K8N NEO2 Platinum Dead once again

This is my second K8N NEO2 that dies!!!! What is going on at MSI I mean what are the odds? Both boards have worked fine in about 3 days but for some reason just died on the fourth day.
I RMA the first one and talked with the store where I bought it and they said the board was totally dead so they sended me a new one. Now this one died so I will send this one back and take my money back. Is there anyone that have experienced this problem?
BTW my PSU is an Antec TruePower 430W and yes I know that it has a weak 12V line but what kind of board needs more than 20A? And if the PSU is to weak as some say, how can the board be killed by the PSU? I have also tested the PSU and it's nothing wrong with it.

crar,
The short answers to your questions are no and no . The reason being that the board flexs all the time while it is in the case. It also heats up and expands unevenly causing uneven flexing. It might just be that the metal piece hasn't hit the right spot to cause a short and that over several days the odds are much higher that it will. You may never have noticed on your previouos board because there may not have been anything shortable near the metal piece.
A UPS is fairly effective at blocking AC line transients. It is a good idea to have one regardless of whether the power in your area is poor or not, but a necessity if it is.
RB

Similar Messages

K8N Neo2 Platinum = Dead Board?

I hope that you folks could help me. I have built about 100 computers between personal and professional lives.
This unit is about to hit a wall at warp speed or will be RMA'ed, or you can help me find out what I am doing wrong.
Check my sig for my specs. I can't install windows xp on this unit. It almost always locks up when I am down to 3 to 9 minutes remaining in "saving settings" I did get it to install once but it locked up while installing SP1 and then it would not boot again. Repair install failed as well. Could not even get into safe mode. Last good configuration does not work either.
I have tried swapping power supplies to no avail Seems like a poorly designed product if it is that finicky with standard power supplies. Newegg won't return it. Finally hunted down a tech support number for MSI and the techs could not understand english. anyone got a number for english speaking tech support?
I have tried installing windows on this close to 20 times and cannot get it going. I have tried various settings for memory and cpu and tried even the lowest settings. and event had to reset cmos more that once. Shesh. I should have gone with an EPOX! Could someone please prove me wrong about this board?

Thanks Shanks,
But its D E A D. Fans (including CPU) come on for 2 seconds, then shut off. You have to unplug the power to even attempt again. Went out and bought MADDOG 500W PSU ($99 USD) with 30A on +12V Rail and same results.
Unplugged all drives. Same Result.
Remove All Cards. Same Result.
Removed board, Checked for Shorts or incorrect standoffs, Same Result.
Reset CMOS, Put MB with only CPU and Ram on piece of cardboard, Same Result.
MB by itself, stripped naked on cardboard with just PSU in 20 pin and 4 pin, Same Result.
Its Dead Jim! Its officially a dud. 10 hours of work on this. The most out of over 100 computers/servers built.
This bested an A+ Computer tech/Systems Engineer know for resurrecting "Dead" systems.
The originally PSU (Antec 400) is still working, actually powering my old EPOX 8rda+/Barton 2500 so that I can write this posting.
I'm suspecting Dendrite growth in the board causing a short or an NG component. Actually while looking at the bottom of the PCB, I' noticing that the Masking is matted as if it a lot of masking was put on by a roller and not from the original process.
This may have been a repaired PCB in the first place.
Newegg states that the this board is warranted by the manufacturer only. They got their $149
Posted review on this board regarding the +12V rail issues and reminding potential buyers about Newegg's "Warranted by Manufacturer only" and gave it 2 stars. Lets see if NewEgg will post it.
Thanks for you help, gonna RMA this before I am tempted to test its aerodynamic qualities as a "frisbee"
Mjrhzrd - "Major Hazard"

K8N Neo2 Platinum dead??

I just built my new computer a few days ago, and had been struggling with video card problems. Not 5 minutes after I finally get everythihng fixed (bios setting problem), I was playing farcry, and the computer just drops. I try powering it back on, and nothing. The fans kick on for about 1/2 second, and they are off again. Not even enough for the D-link to tell me what is wrong.
So, I try unplugging it and plugging it back in. Nothing, same problem. I reset the BIOS, same problem. Disconnect everything except the CPU (RAM, HD's, vid card, etc), same problem.
The kicker is when I remove my CPU, the motherboard starts up fine (fans comes on, all seems happy, short of the missing CPU). If I reinstall the CPU, everything is essentially dead again.
This is REALLY annoying, considering the time I spent trying to get the vid card working. Anyone have any thoughts?
Thanks!
AMD64 3800
K8Neo2 Platinum
1Gig Corsair
WD74Gig Raptor
BFG 6800 Ultra

PSU is a 550W coolmax. I know it isn't the PSU because I tried different PSU's and got the same result (I forgot to mention that).
As far as overclocking, I wasn't. I turned all of that off (that was part of what was causing problems with my video card).

Msi k8n neo2 platinum dead

Hi all,
i have a problem with my board !
is almost new i use it only 2 months and suddenly no boot,nothing;
after checking i observed that near the cmos bat. the PB5350 transistor is burned;
i'm not the only one user who had this problem;checked on many forums and the same problem appeard for a lot of user
my question is if i sens back the board will MSI repair it or change it?
thanks

Quote from: Kaveman on 24-August-06, 12:27:13
I also have the same board I installed an athlon 64 x2 4600 updated bios to 1.C ran the hotfix , new drivers for the x2 . Runs stable when benchmarking but shuts down when intensive cpu load is used like BF2 gaming or burning dvd/cd's , any ideas ?
Maybe that your RAM is the problem as you've the mixed RAM and also their timing and the volt are also different. Tried to boot with those same timing and latency as well as the Volt. have you tried to run Prime 95 for the CPU benchmarking? Does it stabile? Gd luck.

K8N Neo2 Platinum is dead?!?

Hi all!
I've got a problem with my computer. After sending it to Standby, it wouldn't start again. AT ALL! There is nothing happening when I press the power button, even after disconnecting the power. Just the Power-LED is on, everything else stays quiet. No fans, no harddrives, no beeps...
I already tried another power supply, didn't help. I also unmounted everything from my mobo except the CPU, but still no result. It just won't do anything. ??? If it would at least tell my something with some error codes from the speaker or the D-Bracket...
Has somebody got any clue what is happening?
System:
K8N Neo2 Platinum
A64 3200+ Venice E6
4x512 MB Corsair VS
ATI R9800 Pro
I would really appreciate help!
Greetings,
Kristofer

Quote from: Schwede on 20-May-06, 17:38:49
Well, I'm gonna. Doesn't leave me much choice, but first I will test my CPU on someone elses board.
Nice illustration
Since I have to swap my mobo, I will upgrade to an nForce4 anyway and get a new graphics card (actually I ordered already ).
Then I have to get a new PSU anyway.
However since I cannot do this within the next 3 weeks, I am still trying to get my system running.
Well, if you have a mobo to try the CPU in, great, that's a good way to rule that out. If I had that option available, I would lean towards just swapping out the board since I am already going to have both machines basically torn apart. I usually don't swap CPU's without taking the whole board out of the case and POST testing it before mounting. I think that would tell me more than just taking my CPU out and putting it in another machine...but that's me.
The 939 & 754 sockets are much easier to deal with as opposed to the Socket A when the board is still mounted. I've seen bad things happen by not having the right angles and room to work in...
It all really depends on your scenario and what's available to you. Sometimes we are limited in our options since we don't have an inventory as enthusiasts opposed to a system builder. Not to mention the hassle of bringing your gear somewhere or having a friend bringing theirs to you.
Just remember if you are using a different chipset, not to let it try and boot to the OS. Really, all you need to do is see if will POST.
That metaphor is my favorite and gets the point across rather well

News - BIG PROBLEM - MSI K8N Neo2 Platinum - DOES NOT POWER!!!

Hi to everyone.
I'm a proudly owner of a MSI K8N Neo2 Platinum that in one year gave me no problem until yesterday morning.
I used the computer in the night before and when I finished I turned it off and I went to bed.
Yesterday morning I found the power led blinking (like if the system was in standby), and there was no way to turn the PC on.
I even took off the battery for more than 12 hours and I left only minimal components installed:
the video card (Gainward GeForce 6800),
the psu (Antec TruePower 550W),
1 x 512 MB Ram Crucial Ballistix,
and I checked them into another computer and they work perfectly.
I tried shorting the MB power switch pins with a screwdriver and I've even tried to power on the system without the Memory or the Video Card... I've tried everything that came across my mind with no efforts!!!!
Every time I give power to the MB appens only that the power led starts blinking, but pressing the button the PC doesn't turn on.
PLEASE HELP ME... I really don't know what else to do!!!
Thanks,
Alberto

Quote from: alberto_melita on 20-August-05, 20:14:56
Hi thanks for the answers.
I do have a D-Bracket, but my problem is not that the system does not boot or does not post... my system DOES NOT POWER ON (!!!!), so d-bracket is useless!
When I plug the system power the only thing that happens is that the power led starts blinking (with the system still in soft-off), and if I press the power switch button nothing happens!
I've the bios for 7025 v1.8 and the settings where for OFF on power-loss ond pressing the button (can't rememeber if it was more than 4 sec) was meant to turn off the computer, but considering that I un-powered the pc more than once without the MB battery the settings should be factory default by now.
I went through the Windows-XP shut-down system, and i could not be an electrical problem as I always used the PC with a pretty good UPS unit.
Right now these are the full specs of my sytem:
- MB MSI K8N Neo2 Platinum nForce3 Ultra
- GAINWARD 6800 2600 GLH 256 MB Ram
- PSU Antec TruPower 550 W
- CPU AMD64 3500+ core Winchester @11*210 Mhz (this cpu has never overclocked very well)
- HEATSINK Thermalright XP-90 with a 12 Cm Enermax Fan (CPU temp in always below 55 °C when stressed)
- 1 x 512 Mb RAM Crucial Ballistix DDR400 optimized for MSI K8N Neo2 Platinum
I left only these things inside my computer in the hope that it would turn on... it did not work. I tested each component but the MB, and they work perfectly.
Again...
Thanks for you efforts, any help will be appreciated.
Alberto.
All parts have been tested: CPU/RAM/GFX/PSU/HD/DVD, just not the MOBO ?
Checked if the MOBO is shorting in the case ?
Have you tried using the reset switch as power, on/off switch ? I've seen before when the power switch stops working (lose/bad wire busted spring) after swapping reset to power, then the system turned on. Worth a try, as sending it back to USA won't be cheap. If its over 1 year old it mite not be covered by the re-seller and or MSI. Best to check this out as law and warranty is different from country to country.
Good Luck

New K8N Neo2 Platinum, AMD 64 3500+ sytem freezing

I have posted to a couple of forums and still can't get this problem resolved, hope you guys can help.
I put together a new system last Friday night and spent all weekend trying to fix it. I ended up with 2 bad power supplies, one fresh from the store was dead, but got that resolved. Got the system up and running, got online, surfing and FREEZE..everything stopped. Rebooted, 5 minutes later, same thing, over and over again.
Tried checking memory, it's fine, both sticks, power supply is fine, everything seems to be running fine except it keeps freezing after about 5 minutes.
I wonder if it's a bad board, so I tried to RMA it with the vendor and they want me to try outside the case to see if it won't freeze there, haven't had the time yet cause I'm working, will try that tonight.
Also, one guy on a different board suggested that I try a fresh install of windows xp as the old drivers might be interfering with the new drivers. I will try that tonight also.
If anyone can give me any other suggestions, I would appreciate it. If I can't get this resolved, I'm going to send back the board for a new one.
Below are my specs:
AMD 64 3500+
MSI K8N Neo2 Platinum mobo
2 x 512 Kingston ddr400 (pc3200)
antec true power 480
wd 120gb hd, wd 80gb hd
cdrw generic, dvdrw generic
bfg 6800 oc video card
thanks

Thank you both for your posts, they are both informative and I will be using your information Friday night. I'm just so tired after work, I don't want to get part way into it and have to leave it for the next day, I have to get up at 3am everyday and get home around 6-7pm and I'm beat!
So, Friday after work, I'm going to start with just the basics and go from there, using all the information I've been getting from this board and a couple of others. Seems like the best thing to do is, start with barebones, reset cmos, reset battery and install fresh windows os.
I will post Friday after I start and hopfully I will get this problem fixed.
thanks again

K8N NEO2 Platinum rebooting

Hi all,just got myself a 64bit MSI K8N NEO2 Platinum board & a 3200+,am happy with it but a couple of days ago i got a blue screen with a long message that i didnt have time to read before the pc rebooted,after the reboot i checked the event viewer log file in administrative tools/control panel but couldnt narrow it down as my particular error code wasnt among the possible causes.
Among some of the possible causes were incorrectly installed USB drivers or the BIOS,i downloaded the latest BIOS update before this problem started(V1.40) which i am using now,i used the MSI live update software to flash it which i did in windows mode.Sorry for prattling on!well it did it again tonight and i managed to read a bit of the writing on the blue screen which mentioned flashing the bios to the latest version.I was wondering if anyone else is having the same problem and if so could you please advise me? Thanks for your patience and any help Heres my sys specs:
Model: AMD Athlon(tm) 64 Processor 3200+
Speed: 2.01GHz
Model Number: 3200 (estimated)
Performance Rating: PR3015 (estimated)
Type: Standard
L2 On-board Cache: 512kB ECC Synchronous Write-Back (16-way, 64
byte line size)
Bus(es): ISA AGP PCI USB FireWire/1394
MP Support: 1 CPU(s)
MP APIC: No
System BIOS: Phoenix Technologies, LTD 6.00 PG
Mainboard: MS-7025
Total Memory: 1023MB DDR-SDRAM
Model: Micro-Star International Co Ltd (MSI) ???
(00E1)
Front Side Bus Speed: 1x 201MHz (201MHz data rate)
Model: Advanced Micro Devices (AMD) Athlon 64 /
Opteron HyperTransport Technology
Configuration
Front Side Bus Speed: 1x 201MHz (201MHz data rate)
Total Memory: 2048MB DDR-SDRAM
Memory Bus Speed: 2x 201MHz (402MHz data rate)
Monitor/Panel: CTX EX950F series
Adapter: RADEON X800 Series
Adapter: RADEON X800 Series Secondary
Removable Drive: Floppy disk drive
Hard Disk: Maxtor 6Y080L0
CD-ROM/DVD: HL-DT-ST DVDRAM GSA-4081B (CD 32X Rd, 24X Wr)
(DVD 4X Rd, 3X Wr)
CD-ROM/DVD: MSI CD-RW CR52 (CD 40X Rd, 52X Wr)
CD-ROM/DVD: AXV CD/DVD-ROM SCSI CdRom Device (CD 32X Rd)
(DVD 4X Rd)
1.44MB 3.5" (A:): N/A
Hard drive (C:): 76.3GB (51.9GB, 68% Free) (NTFS)
CD-ROM/DVD (D:): N/A
CD-ROM/DVD (E:): N/A
CD-ROM/DVD (F:): N/A
Serial/Parallel Port(s): 1 COM / 1 LPT
USB Controller/Hub: Standard OpenHCD USB Host Controller
USB Controller/Hub: Standard OpenHCD USB Host Controller
USB Controller/Hub: Standard Enhanced PCI to USB Host Controller
USB Controller/Hub: USB Root Hub
USB Controller/Hub: USB Root Hub
USB Controller/Hub: USB Root Hub
FireWire/1394 Controller/Hub: VIA OHCI Compliant IEEE 1394 Host Controller
Keyboard: Standard 101/102-Key or Microsoft Natural PS/
2 Keyboard
Mouse: PS/2 Compatible Mouse
Device: Creative SB Live! series
Device: Creative Game Port
Model: EPSON Stylus CX3200
Windows System: Microsoft Windows XP/2002 Home (Win32 x86)
5.01.2600 (Service Pack 2)
Network Drivers Enabled: Yes
Warning 100: Large memory sizes should be made of
Registered/Buffered memory.
Tip 101: Large memory sizes should be made of ECC/
Parity memory.
>
>
Device Type: VGA Video Adapter
Device ID: bus 1, device 0, function 0
Windows Device Name: RADEON X800 Series
OEM Device Name: ATI Technologies ??? (4A49)
OEM Hardware ID: FUN_0, VEN_1002, DEV_4A49, REV_00
Device Name: PC Partner Ltd ??? (4A49)
Product ID: VEN_174B, DEV_0D42
Revision: A / 1 (0)
Version: 3.00
Command Queue Length: 256
Fast-Writes Support: Yes
Over 4GB Addressing Support: No
Isochronous Mode Support: No
Addressing Support: 32-bit
Data Transfer Modes Support: 4x 8x

My K8N Neo Platinum [754] did not include a NB fan. But this usually means the overall size of the heatsink is larger. If you remove the fan from yours, the size of the heatsink will not be big enough to cool your NB. As for temps, I've never seen my NB get hotter than 45'C. Note that the core on my NB should be slightly different than yours.
You could try to use the BIOS fan control for the NB. If set correctly, it should reduce some noise.

SATA HDD installation on K8N Neo2 Platinum, Non-RAID, Non-Bootable

Hi-
I’m a rank newbie on this forum (first post). I have a K8N Neo2 Platinum Mobo, which I’ve recently gotten up and running, with Windows XP-Pro SP2 installed on a single IDE drive. I would now like to add 2 SATA drives. I don’t need or want the SATA drives to operate in a RAID array, nor do I want them to be bootable. I want to use them independently for data storage. I read the following thread (I am posting here on a separate thread per the author’s wishes not to get his original thread too junked-up) :
Single SATA or Multiple Drive Array Setup FAQ
I have not yet plugged-in either of my SATA drives, because I don’t want to risk corrupting my existing boot (IDE) drive. I just had a few questions about the procedure given in the referenced thread, in the Single Drive Setup:
- Step 14 States: “Make sure the “RAID Mode” is Stripping and Striping Block at 64k or Optimal. Hit F7 (Finish)”. Is this correct for a single non-boot drive?
- Step 22 States: “As most of you know when you enter the Setup for Win2k/WinXP you will need to hit F6 to load additional drivers for other SCSI devices.” I assume this means I need to boot from the Windows CD. Is this true even if I already have Windows installed on an IDE HDD on this system? At what point will I need to hit <F6> ? Will I be prompted to do so?
- I have downloaded (from the MSI website) the NVIDIA RAID CLASS DRIVER & NVIDIA Nforce Storage Controller (20 files, 1.3 MB total). Should I put these on a floppy? Or can I access them from a directory on my OS HDD?
- Should I go ahead and plug-in both of the 2 SATA drives I want to add to the system before beginning the driver installation? The only reason I would consider installing them one at a time is if it eliminated any confusion between RAID vs. independent (I want independent operation). If I do install them one at a time, do I have to install the driver twice?
Any help would be appreciated.
- the bbdude

OK Thanks JeanGuy and ssjkakaroto,
I have connected both of my SATA drives. They are enabled in BIOS but not set to RAID. I booted up to Windows on my IDE drive. In Disk Manager, the display shows Disk 0 (C: System), Disk 1 and Disk 2 as uninitialized, and my DVD (D:) drive. At this point, I could probably go ahead and run the Initialize and Convert Disk Wizard to get these disks formatted and be dome with ot now. Before I do that though, I just have a couple of more questions.
- I had already loaded the nVidia nForce3 system driver prior to installing the SATA drives, but I went ahead and did that again after installing the SATA drives and restarting Windows. I used Live Update, which went out to the MSI site and found version 5.03 of the nVidia nForce3 system driver. I'm not sure how to find the "Nvidia 5.10 driver package which include the latest SATA driver", ssjkakaroto referred-to. The Live Update install procedure did ask if I wanted to install IDE driver and I said yes. It then asked to over-write what I already had there (I said yes to that too). As the file names streamed-by, I though I saw some filenames with nv... listed. So, bottom line, is I'm not sure if I have the lates and greatest nVidia SATA drivers installed. How can I find out what drivers are installed?
- As I mentioned in my previous post, I have also downloaded and unzipped the NVIDIA RAID CLASS DRIVER & NVIDIA Nforce Storage Controller (20 files, 1.3 MB total) from the MSI site; however, I don't know how to "install" this now that I have the files. There are a couple of .exe and a .bat file (bit no setup.exe).
I may already have everything I need to partition and format these drives. I just want to bve sure I'm not skipping a step that is essential to optimal performance.
Thanks -
- bbdude

System suddenly won't power on (MSI K8N NEO2 PLATINUM NFORCE3)

System specs are
COOLERMASTER TAC-T01 WAVE MASTER ALUMINUM ATX 4X5.25 1X3.5 4X3.5INT case
MSI K8N NEO2 PLATINUM NFORCE3 ULTRA S939 AGP 5PCI SATA 1394 SOUND 1000LAN
KINGSTON HYPERX 1024MB DUAL CHANNEL KIT PC3500 2X512MB DDR 433MHZ 184PIN
ATI Radeon X800XT PE AGP
SEAGATE BARRACUDA 7200.7 200GB SATA 8MB 7200RPM 8.5MS OEM
CREATIVE SOUND BLASTER AUDIGY 2 ZS 7.1 1394 PCI RETAIL BOX
LITEON 16X DVD-ROM INT E-IDE RETAIl
MITSUMI FA404A 7-IN-1 FLOPPY DRIVE & FLASH READER CF/SM/SD/MMC/MS
LG 4163b dvd burner
Nothing has ever been overclocked on this system.
Everything is plugged into a Belkin Surgemaster powerbar.
I haven't mentioned the power supply. I'll get to that. I have been using an ANTEC NEOPOWER 480W POWER SUPPLY (ATX12V DUAL 12V RAILS ACTIVE PFC W/ DETACHABLE OUTPUT CABLES) for about a year on this system without
any issues. One morning, I wake up, hit the power button on my coolermaster case, and nothing happens.
CPU fan won't even spin. Nothing happens.
O.k., blown power supply, I think . . . .
So I take out my Antec and put it in another system. That system turns on
without any problems.
Hmm . . .
I come here, and I read posts about
potential compatibility issues with Antec power supplies. But if it's a compatibility
issue why was my system working for about a year?
O.k., fine. I'll buy a Enermax 535W EG565P-VE FMA 24P (115/230 VAC) power supply.
I just plug it into the mainboard (nothing else). Hit the power button . . .
The CPU fan spins for half a second, and then nothing.
Did my motherboard just suddenly die for no reason?
Any suggestions?

Pull the AC plug from PSU and set cmos in clear position with battery removed for atlest 20 minutes perhaps longer .
Then try to post the system barebone .
Just cpu,1 pcs memory in slot 1 , gfx card , and keyboard in PS2.
No usb devices at all including card reader and no pci cards harddisks or cdoms/dvd/floppy.
It could also be caused by a short or a malfunctioning fan connected to mobo.
Try to disconnect all case fans from mobo headers if you have any connected to additional fan holders.
The chipset fan can also be disconnected momentarily just to see if it posts.
If none of this helps , replace cmos battery and try again .

MSI K8N Neo2 Platinum slows down

Hi,
I have a little problem with my new K8N Neo2 Platinum. I installed Windows XP and the newest nForce drivers but if I copy files over LAN (tested both LAN-Ports) or install big applications my music played with winamp slows down. It's played with half speed. In addition to that my mouse pointer is very slow. After the setup or copying files everything is how it should be again. How can I solve this problem?
My system:
AMD Athlon64 3500+ (Winchester)
MSI K8N Neo2 Platinum-54G (tried different bios releases)
1024MB Corsair XMS Twinx DDR500
ATi Radeon 9800 Pro
2 80GB Maxtor S-ATA (DMA Mode enabled)
Creative Labs SoundBlaster Live! Player 5.1
MorLipf

Hello,
I copy files to my bro sometimes, 5Gb - all the steam GCF files for CS/HL/CSS/HL2.
My network usage is 80%-92%
My CPU usage is always under 15%.
It is worse when using 512Mb but as you have 1Gb it shouldn't be bad.
Check in the device manager, your cd drives should be set to DMA mode.

K8N Neo2 platinum & 750g sata RAID issue

Hi there I have an issue with booting up. I have 1 200g Western digital HDD where windows is installed and I have 1 further 500g WD drive which were both fine until I decided to buy 2 samsung 750g HDD's to run in RAID. I have installed the drives in RAID and formatted but I am having a problem with booting.
If I reset, the computer keeps rebooting at the detection stage, powers off and keeps doing it over and over. Sometimes it will go through if you wait long enough. When I turn the power on and off it will go through the detection stage no worries every time but then at the XP loading screen it will freeze there. Sometimes it goes through and I will boot into XP fine and other times I can't get in.
I have the latest Bios 7025V1D but I am wondering if this issue is bios related because of the 750g size... The problem has only started since I have installed the two 750g HDD's in RAID. Does this bios version support 750g HDD's? Is there an updated BIOS to fix this problem somewhere?
I have 2gig of ram, 3500+ processor, latest Nforce3 drivers from Nvidia, RAID drives on sata ports/3/4, 500gig WD on sata port 1, 200 gig WD is HDD is IDE, Windows SP2 and all updated, ummmmmm everything else is fine I'm fairly sure.
I had a few troubles installing the RAID drivers because windows didn't want to accept the drivers I downloaded from here and did not want to accept the drivers in windows. I ended up getting it the drives to come on-line through the use of START/NVIDIA corp/ NVIDIA RAID program (cant remember the name, typing this on another computer).
Any ideas would be greatly and very muchly appreciated!
Terry.

Ok My PSU is: WideTECH 550w, +3.3v=33a, +5v=36a, +12v=25a, -12v=1.0a, +5vsb=2.5a.
I am only running 3 HDD's at the moment, the 2 750's and the 1 200gig. I have left the other 500gig unplugged until I get this problem sorted. I don't have a cd rom plugged in or a floppy. I only connect them when I need to because this computer is setup to be a storage server and I use my other pc for anything dvd related etc. The only other thing which is chewing power is the video card which is an old 6800gt ultra. So basically the power issue was fine until I installed the two extra HDD's and as I have unplugged the 500gig for the time being its only really one extra HDD which shouldn't be an issue. Oh I have two 80mm case fans using the psu aswell.
As for my other specs: I have 1 gig of Geil dual channel RAM 2x512 sticks, CPU=AMD Athlon64 3500+, MB is MSI K8n Neo2 Platinum, Vid card= Leadtek geforce 6800gt ultra 256 agp, You know about my HDD's but here they are again= 1x 200g WD caviar IDE, 1x 500g WD caviar sata(1 I think), 2 x 750g samsung sata (2 I think), OS = XP Home SP2 with all lasest automatic updates, latest BIOS etc etc etc....
My windows is a legit copy as well.
You mentioned putting my HDD's into sata 1 mode... I was of the opinion that my motherboard does not support sata2 anyway and would not allow them to run in anything but sata1?? If I did want to change the sata mode where would I do this anyway?
Thanks for your reply but I don't think it has to do with psu or sata mode although I'm interested about this sata2 thing, please explain.
Thanks in advance,
Terry.

K8N Neo2 Platinum crashing/reboot in Windows....

After some minor problems with my systems (and almost a year since i did it last) i decided to do a clean install of Windows.
It all worked out well until i tried to deactivate the onboard Nvidia Gigabit LAN port. 1-2 seconds after hitting "deactivate" the computer reboots with no warning what so ever (like hitting the resetbutton). This happened EVERY time i did that. I had installed all the latest drivers for my GFX, Sound and MoBo. The MoBo drivers were the Nforce package from nvidia.com. I then downloaded the MoBo drivers from MSI's homepage and installed just the somewhat older drivers for the Nvidia Gigabit LAN. That fixed the problem with rebooting Windows.....
.....sort of. Now the computer reboots at random (either idle or working on something like photoshop) and has done so 4 or 5 times in the last week since i reinstalled Windows. I have never had this problem before.....
Could it be that i installed Nvidias own drivers instead of the MSI drivers ? I can't remember wich one i installed last time almost a year ago. I can't even remember if i ever updated them. If it ain't broke, why fix it ?
I have another problem thats not MSi related but how the hell do you uninstall the Creative Gameport ? I have unhooked it from my Audigy 2 soundcard but it still shows up in the devicemanager as a working device. Last time i installed windows i never got it to work (a known fact that the gameport isn't supported under Win XP). The strange thing is that this time it installed properly and seemed to be running before i unhooked it.....
If i don't get a working answer from this i will try reinstall Windows again....
So...
What drivers should i use on my Mobo ? Nvidia or MSI ?
// John - Sweden
AMD64 +3500
K8N Neo2 Platinum
Kingston Value Ram 2x1024
Asus ATI XT800 P.E
SoundBlaster Audigy 2 Platinum

Quote from: trifix on 14-January-06, 05:28:33
I have another problem thats not MSi related but how the hell do you uninstall the Creative Gameport ? I have unhooked it from my Audigy 2 soundcard but it still shows up in the devicemanager as a working device. Last time i installed windows i never got it to work (a known fact that the gameport isn't supported under Win XP). The strange thing is that this time it installed properly and seemed to be running before i unhooked it.....
the gameport is on your soundcard, what you have unhooked is only the extension bracket (i guess). so as long as your soundcard is in the system, the gameport will show up in the device list. nothing wrong with that one. instead of uninstalling it, just disable it from the device list.
i like to use mobo manufacturer's driver over the chipset maker because technically, MSI will release the drivers after they do some testing with them.

K8N Neo2 Platinum troubles.

This will be my first post here, and I hate it to be a problem post. Anyway, I built my own computer about 2 months ago, and I seem to have a problem with 2D applications. Here is my setup before I show you what I mean.
Mobo MSI K8N Neo2 Platinum
CPU Athlon 64 3000+ S939
PSU Antec 350W
GPU PNY Geforce 6800GT 256MB AGP
200GB Maxtor SATA HD
Sony DVD-RW
1 GB Mushkin PC3200 DDR Ram
OS Windows XP Pro
Ok, here is my exact problem. I seem to have trouble playing most MPEG, AVI, and WMV video types. I say most, because some will work ok. I have a picture of my problem here:http://img.photobucket.com/albums/v281/ZeroX585/hmm.jpg
There seem to be lines that appear across my video, and some 2D games such as Doom, Zsnes, and Worms world party. They also seem to appear when certain colors are shown during playback of videos and games, (mostly the darks and blacks.) 3D games work FINE, (Half Life 2, Doom 3, Far Cry are perfect). No errors what so ever. I have also noticed that this happens also when the program is dependent on some DirectX resources. I have uninstalled and reinstalled DX9 about 3 times, I have my latest Graphics drivers, I have my latest Windows Updates, I have the latest Mobo chipset drivers and such as well. I have also installed Windows XP again. I am not certain that this is a complete motherboard issue, as I do not have parts to switch out, but I am lost as to what I can do next. I HAVE replaced the GPU with an older ATI Radeon 9000, and it still happens. I highly doubt that the problem would lie within the CPU, but it's probable. I have reseated all the parts in the computer, and checked over my motherboard to make sure there isn't any damage to it. I am lost as to what I can do next though.
There is one thing I have noticed though, is if I go into my Display Properties and take the Hardware Acceleration tab down to "Disable all Direct 3D and Direct Draw Accelerations", the 2D programs work FINE. But if it goes even one notch up, it goes back to the lines. Anyone know what this could be related to?? Thank you for your help.

Before I had my 6800 GT, I was using the Radeon 9000, and I did use Driver Cleaner 3 to remove the Radeon driver. I also used Driver Cleaner when I update the Nvidia drivers, and I've done this a few times as well. I've tried using the Nvidia direct drivers (Current version), and I am currently using the PNY version of the Nvidia drivers, all the while using Driver cleaner to remove the old drivers before installing the new ones. I have not tried any games or videos in safe mode though, I think I will do that. I will get a screen shot of Doom if I can. By the way, I am not certain what you mean by "Be sure to run the Nvidia option, not the Nforce option."

K8N-Neo2 Platinum pauses for 25 sec at boot, nvatabus.sys the problem?

All,
After POSTing normally and starting to load Windows XP, my system halts at the Windows XP splash screen for about 25 seconds. Nothing happens, no disk activity or anything, the system just sits there.
I used Microsoft's Bootvis utility to see what was happening. It turns out that the nvatabus.sys driver consumes 100% CPU at boot for 25 seconds then the system continues to boot normally. Does anyone else see anything like this?
I am running the latest nForce drivers from MSI. The driver in question:
NVIDIA nForce3 Serial ATA Controller 2.6
Driver Date 6/3/2004
c:\WINDOWS\System32\DRIVERS\nvatabus.sys 5.10.2600.0446
Windows XP SP1
I have a RAID1 of two 160 GB SATA drives. The mirror is healthy and working fine.
After booting the system is rock-solid stable, no problems there. It's just this unexplained pause at boot. Does anyone have any ideas how to fix this?

ok check it out guy's this thing drove me insane all night last night and most of today. I was ready to return everything and give up. But alas all is not lost. Here is the rundown on what i just did.
My Equipment:
Athlon 64 3800+(w/ stock fan)
MSI K8N Neo2 Platinum Socket 939
2X512 Corsair TWINX1024-3200XLPRO ( with the cool led's )
2 SATA HD (1 Maxtor Diamond10 300 GB w/ 16mb cache, 1 Segate 160GB w/8mb cache)
PP&C 425 ATX Deluxe
Radeon 9700 Pro ( cat 4.8 )
Audigy2 ZS
Sony Floppy
Sony 8x52x52x32 DVD Rewrite
I have been reading and reading just like all you guy's. On a few websites i would pick up bits and pieces on what to try. Heres what i did. Upon Boot up i entered the bios. I then went to Cell Soft and adjusted my timings for my memory. I was at 2.5 not 2.75. I then set my speed down to 166. Exited and restarted. Big mistake everything ri=uns terrible slow and my expensive DDR 400 memory was showing up correctly at 333. Rebooted again entered the bios. reset my speed to 400. Then set the Overclock feature to manual. Set my timings at 2,2,5,2 200 and 2.75 volts. After saving settings and exiting I then turned off the computer. As per some other suggestions I moved my Audigy2 to the bottom most pci slot the one above the orange slot. I moved my memory to slots 2 and 4. I moved my SATA to slots 3 and 4. I rebooted went into the bios again and setup all my voltages. CPU was Auto, AGP was max yellow setting. Memory still at 2.75. I disabled the onboard serial and parrallel ports. Rebooted
Fearing the worst,
5 seconds, 10 seconds, windows screen loging prompt. There was nothing wrong at all. It rebooted effortlessly. It re found my Audigy card and wanted driver but that was it. I am going to reboot a few more times and then run sisandra to test. I hope some of this will help you. I post in a few after some of those reboots.

K8N NEO2 Platinum Dead once again

Similar Messages

Maybe you are looking for