K8N Neo2 Platinum wont post or boot (64 3000+)

After plugging in the computer and starting up, the fans run and the drives spin, but I get no boot or post and nothing to the monitor. I have tried just CPU and MOBO. Ive tried CPU, MOBO, RAM, Video (Radeon 9600 Pro), and all give me nothing. My two CD drives LED's blink and they constantly spin up over and over and over. The DLED's on the back WERE all red for a while. Now when I turn it on, LED one and two are red, three is orange ( not the red it used to be) and 4 isnt even on.
I was having problems with the computer after I would turn it off, and reboot, It would hang during post sometimes, and then I would reboot and everything would be merry.
I went on vacation, unplugged EVERYTHING, and then came back, plugged it up, and pressed the power button. Once again I saw the Platinum splash screen but it hung and didnt do anything else. I re-booted and had no video, and no post beeps. The drives spin up and down (optical) and will do it forever. I have no idea whats going on. First i thought it was the processor not running the BIOS, then I thought the DLED's looked weird so Im working if its not my motherboard.
The PS is a Antec SL400 400 Watt. About a year to a year and a half old. Memory is a year old. Processor is a year old. Ive removed everything and tried the test bench setup on a cardboard box outta the case and i get the same situation. Any help would be great. Thanks.

Quote from: ry_ry_us on 28-December-06, 09:48:35
Well I guess thats two problems. I feel like there is no need in investing in an outdated board and processor when i could be buyin a new one. IF there is no other way to see whats bad then I guess I may have to start a whole new build. Any other ideas? Why in the world are the DLED's acting weird?
you can borrow from friends to test it, or to take PC(case only) in some PC store/repair shop to ask for test there.
another idea is try to disconnect D-Bracket and retest.

Similar Messages

K8N Neo2 Platinum - satisfied except cold boot

My new build is doing well except for the near-famous cold-boot problem. When the box has been off for a while, I hit the power button, fans & drives spin up, the optical blinks a couple times, but no video or POST. The LEDs look like 4 green, but 2 seem dimmer, as if they're just reflecting the light from the other 2. A 5-second hiit on the power button shuts it down, hit it again and it fires right up, but stops during post with the message that it's in safe mode and to reset my (nonexistent) OCs. From this point I can F1, boot up, and run for hours. No probs unless it's off for a while. I have seen the problem since early in the build, when I powered up outside the case with just 1 stick of RAM and the LEDs (no vid or drives).
Searching the board shows a lot of people having the problem, but nobody seems to have a solution, so I went to the support site to check the knowledge-base and FAQs. Interesting to find there that A64 boards do not appear to exist. No FAQ, no option to spec socket 939 or 754 to search the KB.
Maybe if we get a number of us with the problem to post specs & observations in one thread we can spot a pattern?
I have noted that I can't just do an on-off-on. It has to spend 20-30 seconds in the lockup mode before cycling the power results in a successful boot.
BTW all, some really nice things are happening with RAM prices lately. I got my 2 gigs for US$190 delivered.
K8N Neo2 Platinum
Athlon64 3500 (130 nm)
2G (4 x 512) SuperTalent PC3200 RAM
2 120G Maxtor SATA (1 & 2) in raid0
1 160G Seagate SATA (3)
1 Sony DRU 720A 16X dual-layer DVD +/- R/RW (primary master)
PNY Verto nVidia 6800 vid
Mad Dog 600W PSU (30A on +12)

Quote from: elliott on 13-April-05, 09:23:05
I'll give the bios a shot, but the idea of using the HT to slow the box down and then speeding it back up again in Winders...
Putting HT to 4 does not slow down the box... Especially if ur FSB is over 200 (if ur overclocking) like in my case: FSB=260mhz, I must put down the HT to 4 in order to run everything perfect. HT standard is 200x5=1000, in my case its 260x4=1040... as long as HT is between 800-1200... I believe there is no real time performance loss as long as u have STABILITY. I have seen a lotta people in this forum fixing stability problems just by reducing the HT when they overclocking... some cases even to HT=3.

K8N Neo2 Platinum ed. XP Boot freese problem !!!

After the bios post screen, when the xp logo disappered, it's freese 2-3 minutes. XP starts normally and full functionally after the freese. I have no stability problem.
I have install XPSP2 ( SP2 embedded XP cd. Created autostremer) Install all latest drivers and bios update (1.B0)
I've use only one hdd, no raid array. I've try the bios settings optimized. Guided like this documents FAQ
Specially thanks for your interest
K8N Neo2 Platinum ed nforce3 ultra
AMD64 Athlon venice 3000+
sata1 Samsung HD080HJ SATA 80Gb
ide1 LG-DVD writter
MSI Geforce FX5200 AGP
2*256 Kingston DDR
No FDD
A4Tech keyboard and mouse PS2
CPU-Z Report CPUZ

Check eventviewer for drivers/sw thats fails to load .
Other than that most boot delay problems are related to bad IDE (master/slave) configuration or cables .

K8N Neo2 Platinum wont start up

After installing a new K8N Neo2 it worked perfectly for 1 day, no problems at all.
The day after nothing happened. When the psu is turned on it only gives a short flash on the leds, the fans turns for a second and then everything is of.
Have tried with only the most necessary connected to the psu, switched to only 1 RAM in different positions etc. Have cleared cmos every time.
D bracket leds are showing 4 reds for a short second and some times two greens diagonal upper left to lower right and the other two are red.
Any ideas???
Spec;
AMD Athlon64 3500+
K8N Neo2 Platinum
NX6800 Geforce 6800GT
WD Raptor 740GD 74G ( x2 )
Corsair CMX256A-3200LL ( x4 )
Antec True 480P ( 5V-38A, 12V-22A, 3,3V-30A )

Hi,
Its a common problem with this board... different theories are abound as to what causes it, an RMA might not help you
False Starts on MSI K8N Neo2 Platinum

K8N Neo4 Platinum Wont POST please help!!

ok, i built this pc about a month ago. everything has worked perfectly until yesterday. When i turn the power on, al i get is the Platinum Screen. I cant go into Bios, i cant Post.. The PC beeps once like normal, and the LED on the Motherboard and the videocard come on. Ive tried wiping the CMOS, Tried a different PSU, tried removing one of the memory sticks. I tried just connecting the Mobo, video card and harddrive, to see if it want getting enough power. Heres what ive got:
K8N Neo4 Platinum/SLI
Athlon 64 3500+
Geforce 6800 Gt
1 Gig corsair 3200 ram (2x512mb)
550 watt PSU

reset the bios, make sure its RESET.
then, try with just 1 stick ram first.
remember, to run dual for this board, it has to be Slot 1 & Slot 2.
If u follow the color, it'll be single channel instead.
Read also the instruction, it says never plug into 2nd or 4th slot with 1 stick ram.
Try with 1 stick ram. if it boots, then insert the 2nd into Slot 2. for dual channel.
i had similar prob few days back when newly purchased.
good luck !

K8N Neo Platinum wont POST - help!

I decided to flash my bios to the latest version, 1.4, and after it said it was completed and restarted my system would no longer boot. It runs for about 5 seconds then shuts down. I've tried the recovery with a floppy drive but my system doesn't even try to access the drive. I'm guessing I have to get an RMA, but does anyone know how to fix this?

Quote
Originally posted by TimKessler
Quote
I agree it's probably the PSU but what do we tell him when he spends $140 for an OCZ and still has the same problem?
I would suggest that he only pay around $85 for a trupower 480, which has been very solid and stable for me.
Coolmax 500wt is only $56 at Newegg and as 28amps on the 12v. Highly recommended.

K8n neo2 (s939) bios/post problems

hello guys
i hope you can help me out here
english is my second language so please bear whit me
first my specs in a nutshell:
k8n neo2 (s939)
amd64 3500
geforce fx5800
the problem is:
every time i turn the power off i need to flash the bios to get trough his post.
if i reboot from windows (not shutdown but reboot) then it runs trouhg his post normaly, but if i shutdown not.
it simply does nothing if i press the power botton.
on the d-bracklet i see 4 green or 4 red lichts so that must be wrong too i think right?
if annyone have a sulution: thank you verry much
ps: i am running bios version: 1.4

By flash the BIOS do you mean reset CMOS? i.e. you switch a jumper for a few seconds?
If so you have the same problem as me in this post: MSI K8N Neo2 Platinum wont boot without clearing CMOS first.
I changed the HT in BIOS to 4x and have been stable ever since.

K8N NEO2 PLATINUM ATA-133 Raid ?

Hello,
My question is, is it possible to setup an Ata-133 raid on the K8N NEO2 PLATINUM (as the main boot drive). Currently I have 2 ata-133 drives and I want to upgrade to this board. I looked at the PDF manual and read the forums, but people usally talk about thier Sata drives.
If it is possible to have only a Ata-133 raid setup. How/what is the best way to set it up since there is only a primary and secondary ATA connection on the motherboard. Setup a master / slave on the primary 1 slot ? or put them on thier own channel ? Note, I read somewhere that optical drives ( cdroms,...) may have a problem if they share the channel with a harddrive that is raided. So thats my dilema.
Thanks in advanced,
Jim

Quote from: crossmax03 on 02-August-05, 20:58:06
jim,
did you ever get the RAID setup to work with the IDE drives?
i was trying to connect 2 ata100 drives on the IDE2 or IDE3 ports and the bios will not seem to detect them at all,
but the RAID controller DOES detect them.
however, it will try to boot from the master drive but restarts at the windows XP splash screen, every time.
-brian
Right. If we connect two IDE HDDs on one IDE1 or IDE 2 (as Master & Slave), and plan to set up RAID.Take IDE1 for example, as long as we set up Integrated Peripherals-->Onboard Device-->RAID Config-->IDE Primary Master&Secondary RAID-->Enabled, Save&exit setup; enter RAID bios to set RAID mode, all things would be ok. But if we want to install OS in this RAID, we must press F6 install RAID driver at the beginning of OS installation. If we only use them as normal storage, OS is in other HDD, we should install RAID driver in OS.
Besides, the two HDDs could not appear in Standard CMOS Features any more, which appear in RAID BIOS.

MSI K8N Neo2 Platinum and Venice E6

Hi!
I have just bought an MSI K8N Neo2 Platinum motherboard and an AMD Athlon64 3000+ processor with Venice E6 core (ADA3000DAA4BW).
Will this mobo boot with that processor? Or do i have to use a Winchester to flash the BIOS first? Personal experiences would be helpful!
Andres.

Your new board probably came with the 1.9 bios. The new 7025v1B.zip bios (1B only a couple days old) I think is for some of the new X2 AMD Processors. The MSI link to Products/Mainboards/Neo2/Processor Compatibility is now setup to use the 7025v1B.zip bios. As I recall the previous Processor Compatibility Chart for 1.9 bios was OK for all the Venice cores (E6 or not). I think it is only some of the latest E6 bigger models are affected by the latest 1B bios. Maybe someone has the older 1.9 bios Processor Compatibility Chart.
You shouldn't need to use a Winchester, some X2 processors would be recognized as earlier X1 models until the newer bios was installed. I think you should be OK with the 1.9 bios. I have the San Diego 4000+ and my board, one month old, came with the 1.9 bios installed.

Poor gaming performance K8N Neo2 Platinum

I recently installed a new video card - BFG 6800 Ultra and the fps during gaming has dropped drastically. I thought the problem might be the video card so I flashed it to a newer bios, this had no effect. Then I swapped in my old video card - 6800 GT and the problem still existed. I also tried turning off Fast Writes and there was no change. I had my CPU overclocked and tried setting everything to default values, but there was no change. I ran Sandra benchmarks and the CPU / Memory is performing as it should. I would like to figure out if the problem is with a bios setting or the motherboard itself. Here are some benchmarks:
FarCry River Demo:
Before 52.9fps
After 28.8fps
3DMark05
Before
3DMark Score   4425 3DMarks
GT1 - Return To Proxycon   19.6 FPS
GT2 - Firefly Forest   12.9 FPS
GT3 - Canyon Flight   21.9 FPS
CPU Score   4681 CPUMarks
CPU Test 1   2.3 FPS
CPU Test 2   4.2 FPS
After
3DMark Score   2543 3DMarks
GT1 - Return To Proxycon   14.1 FPS
GT2 - Firefly Forest   6.2 FPS
GT3 - Canyon Flight   12.0 FPS
CPU Score   791 CPUMarks
CPU Test 1   0.5 FPS
CPU Test 2   0.6 FPS
Here are my system specs:
MSI K8N Neo2 Platinum 1.4 bios
Athlon 64 3000+
BFG GeForce 6800 Ultra 71.25 drivers
WD 37GB Raptor SATA
WD 160GB SATA
512 x 2 OCZ Platinum Rev. 2 PC3200
Koolance EXOS watercooling (video, CPU)
OCZ Powerstream 520W power supply

Quote from: s4eric on 17-February-05, 02:07:01
I didn't reinstall Windows, but restored to an earlier image. Everything is back to normal.
Crap....I was going to say it was certianly broke and send it to me ;-)
Glad you got it fixed.
BTW-Why did you go from 6800 GT to an ultra??? So much money sittin' around? I feel your pain.

MSI K8N Neo2 Platinum cant upgrade to BIOS 1.4, Windows wont boot.

Hello
I have a MSI K8N Neo2 Platinum and I cant upgrade to BIOS 1.4. I have tried everything and cannot get Windows XP to boot with BIOS 1.4.
I have reset the BIOS, set defaults, cleared the battery etc but when I load BIOS 1.4 (from a 98SE an ME boot dish and even from the Live Update?
The only solution is to rebuild Windows after loading BIOS 1.4???
Help

Hi !
Well, I have that problem, too. I think the reason is a new RAID-BIOS-Version built in the BIOS-Update. I´ve tried the beta-versions V1.51 and V1.5X, too - but they won´t run anyway.
My WinXp hangs while booting (before the WINDOWS-XP-Logo appears, or while fading in...). I cannot reinstall Windows completely because, when I install the 2 raid-drivers, the installation routine hangs before the licensetext - when I don´t install the drivers i cannont install on the raid-drive (beacuase the installation routine shows 2 hdds).
I think, a new driver will solve this problem, but I don´t know where to find it....
A.

K8N-Neo2 Platinum pauses for 25 sec at boot, nvatabus.sys the problem?

All,
After POSTing normally and starting to load Windows XP, my system halts at the Windows XP splash screen for about 25 seconds. Nothing happens, no disk activity or anything, the system just sits there.
I used Microsoft's Bootvis utility to see what was happening. It turns out that the nvatabus.sys driver consumes 100% CPU at boot for 25 seconds then the system continues to boot normally. Does anyone else see anything like this?
I am running the latest nForce drivers from MSI. The driver in question:
NVIDIA nForce3 Serial ATA Controller 2.6
Driver Date 6/3/2004
c:\WINDOWS\System32\DRIVERS\nvatabus.sys 5.10.2600.0446
Windows XP SP1
I have a RAID1 of two 160 GB SATA drives. The mirror is healthy and working fine.
After booting the system is rock-solid stable, no problems there. It's just this unexplained pause at boot. Does anyone have any ideas how to fix this?

ok check it out guy's this thing drove me insane all night last night and most of today. I was ready to return everything and give up. But alas all is not lost. Here is the rundown on what i just did.
My Equipment:
Athlon 64 3800+(w/ stock fan)
MSI K8N Neo2 Platinum Socket 939
2X512 Corsair TWINX1024-3200XLPRO ( with the cool led's )
2 SATA HD (1 Maxtor Diamond10 300 GB w/ 16mb cache, 1 Segate 160GB w/8mb cache)
PP&C 425 ATX Deluxe
Radeon 9700 Pro ( cat 4.8 )
Audigy2 ZS
Sony Floppy
Sony 8x52x52x32 DVD Rewrite
I have been reading and reading just like all you guy's. On a few websites i would pick up bits and pieces on what to try. Heres what i did. Upon Boot up i entered the bios. I then went to Cell Soft and adjusted my timings for my memory. I was at 2.5 not 2.75. I then set my speed down to 166. Exited and restarted. Big mistake everything ri=uns terrible slow and my expensive DDR 400 memory was showing up correctly at 333. Rebooted again entered the bios. reset my speed to 400. Then set the Overclock feature to manual. Set my timings at 2,2,5,2 200 and 2.75 volts. After saving settings and exiting I then turned off the computer. As per some other suggestions I moved my Audigy2 to the bottom most pci slot the one above the orange slot. I moved my memory to slots 2 and 4. I moved my SATA to slots 3 and 4. I rebooted went into the bios again and setup all my voltages. CPU was Auto, AGP was max yellow setting. Memory still at 2.75. I disabled the onboard serial and parrallel ports. Rebooted
Fearing the worst,
5 seconds, 10 seconds, windows screen loging prompt. There was nothing wrong at all. It rebooted effortlessly. It re found my Audigy card and wanted driver but that was it. I am going to reboot a few more times and then run sisandra to test. I hope some of this will help you. I post in a few after some of those reboots.

Problem on boot MSI K8N Neo2 Platinum

I am an italian lover of MSI motherboards.
After I bought a MSI KT3 Ultra Aru, then MSI K7N2 Delta ILSR and now I have a K8N Neo2 Platinum.
My hardware are:
MSI K8N Neo2 Platinum
Athlon 64 3200 Winchester
Corsair XMS 1024 TWINX 3200 PLL
Maxtor Diamond Plus 9 80 Gb
Asus Radeon 9600XT.
The problem is that at the power on the bios don't start. The LED on D-Bracket are three green and one red. On the manual this error are written:
Inizializing Video Interface
This will start detecting CPU clock, checking type of video onboard. Then, detect and initialize the video adapter.
This problem is frequent for my motherboard. However not always.
I attend your answer for this problem.
Thank you for all and for my english school.

Hi Italiano,
Welcome to the forum.
Have you details of your power supply. please show Maximum 3.3v,5v & 12v.
These are usually on the side of the power unit.
try:-
1) Enter bios Cell Menu - HT change from 5 ---> 4 using +/- keys. Save & exit.
If it still doesn't boot try:-
2) Re-inserting your Asus Radeon 9600XT. Sometimes they don't go in correctly.
3) See if you can boot with just 1 memory module in slot 1.
Luck

New CPU, Msi K8n neo2 platinum - no boot!

Greetings!
I got the following components:
*MSI K8N NEO2 Platinum -54g MB
*4 x 512mb Geil Value Ram
*Gainward 7800GS+ Bliss 512mb AGP
*Samsung Spinpoint 500gb SATA HD
*Corsair 620HX (620W) PSU
*CPU AMD Opteron 180 Dual Core (upgrade from AMD 3000+ Winchester)
I recently upgraded my PC with a new HD, more ram, new CU Fan/heatsink - on an AMD 3000+ (Winchester). PC wouldn't boot - I did however manage to fix it. I think it was because of the ram, one of the bricks had some dust on it. Since then, my pc has worked 100%...
Today, however, I got a new PSU and CPU in the mail! A Corsair 620W PSU and an AMD OPTERON 180 Dual. I carefully cleaned the surface on the heatsink etc, and applied an appropriate amount of "Arctic Alumina" on the CPU/heatsink (as followed per instructions from Arctic). When I have connected everything, and fire my pc up - it just won't boot.. (The monitor won't light up).
Since then, I have carefully checked all wires, unplugged/replugged etc.
But it just won't boot!
I do have the latest bios (1.0D), so it should support my CPU.
I should mention some "weird" things, though. When I try to boot up, everything seems normal (All fans are running), but there are no lights on my case! And I can't turn off the PC while holding down the "power" button on my case. I can't reset either.. as soon as I turn the PC on (by turning on the PSU power switch), the PC starts running. Normally I would have to push the button on my case. ALSO: I have cleared CMOS, still a black screen. And I have tried 2 different monitors, so I know it aint that either.
My old PSU was a Chieftec 360W one (and my case is a Chieftec also). The old PSU was connected to "SFAN2" on my MB,.. my new PSU isn't connected to any "SFAN" at all.. I doubt that has anything to do with the problem though?
Any suggestions on what I might do ?
Edit: D-bracket shows this (Yellow, red, red, yellow):
BIOS Sign On
- This will start showing information about logo, processor brand name, etc... - It stops here. No boot screen

Quote from: BOSSKILLER on 14-November-07, 21:14:42
remove power cord from the PSU(else will not work) and Clear CMOS Guide.
leave one memory stick only in a 1st DIMM slot near to CPU socket and try to boot.
Done & done.
Still no boot screen :(

K8N Neo2 Platinum 2 DIMMs won't post

I have two 512 MB Crucial DIMMs (DDR PC3200, CL=3, UNBUFFERED, NON-ECC, DDR400, 2.6V, 64Meg x 64, Part #CT6464Z40B). If I have either one installed, the system will POST. If I have both installed (I've tried them in both recommended combinations, in DIMM1 and 2 and in DIMM3 and 4), the system won't POST. The D-Bracket displays the Memory Detection Test signal. Since each stick works alone, I don't think either one is faulty. Can anyone explain why this is happening, and how to fix it?
Specs:
MSI K8N Neo2 Platinum
AMD 3500+ 939
eVGA e-GeForce6800 128MB DDR AGP 8x
Antec 380S PSU, 380W.

im having the same problem. same ram, same motherboard. except when i put the ram in slots 1 and 3 the computer will start up, but it will freeze in windows everytime. what should i do? i want to use all of my ram now only one stick!!!!!!!!!
and i have updated bios to 1.4 and it still doesnt work

K8N Neo2 Platinum wont post or boot (64 3000+)

Similar Messages

Maybe you are looking for