K8N Neo2 + NVRAID + Promise Raid Controller = not working right

I'm trying to get my Promise Raid card working with nvraid enabled and I've finally given up. It works fine with NVRAID disabled though. I have 2xSata on Raid 0 and 2xIDE on raid 0+1. i also have two other IDE's on non-raid and two atapi cdrom drives. In order for me to use all of my storage devices, i need the promise controller to boot. The Prommise RAID controller's BIOS will not boot with nvraid enabled. WindowsXP detects the drives, but if i try to mount them via PAM (Promise Arry Management), it says one of the drives is corrupt/not working. but if i have both the ide raid hd's on the nvraid w/ sata raid, then it works fine. I just won't be able to use my cdrom drives. if anyone has a fix for this, please let me know. and sorry for the long descriptions. thanks.

Why don't you go into BIOS and alter the IRQ manually for that PCI card, because probably that card is using the same IRQ as the nVidia one.
Be well....

Similar Messages

Intel(R) ESB2 SATA RAID Controller not working out of the box

Dear all,
I'm using, for my tests, an old server with a supermicro X7DBN Server motherboard.
This motherboard comes with an embedded Intel(R) ESB2 SATA RAID Controller.
When I try a native installation from the technical preview DVD it sees the RAID1 volume that has been created (2 disk mirror) but when I select it to proceed with the installation there is an unknown error stating that it's impossible to write to this disk.
The same installation works perfectly with 2012R2 and the out of the box driver provided bin the install media.
An update from the previously installed 2012R2 to the Windows Server Technical Preview also works without problem.
It would make sens for MS to revert to the driver version embedded in 2012R2 for Intel(R) ESB2 SATA RAID Controller which is:
Name : Intel(R) ESB2 SATA RAID Controller
Date : 10.08.2010
Version : 8.6.2.1025
inf section : iaStor_Inst_RAID
Device ID : PCI\VEN_8086&DEV_2682&CC_0104

Hi,
Thank you for the information. As you said from the behavior it seems that the build-in drivers of Windows Server Technical Preview will not work with the specific motherboard hence the RAID1 cannot work well.
I'll log the issue down.
If you have any feedback on our support, please send to [email protected]

K8N Neo2-F and 4x256 TCCD not working at 200MHz...

I don't understand why I can't run my memory at 200MHz... Just installed 4 sticks of 256MB of G.Skill using CPC = 2T but then my graphic applications crash after a minute or two. Move down to 166MHz and it is now stable. Does anyone know how to fix that? BIOS updated to 1B0 and I have a 3500+ Venice

Quote from: RafaDel on 20-November-05, 07:24:02
Syar - I'm more familiar with DFI NF4 boards which does vcore increases right. I replaced my PSU with a good 420W but get the same results... I also realized that using % over VID did work, a little to late, as I could save some bucks with the new PSU. So far 4x256 TCCD on this board just at 166MHz. Tried 200MHz even with 3-4-4-8 and no go...
Jaybee - I took decision myself, not a problem.
If you guys have any other ideas, please

Howto use onboard Promise Raid Controller pdc20265 on 694D PRO AR Ver1

Currently I'm running Win2k on my MSI 694D Pro AR Ver 1.0 board with Bios version W6321VMS.310 and the included Fasttrack-Family Win2k Raid-Controller driver for my Promise Raid Controller pdc20265 with lite bios.
Due to software updates I'm now absolutely required to switch to Windows XP Prof. However this is the cause for my inquiry:
I downloaded and installed the latest available Bios version W6321VMS.370 from MSI site.
On installation of XP I tried to include the pdc20265 Fasttrack raid driver from MSI site to get access to my HD's. However WinXP couldn't find any HD's. Remark: XP with SP1 and VIA 4in1443v.exe installed.
So I repeated this procedure with the original drivers Fasttrack family and pdc202065 which were attached on floppy. Unfortunately no success as well.
Then I have put the HD on the Ultra66 channel and installed XP first without raid and ultra 100 support.
Later I re-enabled the on-board promise device in bios and unfortunately WinXP didn't recoginze the device by itself. So I provided the latest pdc20265 driver from MSI site. XP complained that the driver is not digitally signed. After reboot the promise device reported an error under WinXP.
I repeated this procedure with the original drivers Fasttrack family and pdc202065 which were attached on floppy. Unfortunately no success as well.
Why MSI-Site says this pdc20265 driver supports WinXP if there are only the Win2k and WinME,98... drivers included?
Currently I can't use the promise device at all under WinXP. This means even I don't have an Ultra 100 controler available.
Has anyone an idea how to install HD's on WinXP with the corresponding promise raid drivers for my pdc20265 onboard chipset?
I'd really appreciate your help!

Some of the suggestions I don't understand quite well. Please could you explain further:
> remove the other two drives leaving the raid pair
> and cd only
>
> put raid 2nd in boot order
What do you mean with that?
> reboot press the key you need to get in to raid bios
> create the array and make it bootable
array is already created (Note: there is important data on it, can't recreate it! Only Segate 80GB is free and empty)
I don't want to boot from raid.
>
> now boot to cd to install,right at beginning it will say
> press f6 to install mass storage drive you need the
> driver on floppy to install it
I already tried the XP-Install routine to specify additional mass storage drivers. (Note: 1 single 80GB Drive was attached) Which are the suitable ones? As mentioned I tried the following:
1. Attached floppy 'Fasttrack family drivers'
Result: Message: Driver is for Win2k only. Not a single Harddrive shows for installing XP.
2. Attached Floppy (Promise Ultra 100 lite, 256 only)
Result: Driver is for Win2k only. Installation procedure hangs.
3. Driver from MSI-Site for pdc20265. Same as 2.
4. Extracting via4in1 drivers and putting WinXPIDE drivers on floppy:
Result: Installation routine doesn't recoginze drivers on floppy.
> rest should be the same as normal
>
> this should be similar as well
>
> http://www.amdforums.com/showindex.php?s=&threadid=146384
Which is the right driver for WinXP to specify for mass storage device at WinXP installation?

MOVED: K8N Neo2 - WinXP and Raid driver problem

This topic has been moved to AMD64 nVidia Based board.
K8N Neo2 - WinXP and Raid driver problem

Quote from: SillySider03 on 18-June-05, 22:18:50
Try This.
Yes it worked... I did it a bunch of mins ago, ty a lot anyway

PCI Simple Communications Controller not working

PCI Simple Communications Controller not working on hp pavilliong6-1003tx

Hi
Download, save & install --
Windows 7:
http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-94322-2&cc=in&dlc=en&lc=en&...
Restart system after installation.
Regards
Visruth
++Please click KUDOS / White thumb to say thanks
++Please click ACCEPT AS SOLUTION to help others, find this solution faster
**I'm a Volunteer, I do not work for HP**

Novell driver for promise raid controller PDC20276

[size=13]Is there a Novell driver for the promise raid controller on the KT3 Ultra2-R (MS-6380E) mainboard[/SIZE] this board uses the promise PDC20276 chipset.
The supplied disk only supports windows ;(
Can any one advise options thanks :P

CapricornC,
Since you have a KT3 Motherboard and you posted in the nVidia/AMD/SiS Motherboard Forum, I moved the thread to Via Forum for you.
Good Luck,
Richard

Remote not working right

I've had my FIOS about 2 months, put new batteries in remote and it is still not working right. Some things work fine. Other things stopped working - can't delete a DVR show, can't change channels with one digit, but it will if I add all 4 digits, info box on bottom of screen never disappears (unless I hit exit). What's wrong?
My second TV set-up is OK.
Solved!
Go to Solution.

netmouse wrote:
I've had my FIOS about 2 months, put new batteries in remote and it is still not working right. Some things work fine. Other things stopped working - can't delete a DVR show, can't change channels with one digit, but it will if I add all 4 digits, info box on bottom of screen never disappears (unless I hit exit). What's wrong?
My second TV set-up is OK.
Might not even be a remote issue. Have you tried rebooting the box?
If you do think it's the remote it's still under warranty.
You can get a free replacement easy within the dvr's menu.
Here is a page that tells you ways to get a replacement.
http://www.verizon.com/support/residential/tv/fiostv/remote+controls/troubleshooting/questionsone/12...
Get a new remote and if you still have the same issues then you'll know its the dvr that needs to be replaced.

Is there any way to redownload iOS 5 my iPod touch 4 th generation white 32 gig is not working right?

My iPod is not working right. It's slow and lags and just doesn't work and always exits apps. I was if there was any way to redownload ios5 because it does the same things after I've reset about 4 times. Please help! It's even lagging why I am typing this. The thing that I checked below are all of the things that are not working on my iPod.

You cannot reinstall iOS without doing a restore. But you might first try a software update. If you have iOS 5.0 or 5.0.1, you can update to iOS 5.1 by going to Settings > General > Software Update.

TS1398 Hello, my iPod touch is not working right. It says its connected but if I select App Store, safari and other apps that require wifi pops out a note saying either"error loading" or "cannot connect to iTunes Store" and would exit the app automaticall

Hello, my iPod touch is not working right. It says its connected but if I select App Store, safari and other apps that require wifi pops out a note saying either"error loading" or "cannot connect to iTunes Store" and would exit the app automatically. Please help.
Thank You.

See:
Can't connect to the iTunes Store

IPad 2 was updated to latest iOS 7 and has been not working right since. I have tried to do a restore but still continues to go into reboot mode by itself and very erratic. Can no longer trust it. I tried to complain to Apple but have to give them 20 buck

iPad has not worked right since it updated to latest software. Tried to question Apple about it but it costs 20 bucks just to lodge a complaint. Is this normal Apple behavior or am I missing something. Also anyone else having issues with upgrade to iOS7. It was working great until that point and now goes into reboot mode often and sometimes will continuously reboot several times. I have tried to restore but that didn't clear the problem. Any thoughts or help would be appreciated.

Greetings,
I've never seen this issue, and I handle many iPads, of all versions. WiFi issues are generally local to the WiFi router - they are not all of the same quality, range, immunity to interference, etc. You have distance, building construction, and the biggie - interference.
At home, I use Apple routers, and have no issues with any of my WiFi enabled devices, computers, mobile devices, etc - even the lowly PeeCees. I have locations where I have Juniper Networks, as well as Aruba, and a few Netgears - all of them work as they should.
The cheaper routers, Linksys, D-Link, Seimens home units, and many other no name devices have caused issues of various kinds, and even connectivity.
I have no idea what Starbucks uses, but I always have a good connection, and I go there nearly every morning and get some work done, as well as play.
You could try changing channels, 2.4 to 5 Gigs, changing locations of the router. I have had to do all of these at one time or another over the many years that I have been a Network Engineer.
Good Luck - Cheers,
M.

HT4623 My iPad mini is not working right ?? On some apps

My iPad mini is not working right on some apps

You can always try to reset your device and see if it helps matters any:
Device Reset (won't affect settings/data/music/apps/etc)
1. Press and hold (& continue to hold) BOTH the Sleep/Wake button & the Home button.
2. Continue to hold BOTH (ignoring any other messages that may show) until you see the Apple logo on the screen.
3. Release BOTH buttons when you see the Apple logo and allow the device to boot normally.

Since updating to 706 the sound on my ipad2 is not working right. On videos or music. There is constant distortion and what sounds like interference. Any ideas?

Since updating to 706 the sound on my ipad2 is not working right--on videos or music. There is distortion and some kind of interference at all times. Any ideas?

Has the unit EVER been jailbroke?
If "No," first try a system reset. It cures many ills and it's quick, easy and harmless...
Hold down the on/off switch and the Home button simultaneously until you see the Apple logo. Ignore the "Slide to power off" text if it appears. You will not lose any apps, data, music, movies, settings, etc.
If the Reset doesn't work, try a Restore. Note that it's nowhere near as quick as a Reset. It could take well over an hour! Connect via cable to the computer that you use for sync. From iTunes, select the iPad/iPod and then select the Summary tab. Follow the on-screen directions for Restore and be sure to say "yes" to the backup. You will be warned that all data (apps, music, movies, etc.) will be erased but, as the Restore finishes, you will be asked if you wish the contents of the backup to be copied to the iPad/iPod. Again, say "yes."
At the end of the basic Restore, you will be asked if you wish to sync the iPad/iPod. As before, say "yes." Note that that sync selection will disappear and the Restore will end if you do not respond within a reasonable time. If that happens, only the apps that are part of the IOS will appear on your device. Corrective action is simple - choose manual "Sync" from the bottom right of iTunes.
If you're unable to do the Restore, go into Recovery Mode per the instructions here. You WILL lose all of your data (game scores, etc,) but, for the most part, you can redownload apps and music without being charged again. Also, if you have IOS-7, read this.

T42 keyboard not working right, HELP PLEASE

My keyboard is not working right. If I push the key it wont work,but if I hold the key for a couple seconds then it works was told to replace the keyboard and I did with a new one. But it is still doing it. Can anyone tell me what the problem is. Model # R4U machine type 2378, OS XP-PRO , COA SP2 , S/N L3xxxxx.
Message Edited by scottzilla on 12-15-2008 10:05 PM
Moderator Note; s/n edited for members own protection
Message Edited by andyP on 12-16-2008 07:57 AM

It's the Quick Selection Tool in Photoshop Elements 9 and I'm trying to get the background and make it another layer so I can even out the color of the background then bring down the transparency. Not sure if that makes sense. I'm new to this.... Sometimes the area it will grab can go ...not fast.. but not slow. Sometimes it's like it's just messed up and literally takes 30 seconds to process each move. I rebooted my computer and re opened it and it helped a little. It's not clear what causes it when it messes up and when it doesn't. Just frustrating. It's probably user error because I'm so new at Photoshop. Thanks for your input. I really appreciate it.

Scroll-bar STILL not working right in 10.6.1 update

The scroll-bar is STILL NOT working right in the 10.6.1 update. I am not able to click anywhere on the scroll-bar and have the navigation go there. I have to drag the blamed thing where ever I want it to go. This problem only exist with the recent iTunes 10.6.x updates.

I have the new MacBook Pro 2010, Dell 3007WFP. No mirroring problemsat that or higher res. I was chagrined, however, to find out that while my 2007 15" MacBook Pro had no problems driving the Dell 30", the 2010 17" requires the Dual Link cable for $100 extra. ;>(
But it works fine.
ak

K8N Neo2 + NVRAID + Promise Raid Controller = not working right

Similar Messages

Maybe you are looking for