K8N neo2 Plat problem with Inno3D 7600GS AGP, help pls...

Just got the new Inno3d 7600GS AGP card, after installed & while booting up my monitor keep going off and on then suddenly just went off...sometime system freeze when it reach deskstop.
Sometime lucky enough it will still there and the next few minute the system just freeze.
After several attemp & no choice, I unplug the power to the graphic card and the problem still exist.
I am using a HEC 350W PSU.
I change back to my old ati9200se card & no problem at all.
I changed to skyhawk 430W still same problem. even I boot up to safe mode still the same. Only time the monitor wouldn't go off untill it pass the winXP logo then the problem appear.
I got no problem when go to CMOS as well.
Already perform uninstall previous video driver, update latest nforce driver....all no use.
K8N Neo2 Plat
HEC 350W
2 harddisk (1 SATA & 1 IDE)
Any idea guys?
Thanks

What are your PSU amp for the +12V? What bios version are you using right now? Tried to disable the fast write in the Bios? Gd luck.

Similar Messages

MOVED: [Athlon64] Msi K8N Neo2 Platinum problems with Patriot Ram

This topic has been moved to AMD64 nVidia Based board.
[Athlon64] Msi K8N Neo2 Platinum problems with Patriot Ram

First post, whoo hooo
So what version of BIOS are u running? I recently installed the two newest versions 2.0 and 2.1, and they both give me problems. With the latest (2.1) I'm getting the same error as you. Returning back to previous BIOS fixed my problems. Oh yeah, my RAM is Kingston Hyper-X, so i don't think thats your problem.
Let me know if you fix it, thats why im here, .

A few K8N Neo2 Plat problems

Just getting this new rig up and going K8N Neo2 Plat with a 3200 Winchester 90nm CPU and 1GB (2x512) OCZ PC3200 Plat. rev2. My memory is not showing to be running in Dual Channel. and Sandra bandwidth is horrible to say the least. I have flashed to the latest bios that MSI has on the site, are their any better ones? I see some people running different versions of 1.3 bios, where are they? I have two Barracuda 80Gb S-ATA set up on #3-4 Sata connectors too in Raid (0).

Skeen, Duke is right. I have the same memory and you MUST use slot 1&2 for dual channel support. Look inthe manual on the page about memory. It gives 2 charts. The first one is for dual channel memory and the second one is for normal memory. Also I did a Sandra test that is somwhere here in the forums where I posted the results with 1&2 and 3&4 and 1&2 was slightly faster. Use them (the ones closest to the CPU).

K8N Neo2 Driver Problem with PCI Bridge.

I updated the Bios on this machine last night to 1.04 from 1.03
K8N - Neo2
AMD 3500+ Retail Kit with Cooler
Antec True430W 3.3v/28A 5v/36A 12v/26A
OCZ 2X512 EL DDR400 PC 3200 Plat Ed Dual Channel
Seagate Barracuda 120g 7200 rpm SATA
TSST Corp DVD-ROM TS-H
ATI Radeon 9000 64mb AGP
Windows XP SP2
It started acting funny several hours after the update of the Bios, this AM it spontaneously rebooted and when it came up there was an error message about a damaged or corrupt Windows system file and suggested inserting the Windows Disk, which was done and then the system booted into windows. But the found new hardware came up and wanted driver for the PCI bridge, which I wasn't sure where it was so I let it complete without finding it and this is the error when I go to control panel/system/hardware/device mgr
Where do I get this driver? Is it on the driver disk that came with the motherboard? I don't remember having to install a driver for the PCI bridge.
thanks

OK I thought I'd post the resolution to my problem.
After my initial posts the machine not only became unstable but it wouldn't boot into windows saying there was a corrupt Windows System File.
1. It occured to me that when I downloaded the new bios and applied it that I had failed to customize the DRAM settings in the bios. This was important because when I was building the machine I couldn't get Windows XP to install it always pooped out someplace early in the install. At the time I was using default DRAM settings. But I came here and read through the forum and found a sticky at the top of the forum that had settings for a number of different memory sticks including mine. So I went back and updated my bios with those setting. Voila everything was cool and I was able to load windows and move forward. But I forgot that, and I attribute the instability of the system to that, wheter or not it was why the system eventually corrupted system board dirvers I don't know. But I did change that, as the system would boot but just not boot windows.
2. Next, I decided to attempt to repair my windows install. However first since I had already applied SP2, and my Install disk was just the plain retail without any Service Packs. I decided to make a new bootable install disk with SP2 slipstreamed into it so when I repaired I wouldn't have to reapply SP2. Here's the method that I used.
http://www.helpwithwindows.com/WindowsXP/winxp-sp2-bootcd.html
3. Utilized the windows repair feature of windows setup.
4. That worked my computer now booted into windows and I didn't lose data or configurations....whew!!
5. I still how ever was stuck with the original problem that started this thread..rats!! I thought SP2 would fix that.
6. I tried several times to get XP to update the driver, but I couldn't. I even tried to select the driver from the list that is one of the optioins when you are updating drivers. I found some but I wasn't sure which one that had PCI bridge in it was the right one. But the fact that when I was looking at the list of mfg only Compaq and NVidia were available. So a light bulb went off and opened up MSI Live and looked at what was available in drivers, and sure enought there was a NVida driver. So I figured I have nothing to lose.
7. Next I downloaded the latest NVida nForce3 system driverfrom MSI and applied.
8. Bingo that worked, no more yellow ?'s in my hardware list.
Machine working fine now. Still don't know if failing to insert the proper DRAM stuff caused this but it all started with the new bios so I am assuming it had some part.

K8N Neo2 plat problems. sound/boot/network

I just love the mobo. One of the best I ever had. But recently Ive run into som trouble with it.
When i boot it sometime hangs and the d-bracket tells me it is because of the floppy drive controller. Kinda weird since ive turned it off in the bios and I dont got a floppy connected. Ive read a little on this site and got to the conclusion that it is probably my PSU. A real cheap one that came with my case to around 30 €. Its only a 300w and it is due to a change. But i find it peculiar that i has run fine for several months.
When i got the mobo and i booted it came with an boot option that had something to do with the network. If you pressed shift+f11 or something like that you would enter a menu where it was possible to configure several network boot options and the possibility to turn it off. I did and now i cant get it back? Not that i miss it but i might use it later on and i am sure it can be reenabled. But resetting cmos by jumper or removing the batteri doesnt do it. How do i do it?
And then after messing around with a frontpanel audio thing in my case the onboard sound stopped working. Ive reset it to standard by putting the jumpers where they belong and not using the frontpanel. But still no sound.
Guess that was all my trouble hope that youll be able to help me
Thanks in advance

Know pepole with same case/PSU as me (with "only" 17A on the 12V) and morew power demanding HW (9800xt) ... no probs anywere....
I belive that poeple shuld be aware of that not all problems are caused by having a PSU with less than 24A@12V rail....
I am getting a little tired of all the "Buy a new PSU" - answers... Willing to get in a debate on this.
BTW - fromt his post: https://forum-en.msi.com/index.php?topic=72160.0
MB : Neo
GFX: 5900XT oc 460/850
PSU : BeQuiet 400W 1.3 Color
12 V rail : 20A
Drive value : 5p
Cpu : 2,2ghz@2,4ghz
Status : OK
MB : Neo2
GFX: X800pro@XT PE 527/605
PSU : BeQuiet Blackline 450W
12 V rail : 5V 45A / 12V 22A / 3.3V 28A
Drive value : 4P
Status : OK, good overclock
MB : MSI K8N Neo2-54G Platinum
GFX: Connect3D Radeon 9800 Pro
PSU : 400W Zalman (ZM400A-APF)
12 V rail : 15A (1st generation)
Drive value : 7P
Status : OK, running GREAT
MB : Neo2
GFX: X800pro
PSU : BeQuiet Blackline 450W
12 V rail : 5V 45A / 12V 22A / 3.3V 28A
Status : OK
MB : Neo2
GFX: 9600PRO / 128MB
PSU : Seasonic 350W
12 V rail : 19 A
Drive value : 3p
Status : OK
... and mine (signature)
Also;

K8N Neo2: Another problem with the BIOS 1.9

I flashed my K8N Neo2 with the BIOS 1.9, I lost the MAC address of the NVIDIA NIC. I fixed the problem reflashing the BIOS with the /nvmac:XXXXXXXXXXXX /wb options. Loaded the default settings and set the boot priority, the new BIOS is unable to boot from my Adaptec 19160 SCSI controller: it try always to boot to the NVIDIA NIC. It seems that the NVIDIA NIC has a higher boot priority than other external boot devices and it's impossible to change it.
The settings are:
First boot divice: Floppy
Secind boot device: Hard-Disk
Third boot device: CD-Rom
Hard disk boot priority:
1. Adaptec SCSI
2. NV RAID
3. Other boot device
I reflashed the BIOS with the old 1.8 and now the system works well ...
Thank you for the attention

See Thread this index called "Neo2 bios flash to 1.9 = dead nvidia lan"

RESOLVED - K8N Neo2 Platinum problem with large Seagate disk

Hi All,
I've been running this system for 4 years and I'm very happy with it. But I've run into a problem:
I'm trying to exchange my 120 GB Seagate Barracuda systemdisk with a 500 GB Barracuda and I can't install XP with SP2.
First I tried to clone the old HD with Norton Ghost and Acronis True Image. The cloning looked fine but after taking the old HD out and moving the new one to P-ATA 1 as Primary Master I get an "error - no operating system found". I also tried a fresh install from CD. After the CD reboots the system I get the same error.
The HD is present in BIOS with the right parameters and all is looking well - but still no go.
I've fiddled around in BIOS (vers. 1.3) with the different settings (LBA, Large, Auto, Csh.) The last 2 options gives the "no operating system" error and the first 2 gives a "disk error" although Seagate says that I should change settings to "LBA".
I only have the new HD in the machine. I also tried fixboot and fixmbr. I can see all the installed files when I put it in as a slave.
So my question is:
Does the K8N Neo2 Platinum have a problem with large hd's as system disk?
Or is this a Seagate or Windows problem ?
Any help is much appreciated!
Mads

Actually that was the first thing I did just to see if the drive worked :-) - except that I had it as master on the second ide cable. It formats like it should and all partitions report "healthy". The only difference is that the new drives c-partition is set as active (can't find a way to change it back) - while the old one is set as system. Could this make a difference ?
Since neither cloning nor a fresh install works I think the problem is something else. Maybe I should try Seatools and see if that makes any difference.
Thank's all for help so far! - Other suggestions ?

MSI K8N neo2 platinum PROBLEM WITH MAXTOR 300 SATA2

hi I got an enormous problem configuring this drive on the msi k8n neo2platinum (bios 1.9)
Simply the bios see the hd maxtor 300 on sata2 channel (I got another maxtor sata1 on first channel) but when loading windows it freezes.
What I have to do please?
thanx

BTW -
Here's a thread about your prob to check out. I thought it was totally solved for all nvidia chipsets, guess not. Nf3's seem to still have it to some extent. It seems Maxtor is the one that "dropped the ball" this time...
https://forum-en.msi.com/index.php?topic=93492.0

K8N Neo2 Plat - Trouble with Adaptec 19160 SCSI

Hi, Using BIOS 1.9 and installed an Adaptec 19160 a few days ago to mainly control a tape drive.
When the machine is going through POST, there is a message that comes up just after the Nvidia RAID prompt to the effect that the machine is unable to load the option ROM, presumably because it's clashing with the NVRAID BIOS (if I disable NVRAID in the BIOS, I am able to see the Adaptec option ROM prompt to press <ctrl><A> to go into the card diags).
Anyone else seen this problem and managed to get over it? Time was when you could change an Adaptec cards mem address and IRQ from the onboard diags, but you don't seem able to do that anymore.
The card still works, but if I want to use SCSI disks, I'm afraid it probably won't.

Problem is :
Bios can't invoke a addin card with nvraid enabled (aka' the invoke error string with the addin cards vendor ID).
What kind of card it is doesn't seem to matter with bioses above 1.9x .
I have SIL 3112 SATA addincard , same thing ...

MOVED: MSI K8N neo2 platinum PROBLEM WITH MAXTOR 300 SATA2

This topic has been moved to AMD64 nVidia Based board.
https://forum-en.msi.com/index.php?topic=93611.0

BTW -
Here's a thread about your prob to check out. I thought it was totally solved for all nvidia chipsets, guess not. Nf3's seem to still have it to some extent. It seems Maxtor is the one that "dropped the ball" this time...
https://forum-en.msi.com/index.php?topic=93492.0

Boot failure - k8n neo2 plat

Hi, I'm having trouble
Just purchased an MSI k8n neo2 plat mobo with an amd 64 3000+ and finally got her all setup... well minus the geforce 6600 gt arriving tomorrow and I still need to figure out what I'll do as far as memory goes. Ah but I forget myself... the problem at hand is this; I am unable to boot the system and the d-bracket indicates its current status is "Processor initialization..." Then nothing. Blank screen.
LED's btw:
red green
green red
thanks for any help
Sytem specs:
k8n neo2
amd xp 64 3000+
geforce 2 mx
1x mushkin pc2700 256mb (test mem)
60gb maxtor
generic cd-writer
PS is @POWER 430w with:
+3.3v = 28a
+5v = 40a
+12 = 17a

1)I'd go further than shturmovik in your 12v amps requirement you need at least 24a especially with your new graphic card.
see Basic Building Tips - Quote
As this pertains to A64's make sure that you have a power supply that is either approved for use by MSI/AMD or that you have plenty of amps on the 12 volt rail. Typically we have noted many issues based on stability with PSU's being rated at less than 24A on the 12v rail.
Power Consumption: NVIDIA vs. ATI
2)The D-Led Quote
Processor initialization
also covers memory issues as with the 64 the memory controller is on the CPU.
as your 1x mushkin pc2700 256mb (test mem) this rules out any dual channel problems.
which slot is it in.

Freezing issues with K8N Neo2 Plat & 6800 gt

Well I get random freezing during games. Sometimes it freezes for 5-10 seconds then comes back, while other times it just freezes and the sound comes back but not the game.
I had this problem when I first upgraded.
K8N Neo2 plat
1gb corsair xms 3200
athlon 64 3500
aslo have:
420-30? antec tru power supply. I cant remember exact number.
6800gt ultra
audigy 2 plat
Now I first posted my problem a while ago and someone told me to try chaning the HT to 4x instead of 5x. So I did and it worked. It worked for a few weeks and now the problems have come back.
Any Ideas?

Along with the above issues, I've also found that a lot of my gaming probs with the 6800 are due to it being a "bandwidth hog" & it's latency needs to be adjusted lower to enable the other devices on the PCI bus (i.e. sound card) to get enough bandwidth to function properly. This isn't noticeable until you start some heavy gaming with a lot going on at once...
If your game ever practically chugs to a halt when a lot of sounds are being produced, this is the main problem. Here's a way & some notes on how to deal with it. Just like every "tweak" though, it's not guaranteed to work for everyone but I got noticeable benefits from it.
- D/L (I got it @ guru3D) PCI Latency Tool & give the "Read Me" a quick once-over. Write down the values for your devices, in case you need/want to change 'em back. Most items are well labeled - the 6800 & your sound card will be what you are most interested in. I wouldn't mess with the rest of 'em, as they deal with low level system items that are best left alone. Unless you are truly an Uber Geek!
- The latency for my 6800 listed as a massive 248 clks! For some reason, I've read that ATI cards don't default at such a large value, which might explain why people don't seem to have as many performance issues with 'em. Anyhow lower the 6800 to a more "reasonable" value, like 128 or 64. 64 seemed to work best for me.
- Save the settings, reboot & test it out. You can experiement with the sound card latency too, in order to find what works best for you, but I wouldn't set it at less than it's default value (32).
Hope this helps.

Looking for cheapest ram to go with the k8n neo2 plat

looking for the cheapest compatable 1GB dc kit for the msi k8n neo2 plat
any suggestions

Yea,
I gotta give a shout out for the Corsair Value Select series also. I ran it for years in cheap systems I built for friends without any problems at all. Newegg has it pretty cheap (under $100 bucks).
I think their cheapest starts at 79$ bucks for DDR400
http://www.newegg.com/Product/Product.asp?Item=N82E16820145440
good luck
doggy

Can I use this hard drive with my K8N Neo2 Plat?

Can I use this http://www.zipzoomfly.com/jsp/ProductDetail.jsp?ProductCode=101220-12 hard drive with my K8N Neo2 Plat?

Quote from: Richard on 26-September-05, 00:25:21
JustinSane,
The short answer is:
Yes
Take Care,
Richard
LOL, thanks.

K8N Neo2 Plat - Is 1.8 still the best bios?

Just bought new gfx card - Sapphire X1600Pro 256MB AGP - for my K8N Neo2 Plat setup (see sig for the rest).
I was getting 3dmark03 scores of 4400 to start with, then it has upped slowly to just over 6000 thanks to the various BIOS experts setup guides. I haven't found the Shgift F2 menu - is that only in later BIOSes ?
I'm only at BIOS 1.3 due to it's amazing stability with this setup, but now of course, I'm wondering if upping to, say, 1.8, might help improve things further ??
TIA

Hello !
The 1.8 bios is very good unless you are planning to run/update to an X2 dual core , then you will need a newer one for sure.
There is nothing faster and better with 1C , EasyBios 1C and my modded have better default values set in it ,EasyBios
have also better reworked layout (more user friendly) , but if you don't have any problems with your current one I would stick with it .
It's almost the same with my Neo1 system (Ms-7030) , I have this frozen at the 1.5b6 bios - with the Newcastle cpu in it
it actually works worse with the latest BIOS

K8N neo2 Plat problem with Inno3D 7600GS AGP, help pls...

Similar Messages

Maybe you are looking for