K8N Neo2 Platinum MB + SATA Hard Disks

Hi,
I would like to use some additional disk in my PC and therefore buy SATA disks.
The OS is WIN XP Pro and I want to keep my IDE configuration which is:
C:\ = IDE hard disk Primary Master
E:\ = IDE hard disk Prmary Slave
D:\ = DVD Secondary Master
F:\ = IDE hard disk secondary slave
and to this I want to add just as data storage SATA 300GB hard disks (¿ up to 4 ? is that possible ?)
regards Rainer

I am not familiar with K8N Neo2-F so consult your manual to confirm my answers to your questions:
1- "Is this also the case for the SATA connectors on the K8N Neo2-F ??" Highly likely since your motherboard is a stripped down version of the Neo2 Platinum.
2- "And do SATA 1&2 require different drivers than 3&4?" For normal SATA operation these SATA drives are respectively contol by your NF3 chipset and you Realtek chipset. When you install or update your Nvidia & Realtek driver package you install all that is required to run normal SATA operation. Should you decide to use a RAID configuration with your SATA drive then another RAID specific driver would have to be installed at system level.
3- "Also, is there a significant increase in performance when going from PATA to SATA on this series of mobos?" My answer does not take into account RAPTOR HDs which are in a super class of their own. Medium to High end latest PATA & first generation SATA HDs in the 7200 RPM class are promoted by their OEM as having respective top transfer speeds of 133 and 150 MB/s. Comparing my Seagate 120 gigs PATA HD to my other two Seagate 200 gigs SATA HDs is not very scientific since they are not all 200 Gigs. Therefore use discretion interpreting results.
a. PATA - Peak transfer = low eighties ; Steady Transfer = high sixties
b. SATA - Peak transfer = mid nineties ; Steady Transfer = low eighties
It has ben a while since I did these PATA/SATA test so I am working from memory only. One thing that however sticks in my mind is that the delta between my PATA & SATA drives, for peak and steady performance, was very close to 12 MB/s in favor of first generation SATA. Could this be possibly related to (150-133), I do not know for sure.
SATA II generation are now coming to market. These new generation SATA II drives will most likely widen the performance gap between them and older SATA I or PATA drive.
Take good care,

Similar Messages

K8N Neo2 platinum & 750g sata RAID issue

Hi there I have an issue with booting up. I have 1 200g Western digital HDD where windows is installed and I have 1 further 500g WD drive which were both fine until I decided to buy 2 samsung 750g HDD's to run in RAID. I have installed the drives in RAID and formatted but I am having a problem with booting.
If I reset, the computer keeps rebooting at the detection stage, powers off and keeps doing it over and over. Sometimes it will go through if you wait long enough. When I turn the power on and off it will go through the detection stage no worries every time but then at the XP loading screen it will freeze there. Sometimes it goes through and I will boot into XP fine and other times I can't get in.
I have the latest Bios 7025V1D but I am wondering if this issue is bios related because of the 750g size... The problem has only started since I have installed the two 750g HDD's in RAID. Does this bios version support 750g HDD's? Is there an updated BIOS to fix this problem somewhere?
I have 2gig of ram, 3500+ processor, latest Nforce3 drivers from Nvidia, RAID drives on sata ports/3/4, 500gig WD on sata port 1, 200 gig WD is HDD is IDE, Windows SP2 and all updated, ummmmmm everything else is fine I'm fairly sure.
I had a few troubles installing the RAID drivers because windows didn't want to accept the drivers I downloaded from here and did not want to accept the drivers in windows. I ended up getting it the drives to come on-line through the use of START/NVIDIA corp/ NVIDIA RAID program (cant remember the name, typing this on another computer).
Any ideas would be greatly and very muchly appreciated!
Terry.

Ok My PSU is: WideTECH 550w, +3.3v=33a, +5v=36a, +12v=25a, -12v=1.0a, +5vsb=2.5a.
I am only running 3 HDD's at the moment, the 2 750's and the 1 200gig. I have left the other 500gig unplugged until I get this problem sorted. I don't have a cd rom plugged in or a floppy. I only connect them when I need to because this computer is setup to be a storage server and I use my other pc for anything dvd related etc. The only other thing which is chewing power is the video card which is an old 6800gt ultra. So basically the power issue was fine until I installed the two extra HDD's and as I have unplugged the 500gig for the time being its only really one extra HDD which shouldn't be an issue. Oh I have two 80mm case fans using the psu aswell.
As for my other specs: I have 1 gig of Geil dual channel RAM 2x512 sticks, CPU=AMD Athlon64 3500+, MB is MSI K8n Neo2 Platinum, Vid card= Leadtek geforce 6800gt ultra 256 agp, You know about my HDD's but here they are again= 1x 200g WD caviar IDE, 1x 500g WD caviar sata(1 I think), 2 x 750g samsung sata (2 I think), OS = XP Home SP2 with all lasest automatic updates, latest BIOS etc etc etc....
My windows is a legit copy as well.
You mentioned putting my HDD's into sata 1 mode... I was of the opinion that my motherboard does not support sata2 anyway and would not allow them to run in anything but sata1?? If I did want to change the sata mode where would I do this anyway?
Thanks for your reply but I don't think it has to do with psu or sata mode although I'm interested about this sata2 thing, please explain.
Thanks in advance,
Terry.

Reboot problem with MSI K8N Neo2 Platinum and 250 GB SATA HDD

I'm having a "reboot" problem with my MSI K8N Neo2 Platinum. After turning my system on it will run without any problems, until I reboot. After a reboot it will always hang after the initial windows-bootscreen. The HDD-light will remain on. If, instead of going into Windows XP SP2, I try to enter the BIOS after a reboot (DEL) the system will also hang (blank screen with blinking cursor).
It started doing this after I installed the Maxtor 250 GB SATA disk. Before, I didn't have problems rebooting. If I disconnect the Maxtor drive I can reboot and enter BIOS and Windows each and every time. Reconnecting the Maxtor 250 GB SATA drive will return the reboot problem. I always have to use the power swith to get a working system again. It's not enough to do a hard reset (this has the same effect as rebooting).
Here are the details of my system:
MSI K8N Neo2 Platinum (BIOS 1.B)
Athlon 64 3200+ (Winchester, 2 Ghz, 512 KB cache, stepping DH-D0)
2 x Kingston KVR400X64C25/512, 512 MB, DDR, PC3200 (2,5-3-3-8 T1)
Asus Radeon AX800 Pro (256 MB)
PSU Antec Sonata 380W
HDD Maxtor 80Gb ATA (6Y080P0, Pri Master)
HDD Seagate 250Gb SATA (ST3200822AS)
HDD Maxtor 250Gb SATA (6V250F0 - jumpered in SATA150 mode, the mobo wouldn't work with the drive in SATA300-mode)
Aopen COM5232/AAH Pro CD-Writer ATA (Sec Master)
BenQ DW1640 DVD-Writer ATA (Sec Slave)
P.S. The NVidia IDE-drivers are NOT installed. System is not overclocked.

Thank you for all the replies. Upgrading to the latest Nvidia IDE-drivers did not fix my problem. Moving to other SATA-ports did not help either. Upgrading the mobo's BIOS is not really an option (I'm using one version before the most recent and there isn't anything in the fixlist of the latest BIOS).
Now I've contacted Maxtor for (hopefully) a new firmware.
Quote from: rogueUK on 31-July-06, 16:55:42
insego please use the SEARCH BUTTON
I did use the search function to find other people with similar problems. The reason I started a topic of my own was because of the text you get while joining:
Quote
Do not hijack another persons topic. If you have a similar problem, start your own thread anyway.
Maybe in retrospect I should first have tried the solutions in other topics.

SATA HDD installation on K8N Neo2 Platinum, Non-RAID, Non-Bootable

Hi-
I’m a rank newbie on this forum (first post). I have a K8N Neo2 Platinum Mobo, which I’ve recently gotten up and running, with Windows XP-Pro SP2 installed on a single IDE drive. I would now like to add 2 SATA drives. I don’t need or want the SATA drives to operate in a RAID array, nor do I want them to be bootable. I want to use them independently for data storage. I read the following thread (I am posting here on a separate thread per the author’s wishes not to get his original thread too junked-up) :
Single SATA or Multiple Drive Array Setup FAQ
I have not yet plugged-in either of my SATA drives, because I don’t want to risk corrupting my existing boot (IDE) drive. I just had a few questions about the procedure given in the referenced thread, in the Single Drive Setup:
- Step 14 States: “Make sure the “RAID Mode” is Stripping and Striping Block at 64k or Optimal. Hit F7 (Finish)”. Is this correct for a single non-boot drive?
- Step 22 States: “As most of you know when you enter the Setup for Win2k/WinXP you will need to hit F6 to load additional drivers for other SCSI devices.” I assume this means I need to boot from the Windows CD. Is this true even if I already have Windows installed on an IDE HDD on this system? At what point will I need to hit <F6> ? Will I be prompted to do so?
- I have downloaded (from the MSI website) the NVIDIA RAID CLASS DRIVER & NVIDIA Nforce Storage Controller (20 files, 1.3 MB total). Should I put these on a floppy? Or can I access them from a directory on my OS HDD?
- Should I go ahead and plug-in both of the 2 SATA drives I want to add to the system before beginning the driver installation? The only reason I would consider installing them one at a time is if it eliminated any confusion between RAID vs. independent (I want independent operation). If I do install them one at a time, do I have to install the driver twice?
Any help would be appreciated.
- the bbdude

OK Thanks JeanGuy and ssjkakaroto,
I have connected both of my SATA drives. They are enabled in BIOS but not set to RAID. I booted up to Windows on my IDE drive. In Disk Manager, the display shows Disk 0 (C: System), Disk 1 and Disk 2 as uninitialized, and my DVD (D:) drive. At this point, I could probably go ahead and run the Initialize and Convert Disk Wizard to get these disks formatted and be dome with ot now. Before I do that though, I just have a couple of more questions.
- I had already loaded the nVidia nForce3 system driver prior to installing the SATA drives, but I went ahead and did that again after installing the SATA drives and restarting Windows. I used Live Update, which went out to the MSI site and found version 5.03 of the nVidia nForce3 system driver. I'm not sure how to find the "Nvidia 5.10 driver package which include the latest SATA driver", ssjkakaroto referred-to. The Live Update install procedure did ask if I wanted to install IDE driver and I said yes. It then asked to over-write what I already had there (I said yes to that too). As the file names streamed-by, I though I saw some filenames with nv... listed. So, bottom line, is I'm not sure if I have the lates and greatest nVidia SATA drivers installed. How can I find out what drivers are installed?
- As I mentioned in my previous post, I have also downloaded and unzipped the NVIDIA RAID CLASS DRIVER & NVIDIA Nforce Storage Controller (20 files, 1.3 MB total) from the MSI site; however, I don't know how to "install" this now that I have the files. There are a couple of .exe and a .bat file (bit no setup.exe).
I may already have everything I need to partition and format these drives. I just want to bve sure I'm not skipping a step that is essential to optimal performance.
Thanks -
- bbdude

Which SATA port on the K8N Neo2 Platinum?

Hi! I recently got a 160GB Maxtor DiamondMax 9 Plus hard drive, but I have read somewhere (i forgot where I read it) that two S-ATA ports on the K8N Neo2 Platinum will corrupt your hard drive data if you overclock. I dont know if this is still true (I have BIOS ver 1.8) but please could someone tell me which port I should connect my S-ATA drive to? (the only drive I have at the moment is a 160GB IDE drive). I dont want RAID. Thanks!

Quote from: Supershanks on 14-June-05, 18:46:14
If u go over 230 sata 1/2 are liable to corruption.
230GB i assume?

RESOLVED - K8N Neo2 Platinum problem with large Seagate disk

Hi All,
I've been running this system for 4 years and I'm very happy with it. But I've run into a problem:
I'm trying to exchange my 120 GB Seagate Barracuda systemdisk with a 500 GB Barracuda and I can't install XP with SP2.
First I tried to clone the old HD with Norton Ghost and Acronis True Image. The cloning looked fine but after taking the old HD out and moving the new one to P-ATA 1 as Primary Master I get an "error - no operating system found". I also tried a fresh install from CD. After the CD reboots the system I get the same error.
The HD is present in BIOS with the right parameters and all is looking well - but still no go.
I've fiddled around in BIOS (vers. 1.3) with the different settings (LBA, Large, Auto, Csh.) The last 2 options gives the "no operating system" error and the first 2 gives a "disk error" although Seagate says that I should change settings to "LBA".
I only have the new HD in the machine. I also tried fixboot and fixmbr. I can see all the installed files when I put it in as a slave.
So my question is:
Does the K8N Neo2 Platinum have a problem with large hd's as system disk?
Or is this a Seagate or Windows problem ?
Any help is much appreciated!
Mads

Actually that was the first thing I did just to see if the drive worked :-) - except that I had it as master on the second ide cable. It formats like it should and all partitions report "healthy". The only difference is that the new drives c-partition is set as active (can't find a way to change it back) - while the old one is set as system. Could this make a difference ?
Since neither cloning nor a fresh install works I think the problem is something else. Maybe I should try Seatools and see if that makes any difference.
Thank's all for help so far! - Other suggestions ?

How should I setup a SATA HDD on K8N Neo2 Platinum?

I bought a 200Gb SATA hard disk (Maxtor 6V200E0). This is the first time I work with SATA HDDs.
I plugged the HDD as I always did with an IDE HDD, and installed Windows XP -I have configured nothing-. The problem I'm experiencing is that sometimes Windows XP boots fine, and sometimes it doesn't. After the POST, the Windows Logo does never appear. I do not see anything.
Reading the Manual, I believe to understand that no matter if you only have one SATA HDD, I should setup nVRAID in the BIOS. Is that correct?. If I configure the nVRAID in the BIOS and setup RAID 0, should this problem disappear?. How should I setup my SATA HDD?. Is it the same to connect it to SATA1/SATA2/SATA3/SATA4 controller?. Or should it be connected into SATA1 -just because there's only 1 HDD in the system-?.
Thanks a lot!

Yes, unfortunatelly there's a major issue with this kind of HDDs and nForce3&4 chipset based mainboards. I found the following article at the Maxtor web-site -I asked them to send me the firmware upgrade; standing by-:
Question
I have heard or read that Maxtor drives are incompatible with nForce3 or nForce4 chipsets, or that I need a firmware update to make a Maxtor drive compatible with the nForce chipset. Is this true?
Answer
Note: This solution is only to be applied to the listed products and only when used with the nVidia© nForce3© or nForce4© chipsets. If you are unsure as to which chipset you have, please contact your motherboard manufacturer or visit your motherboard manufacturer's website for clarification.
Firmware updates are not upgrades. They offer no performance enhancements and exist only to provide specific compatibility resolutions. If you have a drive that is working properly in a computer, you do not need a firmware update.
Do not use a firmware update that is not authorized directly by Maxtor as there are variations of firmware for different revisions of drives that can render drives inoperable if applied to the wrong drive.
Applying firmware to a drive that is not authorized by Maxtor will void the warranty on the drive as this would be considered an unauthorized modification. Please see Maxtor's Limited Warranty Statement for more information.
If your drive came inside an OEM machine such as a Dell, Apple, Gateway etc., do not apply a firmware update at all as this will void the warranty which is held by that manufacturer. Please contact your OEM vendor directly.
The following issues have been identified with Maxtor SATA II drives and the nVidia nForce4 controller:
Data Corruption: If you are experiencing data corruption issues, the problem is not with the hard drive firmware. Please visit nVidia's website to update to the latest nVidia chipset drivers to resolve this issue. Make sure to be familiar with your motherboard specifications as there are several variations.
NCQ: If you are experiencing problems with NCQ (Native Command Queueing) please see nVidia's Knowledgebase ID 768 for more information with an issue nVidia is having with NCQ and the nForce4 chipset, and a forthcoming resolution. They also offer a solution to temporarily disable NCQ.
No Detection: If you are experiencing a problem with your Maxtor SATA-II drive not being detected by your nForce3 or nForce4 host controllers at bootup:
Note: This does not apply if your drive is connected to a non-nForce3 or nForce4 controller such as SIIG (Silicon Image), HighPoint, Promise etc. Many motherboards have multiple host controllers onboard so make sure you are familiar with your motherboard specifications and schematics.
The drives affected are those listed in the following table:
Model begins with:
Code (Firmware revision)
6B- or 7B-
BANC1980
BANC1B70
BANC1BM0
BANC1BY0
BANC1E00
6L- or 7L-
BANC1G00
BANC1G10
BANC1G20
6H- or 7H-
HA431BW0
6V- or 7V-
VA111610
VA101610
VA131610
VA141610
Example of a drive label:
Image
To check your current firmware revision on the drive without removing it from the system, use the Powermax diagnostic CD. Drive model, Serial and firmware Revision is displayed in the upper right hand corner after selecting the drive to test.
A firmware update to resolve this issue for Maxtor SATA II drives is available by contacting Maxtor Support. Please have the drive serial number and the Code number available, which will be listed on the top label of the drive itself.
Firmware updates will be issued for those drives experiencing this problem only, not for experimental troubleshooting. Due to the nature of a firmware code update, a drive can be potentially rendered inoperable so it is critical that data is backed up first.

Os/2 or beos on k8n neo2 platinum

i want to run beos on my system
or os/2
i have the k8n neo2 platinum
athlon 64 3500
1 gig geil ram
80 GB maxtor Pata hard drive
30 gb seagate Pata hard drive
60 gb SATA maxtor
ati card (wel figure that one out later)
BeOS 5 pro just reboots
and for some ungodly reason i cannot write my os/2 image files without some crap about "BAD TRACK 0" and i just bought a new pack of floppies. and it tells me this with EVERY disk
the only OTHER OS i can get to run is linux
which im quite fond of... "anything except WINDOZE"
I guess what my question is .....WHAT KIND OF VOODOO RITUAL DO I HAFTA PERFORM TO MAKE THIS WORK!!!!!!!
I dont have any chickens to bleed, but the neighbor does!!!!
Please help
ANY help would be GREATLY APPRICIATED!!!!!!!!!!!!!!!!!

Hi,
I tried to do the same with os/2 and MSI Neo4 Platinum/SLI and Athlon FX55.
OS/2 Warp 4 requires 256MB ram or less installed to do initial install. The first partition of HDD must be less than 2.06Gigs in order for the Kernel to compile.
EComStation has the newest version of OS/2. A Google search should take you right to Sundial's site.

MSI K8N Neo2 Platinum AND SATA2

i have MSI K8N Neo2 Platinum motherboard with 3500+ cpu and WD 160 hard sata disk.
I 'd like to ask if my MSI K8N Neo2 Platinum motherboard support sata2 hard disk drives, in order to know which HD to connect as a second HD drive, SATA or SATA 2 ??

It'll see SATA2 as regular SATA. You won't loose any speed either. There are no hard drives that actually benefit from SATA2 spec speeds. Well, maybe in isolated near theoretical benchmark cases one current model might be faster in SATA2 mode.
We just haven't got the technology yet.

IS my MSI K8N Neo2 Platinum FRIED!??

Ok I am assembling my first computer right now. I have the Motherboard (msi K8N Neo2 Platinum nForce 3 Ultra Socket 939) a gig of corsair pc3200 RAM, a Samsung 7200RPM hardrive, a Samsung DOuble layer CD/DVD burner, 5 fans, and AMD Athlon 64 3500+ (NCC). But when I plug everything into the motherboard, all the fans start spinning everything looks like its ine except the IDE ports. My CD-ROM wont go on and I just got it! everything is new out of the box. I have a single drive, the IDE ribbon conecting from the motherboard, then the master connecting to the CD-ROM. The jumper is still in there. The "system part" of the IDE ribbon is plugged into the IDE-1 on the motherboard. And my harddrive is SATA, when I plug that in, it doesnt look like its working either! All my power cables are fine because when I plug them into the fans they work...any suggestions?

Yapyap,
would have been nice to post solution.
Drop Ht from 5 to 4 in bios - cell menu as soon as you can get into bios.
How to clear the CMOS
1) disconnect the power cable.
2) push the power button to drain the capacitors
3) Move the CMOS jumper to the clear position, from it's original 1-2 position to 2-3
4) Wait a minute to be sure the CMOS has been cleared. Take your Time
5) Return the CMOS jumper to it's original position 1-2
6) Plug in power cable.
7)restart computer
8) enter bios and select load optimized Bios defaults - save & exit
9) let pc reboot, if you have any settings you want changing do them now.
like HT Settings hard disk boot order etc.,
10) hopefully youll boot

K8N NEO2 Platinum rebooting

Hi all,just got myself a 64bit MSI K8N NEO2 Platinum board & a 3200+,am happy with it but a couple of days ago i got a blue screen with a long message that i didnt have time to read before the pc rebooted,after the reboot i checked the event viewer log file in administrative tools/control panel but couldnt narrow it down as my particular error code wasnt among the possible causes.
Among some of the possible causes were incorrectly installed USB drivers or the BIOS,i downloaded the latest BIOS update before this problem started(V1.40) which i am using now,i used the MSI live update software to flash it which i did in windows mode.Sorry for prattling on!well it did it again tonight and i managed to read a bit of the writing on the blue screen which mentioned flashing the bios to the latest version.I was wondering if anyone else is having the same problem and if so could you please advise me? Thanks for your patience and any help Heres my sys specs:
Model: AMD Athlon(tm) 64 Processor 3200+
Speed: 2.01GHz
Model Number: 3200 (estimated)
Performance Rating: PR3015 (estimated)
Type: Standard
L2 On-board Cache: 512kB ECC Synchronous Write-Back (16-way, 64
byte line size)
Bus(es): ISA AGP PCI USB FireWire/1394
MP Support: 1 CPU(s)
MP APIC: No
System BIOS: Phoenix Technologies, LTD 6.00 PG
Mainboard: MS-7025
Total Memory: 1023MB DDR-SDRAM
Model: Micro-Star International Co Ltd (MSI) ???
(00E1)
Front Side Bus Speed: 1x 201MHz (201MHz data rate)
Model: Advanced Micro Devices (AMD) Athlon 64 /
Opteron HyperTransport Technology
Configuration
Front Side Bus Speed: 1x 201MHz (201MHz data rate)
Total Memory: 2048MB DDR-SDRAM
Memory Bus Speed: 2x 201MHz (402MHz data rate)
Monitor/Panel: CTX EX950F series
Adapter: RADEON X800 Series
Adapter: RADEON X800 Series Secondary
Removable Drive: Floppy disk drive
Hard Disk: Maxtor 6Y080L0
CD-ROM/DVD: HL-DT-ST DVDRAM GSA-4081B (CD 32X Rd, 24X Wr)
(DVD 4X Rd, 3X Wr)
CD-ROM/DVD: MSI CD-RW CR52 (CD 40X Rd, 52X Wr)
CD-ROM/DVD: AXV CD/DVD-ROM SCSI CdRom Device (CD 32X Rd)
(DVD 4X Rd)
1.44MB 3.5" (A:): N/A
Hard drive (C:): 76.3GB (51.9GB, 68% Free) (NTFS)
CD-ROM/DVD (D:): N/A
CD-ROM/DVD (E:): N/A
CD-ROM/DVD (F:): N/A
Serial/Parallel Port(s): 1 COM / 1 LPT
USB Controller/Hub: Standard OpenHCD USB Host Controller
USB Controller/Hub: Standard OpenHCD USB Host Controller
USB Controller/Hub: Standard Enhanced PCI to USB Host Controller
USB Controller/Hub: USB Root Hub
USB Controller/Hub: USB Root Hub
USB Controller/Hub: USB Root Hub
FireWire/1394 Controller/Hub: VIA OHCI Compliant IEEE 1394 Host Controller
Keyboard: Standard 101/102-Key or Microsoft Natural PS/
2 Keyboard
Mouse: PS/2 Compatible Mouse
Device: Creative SB Live! series
Device: Creative Game Port
Model: EPSON Stylus CX3200
Windows System: Microsoft Windows XP/2002 Home (Win32 x86)
5.01.2600 (Service Pack 2)
Network Drivers Enabled: Yes
Warning 100: Large memory sizes should be made of
Registered/Buffered memory.
Tip 101: Large memory sizes should be made of ECC/
Parity memory.
>
>
Device Type: VGA Video Adapter
Device ID: bus 1, device 0, function 0
Windows Device Name: RADEON X800 Series
OEM Device Name: ATI Technologies ??? (4A49)
OEM Hardware ID: FUN_0, VEN_1002, DEV_4A49, REV_00
Device Name: PC Partner Ltd ??? (4A49)
Product ID: VEN_174B, DEV_0D42
Revision: A / 1 (0)
Version: 3.00
Command Queue Length: 256
Fast-Writes Support: Yes
Over 4GB Addressing Support: No
Isochronous Mode Support: No
Addressing Support: 32-bit
Data Transfer Modes Support: 4x 8x

My K8N Neo Platinum [754] did not include a NB fan. But this usually means the overall size of the heatsink is larger. If you remove the fan from yours, the size of the heatsink will not be big enough to cool your NB. As for temps, I've never seen my NB get hotter than 45'C. Note that the core on my NB should be slightly different than yours.
You could try to use the BIOS fan control for the NB. If set correctly, it should reduce some noise.

K8N Neo2 Platinum Ordered - Advice for a noob please

Hi there,
this seems like a great forum, was hoping someone could give me some advice - Im trying to pre-empt any major probs....
I am a relative noob to building P.C's - done a few P4 based systems before but this will be my first Athlon based. This systems primary use will be gaming. I have the following on order (should be with me next week) : -
a) MSI K8N NEO2 Platinum Edition SCK 939 Motherboad
b) AMD ATHLON 64 3500+ 64bit SCK 939 Retail Inc Fan
c) 160GB Maxtor Calypso 8mb Cache 7200 SATA DHH
Components I have already
a) Graphics Card - Nvidia 6800 GT
b) Memory - Generic 2 X 512MB PC2700 DDR333 RAM
c) Sound Card - Creative SB Live Value
d) PSU - Jeantech 450W (22a on 12V Rail)
e) Case - pretty generic full tower case - no fans attached
f) CPU FAN - COOLERMASTER HYPER 48 SUPER SILENT HEATPIPE
g) Spare Hard drive - 120GB Maxtor IDE Hard drive
h) DVD Drives - 1 x Pioneeer 108 / 1 x Pioneer 104
I) Monitors - Ilyama 17" TFT & Toshiba 32WL36P LCD
I have some 'noobish' questions - apologies for my ignorance : -
1) Memory - Will my memory be okay ? Should I ditch it and buy some Corsair DDR400 (which everyone else seems to have!). Will performance suffer if I stick with the DDR 333 ? Do I need to adjust settings in BIOS regarding memory timing ? (I only picked up on this from reading through other posts on this board, and am totally clueless on 'timing'- Ive never needed to adjust timing on any previous PC's....!)
2) Sound Card - will I be better off sticking with the onboard sound on the MSI K8N neo 2 ? Or for best performance do I go with the SB LIve ? (god its a nightmare trying to get updated drivers for this card), Would I get a noticable performance increase buying an Audigy 2?
3) Vcore / other power issues - Reading this forum Im kinda scared by many posts along the lines of "..for stability I need to change my memory voltage to xx-V" or "...for a stable system I needed to change my Vcore to xx-V". Will I need to change the Bios default values on this system just to get it to run stably??
4) CPU FAN - Are AMD stock fans any good ? My Hyper 48 is quite highly rated....
5) Im completely new to SATA drives, but Ive printed off the very useful install guide on this site (which I intend to use). Is there anything I need to look out for concerning adding my IDE drive also.
I think thats about it just now - if anyone can see any other potential problems with my specs then please let me know. Im really not trying to be negative / pessimistic - after all the reason I have went for this motherboard is that it is rated as one of the best. Im just a bit paranoid that the dreaded B.S.O.D awaits me!
On a more positive note - does anyone have similar system specs they use for gaming ? How well does HL2 / Doom3 / Farcry etc fly J ? I cant wait !
Thanks for the time

you may find these helpful
Overclockers Uk Power Supplies
This Week Only Enermax Noisetaker 485W EG495AX-VE(G) SFMA ATX2.0 PSU (CA-007-EN) Might be tempting
Scan International Power Supply

USB Keyboard (K8N Neo2 platinum)

motherboard k8n neo2 platinum, somehow my motherboard does not recog my usb keyboard. i have gone to bios and enabled USB mouse/keyboard , my mouse is ok no matter which usb front or back but the keyboard usb does not work on any of usb . does anyone have any idea (hardly used keyboard, nearly new) all usb are ok??. your help will be much appreciated.
1-Motherboard MSI 7025 K8N Neo2 Platinum Chipset nForce3-250Gb/Ultra
2-CPU AMD Athlon Dual Core 3800X2
3- Graphic card (MSI FX5700) nVIDIA GeForce FX 5700
4-Memory 2 X1 GB DDR 400 DIMM kingston
5-HDD Maxtor 6Y160M0 (160 GB, 7200 RPM, SATA
6- OS Window XP Prof sp2
7-power supply Be Quite BQT- P5-420W

Bosskiller thanks for the reply it is a micorisoft multimedia, yes i have tried the back usb no luck there either. here is the link for the keyboard
http://www.farassoo.com/product/keyboard/fcr-8800.htm
but i wonder if you can tell me why some system their front usb doesn't work with usb keyboard a few have said this to me. many thanks

K8N-Neo2 Platinum pauses for 25 sec at boot, nvatabus.sys the problem?

All,
After POSTing normally and starting to load Windows XP, my system halts at the Windows XP splash screen for about 25 seconds. Nothing happens, no disk activity or anything, the system just sits there.
I used Microsoft's Bootvis utility to see what was happening. It turns out that the nvatabus.sys driver consumes 100% CPU at boot for 25 seconds then the system continues to boot normally. Does anyone else see anything like this?
I am running the latest nForce drivers from MSI. The driver in question:
NVIDIA nForce3 Serial ATA Controller 2.6
Driver Date 6/3/2004
c:\WINDOWS\System32\DRIVERS\nvatabus.sys 5.10.2600.0446
Windows XP SP1
I have a RAID1 of two 160 GB SATA drives. The mirror is healthy and working fine.
After booting the system is rock-solid stable, no problems there. It's just this unexplained pause at boot. Does anyone have any ideas how to fix this?

ok check it out guy's this thing drove me insane all night last night and most of today. I was ready to return everything and give up. But alas all is not lost. Here is the rundown on what i just did.
My Equipment:
Athlon 64 3800+(w/ stock fan)
MSI K8N Neo2 Platinum Socket 939
2X512 Corsair TWINX1024-3200XLPRO ( with the cool led's )
2 SATA HD (1 Maxtor Diamond10 300 GB w/ 16mb cache, 1 Segate 160GB w/8mb cache)
PP&C 425 ATX Deluxe
Radeon 9700 Pro ( cat 4.8 )
Audigy2 ZS
Sony Floppy
Sony 8x52x52x32 DVD Rewrite
I have been reading and reading just like all you guy's. On a few websites i would pick up bits and pieces on what to try. Heres what i did. Upon Boot up i entered the bios. I then went to Cell Soft and adjusted my timings for my memory. I was at 2.5 not 2.75. I then set my speed down to 166. Exited and restarted. Big mistake everything ri=uns terrible slow and my expensive DDR 400 memory was showing up correctly at 333. Rebooted again entered the bios. reset my speed to 400. Then set the Overclock feature to manual. Set my timings at 2,2,5,2 200 and 2.75 volts. After saving settings and exiting I then turned off the computer. As per some other suggestions I moved my Audigy2 to the bottom most pci slot the one above the orange slot. I moved my memory to slots 2 and 4. I moved my SATA to slots 3 and 4. I rebooted went into the bios again and setup all my voltages. CPU was Auto, AGP was max yellow setting. Memory still at 2.75. I disabled the onboard serial and parrallel ports. Rebooted
Fearing the worst,
5 seconds, 10 seconds, windows screen loging prompt. There was nothing wrong at all. It rebooted effortlessly. It re found my Audigy card and wanted driver but that was it. I am going to reboot a few more times and then run sisandra to test. I hope some of this will help you. I post in a few after some of those reboots.

K8N Neo2 Platinum Checksum Error

Hi, I apologize if I break any rules here, but I tried to use the search option to locate an answer but couldn't find anything that helped me fully.
My problem is that when I try to turn on my computer, I get a message saying:
"Award Bootblock BIOS v1.0
Copyright 2000 Award Software Inc.
BIOS ROM checksum error
Keyboard error or no keyboard present.
Detecting floppy drive A media
INSERT SYSTEM DISK AND PRESS ENTER".
Except this, my computer is completely "dead", I cannot go anywhere. From what I have understood, my BIOS is corrupted, and I need to flash it. This should be done by inserting a boot floppy with added AWDFLASH.exe and a bios.bin. The thing is, I don't know how to find these files, or at least the correct ones. I have also tried to google for a solution, but haven't found anything satisfactionary. So this is kind of my last resort. I am very sorry if this is a newbie question, but I have almost no experience in this advanced (from my perspective) knowledge.
If someone could help me locate the correct verisons of the Award Flash utility and BIOS file, and write a short step by step-walkthrough of how to proceed, you would have my eternal gratitude.
My system is a 4 years old:
MSI K8N Neo2 Platinum 54G S939 with nForce 3 Ultra
Windows XP Home
AMD Athlon 64 3500+ 2.2 Ghz
Gainward GeForce 7800 GS 512 Mb
2x TwinMos 512 Mb RAM PC3200
Maxtor Diamondmax 200 Gb SATA
MS-7025 Ver: 1 is printed on the motherboard.

Quote from: go_for on 11-March-09, 03:04:25
This one is stuck in Award bootblock mode, will most likely need a re-flash from a bootable floppy disk.
Make a bootable floppy disk, in e.g WinXP.
Make a file with notepad, containing this line:
AWFL833D.EXE W7025NMS.1D0 /CC /CD /CP /QI /R /PY /SN
Save this file on this floppy by the name Autoexec.bat
Also add the two files AWFL833D.EXE and W7025NMS.1D0 on this floppy.
Power up the K8N Neo2 Plat. with this disk in the floppy drive. The flashing will begin, let it finish.
Remove floppy and reboot. If it succeeded, set all relevant values in BIOS and save&exit.
Quote
This one is stuck in Award bootblock mode, will most likely need a re-flash from a bootable floppy disk.
Not always, the same fake error message can came from bad memory stick too.
Also he didn't flash his BIOS before the message to appear.

K8N Neo2 Platinum MB + SATA Hard Disks

Similar Messages

Maybe you are looking for