K8N Neo2 Platinum resets overclock....

Hello
K8N Neo2 Platinum resets my overclock to default speed when waking up from sleep... the overclocking is done solely in bios.
I have a Winnie 3200+ running @ 2.4Ghz with 1.45V .. when waking up .. the Vcore remains the same but the clock sets itself to 2.0Ghz.
What am I doing wrong .. or it is something wrong with my board.
Thanks in advance.

Sorry about asking a stupid question.
Quote from: the_cultie on 25-May-05, 17:50:12
Are you using CoreCenter to overclock? What version is your BIOS? Post system specs.
Quote from: tahuru on 25-May-05, 14:24:45
the overclocking is done solely in bios.
Anyway, there seems to be different problems relating to waking up from sleep, I know that Cool'n'Quiet would stop working when I would wake up from sleep. I'll try overclocking mine a bit and I'll get back to you.
Also, check that the Save/Clear CMOS jumper is in the right position.

Similar Messages

  • MOVED: K8N Neo2 Platinum resets overclock....

    This topic has been moved to Overclockers & Modding Corner.
    K8N Neo2 Platinum resets overclock....

    Sorry about asking a stupid question.
    Quote from: the_cultie on 25-May-05, 17:50:12
    Are you using CoreCenter to overclock? What version is your BIOS? Post system specs.
    Quote from: tahuru on 25-May-05, 14:24:45
    the overclocking is done solely in bios.
    Anyway, there seems to be different problems relating to waking up from sleep, I know that Cool'n'Quiet would stop working when I would wake up from sleep. I'll try overclocking mine a bit and I'll get back to you.
    Also, check that the Save/Clear CMOS jumper is in the right position.

  • MOVED: K8N Neo2 Platinum overclocking problem

    This topic has been moved to Overclockers & Modding Corner.
    K8N Neo2 Platinum overclocking problem

    Quote from: Sharp on 24-April-05, 06:04:48
    Hello,
    In the BIOS you must set the FSB:DRAM ratio to 1:1.
    Set the HTT (hypertransport Ratio to x4)
    Set the CPU ratio to x4 (just too see if it will work.)
    Set the FSB to 250Mhz
    Set the Vcore to 1.45v.
    Set the memory timings to SPD (or default values for DDR500)
    Set the memory voltage to 2.7v, 2.75v or 2.8v.
    Save and exit
    Then let it boot from the memtest bootdisk.
    Use memtest to see if it is ok, test for a long time, over 1 hour.
    http://www.memtest.org/download/1.55.1/memtest86+-1.55.1.floppy.zip
    Tight timings and high FSB is even better 
    I have the same problem I can go as high as fsb 219 without tweaking anything but the FSB. My system is about the same only my ram is ddr 400 so what should my mem volt and timg should be set to?

  • K8N Neo2 Platinum 54G BIOS problem

    I recently bought a MSI K8N Neo2 Platinum-54G mainboard with W7025NMS v1.3  092204 revision of BIOS.
    AMD Athlon64 3000+ 939 is installed on the mainboard, with 2x512 GEIL PC3200 memory modules in dual channel configuration working on default frequency of 200MHz. CPU is recognized correctly as AMD Athlon64 3000+ on startup.
    Mainboard’s BIOS seems to be corrupted. In Cell Menu options, in the upper left part of the screen (printed blue) are processor and DDR working timings:
    Current CPU Clock 1810MHZ, Current DDR Clock 200MHz.
    Aggressive Timings and Dynamic Overclocking values are [Disabled] (processor working on its defaulf settings); Spread Spectrum is [Disabled] while all DRAM Configuration settings are set to [Auto].
    While entering HT frequency settings, (locked to [x5])  there are no other values to select – empty, and there is no way to leave it (ESC doesn’t help, the only thing possible to do is to reset the computer by pressing the Reset button on the chassis), but  the HT frequency settings were enabled when I loaded Fail-Safe settings, offering [1x], [1.5x], [2x], [2.5x], [3x], [4x], [5x].
    Adjust CPU Ratio settings offer only [StartUp], [x4]~[x9] values, but as I understood by reading the manual there should be [StartUp], [x4]~[x20].
    CPU Voltage, Memory Voltage and AGP Voltage are set to default.
    CPU-Z, as well as SiSoft Sandra 2004 and SiSoft Sandra 2005 and MSI CORE CELL show that processor works at a core speed ~1005MHz, showing multiplier locked on x5.0 and HTT locked at ~200MHz, while the voltage is ~1.05V!
    I downloaded the latest BIOS revision (v1.4), did the BIOS flash, but the problem remains!
    Anybody, help!

    Quote
    HT frequency
    is a known fault in bios & is easily sorted Bas HT Bios Error
    Quote
    CPU Ratio settings
    AMD64 CPOU's have a lock on CPU ratios which varies according to the specification of the chip. therefore the multiplier available in your bios stops at the max multiplier allowed by amd for your cpu.
    As an example i'm running a 3200 754 which has a maximum muliplier of 11 so that is the max i see in bios.
    this guide may help Bios Guide

  • K8N-Neo2 Platinum pauses for 25 sec at boot, nvatabus.sys the problem?

    All,
    After POSTing normally and starting to load Windows XP, my system halts at the Windows XP splash screen for about 25 seconds. Nothing happens, no disk activity or anything, the system just sits there.
    I used Microsoft's Bootvis utility to see what was happening. It turns out that the nvatabus.sys driver consumes 100% CPU at boot for 25 seconds then the system continues to boot normally. Does anyone else see anything like this?
    I am running the latest nForce drivers from MSI. The driver in question:
    NVIDIA nForce3 Serial ATA Controller 2.6
    Driver Date 6/3/2004
    c:\WINDOWS\System32\DRIVERS\nvatabus.sys 5.10.2600.0446
    Windows XP SP1
    I have a RAID1 of two 160 GB SATA drives. The mirror is healthy and working fine.
    After booting the system is rock-solid stable, no problems there. It's just this unexplained pause at boot. Does anyone have any ideas how to fix this?

    ok check it out guy's this thing drove me insane all night last night and most of today. I was ready to return everything and give up. But alas all is not lost. Here is the rundown on what i just did.
    My Equipment:
    Athlon 64 3800+(w/ stock fan)
    MSI K8N Neo2 Platinum Socket 939
    2X512 Corsair TWINX1024-3200XLPRO ( with the cool led's )
    2 SATA HD (1 Maxtor Diamond10 300 GB w/ 16mb cache, 1 Segate 160GB w/8mb cache)
    PP&C 425 ATX Deluxe
    Radeon 9700 Pro ( cat 4.8 )
    Audigy2 ZS
    Sony Floppy
    Sony 8x52x52x32 DVD Rewrite
    I have been reading and reading just like all you guy's. On a few websites i would pick up bits and pieces on what to try. Heres what i did. Upon Boot up i entered the bios. I then went to Cell Soft and adjusted my timings for my memory. I was at 2.5 not 2.75. I then set my speed down to 166. Exited and restarted. Big mistake everything ri=uns terrible slow and my expensive DDR 400 memory was showing up correctly at 333. Rebooted again entered the bios. reset my speed to 400. Then set the Overclock feature to manual. Set my timings at 2,2,5,2 200 and 2.75 volts. After saving settings and exiting I then turned off the computer. As per some other suggestions I moved my Audigy2 to the bottom most pci slot the one above the orange slot. I moved my memory to slots 2 and 4. I moved my SATA to slots 3 and 4. I rebooted went into the bios again and setup all my voltages. CPU was Auto, AGP was max yellow setting. Memory still at 2.75. I disabled the onboard serial and parrallel ports. Rebooted
    Fearing the worst,
    5 seconds, 10 seconds, windows screen loging prompt. There was nothing wrong at all. It rebooted effortlessly. It re found my Audigy card and wanted driver but that was it. I am going to reboot a few more times and then run sisandra to test. I hope some of this will help you. I post in a few after some of those reboots.

  • K8N Neo2 Platinum - satisfied except cold boot

    My new build is doing well except for the near-famous cold-boot problem. When the box has been off for a while, I hit the power button, fans & drives spin up, the optical blinks a couple times, but no video or POST. The LEDs look like 4 green, but 2 seem dimmer, as if they're just reflecting the light from the other 2. A 5-second hiit on the power button shuts it down, hit it again and it fires right up, but stops during post with the message that it's in safe mode and to reset my (nonexistent) OCs. From this point I can F1, boot up, and run for hours. No probs unless it's off for a while. I have seen the problem since early in the build, when I powered up outside the case with just 1 stick of RAM and the LEDs (no vid or drives).
    Searching the board shows a lot of people having the problem, but nobody seems to have a solution, so I went to the support site to check the knowledge-base and FAQs. Interesting to find there that A64 boards do not appear to exist. No FAQ, no option to spec socket 939 or 754 to search the KB.
    Maybe if we get a number of us with the problem to post specs & observations in one thread we can spot a pattern?
    I have noted that I can't just do an on-off-on. It has to spend 20-30 seconds in the lockup mode before cycling the power results in a successful boot.
    BTW all, some really nice things are happening with RAM prices lately. I got my 2 gigs for US$190 delivered.
    K8N Neo2 Platinum
    Athlon64 3500 (130 nm)
    2G (4 x 512) SuperTalent PC3200 RAM
    2 120G Maxtor SATA (1 & 2) in raid0
    1 160G Seagate SATA (3)
    1 Sony DRU 720A 16X dual-layer DVD +/- R/RW (primary master)
    PNY Verto nVidia 6800 vid
    Mad Dog 600W PSU (30A on +12)

    Quote from: elliott on 13-April-05, 09:23:05
    I'll give the bios a shot, but the idea of using the HT to slow the box down and then speeding it back up again in Winders...
    Putting HT to 4 does not slow down the box... Especially if ur FSB is over 200 (if ur overclocking) like in my case: FSB=260mhz, I must put down the HT to 4 in order to run everything perfect. HT standard is 200x5=1000, in my case its 260x4=1040... as long as HT is between 800-1200... I believe there is no real time performance loss as long as u have STABILITY. I have seen a lotta people in this forum fixing stability problems just by reducing the HT when they overclocking... some cases even to HT=3.

  • Reboot problem with MSI K8N Neo2 Platinum and 250 GB SATA HDD

    I'm having a "reboot" problem with my MSI K8N Neo2 Platinum. After turning my system on it will run without any problems, until I reboot. After a reboot it will always hang after the initial windows-bootscreen. The HDD-light will remain on. If, instead of going into Windows XP SP2, I try to enter the BIOS after a reboot (DEL) the system will also hang (blank screen with blinking cursor).
    It started doing this after I installed the Maxtor 250 GB SATA disk. Before, I didn't have problems rebooting. If I disconnect the Maxtor drive I can reboot and enter BIOS and Windows each and every time. Reconnecting the Maxtor 250 GB SATA drive will return the reboot problem. I always have to use the power swith to get a working system again. It's not enough to do a hard reset (this has the same effect as rebooting).
    Here are the details of my system:
    MSI K8N Neo2 Platinum (BIOS 1.B)
    Athlon 64 3200+ (Winchester, 2 Ghz, 512 KB cache, stepping DH-D0)
    2 x Kingston KVR400X64C25/512, 512 MB, DDR, PC3200 (2,5-3-3-8 T1)
    Asus Radeon AX800 Pro (256 MB)
    PSU Antec Sonata 380W
    HDD Maxtor 80Gb ATA (6Y080P0, Pri Master)
    HDD Seagate 250Gb SATA (ST3200822AS)
    HDD Maxtor 250Gb SATA (6V250F0 - jumpered in SATA150 mode, the mobo wouldn't work with the drive in SATA300-mode)
    Aopen COM5232/AAH Pro CD-Writer ATA (Sec Master)
    BenQ DW1640 DVD-Writer ATA (Sec Slave)
    P.S. The NVidia IDE-drivers are NOT installed. System is not overclocked.

    Thank you for all the replies. Upgrading to the latest Nvidia IDE-drivers did not fix my problem. Moving to other SATA-ports did not help either. Upgrading the mobo's BIOS is not really an option (I'm using one version before the most recent and there isn't anything in the fixlist of the latest BIOS).
    Now I've contacted Maxtor for (hopefully) a new firmware.
    Quote from: rogueUK on 31-July-06, 16:55:42
    insego please use the SEARCH BUTTON
    I did use the search function to find other people with similar problems. The reason I started a topic of my own was because of the text you get while joining:
    Quote
    Do not hijack another persons topic. If you have a similar problem, start your own thread anyway.
    Maybe in retrospect I should first have tried the solutions in other topics.

  • News - BIG PROBLEM - MSI K8N Neo2 Platinum - DOES NOT POWER!!!

    Hi to everyone.
    I'm a proudly owner of a MSI K8N Neo2 Platinum that in one year gave me no problem until yesterday morning.
    I used the computer in the night before and when I finished I turned it off and I went to bed.
    Yesterday morning I found the power led blinking (like if the system was in standby), and there was no way to turn the PC on.
    I even took off the battery for more than 12 hours and I left only minimal components installed:
    the video card (Gainward GeForce 6800),
    the psu (Antec TruePower 550W),
    1 x 512 MB Ram Crucial Ballistix,
    and I checked them into another computer and they work perfectly.
    I tried shorting the MB power switch pins with a screwdriver and I've even tried to power on the system without the Memory or the Video Card... I've tried everything that came across my mind with no efforts!!!!
    Every time I give power to the MB appens only that the power led starts blinking, but pressing the button the PC doesn't turn on.
    PLEASE HELP ME... I really don't know what else to do!!!
    Thanks,
    Alberto

    Quote from: alberto_melita on 20-August-05, 20:14:56
    Hi thanks for the answers.
    I do have a D-Bracket, but my problem is not that the system does not boot or does not post... my system DOES NOT POWER ON (!!!!), so d-bracket is useless!
    When I plug the system power    the only thing that happens is that the power led starts blinking (with the system still in soft-off), and if I press the power switch button nothing happens! 
    I've the bios for 7025 v1.8 and the settings where for OFF on power-loss ond pressing the button (can't rememeber if it was more than 4 sec) was meant to turn off the computer, but considering that I un-powered the pc more than once without the MB battery the settings should be factory default by now.
    I went through the Windows-XP shut-down system, and i could not be an electrical problem as I always used the PC with a pretty good UPS unit.
    Right now these are the full specs of my sytem:
    - MB MSI K8N Neo2 Platinum nForce3 Ultra
    - GAINWARD 6800 2600 GLH 256 MB Ram
    - PSU Antec TruPower 550 W
    - CPU AMD64 3500+ core Winchester @11*210 Mhz (this cpu has never overclocked very well)
    - HEATSINK Thermalright XP-90 with a 12 Cm Enermax Fan (CPU temp in always below 55 °C when stressed)
    - 1 x 512 Mb RAM Crucial Ballistix DDR400 optimized for  MSI K8N Neo2 Platinum
    I left only these things inside my computer in the hope that it would turn on... it did not work. I tested each component but the MB, and they work perfectly.
    Again...
    Thanks for you efforts, any help will be appreciated.
    Alberto.
    All parts have been tested: CPU/RAM/GFX/PSU/HD/DVD,  just not the MOBO ?
    Checked if the MOBO is shorting in the case ?
    Have you tried using the reset switch as power, on/off switch ?  I've seen before when the power switch stops working (lose/bad wire busted spring) after swapping  reset to power, then the system turned on. Worth a try, as sending it back to USA won't be cheap. If its over 1 year old it mite not be covered by the re-seller and or MSI. Best to check this out as law and warranty is different from country to country.
    Good Luck

  • System suddenly won't power on (MSI K8N NEO2 PLATINUM NFORCE3)

    System specs are
    COOLERMASTER TAC-T01 WAVE MASTER ALUMINUM ATX 4X5.25 1X3.5 4X3.5INT case
    MSI K8N NEO2 PLATINUM NFORCE3 ULTRA S939 AGP 5PCI SATA 1394 SOUND 1000LAN
    KINGSTON HYPERX 1024MB DUAL CHANNEL KIT PC3500 2X512MB DDR 433MHZ 184PIN
    ATI Radeon X800XT PE AGP
    SEAGATE BARRACUDA 7200.7 200GB SATA 8MB 7200RPM 8.5MS OEM
    CREATIVE SOUND BLASTER AUDIGY 2 ZS 7.1 1394 PCI RETAIL BOX
    LITEON 16X DVD-ROM INT E-IDE RETAIl
    MITSUMI FA404A 7-IN-1 FLOPPY DRIVE & FLASH READER CF/SM/SD/MMC/MS
    LG 4163b dvd burner
    Nothing has ever been overclocked on this system.
    Everything is plugged into a Belkin Surgemaster powerbar.
    I haven't mentioned the power supply. I'll get to that. I have been using an ANTEC NEOPOWER 480W POWER SUPPLY (ATX12V  DUAL 12V RAILS ACTIVE PFC W/ DETACHABLE OUTPUT CABLES) for about a year on this system without
    any issues. One morning, I wake up, hit the power button on my coolermaster case, and nothing happens.
    CPU fan won't even spin. Nothing happens.
    O.k., blown power supply, I think . . . .
    So I take out my Antec and put it in another system. That system turns on
    without any problems.
    Hmm . . .
    I come here, and I read posts about
    potential compatibility issues with Antec power supplies. But if it's a compatibility
    issue why was my system working for about a year?
    O.k., fine. I'll buy a Enermax 535W EG565P-VE FMA 24P (115/230 VAC) power supply.
    I just plug it into the mainboard (nothing else). Hit the power button . . .
    The CPU fan spins for half a second, and then nothing.
    Did my motherboard just suddenly die for no reason?
    Any suggestions?

    Pull the AC plug from PSU and set cmos in clear position with battery removed for atlest 20 minutes perhaps longer .
    Then try to post the system barebone .
    Just cpu,1 pcs memory in slot 1 , gfx card , and keyboard in PS2.
    No usb devices at all including card reader and no pci cards harddisks or cdoms/dvd/floppy.
    It could also be caused by a short or a malfunctioning fan connected to mobo.
    Try to disconnect all case fans from mobo headers if you have any connected to additional fan holders.
    The chipset fan can also be disconnected momentarily just to see if it posts.
    If none of this helps , replace cmos battery and try again .

  • K8N Neo2 platinum & 750g sata RAID issue

    Hi there I have an issue with booting up. I have 1 200g Western digital HDD where windows is installed and I have 1 further 500g WD drive which were both fine until I decided to buy 2 samsung 750g HDD's to run in RAID. I have installed the drives in RAID and formatted but I am having a problem with booting.
    If I reset, the computer keeps rebooting at the detection stage, powers off and keeps doing it over and over. Sometimes it will go through if you wait long enough. When I turn the power on and off it will go through the detection stage no worries every time but then at the XP loading screen it will freeze there. Sometimes it goes through and I will boot into XP fine and other times I can't get in.
    I have the latest Bios 7025V1D but I am wondering if this issue is bios related because of the 750g size... The problem has only started since I have installed the two 750g HDD's in RAID. Does this bios version support 750g HDD's? Is there an updated BIOS to fix this problem somewhere?
    I have 2gig of ram, 3500+ processor, latest Nforce3 drivers from Nvidia, RAID drives on sata ports/3/4, 500gig WD on sata port 1, 200 gig WD is HDD is IDE, Windows SP2 and all updated, ummmmmm everything else is fine I'm fairly sure.
    I had a few troubles installing the RAID drivers because windows didn't want to accept the drivers I downloaded from here and did not want to accept the drivers in windows. I ended up getting it the drives to come on-line through the use of START/NVIDIA corp/ NVIDIA RAID program (cant remember the name, typing this on another computer).
    Any ideas would be greatly and very muchly appreciated!
    Terry.

    Ok My PSU is: WideTECH 550w, +3.3v=33a, +5v=36a, +12v=25a, -12v=1.0a, +5vsb=2.5a.
    I am only running 3 HDD's at the moment, the 2 750's and the 1 200gig. I have left the other 500gig unplugged until I get this problem sorted. I don't have a cd rom plugged in or a floppy. I only connect them when I need to because this computer is setup to be a storage server and I use my other pc for anything dvd related etc. The only other thing which is chewing power is the video card which is an old 6800gt ultra. So basically the power issue was fine until I installed the two extra HDD's and as I have unplugged the 500gig for the time being its only really one extra HDD which shouldn't be an issue. Oh I have two 80mm case fans using the psu aswell.
    As for my other specs: I have 1 gig of Geil dual channel RAM 2x512 sticks, CPU=AMD Athlon64 3500+, MB is MSI K8n Neo2 Platinum, Vid card= Leadtek geforce 6800gt ultra 256 agp, You know about my HDD's but here they are again= 1x 200g WD caviar IDE, 1x 500g WD caviar sata(1 I think), 2 x 750g samsung sata (2 I think), OS = XP Home SP2 with all lasest automatic updates, latest BIOS etc etc etc....
    My windows is a legit copy as well.
    You mentioned putting my HDD's into sata 1 mode... I was of the opinion that my motherboard does not support sata2 anyway and would not allow them to run in anything but sata1?? If I did want to change the sata mode where would I do this anyway?
    Thanks for your reply but I don't think it has to do with psu or sata mode although I'm interested about this sata2 thing, please explain.
    Thanks in advance,
    Terry.

  • MSI K8N Neo2 Platinum cant upgrade to BIOS 1.4, Windows wont boot.

    Hello
    I have a MSI K8N Neo2 Platinum and I cant upgrade to BIOS 1.4.  I have tried everything and cannot get Windows XP to boot with BIOS 1.4.
    I have reset the BIOS, set defaults, cleared the battery etc but when I load BIOS 1.4 (from a 98SE an ME boot dish and even from the Live Update?
    The only solution is to rebuild Windows after loading BIOS 1.4???
    Help

    Hi !
    Well, I have that problem, too. I think the reason is a new RAID-BIOS-Version built in the BIOS-Update. I´ve tried the beta-versions V1.51 and V1.5X, too - but they won´t run anyway.
    My WinXp hangs while booting (before the WINDOWS-XP-Logo appears, or while fading in...). I cannot reinstall Windows completely because, when I install the 2 raid-drivers, the installation routine hangs before the licensetext - when I don´t install the drivers i cannont install on the raid-drive (beacuase the installation routine shows 2 hdds).
    I think, a new driver will solve this problem, but I don´t know where to find it....
    A.

  • K8N Neo2 Platinum - SATA1/SATA2

    I've seen some concerns on the forums about SATA1/SATA2 not being stable on this board.  Is this still a valid concern if I do not overclock my machine? I plan on using a 300GB SATA Seagate on SATA1 as a drive where I will store my backups.  I'll use an external USB 2.0 cabinet for the 300GB SATA drive if reliability is going to be a problem.
    Your thoughts are appreciated,
    Dan
    Athlon 64 3500+
    MSI K8N Neo2 Platinum
    2GB RAM
    ATI Radeon 9800
    SATA1 - 300GB Seagate
    SATA 3/4 - 120GB Seagate in RAID1
    IDE Primary - 250GB Hitachi
    IDE 3/4 - Plextor DVD-R
    Western Digital 74GB Raptor
    Antec True 430

    Quote from: Ayato on 21-June-06, 22:27:27
    I think all you said is very odd  as i've succeeded in o/cing my 3800+ x2 at 10 x 233 whereas i plugged my Western Digital serial ata Hdd on serial port 1, and i'm not running any instability pbs or overheats, am i lucky or is it due to the latest official bios version ??
    Then how long have you OCED it? but be aware then you might screwed it out but just in matters of time.  
    I agreed with Syar's explanations as ocing the system at that range may caused instability. However, I do experience on my own as I did screwed my HDD SATA WD where I've OCed at 225-230 my HDD is totally burn due to the OCing.

  • Msi k8n neo2 platinum and corsair cmx512-3200LL

    is anyone using the corsair cmx512-3200LL with the msi k8n neo2 platinum or any other motherboards? if so how well does that memory overclock for you?

    LL used winbond CH-5 or BH-5 or Infineon B-5 depending on revision .
    And everybody knows that it's hard to overclock winbond very far without excessive vdimm increase (2.9v - 3.4v).
    Corsair XL use samsung TCCD and overclocks much easier when having a motherboard with a vdimm limit at 2.85v.
    xms 4xxx also use samsung (TCCC or TCCD) and some versions use hynix D43/D5
    so you can't directly compare xms3200LL with the others .
    You can query RamGuy about the chips used on the spesific modules here :
    http://www.houseofhelp.com/forums/showthread.php?t=35940&page=1&pp=15
    Note the Part , version , and lot number before posting .

  • New to OC - a64 3200+ 939, MSI K8N Neo2 Platinum

    Dear All,
    First off.  I am new here so hi to you all
    I am new to overclocking.  Please tell me how far I can go for my CPU (RAM I don't plan to), and what settings in bios I need to change (in simple words, don't try me on abbrev too much :P)
    Spec:
    AMD Athlon 64 3200+ 939 Winchester
    MSI K8N Neo2 Platinum
    2x512 Samsung PC3200 DDR Dual Channel RAM (I don't plan to OC RAM)
    Antec TruePower 380W (Sonata edition)
    BFG GeForce 6800 OC (I don't really plan to OC that either, dunno how)
    Would I be able to up from 2.0ghz to 2.2ghz?
    Current CPU idle temp: 38 degrees (Arctic Silver 5 applied)
    Thank you!
    dL

    Quote
    Originally posted by dL.
    Temp at load (playing CS:S) is about 41-42 degrees.
    Idle is about 35-38. Temps look ok
    Will my Antec TruePower 380W power supply provide sufficient power when increasing vcore? Sjould do just fine Will increasing vcore damage anything? Not as long as it stays cool. How much should I increase it by? Just up a .05 at a time and test.
    Also, can I lower my HT to even lower like 3x to get more clock speed? Yes but X4 should be good up to 250. Youn need to keep it under 1000. 250 x4 = 1000
    dL

  • New CPU, Msi K8n neo2 platinum - no boot!

    Greetings!
    I got the following components:
    *MSI K8N NEO2 Platinum -54g MB
    *4 x 512mb Geil Value Ram
    *Gainward 7800GS+ Bliss 512mb AGP
    *Samsung Spinpoint 500gb SATA HD
    *Corsair 620HX (620W) PSU
    *CPU AMD Opteron 180 Dual Core (upgrade from AMD 3000+ Winchester)
    I recently upgraded my PC with a new HD, more ram, new CU Fan/heatsink - on an AMD 3000+ (Winchester). PC wouldn't boot - I did however manage to fix it. I think it was because of the ram, one of the bricks had some dust on it. Since then, my pc has worked 100%...
    Today, however, I got a new PSU and CPU in the mail! A Corsair 620W PSU and an AMD OPTERON 180 Dual. I carefully cleaned the surface on the heatsink etc, and applied an appropriate amount of "Arctic Alumina" on the CPU/heatsink (as followed per instructions from Arctic). When I have connected everything, and fire my pc up - it just won't boot.. (The monitor won't light up).
    Since then, I have carefully checked all wires, unplugged/replugged etc.
    But it just won't boot!
    I do have the latest bios (1.0D), so it should support my CPU.
    I should mention some "weird" things, though. When I try to boot up, everything seems normal (All fans are running), but there are no lights on my case! And I can't turn off the PC while holding down the "power" button on my case. I can't reset either.. as soon as I turn the PC on (by turning on the PSU power switch), the PC starts running. Normally I would have to push the button on my case. ALSO: I have cleared CMOS, still a black screen. And I have tried 2 different monitors, so I know it aint that either.
    My old PSU was a Chieftec 360W one (and my case is a Chieftec also). The old PSU was connected to "SFAN2" on my MB,.. my new PSU isn't connected to any "SFAN" at all.. I doubt that has anything to do with the problem though?
    Any suggestions on what I might do ?
    Edit: D-bracket shows this (Yellow, red, red, yellow):
    BIOS Sign On
    - This will start showing information about logo, processor brand name, etc... - It stops here. No boot screen

    Quote from: BOSSKILLER on 14-November-07, 21:14:42
    remove power cord from the PSU(else will not work) and Clear CMOS Guide.
    leave one memory stick only in a 1st DIMM slot near to CPU socket and try to boot.
    Done & done.
    Still no boot screen :(

Maybe you are looking for