K8N Neo2 Plat and San Diego Core

What is the best bios with the San Diego Core? I'm currenlty running a AMD 3000+ Venice (LBBLE 0516CPBW) and want to switch. I'm currently running a Syar moded bios. I'm at work and don't know which one I'm running.

Same bios + new Win XP installation.
You really should take a look at the cpu-list.
All these cpu models are covered with the 1.B /C1 bioses;
http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_cpu_support_detail.php?UID=607&kind=1

Similar Messages

New K8N NEO2 PLAT. and SC-939 3200+ help needed...

Hello,
I have just upgraded my system with K8N Neo2 Plat. and sc-939 3200+ A64 Cpu.
There are several issues I need to resolve which are:
1- Although I change from BIOS the settings for AGP to 4x8x and enable fast writes, I still cant see them turned on from the Catalyst Control Center. Everything is greyed out what can I do? They all used to be on and agp was 8x with my K7N2 Delta board....
2- Although I installed the original drivers from the MSI CD, I couldn't get one of the network prts to install. Realtek installed OK. But other one is defined by the device manager as standart network adapter. What can I do?
3- I am brand new to A64 system so I do not know what setting to use from BIOS can you help me out, for instance there are values for HT such as x3 x4 x5 mine is set to x5? what is this? should I enable cool and quiet, I am not intended to do overclocking. Can you give me some tips for best performance?
My best regards.

Make sure your bios is up to date: version 1.5. Look at the sticky threads and use the information to enable hidden bios features. Disable ATI/NV speedup in the bios. Uninstall your drivers and reinstall. If the information is still greyed out, download the free version of Sandra here: http://downloads.guru3d.com/ and check the module under video system information. This will tell you if fast writes are enabled and your AGP setting. Leave the HT(hyper-transport) set to 5X unless you plan on oc'ing, if you do oc then may find you'll need to reduce it to 4X or 3X. Try downloading the latest driver for your network from the MSI website. Right click the device in device manager and select update, select specific location then "don't look...I'll choose", direct it to the file where you've unpacked the correct driver and then update.

K8N Neo2 platinum (nF3) + San Diego?

Will it work, does anyone know? I have a Venice now and a San Diego arriving on Friday, just wanted to know if it works or not so I may have to cancel the order if necessary. I wish MSI kept ahead like DFI on the BIOS front!

Hmm… seems like they have removed both venice and san diego from testing phase and OK status in the K8N Neo2 support list, which were there some days ago.
http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_cpu_support_detail.php?UID=607&kind=1
Something is going on – maybe 1.6 wasnt fully compatbile with venice/san diego - hopefully a new 1.7 bios ?
I can´t see why venice / san diego would not work with a proper biosupdate – but as you said – they are late with bios updates.

K8N Neo2 Plat and 1.B0 - No BIOS Setup Screen

With K8N Neo2 Platinum (MS-7025):
After flash to 1.B0 version, from 1.90, boots normally. But, hitting Delete key to go to BIOS Setup, all I get is a blank screen with a white cursor in upper left - Won't go to BIOS Setup.
Went back to 1.90 with no problems.
Is this a known problem with 1.B0 version?
Papa_K

http://homepages.nildram.co.uk/~chsmith/Syars_Bios_Collection/NEO2/
It's 70251b0.zip. A modded version of 1B that you can reach thru the above thread found in Syar's sig.
Let us know if it works for you too.
JB
EDIT. I recommend winflash. Don't use liveupdate.
If you loaded live update on your computer then you have winflash. Go to C:\Program Files\MSI\Live Update 3\FlashUty\Award but use it carefully, shutting down all other programs and selecting the boxes to clear cmos etc. as described here:
https://forum-en.msi.com/index.php?topic=86257.0

Problem with K8N neo2 plat. and ram

Hello everyone
Recently I had 2*512mo of PC3200 ( double side ), they hold all approximately 235mhz has 2.5/3/3/8 1T (tested separately)
But, when I puts them into dual they are stable under memtest always with 235 2.5/3/3/8 1T but are unstable under Windows, under xp they are stable until 207mhz maximum whereas they hold much higher under memtest
If I want to be stable A 235mhz under Windows it is necessary that I put them in 2T but y' has an enormous loss of perf
I tested different bios (1.37mod, 1.4 official, 1.41mod, 1.5 official, 1.8r3mod, 1.9 official and 1.B4mod) and always the same problem I also tested on port 1 and 3 (near to the CPU) and 2 and 4 but there it is still worse
Here if you have suggestion they are the welcomes
In advance thank you
Config
K8N neo2 platinium
Winchester 3200+
2*512mo chip infinéon
PS: sorry for my bad english

Hello, thanks for your answer
My ram is Apacer value here but in ship infineon
My power supply is a LC power 550w
My video card is an ATI 9600xt sapphire
The HTT/LDT is of 3x for a FSB of 235mhz ( ram synchro )
I have also tested desynchronized ram to 166 ( cpu stable: 283*8.5, ram: 218mhz ) but I have always this problem
Thanks

K8N Neo2 Plat and Audio Troubles (to put it lightly)

So it starts like this:
Old computer craps out, time for a new one. Buy the AMD64 PIB with the Neo2 Platinum on the nForce3 Ultra. And RAM, etc. Slap it all together, pick up a new set of speakers (I got 5.1 ability, I'll use it) plug 'em in and fire it up. It's fantastic, I'm blasting music and games, getting 100fps solid in everything, so I fire up ventrilo to talk to my buds.
"Dude...you're not saying anything"
Crap. First thing's first, I make sure I pluggd my mic in. Check. Audio settings. Ahhhh, microphone is muted. Click unmute. SSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSS. ? I'm getting feedback through my speakers. Not loud mic-right-next-to-the-speakers feedback, more like mic-pulled-just-short-of-out-of-feedback-range sounding feedback.
Alright, fine, driver must need to be updated. Take a peek in my device manager, head on over to RealTek, and can't find the driver. So I shoot them an e-mail, they respond within an hour with a link to the driver I wanted. Perfect. Update driver, reboot, fire ventrilo back up. Same exact problem. Off to nVidia for me. Download the Audio Driver Package. Gives me a zip with a folder in it. Drop it on my desktop, go to install the drivers through device manager again, point to the folder.....nothing. Apparently the driver I downloaded doesn't have the necesarry software for installing the driver. Now I'm agitated, now I'm here. Notice I've worked my way up the ladder and have been patient for quite some time. If anyone has any idea how to get my mic to start working (Yes, it's not broken, and yes, I've tried several others), now is the time to come forward. Otherwise I'm gonna be here hitting F5 all night. No one wants to see that, do they?

If you add a PCI sound you might have to disable the on-board audio in BIOS, or BIOS might do that for you automatically. In either case your problem would be fixed if the problem is with the mic port on your MB and assuming your mics are really ok. I'm not saying that they are not, I am just trying to explain what will/will not happen depending on what is/is not currently working.
I haven't purchased a sound card in a long time but I am wondering if you can get a really cheap one and maybe a really cheap mic and test them in your system. That way you can resolve what your problem really is. Then you can return the cheap ones and buy what ever you really want. I would hate to see you buy an expensive audio card and then find that the problem is somewhere that we haven't identified yet (tho I can't at this point think of anything else that might be wrong).
Or better yet maybe you can borrow a sound card and/or mic from a friend just for testiing.

3700+ san diego core and msi k8n neo2 platinum bios

will i need a bios update to get my 3700+ san diego core to work in my system. currently my motherboard bios is 1.5 Fedex sometime today is suppose to drop off my new 3700+ san diego core today. if i do need a bios, were can i get one for it to work.

Quote from: JCLogix on 05-May-05, 16:12:24
Offcially that board does not have support for San Diego at this time, so if you have got it working, as some people have it may have some wierd and wonderful effects on your system.
A guy on another forum got a response from a MSI tech that said they were working on it and to check their site regularly for a bios update. As far as "weird and wonderful effects" my setup has never run faster or smooter since I upgraded from my 3500+ Winchester. This is the 3rd day I've been running the San Diego, have had no problems other then having to use A64 tweaker to set RAM timing to 1T. 500Mhz overclock stock voltage, air-cooled, prime stable, I ran the torture test for 9 hours overnight!
Check it out!

K8N Neo2 Plat power and bios question

I have a K8N Neo2 Plat. I use a UltraProducts 500W xconnect PSU and a BFG 6800 GT OC.
A couple weeks ago the 6800 died. I contacted BFG and they sent me a new one.
The new one died the same way after a week. They said to check the power levels on the +12 rail.
In windows using softare tests it reports 13.58
in the bios it reports 12.22
both are over the allowed variance.
Ultra products told me to check with my motherboard manufacturer to see if there was a BIOS setting that would let me set the power on the +12V rail. Is that possible?
Is that something my K8N Neo2 Plat can do?

No, you cannot lower the 12V-rail by a bios setting. I really don't see what they mean by that.
Your motherboard does, however, regulate the power that comes from the power supply. Within certain margins it can lower the voltage and keep it steady. Your videocard can do the same. Now, depending on the tolerance (quality) of your hardware, you can vary on those margins. But on any piece of hardware, there is a point on which it cannot correct/lower a voltage that is too high. It then simply shuts down or dies.
To my opinion, the PSU-maker gave you a very funny piece of advice. What he actually says is that their psu may give too high a voltage (I talk about the 13+ now), but your hardware should correct this. That's not the way it works: they should make psu's that give 12V where it should. So, I'd demand a replacement. But, before you do: use a multimeter to measure the 12V-rail. You cannot trust the board's measurement too well.
But then, like Stick says, I think that 12.22 is within mentioned margins. 13.58V is too high. So, that's why you should first measure using a multimeter. Measure for a longer time. System idle, system full load. Write everything down and see how steady this psu is. If 12V dances arround, replace it.

K8N Neo2 Plat - Is 1.8 still the best bios?

Just bought new gfx card - Sapphire X1600Pro 256MB AGP - for my K8N Neo2 Plat setup (see sig for the rest).
I was getting 3dmark03 scores of 4400 to start with, then it has upped slowly to just over 6000 thanks to the various BIOS experts setup guides. I haven't found the Shgift F2 menu - is that only in later BIOSes ?
I'm only at BIOS 1.3 due to it's amazing stability with this setup, but now of course, I'm wondering if upping to, say, 1.8, might help improve things further ??
TIA

Hello !
The 1.8 bios is very good unless you are planning to run/update to an X2 dual core , then you will need a newer one for sure.
There is nothing faster and better with 1C , EasyBios 1C and my modded have better default values set in it ,EasyBios
have also better reworked layout (more user friendly) , but if you don't have any problems with your current one I would stick with it .
It's almost the same with my Neo1 system (Ms-7030) , I have this frozen at the 1.5b6 bios - with the Newcastle cpu in it
it actually works worse with the latest BIOS

NVidia Video Driver Causes Immediate freezing upon loading to desktop (K8N Neo2 Plat)...

after many a reinstall, order of loading drivers, i have finally traced my system's problem to the nvidia video drivers. i have no clue what to do. install everything (new nforce drivers, sp2, audio and ethernet drivers, windowsupdate, etc. EVERYTHING except running the nvidia video drivers package and the system does not freeze.
as soon as the video drivers are loaded, restart and once i get to the desktop it freezes. every single time. go into safe mode, remove video drivers, restart and the system doesn't freeze. fast write is disabled. all dram settings at auto. cool and quiet disableed. system specs are:
MSI K8N Neo2 Plat MB (bios is v1.3)
AMD64 3200+ Winchester Core
BFG 6800GT OC AGP Video Card
2*512MB Mushkin Dual Channel Blue Ram (2-3-3-6-1T at 200Mhz)
120GB WD Caviar 7200RPM 8MB Cache IDE HD
NEC ND3520A 16x DVD Burner
CoolerMaster Wave Master Aluminum Case
Coolermaster RS-450-ACLY Power Supply
any ideas?

well i'll be damned. spread spectrum. it was spread spectrum being enabled. there just isn't a more satifying feeling that thinking you figured out what was causing freezes and then finding out it's repeatable!!
spread spectrum on. freeze. reboot. freeze. reboot. freeze. spread spectrum disabled. reboot. no freeze. reboot. no freeze. reboot. no freeze. spread spectrum back on. reboot. freeze. reboot. freeze.
i love it.

Unidentified 10-12Pins inside the K8N Neo2 Plat

Hi guys,
I've just finished setting up my K8N Neo2 Plat into the case with the jumpers and cables etc. And there's sometihng interesting I discovered.
There is a set of jumpers or Pins, just above the JDB1 [D-Bracket pins] that seems to be unused and un-labelled in the Instruction manual.
The PCB has it labelled as JPC1 with a small arrow pointing downwards.
I searched thru the manual, and no sign of what it's used for.
Anyone else noticed this when they installed their board jumpers and pins?
Many thanks
mystify

LOL..you can pm to syar as he has the modded bios for 1C as i'm using his bios as nice and easy. But like what qyx say corecentre messing all you setting including the bios and stay away any DOT, C&Q if you're ocing your system. Better used manual way to set it in the bios. GD luck.

K8N Neo2 plat, no post issue cont'd.

Hi its me again, the guy with the intermittent "no post" k8n neo2 plat.
Loaded the 1b3 beta the other day, again 1 day later the box would not post, as usual no
indication on the D-bracket, just one flash of the keyboard, the fans span one half round.
Since it could run for 1month plus with 1a3 beta BIOS(no usb2.0 (I could not wait any longer wanted usb2.0 so I flashed to a newer bios)),
start thinking it could be something between these latter full versions and this.
Then saw a thread on the web about someone having a Winnie that his box also has issues when swapping for latter
version than 1.5, with 1.5 his plat run fine. Go figure.
So for the time being I switched it to v1.5 bios, lets see how long it holds.
oh btw, the CMOS clear "no effect" seem to be avoided, by unplugging every external
peripheral prior to doing the cmos clear.

Quote from: Mysticcal on 30-June-05, 06:26:41
...Speaker Beeps once, USB LEDS Hold at Green, Red, Green, Green...
Tried everything, don't know what to do
And for those that ask me, what HDs? What IDEs?
Go take an A+ Course please. No one with 2 cells of brain capacity would hook everything up on first boot not knowing if it will work or not...
Thanks, all help appreciated.
The Led display from your D-Bracket indicates it is stopping when it tries to initialise the floppy drive. You don't have one. No A+ course needed, just hook up your floppy or disable it in the BIOS. I have no floppy drive (I have no need) so have it disabled. Probably best to hook up all relevant devices that will enable a working machine. The BIOS is probably halting when it can't initialise a device. There would be no point in it proceeding if it doesn't have all devices needed for a bootable machine...
See D-Bracket guide here D-Bracket Guide
I'm only guessing.

Boot failure - k8n neo2 plat

Hi, I'm having trouble
Just purchased an MSI k8n neo2 plat mobo with an amd 64 3000+ and finally got her all setup... well minus the geforce 6600 gt arriving tomorrow and I still need to figure out what I'll do as far as memory goes. Ah but I forget myself... the problem at hand is this; I am unable to boot the system and the d-bracket indicates its current status is "Processor initialization..." Then nothing. Blank screen.
LED's btw:
red green
green red
thanks for any help
Sytem specs:
k8n neo2
amd xp 64 3000+
geforce 2 mx
1x mushkin pc2700 256mb (test mem)
60gb maxtor
generic cd-writer
PS is @POWER 430w with:
+3.3v = 28a
+5v = 40a
+12 = 17a

1)I'd go further than shturmovik in your 12v amps requirement you need at least 24a especially with your new graphic card.
see Basic Building Tips - Quote
As this pertains to A64's make sure that you have a power supply that is either approved for use by MSI/AMD or that you have plenty of amps on the 12 volt rail. Typically we have noted many issues based on stability with PSU's being rated at less than 24A on the 12v rail.
Power Consumption: NVIDIA vs. ATI
2)The D-Led Quote
Processor initialization
also covers memory issues as with the 64 the memory controller is on the CPU.
as your 1x mushkin pc2700 256mb (test mem) this rules out any dual channel problems.
which slot is it in.

Freezing issues with K8N Neo2 Plat & 6800 gt

Well I get random freezing during games. Sometimes it freezes for 5-10 seconds then comes back, while other times it just freezes and the sound comes back but not the game.
I had this problem when I first upgraded.
K8N Neo2 plat
1gb corsair xms 3200
athlon 64 3500
aslo have:
420-30? antec tru power supply. I cant remember exact number.
6800gt ultra
audigy 2 plat
Now I first posted my problem a while ago and someone told me to try chaning the HT to 4x instead of 5x. So I did and it worked. It worked for a few weeks and now the problems have come back.
Any Ideas?

Along with the above issues, I've also found that a lot of my gaming probs with the 6800 are due to it being a "bandwidth hog" & it's latency needs to be adjusted lower to enable the other devices on the PCI bus (i.e. sound card) to get enough bandwidth to function properly. This isn't noticeable until you start some heavy gaming with a lot going on at once...
If your game ever practically chugs to a halt when a lot of sounds are being produced, this is the main problem. Here's a way & some notes on how to deal with it. Just like every "tweak" though, it's not guaranteed to work for everyone but I got noticeable benefits from it.
- D/L (I got it @ guru3D) PCI Latency Tool & give the "Read Me" a quick once-over. Write down the values for your devices, in case you need/want to change 'em back. Most items are well labeled - the 6800 & your sound card will be what you are most interested in. I wouldn't mess with the rest of 'em, as they deal with low level system items that are best left alone. Unless you are truly an Uber Geek!
- The latency for my 6800 listed as a massive 248 clks! For some reason, I've read that ATI cards don't default at such a large value, which might explain why people don't seem to have as many performance issues with 'em. Anyhow lower the 6800 to a more "reasonable" value, like 128 or 64. 64 seemed to work best for me.
- Save the settings, reboot & test it out. You can experiement with the sound card latency too, in order to find what works best for you, but I wouldn't set it at less than it's default value (32).
Hope this helps.

K8N neo2 Plat problem with Inno3D 7600GS AGP, help pls...

Just got the new Inno3d 7600GS AGP card, after installed & while booting up my monitor keep going off and on then suddenly just went off...sometime system freeze when it reach deskstop.
Sometime lucky enough it will still there and the next few minute the system just freeze.
After several attemp & no choice, I unplug the power to the graphic card and the problem still exist.
I am using a HEC 350W PSU.
I change back to my old ati9200se card & no problem at all.
I changed to skyhawk 430W still same problem. even I boot up to safe mode still the same. Only time the monitor wouldn't go off untill it pass the winXP logo then the problem appear.
I got no problem when go to CMOS as well.
Already perform uninstall previous video driver, update latest nforce driver....all no use.
K8N Neo2 Plat
HEC 350W
2 harddisk (1 SATA & 1 IDE)
Any idea guys?
Thanks

What are your PSU amp for the +12V? What bios version are you using right now? Tried to disable the fast write in the Bios? Gd luck.

K8N Neo2 Plat and San Diego Core

Similar Messages

Maybe you are looking for