rumbling noise whenever some active content is displayed in internet explorer, even sliding the volume bar on the desktop produces a rumbling sound!!
I have tried a reinstall with a barebones setup, all defaults in BIOS, but the problem is still there even before windows is installed. I even tried a seperate PCI soundcard, and the problem is still there! MSI say the board is suspect. Am I the first to experience this??

Hey Southmike,
I get the same symptoms whether using a sound card or on board sound. MSI seem to think its a dicky board, also on another forum someone said it was probably the north or southbridge going south (or north!)
I plan to return the board, I've only had the damn thing 2 days!

K8N Neo Platinum - Reboot problems

This is very strange.......
Just bare with me as I try to explain.
I just orderd a new system to build from scratch and all seemed to go ok.
I have:
Motherboard: K8N Neo Platinum
CPU: AMD Athlon 64 - 2800+
VIDEO: ATI Radeon 9600XT - 128 MB
RAM: 1GB DDR PC2700 CL2.5 - SAMSUNG - 1 Stick
SOUND: I also have an old PCI sound card in there.
HD: none connected currently
CASE: XG Viper Gaming Case
On my first boot everything seemed to go ok. I saw the post screen. The CPU, the Memory were all recognized the only thing is I don't have a HD in it right now so there was no OS to boot. I went into BIOS and double checked the settings. I noticed the RT clock was off slightly so I changed it. Looked around and made sure the AGP port was selected as my primary video adapter. Besides that I didn't change any other settings.
When I saved the BIOS settings and the computer did an automatic reboot I got nothing except a repeating "BEEP" and a black screen.
I waited a few seconds (around 20) then turned the computer on and it started up fine again. This time I didn't go into BIOS just let it boot up to the point where it said INVALID system disk. I did a reboot with the same problem - a repeating "BEEP" and a black screen.
A warm reboot doesn't do anything - It only comes back up with a black screen and the repeating beeps. Also If I power down and up too quick I also get no other effect than the black screen and repeating beeps.
The only way to get the post screen is to let it sit around 20 seconds and boot up.
Even If I let it sit over night, boot it up, see the post, and reboot 2 seconds after I get the post screen, the black screen and the beeping occurs (so I am not too sure its a CPU heat issue).
also on a side note the DBracket has some strange lights on it. - IF I am looking at the Dbracket from the right orientation - I think it is giving a "Initalizing Keyboard Controller" error when I get the black screen. It is either that or the Video Interface error. - 3 RED LIGHTS and 1 GREEN LIGHT.
Any sugestions or help would be GREATLY APPRECIATED !!!
Thank you !!!!!!

OK - I pulled out the 9600XT and put in a 9000 saphire radeon card with the same effects.....
when I pull out the Video card and the memory I get the same black screen and error code of course...
second - I put the memory in and left the video card out only and got a signle long beep.. then no additional beeps after that but of course no video...
third - I put in the video card (the 9600 XT) and left the memory out and got the identical black screen and repeating long beeps.
last - I put the memory back in.. booted up fine... then tried to reboot and I was back to the black screen with multiple long beeps..
one interesting thing that I learned from this was - when there was no memory in I got the same "beeps" as I do when I try to reboot with the memory in... could it be something to do with the memory?.... or is it still leaning toward a PSU problem..
(Unfortunatly I don't have access to another stick of memory right now,... nor a sufficient PSU for the system...)
HELP !!!!

K8N Neo Platinum sound NOISE

Hi
This is the most stable system I ever had BUT, I don't know if this is a problem with the onboard sound but I'm getting allot of noise through the sound card. Hisses, beeps and buzzing noises very annoying... It increases when XP is booting/loaded. I even get little beeps when I'm in the Bios...
I have tried moving the cables away from each other even moving & shielding the mains cables, muting the various inputs & outputs in Win XP and disabling the sound in the bios I still get the noise! Oh, and I’ve tried it through headphones... So it’s definitely interference with something inside. I was thinking the graphics card…
So, would I be better off getting a separate PCI sound card (e.g. SoundBlaster)?
Can anyone help??
Thanks
Tony M
K8N Neo Platinum (MS-7030)
AMD A64 3000+ Newcastle (Boxed HS&F)
1GB (2x512) RAM
Inno3D nVidia GF6800
2x NEC DVD-RW-DL
74GB Western Digital Raptor
80GB Maxtor DiamondMax +9
Hyper Type R 480w PSU
19" BenQ LCD monitor

Okay.
I got a loan of a SB Audigy and stuck it in.
No more clicks, beeps or buzz noises. Yippee.
Thanks for all your help.
Tony M
K8N Neo Platinum (MS-7030)
AMD A64 3000+ Newcastle (Boxed HS&F)
1GB (2x512) RAM
Inno3D nVidia GF6800
2x NEC DVD-RW-DL
74GB Western Digital Raptor
80GB Maxtor DiamondMax +9
Hyper Type R 480w PSU
19" BenQ LCD monitor
SoundBlaster Audigy

MSI K8N NEO Platinum Edition PROBLEM

Hi (my english is not good sorry for that)
I just got my new computer:
MSI K8N NEO Platinum Edition
AMD Athlon64 3200+
Western Digital Caviar 160Gb
PNY Verto GeForce 6800Ultra 256Mb
1GB Value Select pc3200
Levicom 500W
The Problem is that when i start the computer, it boot and die directly no bootscreen what so ever, it boot and die. i dont know what to do plz help me

Make sure you have Both the ATX Wires on.. theres the Big one! (21Pins i think).. and the Small 4Pin Connector both need to be connected.. if you havent done so yet.. Another thing you could do is Take everything out and place it on a cardboard or something appropriate for the mobo.... I think your motherboard is shorting?.. if it's touching your case.. I had somewhat the same issue long time ago.. give it a try..if you want hope it helps..

MSI k8n neo platinum post problem

I just bought a 2nd hand K8N neo platinum and I can't get it to post, I have reduced down to 1 stick of ram(tried all slots) vga and cpu running out of case. I have an ultra 600 psu that certainly should be doing the buisness as everything was fine on an NF7S-V2 up until 1/2 hour prior.
On the led device it's starting 4 red then after a couple of seconds it goes 1 red 2 red 3 green 4 red which I found relates to keyboard controller. I've tried with various keyboards but no joy. I get nothing on the screen at all but that's the next stage in post.
My memory is Twinmos 3200 twin x 2 x 512 double sided, which I saw in the sticky can be troublesome.
Any body got any ideas?

i am having an almost identical problem.
First the system wont go past post,then i realised it would but only boot if i had the USB mouse unplugged (i noticed the d-brackets lights changed after i unplugged the mouse)
then i was able to get to windows, however i couldn't do much (mouse wouldnt detect if replugged, keyboard not detected - all lights off)
So i tried clearing the CMOS
now i am having the same problem, except this time i get CMOS checksum error - defaults loaded
then it tells me to press f1 to continue to del to enter setup, which i cant do since the keyboard wont work. so now im totally bamboozled
I've tried changing the PSU as well with no luck (both were 500watts)
Funny thing is, the pc having the problem is identical to the pc im writing on now, presonally i think the motherboard is not v good, since alot of people have this problem or similar to it. (and yes im using the keyboard and mouse now, that i tested on the other pc)
SPECS:
MSI k8N Neo Platinum
Powercolor Radeon 9800 Pro
AMD 64 3000+
1GB Geil Memory
Maxtor 160GB
500watt Magna Dual Fans
Will check what the D-bracket says and will report back.
ok here goes:
(with usb mouse plugged in)
1= green
2= red
3=red
4=green
(without usb mouse plugged in) - but bare in mind i cant press f1 (no keyboard) to continue else i would probably be able to get to windows.
1= green
2= green
3=green
4=red

K8N Neo Platinum reboot problem

ok, spec:
MSI K8N Neo Platinum mobo
A64 - 3000+
2 corsair 2700 256Mb in slots 1 and 2 - 1 unbranded 2700 in slot 3 (all memory double sided)
Powercolor ATI Radeon 9800 Pro
SATA WD Raptor 74Gb
EIDE 8x Hitachi DVD-ROM drive
550W PSU - "Channel Well technology" - 24a@12v 40a@5v [email protected]
that's it. it posts ok, has frozen there once tho. but every time since then post is ok. Installed WinXP fine - until the install process tried to reboot into WinXP proper - where it continually reset itself until eventually it got in - and reported it had rescued itself from a serious error - I can sit in windows seemingly indefinitely - using the hard-drive to browse through the windows installation. now the problem is when I instert a disc into the dvd drive the computer tries to read it - little disc icon on the arrow etc. then it hangs and the computer resets.... any ideas?? the computer shop I got the PSU from says my configuration is "categorically" not using 550W of power - what do you guys think?
thanks for any help, cheers
Niall

Quote
mobo drivers -> SP2 -> graphics card -> Dx9
Wrong order s/be
Sp2 (includes Dx9)
Mobo Drivers
graphics card
Dx9 needs to be installed prior to the mobo drivers.
This applies to the Gart (Agp Controller)
If you haven't done so downloadWindows XP - Unified Driver Version: 5.10 & install.
Device Manager System Devices note the AGP Host to PCI Bridge Device this is the Gart driver
you should see a diff in graphics performance

K8n neo platinum boot problem

hi all
first of all sorry about my bad english...
my pc specs
A64 2800+ newcastle with Tt Polo735
k8n neo platinum
Noganet 350W (+5v=35a // +12v=15a // -12v=1a // -5v=0.5a )
2x Wd30gb
sapphire9600xt
256mb kingston pc2700
256mb xerox pc2700
well, yesterday i changed my amd box cooler and put the polo735.. everything was fine.. when i turn on the computer..dont boot and only a single bip every 4 or 5 secs..
i tryed everything, another mems, another vid card... i started my pc with only mems, vid and heatsink and nothing...only the beps
i put my cpu on another pc and works fine.. and put another cpu on mi mother and the same problem..
i clear cmos and nothing
i change the psu for a generic 520w and nothing
plz HElp
cyas
EDIT: DBRACKET led 1, 2, 4 in red // led 3 in green

Sounds like bad/not levered pressure from the new heatsink to the cpu HS .
Make sure it correct aligned and the right way and has the correct pressure
to the cpus heatspreader . Also make sure motherboard can read the fans rpm .
[edit:]
btw i agree with bas , your current psu is weak .
The polo fan also is a very watt hungry fan compared to boxed .

K8N Neo Platinum Weird Problem

Hi.I just got the motherboard yesterday. The spec is:
Athlon 64 3200+
K8N Neo Platinum
512MB Crucial DDR 266
Enermax 350Watt PSU
Now my problem is an odd one. I start up my PC, and everything is fine, XP boots etc. However. when I turn the computer off, the power light will have a flash at the front, the light stays solid for a few seconds, disappears, and comes back on. In this state, when the power switch is pressed, the computer does not come on and the light continutes to blink. The only option is to turn off the PSU, wait a minute, then turn the PSU back on and the PC will be fine. When I restart from windows (Start--> Restart), everything works fine.
I am using the latest BIOS, I was thinking that it maybe something to do with Power Saving, is there a way to totally disable it?
Thanks for your help, it's REALLY annoying me.
P.S. Are USB keyboards meant to work with the latest BIOS? Mine doesnt seem to want to.

hi edjam,
welcome to forum.
1) Quote
that it maybe something to do with Power Saving
your right it does
1-1)1st look at control panel - Power Options - Advanced tab - Power buttons at bottom. check what set there.
1-2) When your computer does this try keeping the powerr switch pressed in for a time 4-5 seconds see if this makes any difference.
1-3) Check in bios - Power Management - Power button - that it is set to power off
2)Quote
USB keyboards meant to work with the latest BIOS?
I believe so
Enter Bios & check in onboard Device USB Mouse Support is enabled

MSI K8N Neo platinum sound prob

Hi!!
I got myself a MSI K8N Neo platinum...
every 20 secondz my music hangz...
why? don't ask me.
any answers? and when my music hangs I have a look at the ctrl+alt+delete menu and I see that my cpu load goes to 46 percent when the music stops...
help...
cheerz Xyus!!

Hi!!
I got myself a MSI K8N Neo platinum...
every 20 secondz my music hangz...
why? don't ask me.
any answers? and when my music hangs I have a look at the ctrl+alt+delete menu and I see that my cpu load goes to 46 percent when the music stops...
help...
cheerz Xyus!!

K8N Neo Platinum 7030 Problem

I have a K8N Neo Platinum and as of the past week my computer has been acting really strange. I has had random lockups that at first made me think it was the video card. That wasn't the case. I tried a different power supply and that didnt help. So I decided to take everything out of my computer. I had everything unplugged from the motherboard power, ide cables, etc. I noticed as I was taking everything out that I felt like I was getting shocked by my case but I don't know how because I had no power supply in my computer and all the cards, processor, memory were taken out. When I took the mb out i didn't feel the shock anymore, but when I put the mb back in the case and hooked the power supply back up to it I did. I even vacuumed out the case totally removing all dust and dirt. Am I missing something here? HELP lol

thanks for replying glenn after 2 days of hunting i can now say
90% sure the whining is from the powersupply
using my advanced hearing device i found a flaw in its design. before i would put it near psu but not hear the whine from there. well it occured to me to tilt it ever so slightly (tip from radio broacasting in college) to let the noise in but block any wind from crossing the end of my tube. and ch ching finally from the rear of the psu is where it is loudest.
ive owned 3 enermax and theyve been the best psu ive ever owned. but this weekend im swap it with my other and see if it still happens. it will probably take 2 hours total do it which is why ive put it off this long. ive tried bumping the wires around even though its a full size chieftech with all my watercooling gear its almost impossible to not have the wires overlap each other at least a few times. but with the moving around i did do it didnt help.

MSI K8N SLI Platinum sound problem

I've recently installed Windows vista anda i have a problem with my onboard sound, in this case the SB lIve 24! that comes with the msi k8n sli platinum board, i've tried the soundblaster beta drivers but they didn't work, so if anyone knows where i could find a driver to solve this problem, it would be nice
Thanks for your help!!

http://us.creative.com/support/downloads/download2.asp?MainCategory=1&Product=10315&dlcentric=10005&Product_Name=Live%21+24%2Dbit&filetype=1&OSName=Windows+Vista+32-bit
This is the 32bit version of the driver of k8n-sli Platinum mainboard (I have one)... if you want the 64 bit version, just search in the creative support site. Enjoy!

K8N Neo Platinum DMA problem

I uprgraded my old PIII with the following system:
AMD 2800+ (Sempron)
MSI K8N Neo nforce3
512MB Kingston DDR400
Windows 2000 SP4 (with default windows IDE drivers)
WD 80JB (connected with an ATA100 round cable)
LG 4163B (DVD-RW) (ATA33 cable)
I did a clean install of windows but the default value for the the DVD-Writer was PIO mode. I put that drive on DMA mode though the control panel.
Now everytime i try to copy files from the DVD-Writer to the hard disk the system locks and i have to reset. When i switch back to PIO the drive works fine but very slow of course.
The BIOS dma settings are all set to auto... there are only 2 options i think - auto and disable.
What could be the problem here?

Quote from: klickitatdave on 11-October-05, 03:51:15
Did you mean ATA 133 rather than ATA 33? If you are using an ATA 33 cable that could be a major problem. Also, what is your setup, do you have your optical drive on the same IDE channel as your hdd or on a separate one? Do you have the latest firmware installed on the optical? Also, I have found that my K8N nforce 3 Platinum board is very sensitive to IDE cables, (cable that worked and continue to work in my other system will not work in the MSI for some reason). Just some thoughts.
Yes it's an ATA33 cable from my old PC, since the motherboard only had one IDE cable included.
I have the DVD-Writer as secondary master (with latest firmaware) all alone in the IDE channel and the hard drive is on the primary master.
I'll buy a new cable and try it out. Lets hope that's the problem.

K8n neo platinum driver problem

i have got a kn8 neo platinum nforce 3 amd 64 bit motherboard and on a game armada the graphics go funny so i have been told to update drivers for graphics card fx5900xt which i have done and also update the unified drivers version 5.10 but when i install the unified drivers my usb ports do not work i have service pack 2 installed anyone got any ideas...i have to reset my bios on the motherboard to get the usb to work.

Hi Jas
Welcome to forum,
to help people help you its good if you can put your PC details in your signature (See Profile Button Top Left - Then Edit Signature). This means U only do it once & its there for every post.
What version of windows are you using your problem may be linked to Syar2003's post in this thread Woke computer from Sleep: USB doesn't work
see if thats relevent 1st

K8N Neo Platinum & Firewire Problem

dear forum,
I just changend from a siemens D1607 to Neo K8N and I'm very happy with it,
however I habe problems with the firewire device.
It is enabled in the bios and it is recognized by win xp (it is show in the device manager (1394)..),
but when I plug in my terratec aureon firewire soundsystem (I have installed that drivers before..) nothing happens.
I tried with and without sp2, I have installed xp again..i don't know what do to now!
some other facts:
- I use the msi nforce driver package which was with mainboard.
- the soundsystem worked well with the D1607 and my notebook.
some ideas??
thanks very much for your help!!!

I can use just one firewire connector.
there was no additionally firewire bracket (only usb2..) with the mainboard, so I don't use the other connectors on the mainboard.
In the device manager I find the via firewire device+the 1394 network device, but no audio device.
yes, the audio system works fine. before I started with neo k8n I had used it sucessfully in my siemens-fuijutsu D1607 mobo.
I think I will buy a pci firewire card and see how it goes...:(
thanks for your reply!

K8n-neo-platinum sounds problem

Similar Messages

Maybe you are looking for