[K8N NEO3-F] Problem with USB keyboard and PS2 mouse after upgrading BIOS

Hello everyone!
I have upgraded BIOS from 1.1 to 1.4... I have Sempron 2600 (64bit) so BIOS v.1.1 did not recognise it.
The motherboard works, but after upgrading I have a small problem with my keyboard and mouse.
When I use USB keyboard my PS2 mouse doesn't work. When I connect PS2 keyboard mouse works!!!
Can you tell me what's wrong?                   
Thanks, bartull@           
PS. Does BIOS v.1.3 recognise Sempron 64bit? Can you give me a link to it?

I think that the problem may have been caused by flashing either with liveupdate or with winflash.  I had the problem when i used winflash correctly (shutting down all programs, checking all the boxes to clear bootblock and cmos) but had usb keyboard connected during flash.  My suggestion is to reflash with floppy to last bios version that worked using only ps2 mouse and keyboard with the following instructions:
DOS floppy flash shall be performed with :
awfl833d.exe w7030nms.180 /py /sn /wb /cc /cd /cp /f /e
(Replace biosfilename with appropriate version for Neo1/neo2 etc , switches remain the same )
After flash is complete :
TURN OFF PSU (don't restart) wait 15 seconds
Turn on again , press the power button .
Enter BIOS and load optimized defaults (NO OTHER CHANGES) , save + exit
Boot the system again with the floppy in the drive to let the DMI pool build and update itself .
If that works, then reflash to the bios you tried before with the same procedure.  Once you have stable system with ps2 keyboard and mouse working, re-enter bios and enable usb and keyboard support as a lot of bios' have it disabled by default for some strange reason.
Good luck.

Similar Messages

  • Problem with wireless keyboard and wireless mouse

    All of a sudden, after more than 6 mos., I am having problems with both the wireless keyboard and wireless mouse. I am getting a "connection lost" message on the screen with a picture of the keyboard. It only stays there a few seconds, disappears, then the keyboard is ok again.
    The mouse is even more frustrating. I am not using the ball for scrolling, just moving the mouse to move the pointer. It will be working perfectly, then for 15 to 30 seconds will either not respond, or be extremely slow, then be ok again. This has repeated a number of times today, especially when I am in iTunes. The batteries are fine in both devices, since I had the problem, changed the batteries, and still have these problems. Any ideas?

    Brian, I called Apple and I think they fixed the problem with the keyboard. Unfortunately, I did not write down the exact keystroke sequence they gave me, but let me tell you what I did. I unplugged the computer and waited 60 seconds. After I plugged in back in, I was told to immediately hold down 4 keys. I think they were something like Ctrl, Command, Shift, and R. Those may not be the exact keys, maybe it was Option instead of Ctrl, and maybe R is not right. I am not sure. Those keys are held down until the second beep is heard after the computer was turned on. Supposedly, this re-established connections between the computer and the keyboard. Sorry I did not write down the key combination. If you can, call Apple and get the proper key stroke combination

  • Problem with home button and "messages" app after upgrade to iOS 4.1

    Hello,
    I have noticed two interesting problems with my iPhone 4. I am not sure if it is in conjunction with the upgrade to the iOS 4.1 software, but I did not notice the problem prior to this. Both of these problems are very odd and are hit or miss. I have tried restoring and the problem is still present. Also, since both problems have presented at the same time, that is why I am starting to believe it is not hardware...
    Problem 1: The home button has become considerably unresponsive. This is not all the time, but it does happen a lot. Sometimes it won't work for about 5-8 clicks and I have to use the power button to access the phone.
    Problem 2: When composing a new text message the cursor would always default into the "To:" section of the app which allows you to easily type what contact you are trying to message. However, I am having the issue now occasionally when I am in the messages app and select to compose a new text message that the cursor now defaults into the chat box (where you type your actual message). This is very annoying and I know that this is not the intended behavior of this.
    Please let me know if anyone has experienced similar issues and can provide me with some feedback.

    I have not experienced the same.
    I have tried restoring and the problem is still present.
    You restored from your iPhone's backup, or as a new iPhone or not from your iPhone's backup?
    If whatever software problem is causing this is included with your iPhone's backup, restoring from the backup will also restore the problem.
    Try restoring as a new iPhone or not from your iPhone's backup to see if this makes any difference. If not, more than likely your iPhone has a hardware problem.

  • Problems with Hotspot, EDGE, and 3G internet after upgraded to iOS 4.3

    I just upgraded my iPhone 3GS to iOS version 4.3 , but after I installed it, the Personal Hotspot badge on Settings>General>Network appears, but it keeps at the "loading circle" sign (the same one when the iPhone is turning off). Besides that I realized that my 3G internet is not working, neither EDGE. none of the 3G or EDGE icons appears next to my carrier bundle, how it usually do. Wifi is working though. I tried to solve the problem restoring the iPhone, but the problem persisted even after the restore. What's happening to my iPhone 3GS?

    Hi man!
    have the same equipment and the same problem, who is your mobile operator?
    I'm from Chile and my operator is Movistar, I think they blocked the service hotspots.
    Best regards

  • MSI K8N Diamond - Boot problems with USB devices attached.

    Hi There.
    I have been seeking the forums, but havent found the answer to my problem yet. 
    This is how it goes with ANY USB devices attached to either of the four USB ports on the Motherboard.
    When i turn on my system, it hangs in the POST right after displaying the BIOS version (Which I have updated to 1.6) - I cant use my Keyboard to get to the BIOS setup.
    Without USB devices attached...
    The system boots without problems. And in Windows XP SP2 i can insert my keyboard, mouse etc. and everything works great - both USB 1.1 & 2.0 devices.
    I have disabled the KB/USB.. in BIOS and I have disabled the "Boot on other device" option as well.
    As I have found on this forum, a lot of people have problems with USB Front panel and D-Bracket (USB ports) connectors causing the system to hang - But my D-Bracket (USB connectors) and my front USB port is at this time DISCONNECTED - so this cannot be the problem.
    The D-Bracket shows the "Bios Sign On" information - and stops at that point 
    Am I having a malfunctioning Motherboard here, or are there any solutions to this problem?
    Please help me as I am desperate to have my system work properly.
    Regards
    Stieper

    Well I have read about that somewhere in here, but my problem is NOT with an USB hub, but with any USB device attached to the motherboard's USB slots. It is driving me nuts to be honest!! I think it might be time for RMA 
    What do you say guys - is my Motherboard ready for RMA, or do I have to try something specific berfore sending it to the retailer??

  • Problem with Bluetooth Keyboard and Lion?

    I've just purchased a 21" imac running os x lion 10.7.3 and although the mac sees the keyboard when I set up the Keyboard from system prefs, it says 'keyboard cannot be found even though the Bluetooth prefs says it's there'.
    Second, there's an on/off button on the right hand side which glows green for a second when it's pushed, and ditto if you push it again, so I don't know if the keyboard is on or off! Surely it should glow grren when ON and not when OFF or is there a problem with the keyboard itself?
    Bill

    Hello:
    I've just purchased a 21" imac running os x lion 10.7.3 and although the mac sees the keyboard when I set up the Keyboard from system prefs, it says 'keyboard cannot be found even though the Bluetooth prefs says it's there'.
    Is the KB working on the system or not?
    Second, there's an on/off button on the right hand side which glows green for a second when it's pushed, and ditto if you push it again, so I don't know if the keyboard is on or off! Surely it should glow grren when ON and not when OFF or is there a problem with the keyboard itself?
    That is the way it is designed.  When you turn the KB on, the light is on for a brief period of time.  It does not stay on.
    Barry

  • Mac mini first start up trouble with wireless keyboard and magic mouse

    Do you need to use a USB keyboard and mouse for your first mac mini start up? I've just fired it up for the first time and got a strange start up screen. The icon looks like a battery compartment with a green switch with an arrow pointing up. I've read all of my manuals and can not find anything to help me. Any ideas??

    Yes you need to use a wired keyboard.

  • Help with Wireless Keyboard and Mighty Mouse please!

    Hello. I own the wireless Mighty Mouse as well as the wireless keyboard for Mac, and while ago I set them up to work on my Mac, but I don't use them very much so I want to give them to my parents for their Mac. The thing is, I forgot how to set it up or install it or whatever. Can anyone tell me how to get the wireless mouse and keyboard to work, or what the install process is for them? Was there a CD that came with them that I need to install drivers with or something? Anyways, I have the mouse and keyboard sitting up here next to this computer, and I've turned them on with the switches on the back, but they're not working. What do I do next? Thank you!
    -- Andrew

    Solution
    Turn your Bluetooth keyboard and/or mouse off for 30 seconds, then back on.
    If the keyboard or mouse doesn't respond, or if an alert message appears again:
    Connect a USB keyboard or mouse.
    Open Bluetooth preferences (choose System Preferences from the Apple menu, then click Bluetooth).
    Verify that Bluetooth is turned on. (You can also do this with the Bluetooth menu bar item, if enabled).
    Pair the keyboard or mouse by setting it up as a new device.

  • Problem with usb-ports and keyboard

    Hi.I reinstaledl windows xp sp3,downloaded all drivers from this site and now i have a problem.When I push any key on keyboard-my usb-ports dont working.Its like they dont get power supply.Sorry for my bad english.And then I stop to push-usb ports start to work.What can I do?Thanks.

    hi tony7161,
    Welcome to the forums.
    It looks like there's a short somewhere when you touch that keyboard and causes the USB ports to stop. May I know what lenovo computer do you have?  Have you tried booting into safe mode (you need to press F8 upon boot-up and choose Safe Mode) to see if the issue persists?
    Let me know your findings.
    Cheers.
    Did someone help you today? Press the star on the left to thank them with a Kudo!
    If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
    Follow @LenovoForums on Twitter!

  • Problems with USB connection and PC Suite

    Connecting your device to the PC via USB doesn´t always work as smooth as it should. You can either use the setup´s repair function or if you are experiencing more serious problems, you need to uninstall all Nokia software form your phone and get it back on to make to work again. 
    This is how you do it:
    Run the Nokia PC Suite setup file again and choose "repair" instead of "uninstall". This should solve some of the connectivity problems. If it didn´t work for you continue with the instructions below.
    Go to Start --> Settings --> Control Panel --> Software, there you need to uninstall all Nokia software (Nokia PC Suite, Nokia Cable driver, PC Connectivity Solution ...)
    Download and run Nokia PC Suite Cleaner
    Reboot your computer
    Download and install PC Suite here.
    Connect your phone via USB cable (if possible use a different USB jack) and follow the instructions on the screen.
    Now you´re set up to manage your phone with PC Suite!
    For further questions ask within the board, for improvements on this article contact me.
    Thanks to users scoobyman, cricfancy and shuntfield for their collaboration.
    Message Edited by illinjah on 16-Aug-2009 07:02 PM
    By clicking the "Kudos!" or the "Solution?" button on the right you can say "Thank You" and you´ll show the author and others that the post is useful.
    The day we stop improving is the day we stop being good.

    Hi pudu
    thanks for the reply!
    so sad, that doesn't work for me. the same with Nokia_PC_Suite_6_84_10_3_eng_us_web.exe
    I have widcomm stack for bluetooth, there are lot of concerns about this,
    but I do not understand why it cannot be connected via USB, too. Oh, no, it is connected, but that makes no sense

  • Problems with USB port and song transferring;

    Hi! I just got an iPod and I am having problems with it. My computer doesn't have a Hi-Speed USB port, even if it's 9 months old. Some of my friends don't have it either but they still are able to transfer songs onto their iPod. For mine, it keeps saying "Do Not Disconnect." I waited for 5 hours last time I got it and it still isn't working.
    I also updated my iPod software today and the iPod icon isn't appearing on the bar to the left in iTunes. I'd really appreciate any help on this! As well as if I really need to do something about the ports or if it could function like this normally.

    Quote from: Svet on 08-December-10, 00:48:07
    Install chipset drivers from MSI web:
    http://eu.msi.com/index.php?func=driverfile&dno=2427&i=0
    +
    NEC USB 3.0 Drivers:
    http://eu.msi.com/index.php?func=driverfile&dno=11189&i=0
    are these the same driver provided with the disc driver? as i already installed both of these..

  • Mapping problem with Wireless Keyboard and Japanese iPhone

    Hi everyone:
    This seems to be a slightly obscure question -- at least, I can't find a ready answer for it with the search terms I've tried, possibly because most people don't use this particular accessory with the iPhone.
    I have an iPhone 4 that I bought from and use on Softbank, the carrier in Japan, where I live.  While visiting the United States recently, I bought an Apple Wireless Keyboard from an Apple retailer.   I wanted to carry it with me for use with my iPhone, so I would reliably have a convenient way to access the Internet without being confined to the touchscreen keyboard.  (I live in a rural area where WiFi spots are uncommon, but my iPhone's access to Softbank's data network is fairly good and consistent.)
    However, to my frustration, I can't use the keyboard due to a mapping problem.  The Bluetooth connection is fine -- the iPhone can discover the keyboard.  However, the mapping is off: typing "Q" gets me "A," typing "Z" gets me "W", numbers and punctuation are off, etc.  The key point: This is NOT a problem with the International Keyboard settings (under the Settings -> General -> Keyboard -> International Keyboards menu).  I have the Keyboard setting set to QWERTY, which is the layout of the Apple keyboard; I have tried all the other possibilities, just in case.  None of them work.  Setting the Keyboard setting to QWERTY does not make the external QWERTY keyboard map correctly.
    The rather ironic addendum is this: While on a recent trip to Tokyo, I visited the Apple store in Shibuya and, after concluding the main business of my visit (discussing my MacBook's battery problems with an English-speaking staffer), I took out my iPhone and keyboard and asked him about my mapping problem.  He started with the Keyboard menu, tried the same things I had tried, realized they weren't working, and puzzled over the problem for a while.  Then he did this: He hit a key combination (I believe) that brought up a menu on the iPhone's screen.  "Ah, there's your problem," he said, and selected a new setting.  The problem was instantly fixed.
    To my chagrin, however, I neglected to write down what "Ken" had done to fix the problem.  Argh... I was looking at the iPhone upside-down; I'd already taken up more than half an hour; people were waiting, and I guess, being used to living in the countryside now, that I'm not used to Shibuya crowds any more.  Anyway, I didn't take careful notes or ask him to walk me through it, and now I cannot recall or repeat what he did.  And I still can't use my keyboard!
    Any ideas or advice, anyone?  How did "Ken" fix my problem, and how can I repeat it?  Much, much appreciated, in advance.

    THAT'S IT.  Sir, you have solved my problem.  Thank you!!
    And I feel a little silly; this will doubtless seem to an expert as if it should have been obvious all along.  But isn't that always the way in hindsight?
    Here's what happened: The key combination I was trying to remember was "Apple/command + space on the hardware keyboard," as you just said above.  The "menu" it brings up is, apparently, a list of keyboards.  I take it that this list is the same as the list of the "virtual" keyboards on the iPhone?  I have never had more than one external keyboard -- the Apple Wireless -- but I do have several keyboards active virtually, as the iPhone in Japan seems to come with both the "Nihongo Ten-key" and the "Nihongo Romaji" keyboards active, and I added several other languages as well.
    When I hit "Apple/command + space," this list comes up on the iPhone's touchscreen.  Highlighted and checked at the top is "English," just as if it had been selected all along.  But nonetheless, when I first turn on and pair my keyboard with the iPhone, I need to perform this key-combination action, as if to "reselect" English, and then the keyboard promptly starts working properly as QWERTY.  I can only assume that one of the others had been default-selected before -- presumably one of the Nihongo ones? -- and that this was causing the interference.
    Thank you again!  You have made me and my wireless keyboard very happy.

  • Airport Extreme - problem with usb printer and usb disk

    I have Airport extreme with firmware 7.1. I try connect usb disk and usb printer with usb-hub to airport. I can't get disk or printer working. Also try connect only disk or printer without usb-hub to airport getting same problem. How I get disk and printer working with wireless network (windows pc computers)?
    1)
    My printer is HP PSC 1210 all-in-one ( http://h10025.www1.hp.com/ewfrf/wc/product?product=90764&lc=fi&cc=fi&dlc=fi&lang =fi&cc=fi&y=0&x=0 )
    - printer seems working fine after installing bonjour printer installing wizard.
    - I get error (in windows) when I try print document from word. Error only says "error printing" in status value.
    - In airport utility all seems ok. Airport see usb printer "Hewlett-Packard psc 1200 series"
    - printer protocol is RAW and driver manufacture HP (also try with microsoft driver)
    2)
    USB disk is Targa Databox II 250
    - Airport utility says "Disk needs repair. Errors were found with a disk connected to your airport base station. please connect the usb disk to your mac or pc and use disk utility or another disk application to repair the disk"
    - I have connected Targa usb disk to windows pc and run scandisk and defreg. No errors found in windows. Result..no help for airport

    I have a similar problem to your second issue. Tried connecting a Netdisk to the USB port of the Airport Extreme and it also said there was a problem with the disk. Have performed a low level format on the disk and Airport Extreme still complained the disk had a problem.
    After unplugging the disk, my route decided to stop allowing wireless connections even after rebooting. Ended up having to hard reset the Airport Extreme and reconfigure it with my old settings to work again.
    FWIW, the first Airport Extreme I purchased today only worked on 802.11a and steadfastly refused to work on b/g so had to get a replacement. I suspect Apple's quality control is not quite as good as it used to be.

  • Problem with USB speakers and new Mac Mini

    I have a USB sound system consisting of a pair of Harman Kardon soundsticks and a woofer from probably 10 years ago (bought and used originally with a Mac). I have tried driving it my new Mac Mini. It works fine for about a minute; then the music stops. Here's what I've tried to diagnose the problem:
    1. The problem does not occur when these speakers are driven from my Macbook Air (about 3 years old).
    2. The OS and iTunes software is up to date on both machines (10.9.5 and 12.0.1.26).
    3. It does not depend on which USB port I use on the Mac Mini.
    4. Using a port on a USB extender on the Mac Mini does not solve the problem.
    5. The iTunes Preference settings are the same on both machines.

    Sorry, no actual experience with USB Audio devices.
    I found this in the Pro forum, but the outlook doesn't seem good:
    http://discussions.apple.com/thread.jspa?messageID=1739084&#1739084

  • Serious problem with xorg - keyboard and mouse locks all the time.

    In the last week I've notices serious problems with xorg.
    After some event, I am not sure which one, keyboard stops responding.
    Mouse cursor works, but I can't click on anything.
    I can't switch to text console.
    But I can kill xorg with CTRL+ALT+BACKSPACE.
    Have you noticed something similiar?
    I use xfce4, [testing] repository.

    Jacek Poplawski wrote:
    In the last week I've notices serious problems with xorg.
    After some event, I am not sure which one, keyboard stops responding.
    Mouse cursor works, but I can't click on anything.
    I can't switch to text console.
    But I can kill xorg with CTRL+ALT+BACKSPACE.
    Have you noticed something similiar?
    I use xfce4, [testing] repository.
    I had that a few days ago, couldn't reproduce it. I was also running xfce4. I havn't had it today and im running xfdesktop+xfce-mcs-manager+pekwm+xfce4-panel... so it may have been xfwm4.
    James

Maybe you are looking for