K8N Neo2 Plat Bios setting.

Just updated my bios using the liveupdate feature, frustratingly it resets all of your bios settings. I have 2 SATA hard drives set up in RAID 0, was poking through the bios enabling SATA RAID again, and came across the page that enables/disables DMA access on the IDE channels. I have the option to enable/disable it for the SATA drives as well as the IDE ones, should it be enabled like all the others? Or disabled?
Thanks

I got the same setup as you and have Sata1 and sata2 dma enabled.
Like with ide channels you loose loose performance when dma is disabled.
vanish

Similar Messages

K8N Neo2 Plat - Is 1.8 still the best bios?

Just bought new gfx card - Sapphire X1600Pro 256MB AGP - for my K8N Neo2 Plat setup (see sig for the rest).
I was getting 3dmark03 scores of 4400 to start with, then it has upped slowly to just over 6000 thanks to the various BIOS experts setup guides. I haven't found the Shgift F2 menu - is that only in later BIOSes ?
I'm only at BIOS 1.3 due to it's amazing stability with this setup, but now of course, I'm wondering if upping to, say, 1.8, might help improve things further ??
TIA

Hello !
The 1.8 bios is very good unless you are planning to run/update to an X2 dual core , then you will need a newer one for sure.
There is nothing faster and better with 1C , EasyBios 1C and my modded have better default values set in it ,EasyBios
have also better reworked layout (more user friendly) , but if you don't have any problems with your current one I would stick with it .
It's almost the same with my Neo1 system (Ms-7030) , I have this frozen at the 1.5b6 bios - with the Newcastle cpu in it
it actually works worse with the latest BIOS

K8N Neo2 Plat power and bios question

I have a K8N Neo2 Plat. I use a UltraProducts 500W xconnect PSU and a BFG 6800 GT OC.
A couple weeks ago the 6800 died. I contacted BFG and they sent me a new one.
The new one died the same way after a week. They said to check the power levels on the +12 rail.
In windows using softare tests it reports 13.58
in the bios it reports 12.22
both are over the allowed variance.
Ultra products told me to check with my motherboard manufacturer to see if there was a BIOS setting that would let me set the power on the +12V rail. Is that possible?
Is that something my K8N Neo2 Plat can do?

No, you cannot lower the 12V-rail by a bios setting. I really don't see what they mean by that.
Your motherboard does, however, regulate the power that comes from the power supply. Within certain margins it can lower the voltage and keep it steady. Your videocard can do the same. Now, depending on the tolerance (quality) of your hardware, you can vary on those margins. But on any piece of hardware, there is a point on which it cannot correct/lower a voltage that is too high. It then simply shuts down or dies.
To my opinion, the PSU-maker gave you a very funny piece of advice. What he actually says is that their psu may give too high a voltage (I talk about the 13+ now), but your hardware should correct this. That's not the way it works: they should make psu's that give 12V where it should. So, I'd demand a replacement. But, before you do: use a multimeter to measure the 12V-rail. You cannot trust the board's measurement too well.
But then, like Stick says, I think that 12.22 is within mentioned margins. 13.58V is too high. So, that's why you should first measure using a multimeter. Measure for a longer time. System idle, system full load. Write everything down and see how steady this psu is. If 12V dances arround, replace it.

Unidentified 10-12Pins inside the K8N Neo2 Plat

Hi guys,
I've just finished setting up my K8N Neo2 Plat into the case with the jumpers and cables etc. And there's sometihng interesting I discovered.
There is a set of jumpers or Pins, just above the JDB1 [D-Bracket pins] that seems to be unused and un-labelled in the Instruction manual.
The PCB has it labelled as JPC1 with a small arrow pointing downwards.
I searched thru the manual, and no sign of what it's used for.
Anyone else noticed this when they installed their board jumpers and pins?
Many thanks
mystify

LOL..you can pm to syar as he has the modded bios for 1C as i'm using his bios as nice and easy. But like what qyx say corecentre messing all you setting including the bios and stay away any DOT, C&Q if you're ocing your system. Better used manual way to set it in the bios. GD luck.

New K8N NEO2 PLAT. and SC-939 3200+ help needed...

Hello,
I have just upgraded my system with K8N Neo2 Plat. and sc-939 3200+ A64 Cpu.
There are several issues I need to resolve which are:
1- Although I change from BIOS the settings for AGP to 4x8x and enable fast writes, I still cant see them turned on from the Catalyst Control Center. Everything is greyed out what can I do? They all used to be on and agp was 8x with my K7N2 Delta board....
2- Although I installed the original drivers from the MSI CD, I couldn't get one of the network prts to install. Realtek installed OK. But other one is defined by the device manager as standart network adapter. What can I do?
3- I am brand new to A64 system so I do not know what setting to use from BIOS can you help me out, for instance there are values for HT such as x3 x4 x5 mine is set to x5? what is this? should I enable cool and quiet, I am not intended to do overclocking. Can you give me some tips for best performance?
My best regards.

Make sure your bios is up to date: version 1.5. Look at the sticky threads and use the information to enable hidden bios features. Disable ATI/NV speedup in the bios. Uninstall your drivers and reinstall. If the information is still greyed out, download the free version of Sandra here: http://downloads.guru3d.com/ and check the module under video system information. This will tell you if fast writes are enabled and your AGP setting. Leave the HT(hyper-transport) set to 5X unless you plan on oc'ing, if you do oc then may find you'll need to reduce it to 4X or 3X. Try downloading the latest driver for your network from the MSI website. Right click the device in device manager and select update, select specific location then "don't look...I'll choose", direct it to the file where you've unpacked the correct driver and then update.

K8n neo plat / bios hangs on save changes

hello. been trying to do the below OC, as mentioned elsewhere on this board. every time i try to save the changes into bios: it just hangs, drops the monitor connection, black screen. i have to clear cmos and reboot.
i know there is a problem on this board when you hit ENTER to change the HT multi, but i do not think i have that prob. i have been using pg up & down to change all my values in any case. i have tried both using f10 to save and backing out to the main menu to save. i also tried bumping both the vcore and vdimm in case they were underpowered. any other changes i do in bios, not relating to the HT multi seem to save fine...
any ideas?
Quote
If your 3500+ is a Venice core, moderate overclock on k8n neo2 plat is a "walk in the park".
-disable cool&quiet
-use default vcore
-set HT 3
-CPU multiplier manually set to 10.
-FSB set to 250MHz
-DRAM ratio set to 166MHz
-RAM timing set to 2.5-3-3-9@1T, if it is unstable set to 2T
This will bring it to 2500MHz. Check the CPU temperature under heavy load.

Quote from: snoww on 07-January-07, 17:00:50
i've tried the clock at 220, no go. i don't have aggressive timings on.
crap, yeah i wish i posted this in the OC forum, but if i post it there now, i'll be double posting. maybe a thread move is possible?
yep.
"i've tried the clock at 220, no go. i don't have aggressive timings on."
keep memory arround rated freq.(200mhz), setup 166 mem. index.
well change BIOS settings via steps, one by one to check and see which setting cause the issue and correct it.
Disable Cool'N'Quite, Disable All Spectrums, set PCI-E freq. to 101Mhz. don't bump mem. vcore (give only when need) too much vcore will cause instability too.

K8N Neo2 Plat - No start beep...

Hello,
Does anyone finaly found why with the K8N Neo2 Plat board sometime the puter wont beep and start? Need to shut it down and try a few time before it does beep and start the puter? Basicaly the problem is that when you start the computer you should hear a beep then you will see something in your monitor screen such as drive information, cpu speed and memory then it will search for cd, floppy boots and then windows will start if no boots are found but there is no beep and nothing appear on the screen then you have to shutdown the puter and try a few reboot then somehow it decide to beep and start...
I've read many thread and I tryed this so far:
-Removed Keyboard and mouse
-Tryed to push harder the video card in its slot
-Tryed to push harder the memory in their slot
-Tryed to push harder the sound card in its slot
-Tryed to push harder the LAN card in its slot
-Tryed to start the computer without the monitor
-Tryed to remove all my additional fans to give more power.
-Tryed to reinstall Windows XP SP2
-Took a look at the cpu and cpu fan
-Changed my video card for a new one
-Tryed to remove memory and it only does a long beep and no system start at all. (which is normal)
-Removed Spectrum, aggressive timing in bios, no overclock setting also.
I have tryed all these and still have problem starting my computer. Is it a motherboard problem? a Power supply problem? a Cpu problem? A memory problem? If anyone can help to find out it would be great!
By the way maybe its because im not english but I dont know what PSU mean, can anyone tell me? Thanks
Sorry for my english!

You might want to try a better PSU as the Antec SL400 does only 18amps....
It's overloaded at 23A....see the specs....
Spec of the Antec SL400

A few K8N Neo2 Plat problems

Just getting this new rig up and going K8N Neo2 Plat with a 3200 Winchester 90nm CPU and 1GB (2x512) OCZ PC3200 Plat. rev2. My memory is not showing to be running in Dual Channel. and Sandra bandwidth is horrible to say the least. I have flashed to the latest bios that MSI has on the site, are their any better ones? I see some people running different versions of 1.3 bios, where are they? I have two Barracuda 80Gb S-ATA set up on #3-4 Sata connectors too in Raid (0).

Skeen, Duke is right. I have the same memory and you MUST use slot 1&2 for dual channel support. Look inthe manual on the page about memory. It gives 2 charts. The first one is for dual channel memory and the second one is for normal memory. Also I did a Sandra test that is somwhere here in the forums where I posted the results with 1&2 and 3&4 and 1&2 was slightly faster. Use them (the ones closest to the CPU).

K8N Neo2 plat, no post issue cont'd.

Hi its me again, the guy with the intermittent "no post" k8n neo2 plat.
Loaded the 1b3 beta the other day, again 1 day later the box would not post, as usual no
indication on the D-bracket, just one flash of the keyboard, the fans span one half round.
Since it could run for 1month plus with 1a3 beta BIOS(no usb2.0 (I could not wait any longer wanted usb2.0 so I flashed to a newer bios)),
start thinking it could be something between these latter full versions and this.
Then saw a thread on the web about someone having a Winnie that his box also has issues when swapping for latter
version than 1.5, with 1.5 his plat run fine. Go figure.
So for the time being I switched it to v1.5 bios, lets see how long it holds.
oh btw, the CMOS clear "no effect" seem to be avoided, by unplugging every external
peripheral prior to doing the cmos clear.

Quote from: Mysticcal on 30-June-05, 06:26:41
...Speaker Beeps once, USB LEDS Hold at Green, Red, Green, Green...
Tried everything, don't know what to do
And for those that ask me, what HDs? What IDEs?
Go take an A+ Course please. No one with 2 cells of brain capacity would hook everything up on first boot not knowing if it will work or not...
Thanks, all help appreciated.
The Led display from your D-Bracket indicates it is stopping when it tries to initialise the floppy drive. You don't have one. No A+ course needed, just hook up your floppy or disable it in the BIOS. I have no floppy drive (I have no need) so have it disabled. Probably best to hook up all relevant devices that will enable a working machine. The BIOS is probably halting when it can't initialise a device. There would be no point in it proceeding if it doesn't have all devices needed for a bootable machine...
See D-Bracket guide here D-Bracket Guide
I'm only guessing.

NVidia Video Driver Causes Immediate freezing upon loading to desktop (K8N Neo2 Plat)...

after many a reinstall, order of loading drivers, i have finally traced my system's problem to the nvidia video drivers. i have no clue what to do. install everything (new nforce drivers, sp2, audio and ethernet drivers, windowsupdate, etc. EVERYTHING except running the nvidia video drivers package and the system does not freeze.
as soon as the video drivers are loaded, restart and once i get to the desktop it freezes. every single time. go into safe mode, remove video drivers, restart and the system doesn't freeze. fast write is disabled. all dram settings at auto. cool and quiet disableed. system specs are:
MSI K8N Neo2 Plat MB (bios is v1.3)
AMD64 3200+ Winchester Core
BFG 6800GT OC AGP Video Card
2*512MB Mushkin Dual Channel Blue Ram (2-3-3-6-1T at 200Mhz)
120GB WD Caviar 7200RPM 8MB Cache IDE HD
NEC ND3520A 16x DVD Burner
CoolerMaster Wave Master Aluminum Case
Coolermaster RS-450-ACLY Power Supply
any ideas?

well i'll be damned. spread spectrum. it was spread spectrum being enabled. there just isn't a more satifying feeling that thinking you figured out what was causing freezes and then finding out it's repeatable!!
spread spectrum on. freeze. reboot. freeze. reboot. freeze. spread spectrum disabled. reboot. no freeze. reboot. no freeze. reboot. no freeze. spread spectrum back on. reboot. freeze. reboot. freeze.
i love it.

Freezing issues with K8N Neo2 Plat & 6800 gt

Well I get random freezing during games. Sometimes it freezes for 5-10 seconds then comes back, while other times it just freezes and the sound comes back but not the game.
I had this problem when I first upgraded.
K8N Neo2 plat
1gb corsair xms 3200
athlon 64 3500
aslo have:
420-30? antec tru power supply. I cant remember exact number.
6800gt ultra
audigy 2 plat
Now I first posted my problem a while ago and someone told me to try chaning the HT to 4x instead of 5x. So I did and it worked. It worked for a few weeks and now the problems have come back.
Any Ideas?

Along with the above issues, I've also found that a lot of my gaming probs with the 6800 are due to it being a "bandwidth hog" & it's latency needs to be adjusted lower to enable the other devices on the PCI bus (i.e. sound card) to get enough bandwidth to function properly. This isn't noticeable until you start some heavy gaming with a lot going on at once...
If your game ever practically chugs to a halt when a lot of sounds are being produced, this is the main problem. Here's a way & some notes on how to deal with it. Just like every "tweak" though, it's not guaranteed to work for everyone but I got noticeable benefits from it.
- D/L (I got it @ guru3D) PCI Latency Tool & give the "Read Me" a quick once-over. Write down the values for your devices, in case you need/want to change 'em back. Most items are well labeled - the 6800 & your sound card will be what you are most interested in. I wouldn't mess with the rest of 'em, as they deal with low level system items that are best left alone. Unless you are truly an Uber Geek!
- The latency for my 6800 listed as a massive 248 clks! For some reason, I've read that ATI cards don't default at such a large value, which might explain why people don't seem to have as many performance issues with 'em. Anyhow lower the 6800 to a more "reasonable" value, like 128 or 64. 64 seemed to work best for me.
- Save the settings, reboot & test it out. You can experiement with the sound card latency too, in order to find what works best for you, but I wouldn't set it at less than it's default value (32).
Hope this helps.

K8N neo2 Plat problem with Inno3D 7600GS AGP, help pls...

Just got the new Inno3d 7600GS AGP card, after installed & while booting up my monitor keep going off and on then suddenly just went off...sometime system freeze when it reach deskstop.
Sometime lucky enough it will still there and the next few minute the system just freeze.
After several attemp & no choice, I unplug the power to the graphic card and the problem still exist.
I am using a HEC 350W PSU.
I change back to my old ati9200se card & no problem at all.
I changed to skyhawk 430W still same problem. even I boot up to safe mode still the same. Only time the monitor wouldn't go off untill it pass the winXP logo then the problem appear.
I got no problem when go to CMOS as well.
Already perform uninstall previous video driver, update latest nforce driver....all no use.
K8N Neo2 Plat
HEC 350W
2 harddisk (1 SATA & 1 IDE)
Any idea guys?
Thanks

What are your PSU amp for the +12V? What bios version are you using right now? Tried to disable the fast write in the Bios? Gd luck.

K8N Neo2 Plat - computer wont boot. RMA?

as the title suggests, I have a K8N Neo2 Plat with an amd athlon 64 3800+ and 2x512mb OCZ PC3700EB Platinum ram. Everything has worked great for the past year. However this weekend when I came home from school my pc wouldn't boot up. I plugged in all the cables, turned on the PSU, and hit the power button and the fans spun for about half a second then nothing. I tried again several times and the fans didn't even spin. I tried several plugs in the house, still nothing. Thinking it was the PSU (Antec NeoPower480) I bought a new one today and tried that. Still nothing. I even tried shorting the power switch on the case in case it's stopped working. still nothing. I'm quite knowledgeable about computers so it's not a silly newbie mistake. A friend of mine who does computer repairs thinks it's the motherboard, and I agree.
I was going to try RMAing it - do you think I should, and is the process relatively easy/painless? (FYI I'm Canadian)

Strip it down to a basic setup, CPU, 1 stick of ram (try different ram) and graphic card. This is all you need to boot and get into BIO.
If you can get into BIO then add one device at a time until you find the faulty piece, if you are not able to get it to boot then pull the graphic card and try to boot, you should get some beeps, do the same with the ram. If you don't get any beeps then it is a good chance it is your MB.

Looking for cheapest ram to go with the k8n neo2 plat

looking for the cheapest compatable 1GB dc kit for the msi k8n neo2 plat
any suggestions

Yea,
I gotta give a shout out for the Corsair Value Select series also. I ran it for years in cheap systems I built for friends without any problems at all. Newegg has it pretty cheap (under $100 bucks).
I think their cheapest starts at 79$ bucks for DDR400
http://www.newegg.com/Product/Product.asp?Item=N82E16820145440
good luck
doggy

Can I use this hard drive with my K8N Neo2 Plat?

Can I use this http://www.zipzoomfly.com/jsp/ProductDetail.jsp?ProductCode=101220-12 hard drive with my K8N Neo2 Plat?

Quote from: Richard on 26-September-05, 00:25:21
JustinSane,
The short answer is:
Yes
Take Care,
Richard
LOL, thanks.

K8N Neo2 Plat Bios setting.

Similar Messages

Maybe you are looking for