K8N Neo2 939 and BFG 6800 Ultra not getting along

Everything runs ok until I install the drivers for the Geforce 6800 and then everthing goes to hell. So I was having IRQ problems because MSI is not smart enough to to put some kind of VGA AGP IRQ assignment in the BIOS. I disable onboard audio, also the Serial and Parellal ports (who uses these things anymore?) to free up Irqs. It works and no more Blue Screen, but I still have artifacts, or something like that, when I boot into windows that looks like static lines in the screen.
Here is the question I have I am getting all these conflicts, memory and the such, between the motherboard and the 6800, I think this is the problem, does anybody know how to clear this up? Or if the problem might be something else?
THXs you very much before hand.

It was over on the EVGA forums when I was trouble shooting my card
What drivers are you running?
edit:
http://www.evga.com/community/messageboard/topic.asp?TOPIC_ID=3976&FORUM_ID=23&CAT_ID=1&Topic_Title=Having+problems+with+your+card%3F++READ+HERE+FIRST%21&Forum_Title=GeForce+6+Family+Forum

Similar Messages

  • Powerbook (digital audio) and 1/8" jack NOT getting along

    ok see if you can help me troubleshoot this.
    i bought two of these cables:
    <http://www.cablesforless.com/index.asp?PageAction=VIEWPROD&ProdID=2779>
    "Our Custom Made 3.5mm Male to 2-Male 1/4 inch phono plugs audio cables are perfect for connecting your speakers and microphones. These cables feature Belden's 1800B digital XLR cable and Steren® precision machined connectors. To ensure maximum signal integrity and protection from RF and electromagnetic interference the cable also features a Beldfoil® shield and fully shielded connectors. Professional termination using high grade solder ensures optimal signal transmission. Designed for optimal sound quality, Belden's performance speaks for itself. Compare Belden's specifications (below) with those of other digital XLR cables and see for yourself how Belden cable is unmatched. Belden Brilliance® teamed with Steren Connectors brings audio to life!"
    sounds good, right? they both exhibit the following symptoms.
    i'm using it in the headphone jack of my powerbook g4 15" and going out to a little mixer so i can hear system audio, itunes, etc. through my system. this longer cable is replacing a monster cable of the same kind (but shorter).
    i'm getting absolutely HORRIBLE buzz when i plug it into the headphone port. if i jiggle it a bit i can get it to behave but only if it sits just right.
    on a crt imac and an older titanium powerbook G4 the issue is much better. i still hear a line hum. i wouldn't want to record like this, but it's not a nightmare.
    on an ipod plugged into the power adapter it works beautifully. however, i CAN get it to buzz horribly if i jiggle the plug as i insert/remove it.
    eyeballing it with the monster cable tip, it looks exactly the same.
    so on one hand, the monster cable works great in all uses.
    the cablesforless cable works terribly on the powerbook but nowhere else.
    now here's a clue: the powerbook G4 has combination analog/digital input and analog/digital output jacks. i haven't been able to repeat it reliably, but the cablesforless cable seems to be able to trigger the digital interface part, as evidenced by a red light shooting out of the port.
    unplugging the powerbook totally removes the buzz.
    i get the buzz when this cable is in EITHER the input or output jack.
    tried a different power supply in a different jack in the same room... same results both ports (slightly different tone to the buzz)
    if i remove the little mixer and plug the 1/4" cable ends into two inputs on a practice amp, i get the same issue.
    finally, i got another digital audio powerbook g4 15" and the connection seems to be slightly more reliable, but still problematic.
    PowerBook G4 Aluminum   Mac OS X (10.4.5)  

    For starters, EPUB is a profile of XHTML, not HTML5. Further, audio and video support are part of the recently-approved EPUB3, which the release notes for ADE 1.8 explicitly say is not yet fully supported. Specifically, <epub:trigger> will allow you to use audio and video: http://idpf.org/epub/30/spec/epub30-contentdocs.html#sec-xhtml-epub-trigger
    Do these EPUB files that you're not seeing in ADE pass validation? http://validator.idpf.org/
    Basically, it sounds like you're trying to do things that ADE isn't supposed to support yet, and in a way it is unlikely to ever support (since ADE is known to be pretty conformant to the EPUB standards, it's very likely it will support the EPUB3 version of doing things rather than the hackery I've seen for Apple's reader).

  • BFG 6800 Ultra causes K8N Neo2 Platinum to not POST - Problem finally resolved!

    I'm able to run with an ATI Radeon 9700 Pro and a PNY 6800 GT with no problems, but as soon as I plug in my BFG 6800 Ultra I can't get it to POST. The D-Bracket indicates it's doing "Processor Initialization". I don't see any output at all even though steps prior to "Processor Initialization" should be writing a few things to the screen. I should be getting plenty of power as I've got a good PSU and have two of the lines going to the BFG and nothing else. I've tried using several different combinations of lines as well so that doesn't appear to be the problem. I've already changed all the usual suspects in BIOS that might affect the AGP. I've also put the BFG in a crappy Dell system with a crappy PSU and it handled it just fine.
    Anyone got any suggestions? I can't seem to find anyone else reporting this problem so apparently I'm the lucky one. Pleeeeeaaaaase! Someone help me fix my problem!

    Keep in mind that not all Motherboards regulate their VCore and VDimm almost entirely from the 12v rail. However while it does task that rail it does provide a way for the manufacturer to provide more stable voltages and power. So different boards will react slightly different based even on the same exact set of parts. With so many parts needing 12v these days you have to make sure the PSU is up to supplying enough for everything.
    The second thing is how differently each MB sets up in Bios. This can have quite an impact on RAM timings. Loosen up the timings a tad and maybe things will also go a tad easier. However if you can't get any poost then you may have to try an older stick of something like PC2100 or somesuch so that you can enter Bios and set appropriate timings for the RAM you want to use.
    Third you can read the various stickies like Basec Building tips to help you get things properly setup.

  • New K8N NEO2 PLAT. and SC-939 3200+ help needed...

    Hello,
    I have just upgraded my system with K8N Neo2 Plat. and sc-939 3200+ A64 Cpu.
    There are several issues I need to resolve which are:
    1- Although I change from BIOS the settings for AGP to 4x8x and enable fast writes, I still cant see them turned on from the Catalyst Control Center. Everything is greyed out what can I do? They all used to be on and agp was 8x with my K7N2 Delta board....
    2- Although I installed the original drivers from the MSI CD, I couldn't get one of the network prts to install. Realtek installed OK. But other one is defined by the device manager as standart network adapter. What can I do?
    3- I am brand new to A64 system so I do not know what setting to use from BIOS can you help me out, for instance there are values for HT such as x3 x4 x5  mine is set to x5? what is this? should  I enable cool and quiet, I am not intended to do overclocking. Can you give me some tips for best performance?
    My best regards.

    Make sure your bios is up to date: version 1.5. Look at the sticky threads and use the information to enable hidden bios features. Disable ATI/NV speedup in the bios. Uninstall your drivers and reinstall. If the information is still greyed out, download the free version of Sandra here: http://downloads.guru3d.com/ and check the module under video system information. This will tell you if fast writes are enabled and your AGP setting. Leave the HT(hyper-transport) set to 5X unless you plan on oc'ing, if you do oc then may find you'll need to reduce it to 4X or 3X. Try downloading the latest driver for your network from the MSI website. Right click the device in device manager and select update, select specific location then "don't look...I'll choose", direct it to the file where you've unpacked the correct driver and then update.

  • Neo 2 desert combat shuttering (sliding skipping etc)problem with bfg 6800 ultra

    hey guys i just built a new pc after i got everything installed and updated to service pack 2 i installed desert combat only to have shuttering problems especailly turning fast in chopper or plane its kinda like lag or dropping frames but according to fraps its not drop frames just really choppy game play i know its not the card because i stuck it back in barton 3000 board worked fine. put my old msi 5950 ultra in same problem
    fixes tried with no sucess
    reinstall windows
    turned off nv
    turned off fast writes
    tried my old set of 512 corsair plantinums =i gig dual chan
    install nforce driver from nvidia
    tried serveral nvidia graphic card drivers even the bet 71.21
    turned off spread spectrum
    pulled hair out
    tried old video card which is 5950 ultra both cards work fine with old mobo
    basically im out of ideas
    please help
    system specs
    90mn winchester core 3500 with xp 90 thermalright heatsink
    audigy zs 2
    corsair 3200LLPro with leds i gig in dual chan mode
    two 74 gig raptors in raid o
    OCZ 520 watt modstream powersupply
    bfg 6800 ultra overclocked from factory 425/1100
    xp pro fully updated sp 2
    please please please help been working on this for two days without any luck maybe ill just rma the board and get an asus or gigabite board

    First off have you been using Driver Cleaner to get rid of all the old bits of drivers? if not go get it read the instructions and use it.  Re-start the driver process again.  The latest ones on the Nvidia site are probably a safe bet at the moment.  So clean your PC with that prog and install new drivers.
    Then do as you say you have done and ensure 'FastWrites' are turned off.  This is most important.  Get 'Riva Tuner' and this will comfirm you have them turned off.  Also get the 'Coolbits' registry tweak.  Run this and it will add overclocking capability to your display properties.  You can adjust both 2D and 3D speeds.  Now what you must ensure is that they are both set at the same speed!  sometimes the 2D comes set lower than the 3D this can cause symptoms like you are having.  Set the 2D to the same speed as the 3D.
    I have an XFX6800 Ultra  in my K8N Neo2 Plat and it works superbly so fingers crossed doing the above will sort it as they are the main probs with the 6800Ultra cards.

  • K8N Neo2-F and Floppy

    Hi All,
    Just install a new mobo (K8N Neo2-F) and all is good, but I want to update the bios to fix the USB 2.0 problems. I just ordered a new Sony floppy drive and installed it. When I turn on the computer the green light stays on the floppy and it never gets detected (WinXP x64). I checked the power and it's in right and the cable is installed correctly. I did notice that the floppy connector on the mobo is missing pins. Is this by design on this board? Also, I tried booting from a usb floppy to no avail. Is there something I'm missing? Thanks for your help.
    Matt

    floppy cable always missing some pins but make sure that pin 1 (red) is on the correct side (see instructions that came with the floppy).  You may need to enable FDC (floppy drive controller) in bios.  You may need to enable USB boot in bios also if that is what you want to use, but this could create other issues I think.  Good luck.   

  • MOVED: K8N Neo2 - WinXP and Raid driver problem

    This topic has been moved to AMD64 nVidia Based board.
    K8N Neo2 - WinXP and Raid driver problem

    Quote from: SillySider03 on 18-June-05, 22:18:50
    Try This.
    Yes it worked... I did it a bunch of mins ago, ty a lot anyway 

  • I have IMac 10.7.5 Lion I use I forgot the password and I did a few fixes from the we sites, which did not work and now I can not get the computer to reboot the gray screen comes on and if a shift c I get a load bar and it goes half way and help

    I have IMac 10.7.5 Lion I use I forgot the password and I did a few fixes from web sites, which did not work and now I can not get the computer to reboot the gray screen comes on with the apple and if a shift+c, I get a load bar and it goes half way and stops, I can get into the black screen area with the hard drive info
    I did the following:   mount -uw /    rm/var/db/.AppleSetupDone    shutdown/uses/us  reboot Ok I know I should not have, but now I need help to reboot and hopefully not lose everything on the desk top, Linda Markle

    You did the wrong things. In the future it's a good idea to remember not to do something when you don't know what you are doing and what happens when you do it.
    Forgot Your Account Password
    For Lion, Mountain Lion, or Mavericks
        Boot to the Recovery HD:
    Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
         When the menubar appears select Terminal from the Utilities menu.
         Enter resetpassword at the prompt and press RETURN. Follow
         instructions in the dialog window that will appear.
         Or see:
           Reset a Mac OS X 10.7 Lion Password
           OS X Mountain Lion- Reset a login password,
           OS X Mavericks- Solve password problems,
           OS X Lion- Apple ID can be used to reset your user account password.

  • I just upgraded my iMac to OS 10.8.5 from 10.6.8 and now I can not get the calendars on my Mac and my iPhone 4s (running iOS 8.3) to sync

    I just upgraded my iMac to OS 10.8.5 from 10.6.8 and now I can not get the calendars on my Mac and my iPhone 4s (running iOS 8.3) to sync.  I already tried replacing the calendars on the phone with those on my computer but nothing happened.

    Set up iCloud
    Set up iCloud (2)

  • I recently updated my iphone software to 6.0.1 and my ringtones did not get added back to the phone.  I have connected my phone to my pc to sync but when I click to sync, it does nothing.  How can I get my ringtones back on my phone?

    I recently updated my iphone software to 6.0.1 and my ringtones did not get restored.  The ringtones are lised in my library but I can't get them added to my phone. When I click on the button to sync my phone, it does nothing.

    Welcome to the Apple Community.
    Try unchecking the tones and syncing, then re-checking them and syncing again.

  • I have a Canon MX882 and more often than note get an error message saying the printer is not connected. I check the printer and the get the message that the access point is accessed. I have reloaded the software and it worked for awhile. Any ideas?

    I have a Canon MX882 printer and more often than note get an error message that says "Printer not Connected." When I check the printer itself, I get confirmation that the access point is connected. I tried reloading the software and that seemed to have solved the problem for awhile but I'm experiencing the same problem. Any ideas what is causing this?

    Did you delete all receipts with iDVD in the file name  with either a .PKG or .BOM extension that reside in the HD/Library/Receipts folder and from the /var/db/receipts/  folder before installing the new copy?  If not then do so and delete the new application also.
    Click to view full size
    Then install iPhoto from the disk it came on originally and apply all necessary updaters: Apple - Support - Downloads
    OT

  • I don't remember setting a pascode in the restrictions and now I can not get my icloud on, can you help me?

    I don't remember setting a pascode in the restrictions and now I can not get my icloud on, can you help me?

    If you don't remember the restrictions passcode, your only option is to force the phone into recovery mode and restore it as a new device.
    Do NOT restore your backup. The restrictions settings are part of the backup.

  • HT1338 My kid down loaded mackeeper and now I can not get rid of it.  I have tried all techniques suggesting on several sites and still can not empty the trash can.  keep getting error code -8003.  Help.

    My kid down loaded mackeeper and now I can not get rid of it.  I have tried all techniques suggesting on several sites and still can not empty the trash can.  keep getting error code -8003.  Help.

    http://reviews.cnet.com/8301-13727_7-20020873-263.html
    This should help you empty what's currently in the trash, but is no guarantee you got everything related to MacKiller off the drive. See Ogelthorpe's link.

  • HT1937 I am trying to charge my Iphone 4s and suddenly i can not get it to charge, what might be the problem?Brian

    Hey guys,
    I am trying to charge my Iphone 4s and suddenly i can not get it to charge, what might be the problem?Brian

    Are you using a original USB cable? if not, than it could be the cable. If you are charging the iPhone with your computer, sometimes the USB port where you plugged in the cable stops working. plug it into a different USB port. 

  • I had to change my password for one of my Email addresses and now I can not get mail into Firefox.

    I had to change my password for one of my Email accounts ([email protected]) and now I can not get the mail to go into Mozilla Firefox and I don't know how to change the password in Mozilla to get the mail into it.
    I looked at how to change my password but the options you told me to use were not available. I clicked on tools then options but there was no sync tab or manage accounts either.

    The login.salesforce.com website is using autocomplete=off to prevent Firefox from saving the name and password.
    You can remove autocomplete=off with a bookmarklet to make Firefox save the name and password.
    *http://kb.mozillazine.org/User_name_and_password_not_remembered

Maybe you are looking for