K8N Neo Platinum USB Keyboard Question

I've been having problems with my Logitech PS/2 keyboard (mobo powers up, then immediately shuts down and requires power be disconnected before restarting). My office PS2 keyboard seems to work fine, so I will replace my current keyboard. I see that some here have better luck with USB keyboards, but when I try a USB board it isn't recognized until Windows loads. I have USB keyboard enabled in the BIOS. I haven't gotten around to fixing the front panel USB ports, and the D bracket ports don't work either, but the main ports work fine. If I did the wiring change for the front panel ports, would a USB keyboard be recognized earlier in the boot sequence, or should I just stick with a PS2 keyboard?

I just fixed my machine so the USB Keyboard and mouse work properly. I have a MSI K8N Neo Platinum (BIOS 1.4 8/27/04) and an Antec Sonata case. When assembled, the two front USB ports and the two D-Bracket 2 USB ports were not working. Also, I was unable to access the BIOS with the USB keyboard (worked fine with a PS/2, though). The four USB ports on the Motherboard were not enabled until after WINXPPRO(SP2) started to load (NUMLOCK light and optical mouse would light), preventing me from accessing the BIOS.
The cause of this problem was an extra black wire in the Front USB Port connector from the case. Once I removed the wire from port 10 on the case connector, all 8 of my USB ports worked fine. I am now able to access the BIOS with the USB keyboard (once I had unplugged and then plugged it back in) and my mouse shows power as soon as I power on my machine.
Cheers,
Tim
12/5/04

Similar Messages

K8N Neo Platinum USB Keyboard

Hi, finally got my motherboard functioning yesterday One strange thing though, when booting the system, could not enter the bios setup since the keyboard was not functioning (it's a keyboard with USB connector). I attached a keyboard with PS/2 connecter to the pc and checked the bios, thinking that USB was still disabled (which it wasn't). I restarted the system with the usb keyboard attached to it and XP came up without any problems, keyboard functional and all (It's a logitech keyboard).
Still when I start the system, the keyboard (although no error message is generated) is not functioning until such time the windows environment is running, after that, I have no further problems.
Is this a known problem to somebody and if so, is there a way to resolve this?
Thanks for your assistance

Thank you all for the replies to my post. I got this hunch that it might have to do with the way the Logitech wireless keyboard interacts with the startup sequence. So I decided to use a conversion switch PS/2 -> USB onto the normal PS/2 keyboard connection and it worked!. Apparently the boot sequence doesn't like a wireless keyboard

Msi k8n neo platinum ps2 keyboard problem

Hi. I'm having issues with my msi k8n neo platinum motherboard. I've read about 50 posts on these forums regarding the supposed ps2 keyboard issues with recent msi boards. However none of them seems to address my current situation.
Like many others, when I power up my system the cpu fan spins for like 3 seconds then everything comes to a halt.
I tried many things to get my system to boot and the only thing that works is plugging my ps2 keyboard into the ps2 mouse port and moving the ps2 mouse into a usb port with an adapter.
It seems there's no hope for fixing the problem other than RMA'ing, but I thought I would add to the pile of complaints stacking up against the MSI boards.

if u had read the threads a little more u might have found a solution that seems to have worked 4 many - a usb keyboard usb Keyboard if u go this route dont forget to enable usb kb in bios
Edit: This Thread Summarises the situation PS2 keyboard/mouse causes random shutdowns or doesnt work

K8N Neo Platinum USB ports turning off?

Hi there,
I've had a K8N Neo Platinum board (in an ANTEC Sonata case, Athlon64 3200+) for a quite a while now and it recently developed a troubling new problem. Every now and then, the all of theUSB ports will simply shut off, dropping whatever devices happened to be connected to them. I have a USB keyboard and mouse, so this is a bit of a problem... If I connect a PS2 keyboard, I get a keyboard back, but it's not a realistic compromise. Also, once the ports have been dropped, trying to inspect them in Device Manager hangs the machine.
I've read through the forum and see other problems related to USB ports with this board, but nothing quite like this. I have already performed the cable snip trick for the front USB ports on the Sonata case (quite a while ago in fact, and it worked nicely) and I've already gone in the devices and turned off the "Allow this device to be turned off to save power" option. Any other ideas on what to check?
I recently added two new USB devices to the machine: an Apple USB Pro keyboard connected via a Geffen USB KVM, and the USB hub that's sitting inside my Dell 24" LCD. I'm going to try disconnecting the Dell's USB hub to try and eliminate it as a problem, and if that doesn't do it, I'll try running with a PS/2 keyboard for a while.
Anyway, if anyone else has seen this problem, I would love some assistance in fixing it.
Thanks,
--ben

AFAIK, there is no 1.B bios for the Neo Platinum (MS-7030), only for the Neo2? Am I mistaken?
http://www.msi.com.tw/program/support/bios/bos/spt_bos_detail.php?UID=572&kind=1

K8N Neo Platinum, USB devices keep losing power

I have a K8N Neo Platinum with a 3000+ AMD 64 chip...
I have a USB problem whereby my wireless USB adaptor just keeps losing power, when I look at the adaptor itself all the power has gone and no lights are on. Unplugging the device and re-inserting it does not get any response from windows. Also, after this has happened, my other USB devices (ie mouse) continue to work fine UNLESS I unplug them and re-insert them. If I do this they also will not power back up. I've tried various adaptors from Netgear and alll of them have the same problems, its like they are causing the USB on my system to fail.
This happens with both the motherboard rear ports and the case front ports and is really driving me mad. Running XP Pro SP 2
I have this problem a couple years ago, and now I've gone back to using the same machine after a reformat the same is happening again. I've installed the latest nFoce drivers and in device management I've turned OFF power management for the USB Root Hubs but it's still happening.
Any ideas?

Check to see if there is a wire running from your Front USB ports to the #10 slot of your USB block which connects to the motherboard header.
USB connector block layout which corresponds to the pin layout on boards with the Intel spec for USB. Do not cut the pin on the MOBO. You are removing/cutting the wire to the connector block from the case.
2 4 6 8 10(this wire, #10, not needed)
1 3 5 7 9(filled/key)
If you find a wire leading to the #10 spot on the block, remove that wire. My block has tabs so that you can pull the wire out, or you could snip/cut the wire leading to that position--if you cut the wire, be careful to cut the correct one and cut it in such a way that it may be repaired if you make a mistake. Make sure you wrap the wire, the exposed end/s, you remove/cut with electrical tape so as not to accidentally cause a short. I actually folded the wire back and wrapped it.
2 posts to read--Here and Here.
This seems to be a common issue involving many different case manufacturers. I don't know how it applies to other MOBO manufacturers, but in these forums it is not limited to a specific MSI model or supported chipset(Intel or AMD).

MSI K8N NEO Platinum Edition memory question

Hi there,
I've currently got a MSI K8N NEO Platinum Edition (Nforce 3) motherboard and 2X 512 MB Corsair Value Select memory modules (both double sided) running at DDR 400 - this runs completely stable and has done for a number of months. I would like to increase my memory to 1.5 Gig but there seems to be a lot of issues?
I originally planned to buy an additional 512 Meg Corsair value select chip and place it in Bank 3 - is this acceptable?
I assue that i would have to drop the speed down to DDR 333 from 400, could anyone tell me how much of a difference this actually makes (when playing FPS games Doom3 etc..) ?
Any help would be greatly appreciated as i've been looking through both this forum and the Corsair one and i cant seem to find the answer.
thanks in advance !

Just note that there are combinations of two sticks that will also make the board run in DDR333 mode (see page 2-8 of the manual). For example, using two double-sided sticks in DIMM2 and DIMM3. I've actually managed to get it to work at DDR400 in those two slots, but it's not perfectly stable and overclocking diminishes drastically. Bottom line is the system will work fine when forced to DDR333...as long as you don't expect to overclock the RAM to any significant degree.

K8N SLi Platinum USB keyboard boot issues

Hello, I have a K8N SLi Platinum connected via an Aten US221 USB switch (http://www.aten-usa.com/?product&cat=804&Item=US221) and a Kensington USB hub to a Logitech MX518 mouse and a Logitech multimedia pro keyboard. I use this to connect the same two input devices to two computers and toggle. Previously I used a keyboard to each, with a Dell PS/2 used on the MSI motherboard.
The problem is that the MSI motherboard fails to detect the keyboard every other boot or so. It doesn't matter if I unplug the Aten switch, the USB hub or even connect it directly to the USB root hub. The only thing that solves it to restart the MSI computer over and over until it decides to start working. And I need the keyboard since I have a bootloader (GRUB) that I select which OS to boot with. The switch and keyboard works without a hitch on an older Dell computer which is also connected in tandem.
Since I need both mouse and keyboard on a single wire I cannot use a USB-to-PS/2 connector. I've found several posts here which suggests this motherboard is buggy, if that's the case shouldn't MSI issue some sort of BIOS patch?
Sincerely, Martin "xarragon" Persson

Might work.
I don't like the inconsistency you describe: working sometimes and after a lot of reboots. Would you say your system parts, please. Troubleshooting this in your end must include finding a situation where it never works, and when it always work. For example, if you don't have the mouse connected at all, if you don't use the hub, etc.
Not saying motherboards can't be damaged, specially port end, but the hub thing is a more likely culprit.

Neo platinum & USB keyboards

peeps i,m facing this weird kinda problem with my HP usb multimedia keyboard when i hook it up with my neo platinum, its that each time windows starts i have to plug it out and plug it in again to make it work otherwise there is just no power in it, everytime i have to make it to be detected, i have re-installed windows and update bios, i have enabled usb keyboards and mouse support in the bios but no avail
secondly, i cannot enter the bios with this usb keyboard, have to hook a ps2 keyboard when i have to enter bios, can someone help please?

Quote from: Tiresmoke on 13-March-05, 00:15:01
When I bought my board I sis some research on it before I purchased. At that time it did not work aty all with MS mouse Opticals. No rythme or reason they just did nor work. I bought a logitech with my board. I got my board all set up and low and behold it did work with the MS mouse.
The moral of the story is sometime they do and sometimes they don't. No reason. Worst case is you need to buy another keyboard. They are cheap items. I feel your pain.
Yeah, usually there's some sort arcane software/hardware conflict - but it's usually been my experience that the included software bundles just rot. I never use 'em anymore.
But that's just me....

K8N Neo platinum usb problem

Hi all i am new to this forum but anyway heres my problem
i was surfing the net when all of a sudden my btvoyager 1010 wireless adapter disapeared i haven't had a problem with this board till then, so i rebooted my pc it said in the task bar usb divce not regonised so i reinstalled the software but when i was promted to plug the wireless adapter back in it came up usb divce not regonise again so i tried it in a different usb port this time it worked fine. the old port will now not regonise anything apart from my pen drive which it works perfectly for, i am not sure why this is happening but i think it somthing to do with the mobo. Also one of the usb ports in the front of my case has stopped working altogeter the headers are plugged in properly but the port just acts dead, the other port in the front of my case works fine which is on the same header what could this problem be. the rest of the coumputer seems fine, i am writeing this on it.
Please Help
Danny

Quote from: The_Guy on 23-November-05, 06:22:28
the port...started working but when i plugged anything into it windows said "usb divice unregconised"
...then tried switching the headers
...the front usb ports then started working properly but the usb ports on the pci backpate...one of them started doing the usb device unrecgonised in windows like the front usb were doing before
So after swapping the connectors over, the problem is switched from front to back. In other words the problem stays put as far as the board is concerned - it remains with the same pinheader (JUSB1 or JUSB2). That means we can discount the device itself, the cabling, the BIOS (there is no JUSB1/JUSB2 swtich), the drivers, etc. It suggests instead that the problem is on the board itself. Maybe a damaged pinheader or something.
You said the thing was loose so maybe it got damaged while for some reason the connector was knocked out? Or it was loose because it was never connected properly in the first place due to a damaged pin? I'd study the pins & see if you can see any physical deformity. If not thenthe problem may be in the circuitry on the board and that's bad I'm afraid.

K8N Neo Platinum - HTT Multiplier Question

Isn't this board supposed to have a 5X multiplier for Hypertransport?

S754 boards/cpu is specified to 800mhz(HT=4x200) 1,6ghz double rate , S939 to 1ghz (HT=5x200) 2ghz double rate.

Newb Question MSI K8N Neo Platinum.

okay i have my parts coming in for my first build ever(i'm nervous, but anxious at the same time) and i just got my MSI K8N Neo Platinum today, all the other parts will come in the next couple of days, cpu arrives next week i believe, specs:
Antec P-160WF
OCZ 520w
Athlon 3400+
mobo(above)
1g corsair
160 Samsung S-ATA HD
I've been going over the mobo manual and i'm confused. I'm not familiar with raid and never had a sata drive, do they go hand and hand? Meaning do i have to set up a raid to use the s-ata drive or do i just plug the sata drive into the mobo and everything will work, loading up windows xp and all? I don't want to use raid, but do i have to? i'm trying to make this build as simple as possible since it's my first time, i know this is probably a dumb question, i'm just new at this.....don't be surprised to see more dumb questions in the coming weeks! thanks.

Quote
Originally posted by onebyte
>>Meaning do i have to set up a raid to use the s-ata drive or do i just plug the sata drive into the mobo and everything will work, loading up windows xp and all?
In a word, no.
I've just fired up my first homebuilt last night. Joy! It's all went perfect on the first power-up. I'm in a similar position, and have a single SATA Hitachi Deskstar. Although I've not yet installed an OS, my understanding is that the Serial ATA interface will work just fine with a single drive. No multiple drive RAID is needed.
My understanding is that all you have to be sure to do is load the SATA drivers from the included diskette, by pressing F6 on boot up. Otherwise the drive won't be properly recognized by the bios. I haven't done this yet, and its still showing as an IDE drive in some places of my bios setup.
If I had it to do over again I doubt I'd spend the extra dollars to go SATA with a single HD. It adds another level of complexity in transferring things to the new machine, and - according to certain authorities -- doesn't really add the extra performance over an ATA 133 that I first thought it would. At least with a 7200 RPM drive, it seems that the 150 or 133 limits never come into play, as the drive's mechanical limitations are less than both... so it's not a bottleneck.
I'm still trying to decide the best way to transfer my Win xp OS and other MS Office programs and updates. I'm not sure if I can clone my PATA HD to the SATA, or if I do what problems I'd have to fix. I've been thinking about transferring a Ghost or Acronis True Image to the new machine and then doing a WinXP repair install to see if I can get everything working with a minimum of time and effort. I'm not sure what to expect, or if it will even work at all. Or if it does, if it will leave me with problems (registry, drivers, etc).
We'll soon see.
Good luck with the build. The only real headache I had, other than getting the HSF uniit on the processor, was trying to connect the case front panel wires for the USB, Firewire, and Audio out and IN jacks, to the mainboard headers. The case wires were single pins and were labeled differently that the MB header block pin assignments. I finally gave up on the audio and firewire, and just used the USB connections after modifying them -- removing the two extra ground wires on pins 9 and 10.
Just take your time and follow the directions. Spend some time looking at the way the heatsink and fan connect onto the processor. Doing that without messing up the thermal compound can be tricky, and the directions from AMD could be clearer on that score.
Again, good luck,
thanks for the info, let me know how it goes...by the sound of what rainz said it seems you don't need to put in that 3.5" floppy disk that came with the mobo, is that right, rainz? Let me know how your OS installs onebyte, i'm curious to know if the SATA gave you trouble or not, wish you luck!

Wake on LAN/Keyboard wake for a K8N Neo Platinum - how do I use this?

I've got a K8N Neo Platinum motherboard that I am using in my home theater PC and I was hoping to enable either the wake on lan or keyboard wake functions so that they could be controlled via a remote control. For now disregard what the overall outcome I want to achieve is... what I want to know is if enabling the WOL and/or keyboard wake function will allow me to turn on the PC from a completely powered down state as opposed to just powering up from a sleep/hybernation mode. I have read people with other motherboards have been able to power up by using their keyboard, mouse or even WOL when the computer is totally shut down. I'm trying to avoid leaving the PC in a sleep/hybernation mode due to electricity usage. Does this motherboard have the ability to power up when the whole system is shut down?
Also, what key on the keyboard is used to wake up the computer? The manual and bios instructions say nothing about what key needs to be pressed to wake it up.

I know you can set various wake options in the bios. Check there!
You can wake up the computer by wriggling the mouse or pressing any key, if the options are enabled in the bios.
Hope this helps

Turn on PC with keyboard [K8N Neo Platinum]

Is it possible to turn your pc on by pressing a button on your keyboard? I have a friend with an old pc (1,5 ghz P4), and he claims that he can turn his pc on that way.
So technically I'm asking you if you know how to do that. Is there a BIOS option in which you can configure the keyboard button on which your computer will respond and go on automatically? That would be very handy.
My motherboard is the K8N Neo Platinum with a 3000+ socket 754. He has an ASUS motherboard.
Thanks.

Check the manual. It should be an option in the bios. I have it in my bios for my board, but when I helped someone put together their machine with a K8N Platinum 2, I didn't see this as an option in that bios. It may be that power on by keyboard and/or mouse is not an option for your board.

K8N Neo Platinum Bios 1.3 XP 3700 heat question

i did do a quick search on here before posting this question but had a load of varying answers ... so
i have a K8N Neo Platinum Bios 1.3 an xp 3700 and core centre says the chip is at about 45 - 50 degrees when the pc is idle
this is with the stock fan that came with the chip and ive also tried a samurai heatsink and fan .... ive reseated and reapplied artic silver and also tried thermal pads as well and the temp on the processor always comes back as 45 ish degrees
is this normal as the pc seems to run ok and even after round of doom 3 the temps only seem to hit about 55
are these chips hotter now or is it a bios / thermal temp issue
cheers guys
ohh and nice forums BTW

yup, issue with temp reading -> 1.43 beta bios for K8N NEO pL. for me 36-39 idle 42-45 after a doom3 session

K8N Neo Platinum hangs at "Initializing Keyboard Controller" step in POST

Hi Folks,
Here is my system:
MSI K8N Neo Platinum (New in box) (no clue on bios version, as I can't access it yet)
Athlon 64 3200+ 2200Mhz, 640Kb Cache
Thermaltake CL-P0025 Silent Tower CPU Cooler (VERY careful installing this)
2x512MB Mushkin 991460 EM3200 400Mhz DDR (
ATI AIW Pro X800XT (AGP)
OCZ ModStream 450W PS (3.3/28A, 5/45A, 12/26A, 220W/312W)
WD 74GB Raptor
Plextor 712A DVD/CD (SATA)
Here is my dilema: box powers up, POST stops at "Initializing Keyboard Controller". ( I know this because the little lights on the D-bracket tell me so.....:-) I have been on these forums as well as AMD's forums all day now, and have tried everything suggested, except swapping PS. But I think I have an adequate model.
One by one, I have disconnected any sources of possible problems. I have reset my bios too many times to count. I have isolated the MB outside of the case. I have re-seated everything numerous times. I changed Bios battery. I've swapped RAM, and it's positions. Even took it all off. I even bought another K8N from Ebay, and have the exact same results. At no time has the status lights displayed anything different, except for a quick change in color of light number 3 when I do a front-panel reset. Right now I have nothing but the processor on the board and I still have the same result; POST hanging at "Initializing keyboard controller". I have swapped keyboards unplugged the keyboard.
I am leaning toward the processor now. What am I missing? Should I just do an RMA and be done with it?
Suggestions encouraged......
James

Quote from: sincity337 on 04-August-05, 12:22:07
Bowen,
I've got an old Asus P2B that still runs like a champ, although slow by todays standards. You are right about it being rock solid, I have never had a problem with it, not one. As a matter of fact I still have it and I use it for my "linux box". Oops, a little off topic.
Anyway, it looks like MSI received the board today. I will start the stopwatch and see how long it takes to get a replacement board. I'll keep you guys posted.
James
Yeah those boards were the best I've seen. The Intel 865 chipsets are pretty good too. My previous 845 based mobo was nice as well. In the past, using VIA boards have been hit and miss with me. The K8T800/Pro and K8T900/Pro seem to be very stable though...still I would get an nForce 4 chipset over the newest VIA boards.
This is OT but I just received my shiny new BFG GeForce 7800 GTX OC card a few days ago and I was very surprised at it's performance. I was using a crappy Radeon X300 because I needed a temp card until I could buy either a 7800 GTX or the upcoming Radeon X900 XT. My last system I had a Radeon 9800 Pro and it ran flawlessly. I only had one problem with that card and it was driver related to only one game. The game was Call of Duty and that issue was resolved by going down to an older driver, but then ATi corrected the problem with a new driver release. Anyway as fast as the 7800 GTX is, I hated it! The reason is that despite it's awesome speed; the only way I can put it, is that it doesn't run games as smooth as Radeon's do. It was especially bad with Battlefield 2. This is ironic because BF2 is supposed to be optimized for nVidia cards.
It has a bad stuttering problem with BF2 and allot of people have this issue. Some have this problem with ATi cards but most are nVidia users. Even when I set the quality down to the same settings as my 9800P was at, it did the same thing. Other games like Counter-Strike: Source ran fine unless you had bots. Heh, even my slow X300 ran games more smoothly (not faster and at a much lower resolution and quality setting but still smoother) than the 7800 GTX. I sent the card back and I'm getting a full refund. I'm waiting on ATi to release their X900 XT and I'll buy that. What's strange is that prior to buying my 9800P two years ago, I had only used nVidia cards since the TnT2. Well times have changed I guess. Oh well, I guess I had to learn the hard way, but at least this way I know I'm getting the right card!

K8N Neo Platinum USB Keyboard Question

Similar Messages

Maybe you are looking for