K8N Neo2 Platinum 54G BIOS problem

I recently bought a MSI K8N Neo2 Platinum-54G mainboard with W7025NMS v1.3  092204 revision of BIOS.
AMD Athlon64 3000+ 939 is installed on the mainboard, with 2x512 GEIL PC3200 memory modules in dual channel configuration working on default frequency of 200MHz. CPU is recognized correctly as AMD Athlon64 3000+ on startup.
Mainboard’s BIOS seems to be corrupted. In Cell Menu options, in the upper left part of the screen (printed blue) are processor and DDR working timings:
Current CPU Clock 1810MHZ, Current DDR Clock 200MHz.
Aggressive Timings and Dynamic Overclocking values are [Disabled] (processor working on its defaulf settings); Spread Spectrum is [Disabled] while all DRAM Configuration settings are set to [Auto].
While entering HT frequency settings, (locked to [x5])  there are no other values to select – empty, and there is no way to leave it (ESC doesn’t help, the only thing possible to do is to reset the computer by pressing the Reset button on the chassis), but  the HT frequency settings were enabled when I loaded Fail-Safe settings, offering [1x], [1.5x], [2x], [2.5x], [3x], [4x], [5x].
Adjust CPU Ratio settings offer only [StartUp], [x4]~[x9] values, but as I understood by reading the manual there should be [StartUp], [x4]~[x20].
CPU Voltage, Memory Voltage and AGP Voltage are set to default.
CPU-Z, as well as SiSoft Sandra 2004 and SiSoft Sandra 2005 and MSI CORE CELL show that processor works at a core speed ~1005MHz, showing multiplier locked on x5.0 and HTT locked at ~200MHz, while the voltage is ~1.05V!
I downloaded the latest BIOS revision (v1.4), did the BIOS flash, but the problem remains!
Anybody, help!

Quote
HT frequency
is a known fault in bios & is easily sorted Bas HT Bios Error
Quote
CPU Ratio settings
AMD64 CPOU's have a lock on CPU ratios which varies according to the specification of the chip. therefore the multiplier available in your bios stops at the max multiplier allowed by amd for your cpu.
As an example i'm running a 3200 754 which has a maximum muliplier of 11 so that is the max i see in bios.
this guide may help Bios Guide

Similar Messages

  • K8N Neo2 Platinum, suddenly has problems

    This is the first system listed in my signature. This PC has been working well since it was built a couple of years ago. Recently, it seemed that the graphics were a bit taxed (I do some desktop publishing), and the system was running slower than normal. So I figured it might be time for a new video card. Installed a X1650PRO 256M and no post, no display. Checked that everything was seated properly, verified all connections, and tried again, nothing. Put the old card back in, nothing. Kicked it a few times and put the new card in with my fingers crossed, and she booted up. This was about a week ago. The system has been acting funky ever since with incomplete startups, random freezes, no display on boot, running very slow, and one time, Bios didn't see the hard drive array on POST. My first thought was that the power supply was overtaxed with the new card, but I am also considering a hard drive problem. Looking for some input... thanks

       PC Power&Cooling 

  • RESOLVED - K8N Neo2 Platinum problem with large Seagate disk

    Hi All,
    I've been running this system for 4 years and I'm very happy with it. But I've run into a problem:
    I'm trying to exchange my 120 GB Seagate Barracuda systemdisk with a 500 GB Barracuda and I can't install XP with SP2.
    First I tried to clone the old HD with Norton Ghost and Acronis True Image. The cloning looked fine but after taking the old HD out and moving the new one to P-ATA 1 as Primary Master I get an "error - no operating system found". I also tried a fresh install from CD. After the CD reboots the system I get the same error.
    The HD is present in BIOS with the right parameters and all is looking well - but still no go.
    I've fiddled around in BIOS (vers. 1.3) with the different settings (LBA, Large, Auto, Csh.) The last 2 options gives the "no operating system" error and the first 2 gives a "disk error" although Seagate says that I should change settings to "LBA".
    I only have the new HD in the machine. I also tried fixboot and fixmbr. I can see all the installed files when I put it in as a slave.
    So my question is:
    Does the K8N Neo2 Platinum have a problem with large hd's as system disk?
    Or is this a Seagate or Windows problem ?
    Any help is much appreciated!
    Mads

    Actually that was the first thing I did just to see if the drive worked :-) - except that I had it as master on the second ide cable. It formats like it should and all partitions report "healthy". The only difference is that the new drives c-partition is set as active (can't find a way to change it back)  - while the old one is set as system. Could this make a difference ?
    Since neither cloning nor a fresh install works I think the problem is something else. Maybe I should try Seatools and see if that makes any difference.
    Thank's all for help so far! - Other suggestions ?

  • MSI K8N Neo2 Platinum RAM problem

    My spec:
    AMD64 3000+ Venice
    1gb RAM Elixir
    1 x Maxtor 120gb IDE
    1 x Maxtor 200gb SATA
    1 x Maxtor 200gb IDE
    ATI Radeon x800 pro 256mb
    I have a K8N Neo2 Platinum motherboard, the problem is that when I try to add in another 512mb stick the system won't even boot up. I have tried other brands and amounts but still to no avail.
    I boot the system up and the monitor won't even switch on, but if I take out the 512 stick it works fine.
    Any ideas?

    Not quite.
    Use the color codes .
    If you have matched sticks in density (size) and timings (spd data) you can run dual channel.
    This means having one stick in memory channel 1 ( green ) and another in memory channel2 (purple )
    Theese are physically wired next to eachother on the motherboard , from cpu and upwards..
    You can not do that , with that mismatched modules the cpu can't initialize it's memory controller .
    So your only choice is to run two modules with single memory channel config .
    Use the colorcodes to make sure you use signgle memory channel config (since you have mismatched sticks and the A64 memory controller cant run those in dual mode)
    So your choice is to use either both green slots or both of the purple ones .
    Place the one module with the higest cas rating (slowest) in the green slot with the lowest slot number (marked on the board) .
    And the other stick on the green slot that remains .

  • MSI K8N Neo2 Platinum slows down

    Hi,
    I have a little problem with my new K8N Neo2 Platinum. I installed Windows XP and the newest nForce drivers but if I copy files over LAN (tested both LAN-Ports) or install big applications my music played with winamp slows down. It's played with half speed. In addition to that my mouse pointer is very slow. After the setup or copying files everything is how it should be again. How can I solve this problem?
    My system:
    AMD Athlon64 3500+ (Winchester)
    MSI K8N Neo2 Platinum-54G (tried different bios releases)
    1024MB Corsair XMS Twinx DDR500
    ATi Radeon 9800 Pro
    2 80GB Maxtor S-ATA (DMA Mode enabled)
    Creative Labs SoundBlaster Live! Player 5.1
    MorLipf

    Hello,
    I copy files to my bro sometimes, 5Gb - all the steam GCF files for CS/HL/CSS/HL2.
    My network usage is 80%-92%
    My CPU usage is always under 15%.
    It is worse when using 512Mb but as you have 1Gb it shouldn't be bad.
    Check in the device manager, your cd drives should be set to DMA mode.

  • K8N Neo2 Platinum Checksum Error

    Hi, I apologize if I break any rules here, but I tried to use the search option to locate an answer but couldn't find anything that helped me fully.
    My problem is that when I try to turn on my computer, I get a message saying:
    "Award Bootblock BIOS v1.0
    Copyright 2000 Award Software Inc.
    BIOS ROM checksum error
    Keyboard error or no keyboard present.
    Detecting floppy drive A media
    INSERT SYSTEM DISK AND PRESS ENTER".
    Except this, my computer is completely "dead", I cannot go anywhere. From what I have understood, my BIOS is corrupted, and I need to flash it. This should be done by inserting a boot floppy with added AWDFLASH.exe and a bios.bin. The thing is, I don't know how to find these files, or at least the correct ones. I have also tried to google for a solution, but haven't found anything satisfactionary. So this is kind of my last resort. I am very sorry if this is a newbie question, but I have almost no experience in this advanced (from my perspective) knowledge.
    If someone could help me locate the correct verisons of the Award Flash utility and BIOS file, and write a short step by step-walkthrough of how to proceed, you would have my eternal gratitude.
    My system is a 4 years old:
    MSI K8N Neo2 Platinum 54G S939 with nForce 3 Ultra
    Windows XP Home
    AMD Athlon 64 3500+ 2.2 Ghz
    Gainward GeForce 7800 GS 512 Mb
    2x TwinMos 512 Mb RAM PC3200
    Maxtor Diamondmax 200 Gb SATA
    MS-7025 Ver: 1 is printed on the motherboard.

    Quote from: go_for on 11-March-09, 03:04:25
    This one is stuck in Award bootblock mode, will most likely need a re-flash from a bootable floppy disk.
    Make a bootable floppy disk, in e.g WinXP.
    Make a file with notepad, containing this line:
    AWFL833D.EXE W7025NMS.1D0 /CC /CD /CP /QI /R /PY /SN
    Save this file on this floppy by the name Autoexec.bat
    Also add the two files AWFL833D.EXE and W7025NMS.1D0 on this floppy.
    Power up the K8N Neo2 Plat. with this disk in the floppy drive. The flashing will begin, let it finish.
    Remove floppy and reboot. If it  succeeded, set all relevant values in BIOS and save&exit.
    Quote
    This one is stuck in Award bootblock mode, will most likely need a re-flash from a bootable floppy disk.
    Not always, the same fake error message can came from bad memory stick too.
    Also he didn't flash his BIOS before the message to appear.

  • New CPU, Msi K8n neo2 platinum - no boot!

    Greetings!
    I got the following components:
    *MSI K8N NEO2 Platinum -54g MB
    *4 x 512mb Geil Value Ram
    *Gainward 7800GS+ Bliss 512mb AGP
    *Samsung Spinpoint 500gb SATA HD
    *Corsair 620HX (620W) PSU
    *CPU AMD Opteron 180 Dual Core (upgrade from AMD 3000+ Winchester)
    I recently upgraded my PC with a new HD, more ram, new CU Fan/heatsink - on an AMD 3000+ (Winchester). PC wouldn't boot - I did however manage to fix it. I think it was because of the ram, one of the bricks had some dust on it. Since then, my pc has worked 100%...
    Today, however, I got a new PSU and CPU in the mail! A Corsair 620W PSU and an AMD OPTERON 180 Dual. I carefully cleaned the surface on the heatsink etc, and applied an appropriate amount of "Arctic Alumina" on the CPU/heatsink (as followed per instructions from Arctic). When I have connected everything, and fire my pc up - it just won't boot.. (The monitor won't light up).
    Since then, I have carefully checked all wires, unplugged/replugged etc.
    But it just won't boot!
    I do have the latest bios (1.0D), so it should support my CPU.
    I should mention some "weird" things, though. When I try to boot up, everything seems normal (All fans are running), but there are no lights on my case! And I can't turn off the PC while holding down the "power" button on my case. I can't reset either.. as soon as I turn the PC on (by turning on the PSU power switch), the PC starts running. Normally I would have to push the button on my case. ALSO: I have cleared CMOS, still a black screen. And I have tried 2 different monitors, so I know it aint that either.
    My old PSU was a Chieftec 360W one (and my case is a Chieftec also). The old PSU was connected to "SFAN2" on my MB,.. my new PSU isn't connected to any "SFAN" at all.. I doubt that has anything to do with the problem though?
    Any suggestions on what I might do ?
    Edit: D-bracket shows this (Yellow, red, red, yellow):
    BIOS Sign On
    - This will start showing information about logo, processor brand name, etc... - It stops here. No boot screen

    Quote from: BOSSKILLER on 14-November-07, 21:14:42
    remove power cord from the PSU(else will not work) and Clear CMOS Guide.
    leave one memory stick only in a 1st DIMM slot near to CPU socket and try to boot.
    Done & done.
    Still no boot screen :(

  • The build in firewall in MSI K8N Neo2 Platinum

    Hello everyone,
    I am using an MSI K8N Neo2 Platinum-54G nForce3. I wonder if anyone else is using the built in firewall? I have some problems with my Internet connection and I think it is firewall related.
    I would like to know if anyone else has any valuable feedback on this subject.
    Thank you!

    Works fine for me, make sure you have the latest drivers installed and turn off any other firewall including the Windows one. You will find that you may have to set up some rules to open up ports for some apps. I have set mine up to play Farcry and now get no Punkbuster problems.
    I am using the Nvidia ethernet to connect toe the internet and the Realtek to network my second PC.

  • MSI K8N Neo2 Platinum PCB 1.0 vs 1.2

    I noticed someone has a PCB rev 1.2 of MSI K8N Neo2 Platinum 54G. Does anyone know what they have changed in the new revision? I got a PCB 1.0.

    Dunno but I really hate to hear that a newer revision chipset/mainboard is availaible after I make a purchase.
    Theres 2 typical scenarios regarding newer mobo revisions:-
    1. The rectification of bugs and problems.
    2. The same results can be achieved with fewer components driving down costs.
    Hope it's the later  

  • Kingston HyperX Memory & K8N Neo2 Platinum

    Hello.
    I have a MSI K8N Neo2 Platinum board (BIOS 1.3) with AMD 64 3000+ 939 CPU.
    I am trying to run this with 2 Kingston HyperX PC3200 512MB memory (KHX3200ULK2/1G).  This is the latest "Ultra-low Latency" memory from Kingston.
    When I run this memory with NO overclocking at 2-2-2-5-1 at 2.7 volts (standard setting for this memory) with a single module, I get NO errors.  When I try both chips in dual-channel mode, I get errors (on MemTest86).
    (I also get errors if I run this memory on "Auto" setting in BIOS)
    I CAN run 2 sticks of Crucial PC3200 512MB (regular, not Ballistix)  at standard settings in dual-channel with no errors.
    Has anyone got this memory to work on this board in dual-channel mode?  If so, how? At what timings?
    Any help would be greatly appreciated.

    Quote
    Originally posted by Xak
    Quote
    Originally posted by GlennVidia
    In the meantime...
    Try loosening up the memory timings first, start with 2-2-2-8 thru 2-2-2-11
    Then if no luck try 2-3-2-6 thru 10 or 11 you may even have to resort to 2.5 3-3-X
    You should be able to at least find a sweeter spot.
    You may even have to go to 2T and non aggressive settings.
    Why would the timings work when in single channel mode, but not in dual channel, when the Crucial memory works fine in dual channel at the same timings used in single channel?
    On a side note, the Kingston pair was purchased together in a matched set, while the 2 Crucial sticks (actually the memory from my system) were bought seperately over a month apart.
    The timings that RZT tried are the exact ones Kingston specifies for that model, there should be NO reason whatsoever they wouldn't work at those timings, dual or single channel.
    Please correct me if I am wrong...
    First of all, I said "in the meantime," meaning until someone else came up with a better answer. If I have problems with memory, regardless of what the manufacturer says' I hunt for a sweetspot (if there is one).
    Quote
    Why would the timings work when in single channel mode, but not in dual channel, when the Crucial memory works fine in dual channel at the same timings used in single channel?
    That's like trying to compare apples to oranges. Two different manufacturers and likely different chips onboard, not to mention likely different PCB design.
    What I suspect is either one stick is further out of spec than the other and they are not a properly matched pair. Kingston has a history with the nForce chipset which leaves little to be desired.
    That is why you might see very similar systems, and one works with the same ram, and the other doesn't. It's called parametric differences. In short, one stick my be at the upper end of the spec and the other stick may be at the lower end. Then, throw in the motherboard, and the CPU, (now with the onboard memory controller) while we're at it, and you have a real touchy situation. There is little room for lower quality. That is why matched pairs exist. Doesn't mean it's mandatory, however.
    Quote
    On a side note, the Kingston pair was purchased together in a matched set, while the 2 Crucial sticks (actually the memory from my system) were bought seperately over a month apart.
    I take it you know this person, otherwise this is not making sense or you are a pretty slick hijacker
    Matched set can still be flawed, I get em from the best once in a while. It may not be the RAM at all. Only way to tell for sure is to try it on another identical system or try another pair that passes muster in another identical system. All this speculating is useless unless you've exhausted all possibilities.
    Quote
    The timings that RZT tried are the exact ones Kingston specifies for that model, there should be NO reason whatsoever they wouldn't work at those timings, dual or single channel.
    Please correct me if I am wrong...
    Not wrong, maybe a little overoptimistic. Some situations warrant different measures. It's not that black and white, nor is it written in stone. At this point it only indicates there is indeed a problem, where it lies, would be better off using a dartboard to guess at this point.

  • Want comments on k8n neo2 platinum prior to buying it,

    hi people.
    im doing some research prior to buyng an amd64 motherboard and have been looking at this one.
    MSI K8N NEO2 Platinum-54G Moderkort S939 nForce3 250Ultra,SATA,GbLAN,ATX,Dual-DDR
    is the firewall good or bad ?
    is the motherboard easy to work with ?
    stable ?
    anyone tried the new 3000+ and 3200+ on it ?
    i would also want end user comments on it.
    Good Night.
    EDIT:
    im going to most of the hardware found in my signature.
    if the psu aint up to it i will use a second psu until i get money to buy a bigger one.

    Hi Raven, missed this thread till now!!  Congrats soon getting S-939 A64, that will be way less than 10lb shipping charge to mail you  
    My MSI K8N Neo2 NF3 250 Ultra has been stable from BIOS v1.0 upwards, no mis-fires, no overheats, no comm/USB/PS2 probs, smooth all the way, for me. Per reviews Gigabyte and Asus also good, MSI won Bmarks on reviewers reference boards.
    Peeps reporting probs with board here though, so check out this nVidia section. The BIOS updates helped some.
    -Zalman CNPS7000_ Al/Cu HSF screws right into the original backplate, keeps my FX53 at 34C Folding.
    -CNPS7000A or B are good, peeps say ya' need to use the backplate came with the HSF. The mobo backplate comes off pretty easy. Edit: re Hansh's mod Zalmans.
    -The stock AMD fan is fine at stock or low OC.
    -No HSF install pix I've seen, even the monster TT heatpipe cooler, have interfered with RAM, but there's always an exception.
    -Your Antec is prolly good enough, AMD rec's a reputable 350W or better. CPU uses ~90W (98?) Like ya say, if it isn't you always have the other one too
    -NB fan is small but works well so far. It's noise doesn't compete with the other 8 fans
    ps: Software only prob, Win XP doesn't like RAID 5 PCI cards at install.
    =--
    Hansh, Allreet!    

  • K8n Neo2 OCZ Memory Detection Problem

    1.Product Type: K8n Neo2 Platinum
    2.BIOS version: 1.D
    3.External VGA Type: Radeon x1950 Pro
    4.CPU Type: Athlon 64 3200
    5.Memory Type: OCZ4001024ELDCPE-K 2 x 512MB
    6.Power Supply Type: EnnermaxNoiseTakerII 485w
    7.Operating System: XP/Vista Dual Boot
    8.Problem Description:
    I have just acquired the memory speciified above, but the system will not POST with this RAM fitted on the mainboard.
    The RAM above is certified to run with my mainboard (K8n Neo2).
    I have other RAM from OCZ which works fine.
    This RAM is:
    1 x 512MB OCZ400512ELPE
    1 X 512MB OCZ400512EL
    I have spoken to OCZ support and done the following:
    Reset the CMOS
    Increased voltage for the DRAM
    Tried each of the new 512MB DIMMs individually.
    But this has not helped and OCZ have no more suggestions other than to ensure that I have the latest BIOS, Which I think Id do.
    Any help is appreciated.
    Thanks

    hi there,
    what is your RAM which you are trying to run? is it OCZ4001024ELDCPE-K 2 x 512MB matched pair?
    ensure you have used mainboard DIMM slots: DIMM1 & DIMM2
    where DIMM1 is the 1st DIMM slot close to CPU socket.
    have you tested each of memory sticks individually using DIMM1 slot? if yes what are the results?
    remove power cord from the PSU and Clear CMOS
    re-try to boot.
    you can setup memory vcore manually from BIOS to 2.75V and Command Rate to T2 (all memory timings leave it to Auto) and re-test.
    get a copy of Memtest86 and ensure no errors will comes during testing.

  • Cool and Quiet problem on K8N Neo2 Platinum v1.3 bios

    Hello
    I have a problem with the Cool and Quiet feature on the K8N Neo2 Platinum (v1.3 bios).
    As soon and I boot the Core Center v1.7.0.0 will instantly overclock my A64 3500+ CPU to 3000+ Mhz.  Of course this reboots my PC.
    I have Cool and Quiet enabled in the bios, Automatic overclocking disabled in the bios and the Core Center softwares overclocking is (well it was) disabled?  How can I install it or get it to stop overclocking the system.
    I want to run the Core Center to enable the Cool and Quiet fan controlling stuff.
    Thanks

    Strange that Corecenter would overclock your cpu to 3ghz. It's known to be unreliable software, but not that unreliable.
    Are you running a stock 3500+, or are you overclocking the HTT/FSB beyond 200?
    Previous posted was right about cool and quiet software. You don't need corecenter to run it. Just stay away from corecenter and even uninstall it
    Cool and quiet software (a device driver that you download from AMD, or that comes pre-installed with XP SP2) simply works as follows. It introduces the notion of several p-states (processor states) that it switches between based on its reading of cpu load. A p-state is a pairing of cpu voltage and cpu multiplier.  On my 3200+ newcastle, the p-states are:
    1.5V, 11x
    1.4V, 10x
    1.3V, 9x
    1.1V, 5x
    Your 3500+ might be similar. Anyway, just run cpu-z instead of corecenter to watch your cpu speed changing on the fly.
    As far as fan speeds go: the cool and quiet driver doesn't affect fan speeds.  That means to get the "quiet" part of "cool and quiet" you need either
    (a) a fan that has a temperature sensor and which automatically changes its speed based on that, or
    (b) just use the motherboard BIOS setting to do the same via bios software.
    (c) use speedfan to do the same via windows software.
    I myself prefer (b) but it depends on the bios accurately reporting temperature, which can vary wildly between bios releases (e.g. newcastles didn't start getting accurate temp reports until bios 1.4).

  • Problem on boot MSI K8N Neo2 Platinum

    I am an italian lover of MSI motherboards.
    After I bought a MSI KT3 Ultra Aru, then MSI K7N2 Delta ILSR and now I have a K8N Neo2 Platinum.
    My hardware are:
    MSI K8N Neo2 Platinum
    Athlon 64 3200 Winchester
    Corsair XMS 1024 TWINX 3200 PLL
    Maxtor Diamond Plus 9 80 Gb
    Asus Radeon 9600XT.
    The problem is that at the power on the bios don't start. The LED on D-Bracket are three green and one red. On the manual this error are written:
    Inizializing Video Interface
    This will start detecting CPU clock, checking type of video onboard. Then, detect and initialize the video adapter.
    This problem is frequent for my motherboard. However not always.
    I attend your answer for this problem.
    Thank you for all and for my english school.

    Hi Italiano,
    Welcome to the forum.
    Have you details of your power supply. please show Maximum 3.3v,5v & 12v.
    These are usually on the side of the power unit.
    try:-
    1) Enter bios Cell Menu - HT change from 5 ---> 4 using +/- keys. Save & exit.
    If it still doesn't boot try:-
    2) Re-inserting your Asus Radeon 9600XT. Sometimes they don't go in correctly.
    3) See if you can boot with just 1 memory module in slot 1.
    Luck

  • K8N-Neo2 Platinum pauses for 25 sec at boot, nvatabus.sys the problem?

    All,
    After POSTing normally and starting to load Windows XP, my system halts at the Windows XP splash screen for about 25 seconds. Nothing happens, no disk activity or anything, the system just sits there.
    I used Microsoft's Bootvis utility to see what was happening. It turns out that the nvatabus.sys driver consumes 100% CPU at boot for 25 seconds then the system continues to boot normally. Does anyone else see anything like this?
    I am running the latest nForce drivers from MSI. The driver in question:
    NVIDIA nForce3 Serial ATA Controller 2.6
    Driver Date 6/3/2004
    c:\WINDOWS\System32\DRIVERS\nvatabus.sys 5.10.2600.0446
    Windows XP SP1
    I have a RAID1 of two 160 GB SATA drives. The mirror is healthy and working fine.
    After booting the system is rock-solid stable, no problems there. It's just this unexplained pause at boot. Does anyone have any ideas how to fix this?

    ok check it out guy's this thing drove me insane all night last night and most of today. I was ready to return everything and give up. But alas all is not lost. Here is the rundown on what i just did.
    My Equipment:
    Athlon 64 3800+(w/ stock fan)
    MSI K8N Neo2 Platinum Socket 939
    2X512 Corsair TWINX1024-3200XLPRO ( with the cool led's )
    2 SATA HD (1 Maxtor Diamond10 300 GB w/ 16mb cache, 1 Segate 160GB w/8mb cache)
    PP&C 425 ATX Deluxe
    Radeon 9700 Pro ( cat 4.8 )
    Audigy2 ZS
    Sony Floppy
    Sony 8x52x52x32 DVD Rewrite
    I have been reading and reading just like all you guy's. On a few websites i would pick up bits and pieces on what to try. Heres what i did. Upon Boot up i entered the bios. I then went to Cell Soft and adjusted my timings for my memory. I was at 2.5 not 2.75. I then set my speed down to 166. Exited and restarted. Big mistake everything ri=uns terrible slow and my expensive DDR 400 memory was showing up correctly at 333. Rebooted again entered the bios. reset my speed to 400. Then set the Overclock feature to manual. Set my timings at 2,2,5,2 200 and 2.75 volts. After saving settings and exiting I then turned off the computer. As per some other suggestions I moved my Audigy2 to the bottom most pci slot the one above the orange slot. I moved my memory to slots 2 and 4. I moved my SATA to slots 3 and 4. I rebooted went into the bios again and setup all my voltages. CPU was Auto, AGP was max yellow setting. Memory still at 2.75. I disabled the onboard serial and parrallel ports. Rebooted
    Fearing the worst,
    5 seconds, 10 seconds, windows screen loging prompt. There was nothing wrong at all. It rebooted effortlessly. It re found my Audigy card and wanted driver but that was it. I am going to reboot a few more times and then run sisandra to test. I hope some of this will help you. I post in a few after some of those reboots.

Maybe you are looking for

  • Group Policy Client service failed! Help!

    A few days ago I was booted out of my account, while watching a DVD. My system restarted itself, but not before flashing some sort of blue screen. Unfortunately I was unable to read the content of it. After restarting, I was presented with a light bl

  • HT204247 How much storage space do I have in my iCloud email?

    HHow much storage does my icloud email have? For example when I used gmail to send pictures it holds 17GB. So if I send pictures through my ICloud email how much storage does it have? Is the storage on my iPad?

  • When is the iphone 5 being released?

    When is it getting released in Australia?

  • Mi iphone shut off with battery at 100%

    mi iphone shut off with battery at 100%

  • BAPI to XML

    Hi all, Could someone help me to generate the BAPI into a XML structure. I could do it with Idoc's using transaction we60 where i can convert the documentation into an XML structure. I would like to do the same thing for the BAPI.ls it possible. Than