K8N Neo2 Platinum Memory Issues

I have two Super Talent 512 DDR PC3200/400MHZ Memory Modules and attempting to use them as dual channel. I am getting some funny behaviour however. In windows mode, whenever I try to do something memory intensive the machine crashes and reboots. Normally I would say that this is an issue with a bad chip, run memtest86 and determine which chip is bad. Well the results are a bit strange. When ever I run memtest with both modules in either banks 0 and 1 or 2 and 3 (dual channel configuration) I get memory errors. I then test each module separately in bank 1 and get no errors. Do I have a setting wrong somewhere? Could this possibly be incompatible ram?
Can someone please enlighten me as to why this might be happening? If its a settings issue it would be helpful to know where and how I should set this. If it is a compatibility issue it would be very helpful to know what brands of memory people have used successfully for dual channel so that I don't get stuck with this problem again.
Thank you very much for any assistance anyone can offer.
Channon

Did you purchase the RAM from a 'chain' retailer? - like Best Buy or Circuit City, etc.? If so it is most likely dual-channel RAM. Now if you got them from your local 'junk peddler dealer' (that's what I call them) and the RAM chips were not sealed in a manufacturer's package, with their name on it, then you may have gotten screwed.
You can try installing one stick in slot 1 and the other in slot 3. That should set the system to single-channel mode. See if it runs okay and then run Memtest again. If the test passes then you've got yourself a set of 'fake' dual DDR. :(
If you got them at Best Buy (or whatever) that is a large store with a good replacement policy, you should have no trouble exchanging the RAM for a new set... and MAKE SURE THE PACKAGE SAYS DUAL-CHANNEL.
Now on the other hand... if they came from a local computer shop, take them back to where you got them, shove them in the guy's face... tell him he's a liar and will replace your RAM with the correct sticks. If he refuses you can always shove each chip into his eye sockets to get your revenge.

Similar Messages

K8N Neo2 platinum & 750g sata RAID issue

Hi there I have an issue with booting up. I have 1 200g Western digital HDD where windows is installed and I have 1 further 500g WD drive which were both fine until I decided to buy 2 samsung 750g HDD's to run in RAID. I have installed the drives in RAID and formatted but I am having a problem with booting.
If I reset, the computer keeps rebooting at the detection stage, powers off and keeps doing it over and over. Sometimes it will go through if you wait long enough. When I turn the power on and off it will go through the detection stage no worries every time but then at the XP loading screen it will freeze there. Sometimes it goes through and I will boot into XP fine and other times I can't get in.
I have the latest Bios 7025V1D but I am wondering if this issue is bios related because of the 750g size... The problem has only started since I have installed the two 750g HDD's in RAID. Does this bios version support 750g HDD's? Is there an updated BIOS to fix this problem somewhere?
I have 2gig of ram, 3500+ processor, latest Nforce3 drivers from Nvidia, RAID drives on sata ports/3/4, 500gig WD on sata port 1, 200 gig WD is HDD is IDE, Windows SP2 and all updated, ummmmmm everything else is fine I'm fairly sure.
I had a few troubles installing the RAID drivers because windows didn't want to accept the drivers I downloaded from here and did not want to accept the drivers in windows. I ended up getting it the drives to come on-line through the use of START/NVIDIA corp/ NVIDIA RAID program (cant remember the name, typing this on another computer).
Any ideas would be greatly and very muchly appreciated!
Terry.

Ok My PSU is: WideTECH 550w, +3.3v=33a, +5v=36a, +12v=25a, -12v=1.0a, +5vsb=2.5a.
I am only running 3 HDD's at the moment, the 2 750's and the 1 200gig. I have left the other 500gig unplugged until I get this problem sorted. I don't have a cd rom plugged in or a floppy. I only connect them when I need to because this computer is setup to be a storage server and I use my other pc for anything dvd related etc. The only other thing which is chewing power is the video card which is an old 6800gt ultra. So basically the power issue was fine until I installed the two extra HDD's and as I have unplugged the 500gig for the time being its only really one extra HDD which shouldn't be an issue. Oh I have two 80mm case fans using the psu aswell.
As for my other specs: I have 1 gig of Geil dual channel RAM 2x512 sticks, CPU=AMD Athlon64 3500+, MB is MSI K8n Neo2 Platinum, Vid card= Leadtek geforce 6800gt ultra 256 agp, You know about my HDD's but here they are again= 1x 200g WD caviar IDE, 1x 500g WD caviar sata(1 I think), 2 x 750g samsung sata (2 I think), OS = XP Home SP2 with all lasest automatic updates, latest BIOS etc etc etc....
My windows is a legit copy as well.
You mentioned putting my HDD's into sata 1 mode... I was of the opinion that my motherboard does not support sata2 anyway and would not allow them to run in anything but sata1?? If I did want to change the sata mode where would I do this anyway?
Thanks for your reply but I don't think it has to do with psu or sata mode although I'm interested about this sata2 thing, please explain.
Thanks in advance,
Terry.

Kingston HyperX Memory & K8N Neo2 Platinum

Hello.
I have a MSI K8N Neo2 Platinum board (BIOS 1.3) with AMD 64 3000+ 939 CPU.
I am trying to run this with 2 Kingston HyperX PC3200 512MB memory (KHX3200ULK2/1G). This is the latest "Ultra-low Latency" memory from Kingston.
When I run this memory with NO overclocking at 2-2-2-5-1 at 2.7 volts (standard setting for this memory) with a single module, I get NO errors. When I try both chips in dual-channel mode, I get errors (on MemTest86).
(I also get errors if I run this memory on "Auto" setting in BIOS)
I CAN run 2 sticks of Crucial PC3200 512MB (regular, not Ballistix) at standard settings in dual-channel with no errors.
Has anyone got this memory to work on this board in dual-channel mode? If so, how? At what timings?
Any help would be greatly appreciated.

Quote
Originally posted by Xak
Quote
Originally posted by GlennVidia
In the meantime...
Try loosening up the memory timings first, start with 2-2-2-8 thru 2-2-2-11
Then if no luck try 2-3-2-6 thru 10 or 11 you may even have to resort to 2.5 3-3-X
You should be able to at least find a sweeter spot.
You may even have to go to 2T and non aggressive settings.
Why would the timings work when in single channel mode, but not in dual channel, when the Crucial memory works fine in dual channel at the same timings used in single channel?
On a side note, the Kingston pair was purchased together in a matched set, while the 2 Crucial sticks (actually the memory from my system) were bought seperately over a month apart.
The timings that RZT tried are the exact ones Kingston specifies for that model, there should be NO reason whatsoever they wouldn't work at those timings, dual or single channel.
Please correct me if I am wrong...
First of all, I said "in the meantime," meaning until someone else came up with a better answer. If I have problems with memory, regardless of what the manufacturer says' I hunt for a sweetspot (if there is one).
Quote
Why would the timings work when in single channel mode, but not in dual channel, when the Crucial memory works fine in dual channel at the same timings used in single channel?
That's like trying to compare apples to oranges. Two different manufacturers and likely different chips onboard, not to mention likely different PCB design.
What I suspect is either one stick is further out of spec than the other and they are not a properly matched pair. Kingston has a history with the nForce chipset which leaves little to be desired.
That is why you might see very similar systems, and one works with the same ram, and the other doesn't. It's called parametric differences. In short, one stick my be at the upper end of the spec and the other stick may be at the lower end. Then, throw in the motherboard, and the CPU, (now with the onboard memory controller) while we're at it, and you have a real touchy situation. There is little room for lower quality. That is why matched pairs exist. Doesn't mean it's mandatory, however.
Quote
On a side note, the Kingston pair was purchased together in a matched set, while the 2 Crucial sticks (actually the memory from my system) were bought seperately over a month apart.
I take it you know this person, otherwise this is not making sense or you are a pretty slick hijacker
Matched set can still be flawed, I get em from the best once in a while. It may not be the RAM at all. Only way to tell for sure is to try it on another identical system or try another pair that passes muster in another identical system. All this speculating is useless unless you've exhausted all possibilities.
Quote
The timings that RZT tried are the exact ones Kingston specifies for that model, there should be NO reason whatsoever they wouldn't work at those timings, dual or single channel.
Please correct me if I am wrong...
Not wrong, maybe a little overoptimistic. Some situations warrant different measures. It's not that black and white, nor is it written in stone. At this point it only indicates there is indeed a problem, where it lies, would be better off using a dartboard to guess at this point.

K8N Neo2 Platinum + Winchester 3200.. flabbergasting FSB issue

OK, here goes the issue:
I just got a brand new K8N Neo2 Platinum - Bios 1.4 and a box 3200 Winchester CPU. The crazy thing is the FSB - it is set to 200 Mhz in the Bios, but in real-time it happens to be something like 200.95 Mhz. No idea how to fix this - as a result the CPU goes at 2010 Mhz, while obiviously it should run at 2000Mhz. There are also some stability problems, like random hangups in Windows. My ram is 2x512 Kingston HyperX PC4000.
Thanks in advance for any suggestions.

Also about your "hang up" deal... Post more detailed specs on your system - You'll get better help that way.

Sound Issues /w K8N Neo2 Platinum

Hello, I have a K8N Neo2 Platinum and I am having trouble wit the sound. I have installed the drivers on the nForce CD, but I cannot hear anything.
Any suggestions?

You should list what opperating system you're using aswell as the driver version that's giving you trouble, someone might spot a problem and be able to help you more easily, for instance if you're using XPx64 the drivers for XP wont work.
Maybe try downloading the latest version from Here or Here.
Also check in Device Mannager, does it say that there's a problem with your sound device or does it say it's working properly ?

K8N Neo2 Platinum Ordered - Advice for a noob please

Hi there,
this seems like a great forum, was hoping someone could give me some advice - Im trying to pre-empt any major probs....
I am a relative noob to building P.C's - done a few P4 based systems before but this will be my first Athlon based. This systems primary use will be gaming. I have the following on order (should be with me next week) : -
a) MSI K8N NEO2 Platinum Edition SCK 939 Motherboad
b) AMD ATHLON 64 3500+ 64bit SCK 939 Retail Inc Fan
c) 160GB Maxtor Calypso 8mb Cache 7200 SATA DHH
Components I have already
a) Graphics Card - Nvidia 6800 GT
b) Memory - Generic 2 X 512MB PC2700 DDR333 RAM
c) Sound Card - Creative SB Live Value
d) PSU - Jeantech 450W (22a on 12V Rail)
e) Case - pretty generic full tower case - no fans attached
f) CPU FAN - COOLERMASTER HYPER 48 SUPER SILENT HEATPIPE
g) Spare Hard drive - 120GB Maxtor IDE Hard drive
h) DVD Drives - 1 x Pioneeer 108 / 1 x Pioneer 104
I) Monitors - Ilyama 17" TFT & Toshiba 32WL36P LCD
I have some 'noobish' questions - apologies for my ignorance : -
1) Memory - Will my memory be okay ? Should I ditch it and buy some Corsair DDR400 (which everyone else seems to have!). Will performance suffer if I stick with the DDR 333 ? Do I need to adjust settings in BIOS regarding memory timing ? (I only picked up on this from reading through other posts on this board, and am totally clueless on 'timing'- Ive never needed to adjust timing on any previous PC's....!)
2) Sound Card - will I be better off sticking with the onboard sound on the MSI K8N neo 2 ? Or for best performance do I go with the SB LIve ? (god its a nightmare trying to get updated drivers for this card), Would I get a noticable performance increase buying an Audigy 2?
3) Vcore / other power issues - Reading this forum Im kinda scared by many posts along the lines of "..for stability I need to change my memory voltage to xx-V" or "...for a stable system I needed to change my Vcore to xx-V". Will I need to change the Bios default values on this system just to get it to run stably??
4) CPU FAN - Are AMD stock fans any good ? My Hyper 48 is quite highly rated....
5) Im completely new to SATA drives, but Ive printed off the very useful install guide on this site (which I intend to use). Is there anything I need to look out for concerning adding my IDE drive also.
I think thats about it just now - if anyone can see any other potential problems with my specs then please let me know. Im really not trying to be negative / pessimistic - after all the reason I have went for this motherboard is that it is rated as one of the best. Im just a bit paranoid that the dreaded B.S.O.D awaits me!
On a more positive note - does anyone have similar system specs they use for gaming ? How well does HL2 / Doom3 / Farcry etc fly J ? I cant wait !
Thanks for the time

you may find these helpful
Overclockers Uk Power Supplies
This Week Only Enermax Noisetaker 485W EG495AX-VE(G) SFMA ATX2.0 PSU (CA-007-EN) Might be tempting
Scan International Power Supply

System suddenly won't power on (MSI K8N NEO2 PLATINUM NFORCE3)

System specs are
COOLERMASTER TAC-T01 WAVE MASTER ALUMINUM ATX 4X5.25 1X3.5 4X3.5INT case
MSI K8N NEO2 PLATINUM NFORCE3 ULTRA S939 AGP 5PCI SATA 1394 SOUND 1000LAN
KINGSTON HYPERX 1024MB DUAL CHANNEL KIT PC3500 2X512MB DDR 433MHZ 184PIN
ATI Radeon X800XT PE AGP
SEAGATE BARRACUDA 7200.7 200GB SATA 8MB 7200RPM 8.5MS OEM
CREATIVE SOUND BLASTER AUDIGY 2 ZS 7.1 1394 PCI RETAIL BOX
LITEON 16X DVD-ROM INT E-IDE RETAIl
MITSUMI FA404A 7-IN-1 FLOPPY DRIVE & FLASH READER CF/SM/SD/MMC/MS
LG 4163b dvd burner
Nothing has ever been overclocked on this system.
Everything is plugged into a Belkin Surgemaster powerbar.
I haven't mentioned the power supply. I'll get to that. I have been using an ANTEC NEOPOWER 480W POWER SUPPLY (ATX12V DUAL 12V RAILS ACTIVE PFC W/ DETACHABLE OUTPUT CABLES) for about a year on this system without
any issues. One morning, I wake up, hit the power button on my coolermaster case, and nothing happens.
CPU fan won't even spin. Nothing happens.
O.k., blown power supply, I think . . . .
So I take out my Antec and put it in another system. That system turns on
without any problems.
Hmm . . .
I come here, and I read posts about
potential compatibility issues with Antec power supplies. But if it's a compatibility
issue why was my system working for about a year?
O.k., fine. I'll buy a Enermax 535W EG565P-VE FMA 24P (115/230 VAC) power supply.
I just plug it into the mainboard (nothing else). Hit the power button . . .
The CPU fan spins for half a second, and then nothing.
Did my motherboard just suddenly die for no reason?
Any suggestions?

Pull the AC plug from PSU and set cmos in clear position with battery removed for atlest 20 minutes perhaps longer .
Then try to post the system barebone .
Just cpu,1 pcs memory in slot 1 , gfx card , and keyboard in PS2.
No usb devices at all including card reader and no pci cards harddisks or cdoms/dvd/floppy.
It could also be caused by a short or a malfunctioning fan connected to mobo.
Try to disconnect all case fans from mobo headers if you have any connected to additional fan holders.
The chipset fan can also be disconnected momentarily just to see if it posts.
If none of this helps , replace cmos battery and try again .

Which power supply for k8n neo2 Platinum

I need to buy a new power supply for my computer. With the ATX12V v2.2 standard and ATX12V 2.01 and the "no -5v on new psu's" issue I'm at a loss as to what to look for. I have looked and cannot find what "standard" (is that even the correct term?) the k8n neo2 supports.
My main requirement is that the psu be 550-650 watts and have modular cables. I know someday I will have to upgrade my system to PCI-E and modern components, so I would like a PSU that would work now and in the future.
Could someone point me in the right direction?
Many thanks
system spec's
Motherboard- MSI K8N Neo2 Platinum
CPU- AMD Athlon 64 X2 Dual core 4800 939 socket
Memory-CORSAIR 2X1G Twinx2048
Video- ATI HIS 4670 1GB AGP
HD- Seagate 100 gb 7200 rpm
Drives CD-DVD and CD-RW
PSU- Ultra X Connect 500W ATX
Sound- Creative SB Audigy2 Gamer
OS- WinXP Home SP3 32 bit

Why do you need 550-650W or is that just because of future needs? I would suggest one of the Corsair +12V single rail modular PSU's if you insist on the modular design. Check newegg for what they have for modular in the Corsair lineup. I'm sure you're aware that their price is considerably higher than the non-modular. K8 MB's that needed -5V are the early ones that had Creative Sound Blaster onboard audio.
HX650
   * Was: $139.99
   * $109.99
   * After $10.00 Rebate
   * $10.18 Shipping
That's what it is now but if you don't need it in a big hurry you can probably wait a while and get for the same price but with free shipping.
Edit: Gee, Ultra with blown caps, I just happen to have a xPRO 800W that blew some caps, repaired it and started going bad again and then got my TX650 to replace it. Got it for $70 after rebate (which I haven't received yet) by waiting for the right price, rebate and free shipping. VX550 would have been good enough but at the time I got the TX650 at a lower price.

Serious K8N Neo2 Platinum Problem

Hello
This is my long and sad story with this MSI board...
As I mentioned above, I have a K8N Neo2 Platinum with a Athlon64 3500+ (130nm) and some Corsair TwinX 3200XL 2x512 MB. The recommended setting for this Ram is 2-2-2-5-T1, but with this setting, my system crashes in prime 95 after maybe 5 mins and under compiling a Gentoo-System. But on the other hand, Memtest 86 reports no error at all with this timing. Later I changed the Timing to 2-2-2-5-T2 and suddenly, everyting becames stable. I could compile two Gentoo systems (32 & 64 Bit) and ran prime 95 for more than 24 hours. I have nothing overclocked. I think the Board is the Problem here, because there are some other malfunctions. Sometimes it doesen't detect my IDE Devices at startup (DVD-Rom and CD-rw) or my ethernet card gets no connection, but everything is configured well. So I really dont know what to do. I feed my Memory with 2.75 Volt. I also flashed the mainboard to Bios-Version 1.3 but nothing changed...
I hope anyone of you can give me a hint or something...
Thanks a lot

corsair ultra-low latency requires 2.75V according to their documentation. Also I have heard that prime95 has an issue with systems with 1024mb or ram in a certain test. Not sure I can't confirm but I do remember reading that somewhere yesterday.

Slow RX53, K8N Neo2 Platinum system

I put together my FX53 system last night. It is replacing a 1 year old P4 3.2 (Oc'd to 3.4) system. Basically I just replaced the CPU and MOBO and everything else is the same. Here are My specs.
Athlon FX53 939 pin
MSI K8N Neo2 Platinum
512 X2 Mushkin Level 2 DDR3500
EVGA GeForce 6800 GT (in the queue to upgrade to an Ultra)
SB Audigy ZS
2X Hitachi Deskstar 200GB RAID 0
PC Power and Cooling 510 watt PSU
CD burner DVD burner etc.
The installation and setup went perfectly. I have my RAM in slots 1&2 and it is reported as Dual Channel 200mhz. I did a fresh install of Windows XP sp2 and installed the latest (5.10) Nvidia chipset drivers and video drivers. My BIOS is basically set to "optimized defaults" (cool-n-quiet and the hardware devices I don't use are disabled). I just wanted to do some testing with untweaked settings to see just how much faster this system is than my old one. Much to my suprise it is slower, not a lot slower, but slower. I'm sure it should be faster. I lost about 6-8 FPS in Doom 3, and 3DMark 2003 lost about 800 points.
My Sandra scores are
Memory 5829
CPU 11067
Multimedia 22975/24465
3D Mark 03 is 11,421
CPU-1059
As far as I can tell my CPU/Memory benches look ok but not outstanding for my system. When you throw my Video card into the mix though my performance is less than expected. I'm stumped and disappointed. I feel like I payed almost $1000 for a downgrade.

512 X2 Mushkin Level 2 DDR3500
I had the same ram and both my co and cg HATED it. I ended up replacing it with 2x512 pc4k crucial ballistix. My A64's love my ballistix. 245 1T 2.5/2/2/6 2.8v or 265 2T 3,3,3,8 2.8v.
I personaly do not use memtest for testing A64's. It been my experience that memtest will miss errors which are detected by Goldmemory.
Try setting 2,3,2,7 and bump vdram to 2.8-2.85-2.9v. The level two has winbond BH-5 chips and they crave voltage.
Below is Mushkin's take on the a64's mem controller.
http://www.mushkin.com/epages/Mushkin.storefront/4156cad701e46ffc2741c0a801020673/UserTemplate/27
Quote
Athlon64 3000+ and Higher
The Athlon64 itself uses a single memory channel and only one controller on the CPU. Because of this, the Athlon 64 (non-FX) can actually use plain vanilla, unbuffered, non-ECC modules. There are, however, still some peculiarities of the Athlon64 systems in how they are handling memory which effects memory compatibility.
One of the most critical issues in this resepect relates to the first step in the memory access sequence, that is, the opening of a memory page and subsequent steps until a read command can be issued. All of these steps fall into the time frame referred to as RAS-to-CAS delay or tRCD. In a typical system, the memory controller on the chipset is running at bus speed. On the Athlon64, it is running at CPU speed, which means that it is A LOT faster. That means that the internal sequence of commands also goes faster, and that's where all systems are getting hiccups if the memory chips used can only run at a high tRCD.
A very trivial explanation is that the controller expects that the memory is as fast as it itself but we don't have memory yet running at a 2 GHz and beyond clock rate. What it comes down to is that, depending on the BIOS tuning (by the manufacturer), the read command is issued a bit too early and violates the tRCD. The workaround is to add one additional cycle to the actual memory latency, that is, a 2:2:2-rated DIMM will run stable at 2:3:2; a 2:3:2 rated module will, most likely, need to be set to 2:4:2 in order to run stable (where the latencies are CAS:tRCD:tRP). Bottom line is that when shopping for memory for the Athlon64, it is highly advisable and in most cases mandatory to only consider memory with a tRCD of 2 or, to make it simple, memory that is rated at 2:2:2 a the designated speed. Alternatively, registered DIMMs can be used as well without problems, even though they are slightly more expensive and will give lower performance.

K8N Neo2 Platinum 54G BIOS problem

I recently bought a MSI K8N Neo2 Platinum-54G mainboard with W7025NMS v1.3 092204 revision of BIOS.
AMD Athlon64 3000+ 939 is installed on the mainboard, with 2x512 GEIL PC3200 memory modules in dual channel configuration working on default frequency of 200MHz. CPU is recognized correctly as AMD Athlon64 3000+ on startup.
Mainboard’s BIOS seems to be corrupted. In Cell Menu options, in the upper left part of the screen (printed blue) are processor and DDR working timings:
Current CPU Clock 1810MHZ, Current DDR Clock 200MHz.
Aggressive Timings and Dynamic Overclocking values are [Disabled] (processor working on its defaulf settings); Spread Spectrum is [Disabled] while all DRAM Configuration settings are set to [Auto].
While entering HT frequency settings, (locked to [x5]) there are no other values to select – empty, and there is no way to leave it (ESC doesn’t help, the only thing possible to do is to reset the computer by pressing the Reset button on the chassis), but the HT frequency settings were enabled when I loaded Fail-Safe settings, offering [1x], [1.5x], [2x], [2.5x], [3x], [4x], [5x].
Adjust CPU Ratio settings offer only [StartUp], [x4]~[x9] values, but as I understood by reading the manual there should be [StartUp], [x4]~[x20].
CPU Voltage, Memory Voltage and AGP Voltage are set to default.
CPU-Z, as well as SiSoft Sandra 2004 and SiSoft Sandra 2005 and MSI CORE CELL show that processor works at a core speed ~1005MHz, showing multiplier locked on x5.0 and HTT locked at ~200MHz, while the voltage is ~1.05V!
I downloaded the latest BIOS revision (v1.4), did the BIOS flash, but the problem remains!
Anybody, help!

Quote
HT frequency
is a known fault in bios & is easily sorted Bas HT Bios Error
Quote
CPU Ratio settings
AMD64 CPOU's have a lock on CPU ratios which varies according to the specification of the chip. therefore the multiplier available in your bios stops at the max multiplier allowed by amd for your cpu.
As an example i'm running a 3200 754 which has a maximum muliplier of 11 so that is the max i see in bios.
this guide may help Bios Guide

K8N NEO2 Platinum rebooting

Hi all,just got myself a 64bit MSI K8N NEO2 Platinum board & a 3200+,am happy with it but a couple of days ago i got a blue screen with a long message that i didnt have time to read before the pc rebooted,after the reboot i checked the event viewer log file in administrative tools/control panel but couldnt narrow it down as my particular error code wasnt among the possible causes.
Among some of the possible causes were incorrectly installed USB drivers or the BIOS,i downloaded the latest BIOS update before this problem started(V1.40) which i am using now,i used the MSI live update software to flash it which i did in windows mode.Sorry for prattling on!well it did it again tonight and i managed to read a bit of the writing on the blue screen which mentioned flashing the bios to the latest version.I was wondering if anyone else is having the same problem and if so could you please advise me? Thanks for your patience and any help Heres my sys specs:
Model: AMD Athlon(tm) 64 Processor 3200+
Speed: 2.01GHz
Model Number: 3200 (estimated)
Performance Rating: PR3015 (estimated)
Type: Standard
L2 On-board Cache: 512kB ECC Synchronous Write-Back (16-way, 64
byte line size)
Bus(es): ISA AGP PCI USB FireWire/1394
MP Support: 1 CPU(s)
MP APIC: No
System BIOS: Phoenix Technologies, LTD 6.00 PG
Mainboard: MS-7025
Total Memory: 1023MB DDR-SDRAM
Model: Micro-Star International Co Ltd (MSI) ???
(00E1)
Front Side Bus Speed: 1x 201MHz (201MHz data rate)
Model: Advanced Micro Devices (AMD) Athlon 64 /
Opteron HyperTransport Technology
Configuration
Front Side Bus Speed: 1x 201MHz (201MHz data rate)
Total Memory: 2048MB DDR-SDRAM
Memory Bus Speed: 2x 201MHz (402MHz data rate)
Monitor/Panel: CTX EX950F series
Adapter: RADEON X800 Series
Adapter: RADEON X800 Series Secondary
Removable Drive: Floppy disk drive
Hard Disk: Maxtor 6Y080L0
CD-ROM/DVD: HL-DT-ST DVDRAM GSA-4081B (CD 32X Rd, 24X Wr)
(DVD 4X Rd, 3X Wr)
CD-ROM/DVD: MSI CD-RW CR52 (CD 40X Rd, 52X Wr)
CD-ROM/DVD: AXV CD/DVD-ROM SCSI CdRom Device (CD 32X Rd)
(DVD 4X Rd)
1.44MB 3.5" (A:): N/A
Hard drive (C:): 76.3GB (51.9GB, 68% Free) (NTFS)
CD-ROM/DVD (D:): N/A
CD-ROM/DVD (E:): N/A
CD-ROM/DVD (F:): N/A
Serial/Parallel Port(s): 1 COM / 1 LPT
USB Controller/Hub: Standard OpenHCD USB Host Controller
USB Controller/Hub: Standard OpenHCD USB Host Controller
USB Controller/Hub: Standard Enhanced PCI to USB Host Controller
USB Controller/Hub: USB Root Hub
USB Controller/Hub: USB Root Hub
USB Controller/Hub: USB Root Hub
FireWire/1394 Controller/Hub: VIA OHCI Compliant IEEE 1394 Host Controller
Keyboard: Standard 101/102-Key or Microsoft Natural PS/
2 Keyboard
Mouse: PS/2 Compatible Mouse
Device: Creative SB Live! series
Device: Creative Game Port
Model: EPSON Stylus CX3200
Windows System: Microsoft Windows XP/2002 Home (Win32 x86)
5.01.2600 (Service Pack 2)
Network Drivers Enabled: Yes
Warning 100: Large memory sizes should be made of
Registered/Buffered memory.
Tip 101: Large memory sizes should be made of ECC/
Parity memory.
>
>
Device Type: VGA Video Adapter
Device ID: bus 1, device 0, function 0
Windows Device Name: RADEON X800 Series
OEM Device Name: ATI Technologies ??? (4A49)
OEM Hardware ID: FUN_0, VEN_1002, DEV_4A49, REV_00
Device Name: PC Partner Ltd ??? (4A49)
Product ID: VEN_174B, DEV_0D42
Revision: A / 1 (0)
Version: 3.00
Command Queue Length: 256
Fast-Writes Support: Yes
Over 4GB Addressing Support: No
Isochronous Mode Support: No
Addressing Support: 32-bit
Data Transfer Modes Support: 4x 8x

My K8N Neo Platinum [754] did not include a NB fan. But this usually means the overall size of the heatsink is larger. If you remove the fan from yours, the size of the heatsink will not be big enough to cool your NB. As for temps, I've never seen my NB get hotter than 45'C. Note that the core on my NB should be slightly different than yours.
You could try to use the BIOS fan control for the NB. If set correctly, it should reduce some noise.

Need help with k8n neo2 platinum

I've just installed a new k8n neo2 platinum s939 board with a venice core 3200+ cpu the htt is 2000 and multiplier 10x.
I've gone to the core cell menu and set the htt to 4x (seemed to be this at default) and the max mem clock at 166 (more about this in a moment), the fsb will go quite easily up to 250mhz even 255mhz, but when I try 260 Mhz the machine when it reboots shows the initial slash screen but then goes to a blank screen with the cursor flashing in the top left hand corner, I can't even get back into the bios setup without clearing the cmos.
The odd thing is that the adjust cpu vid is showing a voltage of 1.50 and not 1.40 or startup.
Anyway with the fsb at 250mhz the bios screen is showing the Current ddr clock at 208 mhz ( not the max memclock setting of 166) the memory in the motherboard ( a crucial 512meg ddr333 single stick) seems to perform OK according to memtest which shows no errors after 2 cycles.
Any attempt to get to 260mhz fsb appears to fail even by upping the cpu vid to 1.525v unless i adjust the cpu voltage setting which by default is set to (by cpu vid) to +3.3%. Doing this enables me to get to fsb 260mhz but the memtest fails ( even when I set the max memclock to 133, which shows my current ddr speed at 174mhz, well below the 208mhz which appeared stable with the fsb at 250mhz?)
So firstly why are there two cpu voltage settings in the bios when my manual only shows 1 (there is no mention of this cpu vid setting?
How is it that my memory is stable at 208mhz with a fsb of 255mhz but unstable at 174mhz with the fsb set at 260mhz?
Why does the memory clock lock not appear to be working, the memory should be fixed at 166mhz but infact increases with fsb?
I have bios revision 1.5.
Please help as I am not familiar with the bios settings for this nforce 3 chipset, they seem rather odd to me. I'm sure my venice core 3200+ cpu can get beyond 250mhz fsb, I have another pc with a venice core 3000+ cpu which runs quite happily at 270mhz fsb.
PS I've tried reducing the htt to 3x but the same thing happens.

OK further feed back, I can get to over 260mhz fsb but the system is not stable the memory runs OK with mem test but I have problems with prime95.
I had to up the cpu core voltage to 1.53v to get to 260mhz using the cpu voltage setting in the bios and setting a 5% increase. increasing the cpu vid setting to 1.55v did not seem to do anything at all the core voltage was still at 1.43v.
I upped the mem voltage to 2.6v from 2.5 but still could not get the system to be stable, it may be that the memory is holding the system back but I don't want to pay for better memory at the moment. Unless anyone has got any other ideas it looks like I may be forced to settle with 250mhz, well still a 500mhz increase maybe not that bad. I've now to try 3d benchmarking using my radeon 9600xt and 3dmark 03.

USB Keyboard (K8N Neo2 platinum)

motherboard k8n neo2 platinum, somehow my motherboard does not recog my usb keyboard. i have gone to bios and enabled USB mouse/keyboard , my mouse is ok no matter which usb front or back but the keyboard usb does not work on any of usb . does anyone have any idea (hardly used keyboard, nearly new) all usb are ok??. your help will be much appreciated.
1-Motherboard MSI 7025 K8N Neo2 Platinum Chipset nForce3-250Gb/Ultra
2-CPU AMD Athlon Dual Core 3800X2
3- Graphic card (MSI FX5700) nVIDIA GeForce FX 5700
4-Memory 2 X1 GB DDR 400 DIMM kingston
5-HDD Maxtor 6Y160M0 (160 GB, 7200 RPM, SATA
6- OS Window XP Prof sp2
7-power supply Be Quite BQT- P5-420W

Bosskiller thanks for the reply it is a micorisoft multimedia, yes i have tried the back usb no luck there either. here is the link for the keyboard
http://www.farassoo.com/product/keyboard/fcr-8800.htm
but i wonder if you can tell me why some system their front usb doesn't work with usb keyboard a few have said this to me. many thanks

Problem on boot MSI K8N Neo2 Platinum

I am an italian lover of MSI motherboards.
After I bought a MSI KT3 Ultra Aru, then MSI K7N2 Delta ILSR and now I have a K8N Neo2 Platinum.
My hardware are:
MSI K8N Neo2 Platinum
Athlon 64 3200 Winchester
Corsair XMS 1024 TWINX 3200 PLL
Maxtor Diamond Plus 9 80 Gb
Asus Radeon 9600XT.
The problem is that at the power on the bios don't start. The LED on D-Bracket are three green and one red. On the manual this error are written:
Inizializing Video Interface
This will start detecting CPU clock, checking type of video onboard. Then, detect and initialize the video adapter.
This problem is frequent for my motherboard. However not always.
I attend your answer for this problem.
Thank you for all and for my english school.

Hi Italiano,
Welcome to the forum.
Have you details of your power supply. please show Maximum 3.3v,5v & 12v.
These are usually on the side of the power unit.
try:-
1) Enter bios Cell Menu - HT change from 5 ---> 4 using +/- keys. Save & exit.
If it still doesn't boot try:-
2) Re-inserting your Asus Radeon 9600XT. Sometimes they don't go in correctly.
3) See if you can boot with just 1 memory module in slot 1.
Luck

K8N Neo2 Platinum Memory Issues

Similar Messages

Maybe you are looking for