K8N Neo Platinum will shutdown in about a minute

My K8N Neo Platinum will shutdown after about a minute of powering up. The front power LED will flash slowly and I am unable to power it backup without shutting off the main switch to the power supply and waiting awhile before I try again.
I can watch the PC health status within BIOS for a few minutes and all is well until I press any key. Once I hit a key the system shuts down.
The PC Health info...
System Temp    45C
CPU Temp     43C
CPU Fan Speed    3139-3154 RPM
Vcore       1.48-1.50V
+12.0V      12.03
+3.3V     3.29V
+5.0V    5.02-5.04V
Battery     3.22V
+5VSB       5.13-5.15V
NOTE: CPU temperatures start out at about 38C that seems pretty high to me. The room is not close to being 38C or 100 degrees Fahrenheit
In the BIOS I have...
- Loaded Fail Safe Defaults
- Disabled quick boot (so the memory will be tested)
- Removed logo displays (so I can see the memory being tested)
One memory module fails! But the other seems to test OK. With the bad module removed the system still shuts down.
My equipment...
ANTEC Sonata case with the built in 380W power supply.
K8N Neo Platinum
Athlon 64 3200+ processor
ATI All-in-Wonder 9600
Two Centon 512MB PC3200 memory modules
For testing I removed all IDE devices except for one good hard drive
NOTE: The system will boot up… but will shutdown as described above!
Do we have any ideas on how to isolate this further?
Thanks
JJ

Ok, had to reply to this one--had the exact same issue and this definitely is the weirdest experience I've ever had. (You can skip to the last paragraph for the short version).
I was having the exact same problem, turn on the power, go into the BIOS, all readouts look ok but then after about a minute it would shut off with a blinking power light. Would turn it off and back on, sometimes it would just get hung and I'd have to reset the BIOS with the jumper.
After about an hour of taking apart and putting the system back together over and over it occured to me--when does a power light flash? When the system is suspended. I also noticed that when I actually made it into the BIOS, the moment the system always shut down was when I hit a key on the keyboard (thought that was odd). So I unplugged my keyboard and let it sit at the POST error for not having a keyboard. I noticed when I did this it didn't shut itself down.
So then I wondered if the keyboard could possibly be sending some kind of signal the BIOS was interpreting as a "sleep" command. So off to CompUSA to get another keyboard. Mine is PS/2 but I thought maybe I'd try out a USB one to see if that would work out. I figured the PS/2 port was messed up and had an internal short or something.
Unplugged the PS/2 keyboard, plugged in a new USB keyboard and was able to make it into the BIOS, then I was able to actually boot Windows! (kept my existing Windows installation for the time being). I wasn't out of the woods yet though, Windows hadn't loaded the USB driver yet so I had no keyboard/mouse when I got to Windows (and I even had the BIOS support option for USB KB/Mouse turned on, but that didn't seem to make a difference). So, just for the heck of it, I unplugged the PS/2 to USB converter that came with my "USB" keyboard (thank goodness it was using an adapter) and plugged it into the PS/2 port again. This time the PC booted correctly and I've been using it with the new keyboard in the PS/2 port since with no problems. The old keyboard in the PS/2 slot still makes the system power off after a few seconds.
This has turned out to be one of the most bizarre scenarios I've ever been faced with. For reference, my original keyboard was a PS/2 Logitech Deluxe 104 KB, and I replaced it with a cheapo $15 Memorex (was just for testing but hey, it works now).
So anyway, this is absolutely crazy, but try using a USB keyboard or even a completely different keyboard if your system shuts "off" with the power light flashing after 5 - 30 sec after you turn it on.

Similar Messages

K8N Neo Platinum: Will future BIOS enhance GeForce performence boost?

I read that the Nforce3 250GB reference boards showed a performance boost when paired with a GeForce FX video card. The K8N Neo Platinum does not take advantage of this now, but will it ever in the future?

Don't know if you have tried this things but heres my list of things .
BIOS:
-First load bios optimized defaults , then ..
-Set the cpu vcore voltage up by + 0.025v (don't use auto)
-Increase the memory voltage vdimm to 2.7v (or the vendors max defined voltage)
-Disable fsb spread spectrum
-Disable dynamic overclocking
-Disable cool n quiet
-Change the multiplier from startup to 11
-Turn off auto on memory timings in cell menu/dram and set all values manually
and the max mem frequency to 200.
-Turn off AGP fatwrites
CASE:
USB connectors
-Disconnect case front usb from usb header on motherboard.
-Disconnect the d-bracket from usb header on motherboard.
-Change the red MSI ide cable if used.
-Check all stand offs/spacers under the motherboard .
-If using PS2 kb and mouse some board have mislabeled color code
making people connect mouse in kb and vice versa .
Correct is keyboard in the bottom mouse top.
STABILITY TEST:
Outside windows and windows drivers:
Download and test with memtest86 v 3.1
http://www.memtest.com
Inside windows:
Test stability with prime95 and/or hotcputester

MSI K8N Neo Platinum and DTR

Heya fellas,
I was wondering if anyone know whether or not the new MSI K8N Neo Platinum will have support for the AMD Athlon 3200+ DTR chip? I know some boards have had trouble with them and I'm hoping that this one, since its a new reviision, will conflict with it.
Thanks,
-Ish-

If that's the "Newcastle" version of the 3200+, it is supposed to work!

Question about S-ATA and MSI K8N Neo platinum

I'm thinking of buying a Plextor S-ATA DVD-burner but I'm not sure if my mainboard supports it? I have an K8N Neo Platinum board. Cause on the webstore that I'm going to buy it from it says "Check if your S-ATA controller has support for optical storage drives". Does anyone know if the K8N Neo board supports it?

I'd be very weary of using SATA optical drives unless you can find out FOR SURE whether or not it will work on this mobo - they can be finicky things at the best of times...

Question about K8N Neo Platinum and sound

I'm experiencing "gritty" sound when using the onboard sound of the MSI K8N Neo Platinum. Does anyone know why I'm getting this, and how to fix it? I'm using Klipsch Promedia speakers.

I couldn't stand the Realtek AC97 audio - it sounded thin and tinny.
I hated it.
I tried the nVidia drivers and the Readltek drivers, it didn't help - it sucked and there's now way to fix it.
Do your self a favour and get a Audigy 2 ZS (less than $100) and disable the $hitty AC97 audio - much better after doing that

K8N NEO Platinum 4 Red LED at Startup

I installed a new MSI K8N Neo Platinum mainboard in my computer in December 2005, and my computer has been a pain ever since. My problem is 85% of the time when I turn the power on it just won't boot up, I get 4 Red LED lights. If I shut it off and on half a dozen to 20 times. During one of those times it will bootup normal and work great. Shutdowns are normal.
My Family hates this and won't use it. This computer has been nicknamed the MSI Little Witch. I have had it down to barebones out of case with just graphic card, 1 memory stick, IDE harddrive, keyboard and mouse, it will do same thing. I've unplugged and replugged everything countless times. It still does it. I have tried Maxtor, Samsung, and Western Digital hard drives with fresh install of Windows XP Pro, it still does same thing. I have alternated memory sticks, same thing. It will warm reboot as long as I don't powerdown, but if I shut the power off it will not reboot until it cools down about 20 minutes. Then I can go through the same startup problems as I normally have. I have not done any overclocking.
Anyone have a fix to this fustrating problem?

I have the same problem with my K8N Neo Platinum. Except mine seems to occur after the motherboard has not had power after sometime. For example, it happened every time I moved my computer when I moved into and out of my dorm room. I don't know if its the same "cooling down" time you're talking about, but what usually fixes it for me (at least temporarily) is killing the power to the machine while it is on. Regular soft resets won't work for many tries, but when the computer is on with all 4 red LEDs i'll flip the power switch on the power supply. That usually makes it work fine. Also another thing that seemed to intermittently trigger it is changes to the BIOS. A CMOS reset would not fix that either. I would have to flip the power switch and kill the power. Then after starting it
up again it would be okay. I have also tried multiple combinations of different cpus, memory sticks, and video cards. I also made sure there were no shorts to ground anywhere.
Also after a year of solid operation (with the exception of this problem) I started to get Machine Check Exception BSODs in XP. I think this was because of a possible bad stick of RAM, because that seemed to cause lockups in the way beginning of the Windows setup (where it is loading files such as Windows Executive, etc). When I removed it and put another stick in, the windows installation would go fine. But, that did not fix the issue with this motherboard.
I've had so many problems with the multiple K8N Neo Platinums I have purchased. This is absolutely ridiculous I'm extremely POed at MSI for the widespread K8N series problems. I am usually very tolerant to companies when they have problems with products because I understand that problems and glitches can easily occur in mass production and design. It is virtually impossible to make a "perfect" product from the start. But the lack of response and concern from MSI about this is ridiculous. MSI did make an excellent motherboard here--if you can get a working one.

K8N neo Platinum Win XP SP2 random system crashes/Blue screen

I have recently built a new pc with the items as listed in my signature. Some of the compontents were new (RAM, HDD and VIdeo) and some were second hand (CPU, M/B, Keyboard and Mouse). I found that when I install WIN XP the system seems ok. But after I install any SP1 or SP2 which are required to run the USB2.0 my system crashes randomly and I get a windows blue screen and an auto restart. in the last week it sometimes lasts a day or so then it crashes. Other times it will crash within 5 minutes of start-up. I found a forum topic about a similar problem the other day but when I went looking for it again I couldn't find that topic. In that topic there were comments about PSU's and their ability to run the K8N Neo Platinum. In my specs are my PSU details. Can anyone advise if my PSU may be the problem or if there is any other problem.
I have made a WIN XP boot disk with SP1 and I have an SP2 disk I was given by a PC shop. If you are able to help or need further info to be able to help please let me know.
Regards
Kewlcop

Quote from: PStang on 18-March-05, 05:14:57
i had random shutdowns and blue screens until i uninstalled core center
LOL!
Yet another reason NOT to use Core Center!
This ought to have it's own sticky - Experiencing random reboots & blue screens? Uninstall Core Center first!

Wake on LAN/Keyboard wake for a K8N Neo Platinum - how do I use this?

I've got a K8N Neo Platinum motherboard that I am using in my home theater PC and I was hoping to enable either the wake on lan or keyboard wake functions so that they could be controlled via a remote control. For now disregard what the overall outcome I want to achieve is... what I want to know is if enabling the WOL and/or keyboard wake function will allow me to turn on the PC from a completely powered down state as opposed to just powering up from a sleep/hybernation mode. I have read people with other motherboards have been able to power up by using their keyboard, mouse or even WOL when the computer is totally shut down. I'm trying to avoid leaving the PC in a sleep/hybernation mode due to electricity usage. Does this motherboard have the ability to power up when the whole system is shut down?
Also, what key on the keyboard is used to wake up the computer? The manual and bios instructions say nothing about what key needs to be pressed to wake it up.

I know you can set various wake options in the bios. Check there!
You can wake up the computer by wriggling the mouse or pressing any key, if the options are enabled in the bios.
Hope this helps

K8N Neo Platinum not passing POST

Hello,
I have just bought an MSI K8N Neo Platinum OEM and it will not pass POST. I have gone through all the items in the Sticky section, but still it won't pass. I don't know what to do.
Here's the hardware I have hooked up:
MSI K8N Neo Platinum motherboard (has "MS-7030 VER:1" written on it)
Athlon 64 3000+ CPU, 512 K L2 Cache (ADA3000AEP4AP)
Kingston RAM (KVR400X64C3A/512)
Radeon 7200 graphics card (about 4 years old)
Seasonic S12 380 PSU
Thermalright XP-90 heatsink w/ 90mm Nexus fan
I have hooked up the 24-pin power cable to the 20-pin motherboard slot using the 24-to-20 pin adaptor supplied with the PSU.
The 12v 4-pin CPU power cable is also plugged in.
The graphics card is plugged into the AGP slot. There is no other power connection needed.
I have installed the CPU with a Thermalright XP90 heatsink and a Nexus 90 mm quiet fan.
I have hooked up the fan to the motherboard C_FAN1 slot.
I have installed the RAM (Kingston KVR400X64C3A/512) into DIMM slot 1.
I attached the case fans to the power supply and hooked up the case speaker.
I have also hooked up the front panel power and reset switches.
I bought the motherboard OEM, so it did not include a D-bracket. I have built a pseudo-D-bracket using two-colour LEDs and plugged it into the D-bracket slot.
With this work done, I plugged in the power supply. The power supply has an on/off switch on the back. As soon as I turn on the switch, the computer tries to boot up. All the fans start spinning (power supply, CPU cooler, case fans, video card fan). Nothing appears on the screen. The case speaker emits a long beep, waits about 5 seconds, then beeps again, and continues this pattern forever. The documentation says that this indicates a memory issue.
My homemade D-bracket shows the following: initially, all the LEDs are red. Then, the LED across JLED1 pins 7 & 8 turns green (with all other LEDs red). I assume that this corresponds to LED 1 being lit, although it really looks like it should be LED 4. Next, the LED across JLED1 pins 5 & 6 turns green (with all other LEDs red). Once again, I assume this corresponds to LED 2 being lit, although it looks like it should be LED 3. I looked this up and the documentation indicates a memory error. To solve the problem, I have tried the following things:
1. Hitting reset. Same boot sequence.
2. Clearing the CMOS using the JBAT1 jumper. I left the jumper at "clear data" for about 10 minutes, then switched it back. Same boot sequence as before.
3. Clearing the CMOS by removing the battery. I left the battery out for 3 minutes, then 30 minutes, then 8 hours. Same boot sequence.
4. Removing the motherboard from the case. I placed the motherboard on the anti-static bag it came in. Repeated steps 1, 2 and 3. Nothing.
5. Move the RAM to DIMM slot 2 or 3. Tried steps 1, 2 and 3 again. The boot-up sequence was the same.
6. Different RAM. I have also tried using OCZ 400 MHz 512MB unbuffered DDR memory (OCZ400512V3). Performed steps 1-5 with identical results.
7. No RAM. Same boot problem.
8. No video card. Ditto.
9. No RAM or video card. Exactly the same as before.
As far as I can tell, all components are supported. The only item I am very unsure of is the graphics card. I do not have the exact specifications on it. When it is in my other computer, the driver details identify it only as a "Radeon 7200". However, it does have the "golden finger" shown at www.msicomputer.com/support/sup_tshoot.asp#1_3. Even if the video card is not compatible, it seems like the beep codes and D-bracket codes both indicate memory issues.
The only thing that I have noticed that is weird (other than the fact that the computer won't pass POST) is that when I turn on the power supply, the computer immediately boots up. I don't know whether or not this is normal.
Lastly, I do not know the current BIOS version. Is it possible that the BIOS is an early version that does not support my memory/CPU/video card? I bought the mobo OEM, so I do not know what BIOS it has loaded. Is there some way I can figure this out without passing POST? This is driving me absolutely insane.
Thank you for your help,
Kyle Renwick

Make sure the fan you are using for the xp90 is supporting RPM readouts .
Then try another AGP gfx card , sometimes you can have a no post due to that the graphics adapter wont start .
Take the system bare bone ( mobo + cpu + ram + gfx )
Have any award beep codes ? , note them down and decode them against
http://bioscentral.com/beepcodes/awardbeep.htm
Still stuck !
Remove AGP + ram too .
The mobo shall beep (endless beeping )
Insert the ram , the mobo shall beep - missing gfx .
Got this far and you know cpu + memory initialize but have problems with gfx or other devices
later in the post/init process .
Do not have any usb devices connected to internal or external connectors ,
note that the USBOC pin un JUSB1/JUSB2 is NOT to be connected .
Also try altering between ps2 and usb keyboard as this also has caused non post situation for people .

K8n Neo Platinum non-booting SATA RAID setup question

I've spent several hours searching an reading trying to find out how to setup a non-bootable SATA RAID. All I can seem to find are posts about bootable installs using F6 and the drivers on a floppy.
I have setup the disks in the bios an defined the array an everything checks out. But when I boot back to WindowsXP it only sees 2 drives that it cannot find drivers for even if I point it to the correct Nvidia directory. I attempted to just reinstall the drivers but that caused a Bluescreen from a corrupt driver file that I then had to go into the repair console to copy from a floppy.
The manual an a couple of posts here say that I should go into Admin Tools-> Disk Management an it will then popup a wizard. But I'm not getting that far.
I currently have the disks on SATA 1 and 2 but will move them tonite because I've read its better for them to be on 3 and 4.
This is on a K8N Neo Platinum 7030 on Windows XP SP2. If anyone could help or just point me to where I can find help it would be greatly appreciated.

When the raid controller is enabled in bios and you start windows you can install the nvidia raid driver
from within windows .
Use the add hardware wizard from control panel .
Start the add-hw wizard .
Yes i have connected the hw - next .
Add a new hw device (bottom of the list ) -next .
Install the hw that i select manually from a list - next .
Select scsi/raid controller - next .
Choose have disk .
Then browse for the location of the nvraid.inf file

K8N Neo Platinum issue, computer does not boot..

Hello,
I’m going to try to be as thorough as possible here… :D
Recently I reinstalled Windows Xp (32-bit version) on my computer to speed things up again like it used to be. I did an updated on the BIOS while I was at it as well, through the Live Update tool downloaded from the msi.com.tw website. The install went well, no errors. The next day while playing WoW the computer began acting weird and computer froze during gameplay. After that the computer had artefacts, strange disturbance on the screen making it impossible to see anything on the screen. So I thought that maybe since the screen looked all messed up it was definitely the graphics card that was about to die and so I sent the gfx to the retailer and they checked it thoroughly for errors without finding any, while they were at it they also checked my RAM and they also came out clean.
A few days ago when my Gfx and RAM came back I inserted them back onto the mobo and when turning on the powerswitch nothing happened… I therefore tried to solve the problem myself and began reinserting all the computer parts piece after piece and well the computer started at least with the fans going and all but after a few seconds it shuts down again.
When I plug in the power cable the PSU makes a clicking sound, don’t know if that’s normal but haven’t noticed it before.
To maybe help you guys when helping me I installed the d-bracket (the usb thingy with 4 led’s ^^) which shows 4 red lights when starting the computer and lasts until the computer shuts down. According to the d-bracket FAQ it means: “- The D-LED will hang here if the processor is damaged or not installed properly or you have a weak Power Supply Unit.”
Well I reinstalled the cpu, put on new thermal grease so I don’t think that is the problem and the computer has been working fine for more than one year until now... How do I know if it’s the PSU or if the cpu is damaged? Could the motherboard been damaged after Live update’s flash? And what could have caused the artefacts on my screen the other day? Errors with the newest nVidia gfx drivers? I’m very confused :S
What should I do?
Thank you for your help!
Computer specs:
Amd 64 3400+ with Zalman cpu fan(can’t remember which one, one with only Cu heatsink + fanmate)
1 GB (2x512MB) Corsair 3200
1x 74GB Western Digital Raptor 10k RPM S-ATA + 1x 200GB P-ATA Maxtor
Gainward nVidia 6800GT Golden Sample 256 MB
MSI K8N Neo Platinum Nforce3 250GB
Antec True 380SP, 380W (came with my enclosure Antec Sonata I, www.antec.com)

Hi again..
I've now received a new PSU from Antecs RMA department. A TruePower 2.0 380W. My computer still doesn't work. 4 Red LED's when trying to boot it up. But I have noticed one thing since last time I wrote here. Remember what I was saying that I upgraded my BIOS through LiveUpdate? When I later checked my motherboard I noticed the CMOS pins around JBAT1(I think) was incorrectly placed. Instead of having them on either 1,2(to keep settings) or 1,3(to clear CMOS) they were placed right next to the JBAT1 pins, on something that wasn't named or explained in my manual. Maybe that is the reason my computer is acting strange? I mean the BIOS could maybe not have properly been saved or something. :/
I'm too inexperienced to know if that had anything to do with my recent computer isssues, but maybe you guys know. Would that screwup by me be covered by my warranty?
If that pins-placed-wrong-on-the-mobo problem doesn't have anything to do with my problem that leaves me with the 4 LEDs from the D-bracket showing a broken CPU or PSU(it's brand new, shouldn't be any problem with it!). So a damaged CPU it is.
Anyone of you got an idea? Been away from my computer for too long. This is getting annoying.
Thanks.
/Christopher

MSI K8N Neo Platinum & Crucial Ballistix 512MB RAM Problem

I have had MSI K8N Neo Platinum and 1x Crucial Ballistix 512MB RAM for 11 months.
I have had 1x Crucial Ballistix 512MB RAM for 2.5 months, for a total of two.
I have had MSI GeForce 6600GT (NX6600GT-VTD) 128MB AGP for 1 month.
For about 1.5 to 2 weeks, I have been seeing random crashes while playing PC games.
I started a thread on the Hard OCP forums a few days ago. I did not know MSI had forums =)
Rather than re-typing, I may as well just post the link:
http://www.hardforum.com/showthread.php?t=934956
My issue is also similar to this one:
https://forum-en.msi.com/index.php?topic=83799.0
Thanks for the help.

ALL RIGHT, after almost FOUR months my issue is FINALLY resolved.
It is amazing how much time passes when you are hesitant to buy parts unless you are 95% sure it will fix the problem.
OK, here is an update as to what I remember.
I went to BIOS 1.4 and tried many different physical and BIOS RAM configurations (Different seating, different number of DIMMs, different RAM timings, voltages, etc).
I concluded that I could not make my PC 100% stable, but I could get it darn close. With certain settings, such as DDR400, 2-2-2-6, 1T, 2.80V, Aggressive Timing enabled, Memtest failed test #5 every time (this is spec for my RAM). With other settings, such as DDR333, 2.5-3-3-7, 2T, Auto V, Aggressive Timing enabled, Memtest failed test #5 maybe once out of 5000.
I also concluded that the RAM voltage and Aggressive Timing setting was having a big impact. Some settings would not work (failed Memtest) with RAM at 2.80V but would work with RAM at Auto V. Some settings would not work (failed Memtest) with Aggressive Timing enabled but would work with it disabled.
Finally, I started to occasionally get R,G,R,G (Processor Initialization) on the D-Bracket upon cold-start & warm-start, which suggests a PSU issue:
https://forum-en.msi.com/index.php?topic=76972.msg542545#msg542545
That pushed me over the top, and I decided to buy a new PSU (TG-480-U22) and a new SATA HDD (WD2500KS) just because.
Problem solved. Thanks for all the help.
I will continue to buy MSI in the future just because of these forums…and a good product of course!

MSI K8N Neo Platinum - CPU Cooler?

Hi there, this is my first post to the forum and hope that someone can help
Bascially I've just purchased a MSI K8N Neo Platinum mobo to use with an AMD 64 2800.
I'm wondering if I should use the stock CPU cooler or look to purchasing a cooler such as a Zalman? I want to keep the computer as quiet as possible.
I've recently read that it would be better to use the Cool and Quiet option with the stock CPU cooler instead?

Chris,
If you don't mind a used one, there are probably about a hundred thousand available ones from people in these forums who has upgraded their heatsinks, and that's about everyone
The problem is, we dont want to give them up. We bought the retail package with fan not because of the free heatsink/fan, but because of the 3 year warranty that you only get with said combo. To invoke the warranty, we'd have to return everything, including the heatsink/fan, so we hang on to it and let it collect dust.
So, for an aftermarket fan. If you don't plan to overclock, ever, the thermaltake silent boost K8 will do, although it is nowhere NEAR the 21dB that tt claims. They are known for shall we say, exaggerated claims. But it's certainly quieter than the stock HSF, and it's available everywhere.
Note that the "silent boost k8" is different from the "silent boost". The latter is for socket 462 I think.

Msi k8n neo platinum ps2 keyboard problem

Hi. I'm having issues with my msi k8n neo platinum motherboard. I've read about 50 posts on these forums regarding the supposed ps2 keyboard issues with recent msi boards. However none of them seems to address my current situation.
Like many others, when I power up my system the cpu fan spins for like 3 seconds then everything comes to a halt.
I tried many things to get my system to boot and the only thing that works is plugging my ps2 keyboard into the ps2 mouse port and moving the ps2 mouse into a usb port with an adapter.
It seems there's no hope for fixing the problem other than RMA'ing, but I thought I would add to the pile of complaints stacking up against the MSI boards.

if u had read the threads a little more u might have found a solution that seems to have worked 4 many - a usb keyboard usb Keyboard if u go this route dont forget to enable usb kb in bios
Edit: This Thread Summarises the situation PS2 keyboard/mouse causes random shutdowns or doesnt work

MSI K8N NEO PLATINUM (RAM/HD problem/mobo problem?) [SOLVED]

my setup:
windows xp pro sp2
amd athlon 64 3200+
msi k8n neo plat - 7030 - bios 2.1
x800 xt vid
sound blaster audigy 2
kingston valueram pc3200 2x512 cas 3-3-3-8
ps = antec 430 watt truepower power supply (20 A on 12V)
I dont know if you guys remember my but i created a topic on here a while back about how my keyboard and mouse suddenly stopped working, well that turned out to be that the msi k8n neo platinum just went bad. So i RMA'd it and recently got the replacement board (with latest bios already installed). It worked completely fine for about a day. Well that same day i got it back, i installed a Logitech G7 USB wireless mouse. after i installed it, i began getting numerous windows stop blue screen errrors, even after i removed the mouse from control panel. So i figured i should format because to rule out everything and start fresh. So i did a FULL format and attempted the reinstall windows again. AFTER the format and BEFORE windows attempted the continue installation, i got the same stop error. I figured now this was a hardware problem. So first i tested RAM. I got the latest version of memtest86 and let it run for 4 hours (11 passes) with NO errors at all. Secondly, i got a western digital hard drive diagnostic program to test for failing hard drive and again no problems with that. I still suspected ram so i tried to boot with only 1 stick installed (in first slot), however the PC didnt boot at all (cleared cmos too). So i moved it to the second slot and cleared cmos again and this time it posted but it just hangs at a cursor and does nothing, same thing happened with third slot. I tried this same procedure clearning cmos each time with the second ram stick and got the SAME results. Shouldnt the motherboard boot with only 1 ram stick installed? Did MSI RMA me another bad board? Any help would be appreciated. thanks.

Quote from: russellmrgn on 28-March-06, 10:54:39
Sap147
Can you give us what the D-Bracket was showing ie
R R
G R
As an example this means "Initializing Keyboard Controller"
You will find this information in the manual page 2-23. (On mine) under Hardware Setup
Also can you please do all your tests with the ps2 keyboard and mouse and for now leave your Logitech G7 USB wireless mouse to one side.
Russell
for two sticks of ram = RR
GG
for one stick of ram = GR
GG
as for the g7, it hasnt been plugged in at all, i took it out long ago.. as for the ram, the timing was set to 2T, no overclocking, i will try 2.7 v and let you know, but for the record, it has been running at normal voltage settings for about a year perfectly fine.

K8N Neo Platinum will shutdown in about a minute

Similar Messages

Maybe you are looking for