K8n neo4 boot problems ...please help!!

Heres my specs:
amd 64 venice 3200+
gigabyte 6600GT
seagate SATA 200gb
2x 512 OCZ ram
stock PSU
I just added a Thermaltake Big Typhoon to replace the stock AMD heatsink. The installation was perfect and at first my pc booted up normaly. I turned it off and put everything together and then i get no post. I had 2 green LEDs at the top 2 red at the bottom AKA the "Decompressing bios image to ram for fast booting" ??? I looked around here for solutions and tried clearing my CMOS, taking out the battery, using only essential compentants, and taking out my graphics card. Unforunatly none of these methods work and I am stuck with a dead PC. I even took off the new heatsink and put on the old stock one to see if it worked but I got the same error. I really don't think it is a mobo or PSU issue because I've had this system for over a year with zero flaws.
PLEASE HELP I've been at this for the past 5 hours with no success

Eeek!
Same thing happened to me with my Thermalright XP90...
Was removing the H/S once & didn't have the thing held down securely & the damned thing popped up and pulled my CPU right out of the locked socket when I released the clips on one side. I had a bent pin too, but I managed to fix it. Scary.
Thermalright really needs to rethink their mounting scheme.
Those things take quite a bit of force to hold down - hopefully you didn't crack a trace on the board while messing with it. That's the biggest fear I have with mine. I'll be chucking my XP90 on my next build for that reason.
I'd try to find a way to test your CPU in another board to see if it still works.

Similar Messages

Mac booting problem - Please help! very, very desperate!

My mac was being very, very slow so I turned it off, then as it it was booting it was taking ages so i restared in safe mode. While booting in safe mode the black bar at the bottom goes around 2/5 of the way across and then my macbook just switches off.
Ive tried:
fsck
disk utility repair/verify
reinstalling OS X Lion
When i tried to repair, it said i needed to erase everything and reinstall the OS. Last night when i tried to it said both drives are locked so i couldnt. And now when i just tried again, neither drivers are appearing; the box is just blank.
Let alone my livelyhood on the laptop, i have thousands and thousands pictures which if lost, would genuinley heartbreak me. I have much valuable data on my laptop and i really dont want to erase all data, because me being the gigantic fool that i am, i only have one time machine back up from about a year and a half ago.
Please, please help.
Thank you!

humzasadique,
unfortunately you’ve now discovered where the value proposition lies in making regular backups — if your livelihood depends upon your laptop, that lack of due diligence is rather baffling.
Which model MacBook Pro do you have, and which version of OS X is installed on it? Do you have an external bootable drive?

KT4V BOOT Problems please help quick

ok
i just got everything running again, then i replaced the cup heatsync and fan.
now, everything starts up, cd roms spin up, hdd's spin up, but the monitor shows nothing at all the usb mouse does not light up.
please help me figure out whats wrong, i just cleared cmos, with no luck.
ill do it again..
my system,
350W PS
kt4v
2 hdds 20+40 gig
Radeon 9200 overclocked with huge overdone 50$ heatsync + fan thermaltake
Athlon 2100 xp tbred B not overclocked.
1 stick pc2700 ram 256MB
2 STICKS 512 pc 2100

Quote
Originally posted by Archangel4life
nope returned it today for a full refund :(
Good no money lost
[STRIKEOUT]yeah try the GeForce 4 and see what happens?[/STRIKEOUT]
darn

T30 boot problem - please help

1 beep then 3 beeps then 3 beeps then 1 beep upon startup.
I can hear the machine running, but the monitor is completely black - not a single flicker to be seen.
This is my daughters laptop, used mainly for surfing the net and listening to her music. If it's fixable, I'd prefer that then going out and having to buy her a new one.
Any ideas on the beep sequence? Is it worth bringing it in to a computer repair shop?
The machine was bought used about 1 year ago, so there is no warrenty. She also told me that before this happened, it was working fine. No spills, no dropping it, etc. Just one day it wouldn't boot.
Ideas?

lynn893, welcome to the forum,
according to the Hardware Maintainance Manual your beep code indicates either failed memory or a failed mainboard. As T30 systems are known to have a problem with one of the memory slots I would start by removing / swapping around the memory. Instructions on how to do his can be found in the HMM.
Good Luck
Andy ______________________________________
Please remember to come back and mark the post that you feel solved your question as the solution, it earns the member + points
Did you find a post helpfull? You can thank the member by clicking on the star to the left awarding them Kudos Please add your type, model number and OS to your signature, it helps to help you. Forum Search Option T430 2347-G7U W8 x64, Yoga 10 HD+, Tablet 1838-2BG, T61p 6460-67G W7 x64, T43p 2668-G2G XP, T23 2647-9LG XP, plus a few more. FYI Unsolicited Personal Messages will be ignored.
Deutsche Community Comunidad en Español English Community Русскоязычное Сообщество
PepperonI blog

K8N Neo2 LAN problem, please help!

Hi all,
I have some problem with both my 2 LAN port onboard. Please refer to my Sig for hardware details.
The first problem is, my Realtek 8169 LAN port is working fine, but yesterday I suddenly realize that it is always running at 10Mbps to my ADSL router rather than 100Mbps. My WAG54G does support 100Mbps and it is confirmed with my laptop. I try to set my Realtek LAN to 100M Full Duplex, but if I do that it will not receive any packet. If I try Auto Negociate, then it always falls back to 10Mbps. I tried 2 different LAN cable, the same result. Upgrade to the latest Realtek dirver, same result. If I just unplug the cable, it says 100Mbps Non Operational, but in theory, it should say 1000Mbps Non Operational.
The second problem is, if I try to use the nVidia LAN port, it will establish as 100Mbps, but I can't browser any web site. I can ping www.yahoo.com and receive response, but I can't see anything in my browser. If I unplug the cable, it says 1000Mbps Non Operational.
It's driven me crazy. Can anyone help me on this? Thanks!

check to see if the nvidia lan has a mac address
open up network connections and right click the nvidia lan connection after putting cable in that one, click status/support/details and check to see if mac address is listed, if its ff-ff-ff-ff etc you have no mac address set for it, you need to boot into bios and enable the hidden options press shift f2 then alt f3 , then goto intergrated peripherals and press return on the enter mac address, then enter the mac address located on the lpt/old printer port. then press f10 save and exit.
hope this is why it's not working, check your network cable as well, change it incase its faulty, or make sure your router can uplink / accept straight/crossover cable.

Solaris install/ boot problems please help

recently had to use solaris at work and liked it. So thought of getting it solaris 10 on intel box at home to learn it. I have never worked on a unix based OS before. When I installed the OS first time, the desktop would not start up, this was because of network setup. Reinstalled worked. After a week due to some problem i had to reinstall OS, installation went fine and but when i reboot i get this errror.
cannot find mis/krtld
boot error loading interpreter(misc/krtld)
elf32 read error
load error read of "platform/i86pc/kernel/unix failed.
boot path /pci@0,0/pci-ide@1f,1/ide0/cmdk@0,0:a
i have been trying to reinstall with many option like formatting with windows fdisk, linux installer everything as I saw somehwre that disk needs low level format.
I have googled but could not find any reason.
When I try to format disk using windows this is the information gatherd
Partition1 (solarisboot) 12 MB
partition2 unknown 152610
Hardware
pentium4 2.4 GHZ
1Gb DDR memor
Intel Original mother board.
140 Gb hard disk
Installation
install type 3 (tried all options)
entire disk for boot and solaris
accepted almost all parameters.
downloaded again , burned a DVD still same.
Any help will be highly apreciated, as I have been trying out everything I could find, also I really want to learn to use solaris

Looks like a boot disk problem.Try doing a lowlevel format with the respective tools.(Ex.If seagate harddisk download seatools) No try to install the OS.If you are facing the same problem try installing windows and see.The error looks like a bad blocks in the disk.

MSI K8N Neo 4f problems please help.

My rig
Processor
AMD Althon64 3000+ Venice
Mainboard
MSI Neo4f
Graphics Card
Leadtek GF6600GT Extreme 128mb
Memory
2x512 Twinmos ddr400
Display
Viewsonic VX912
Storage
Hitachi 250GB SATA
Optical Storage
MSI DVDRom/ LG 4163B DVDRW
Casing
Cheapo
PSU
Verudium Vortex 430w
Audio
On Board
OS
Win XP SP1
The above rig bought 3 weeks ago,
and its been giving me unstability problems. After installing winxp SP1, when I start installing drivers, these problems would come.
1. PC would freeze up now and then.
2. USB keyboard and mouse sometimes wouldn't work after bootup although PC is still running
3. Blue screen! now and then.
4. Sometimes different software installation would give error but re-running the installation would be fine.
The above mentioned problems could is still persisting after 2 weeks. I've reformat and reinstalled winxp 4-5 times and the above would still occurs sometimes, even in the middle of installing drivers. It comes randomly and not during a specific software/driver installation.
I've run memtest and RTHBRIBL overnight with no errors and I'm suspecting motherboard. Strange thing is that the MSI live update program help me flash bios on my motherboard and would still prompt me I need to flash my bios everytime.
I've basically almost isolate everything except motherboard. I hope someone can help me determine if it is my motherboard problems. I've going crazy already.

Quote from: Tango on 14-August-05, 21:16:35
Do you have Cool n Quiet enabled?
If so disable it , and report back.
Verudium Vortex 430w
Please post the voltage rail ratings.
Have you tried Prime95?
http://www.mersenne.org/freesoft.htm
It is a stress test that runs under windows and also can be used to test your memory.
EDIT: http://www.alevtav.com/products.php?brand=1&ATSid=4a2fe5368de8eb29c5723c93b90aec9f
If that is your PSU it is fine.
What nforce drivers are you using?
yes thats the vortex i have
cool and quiet disable thru bios
nforce drivers. seems to have more problems with the newer downloaded from MSI website. but can't really confirm
I've download prime 95 but I did not run it because by running RTHBTIBL will cause my cpu temp to go to 47 deg c. But I'll try it tonight.
note that I'm not running raid. just a 250gb SATA hitachi HD.

10.4.10 Update Problem-- PLEASE HELP!!!

I have a 17" Powerbook 1.33GHz. I just installed the 10.4.10 update. Now the computer wont boot on a power adapter. I had problems after the first update with changing state while the computer was asleep (ac adapter to battery) which would result in black screen and forced a hard reboot. Now when I try to power-up the computer from the restart (or regular reboot) it just doesnt boot. Please help if anyone has any ideas. I dont mind even if there is a way to undo this update.
Jacek

Alright - I think my computer is good again. Here is what I did. I dont know how much of this will actually do anyone any good, but I figured if I listed it all step-by-step, maybe it would do some good to someone.
1) Restarted with AC in. Didnt boot - black screen
2) Restarted with no AC in. Booted up ok. Restarted again (I guess it was a double restart) Booted again alright.
3) Plugged in the AC, computer froze :-\
4) Did a powerbutton hard reboot (5 second hold down)
5) Computer died - I left if at office overnight. (By died i mean wont boot with AC adapter)
6) Computer turned on fine in the AM. Some of my Brother drivers got a little fudged, so I had to reinstall them. Needed a restart (on AC)
7) Didnt restart (black screen)
8) PMU Reset
9) So far so good...

X-Fi Fatal1ty Plat1num Champion Ed. problem, please help!

9X-Fi Fatalty Platnum Champion Ed. problem, please help!? Hi there everyone,
So i have a X-Fi Fatalty Platnum Champion Ed. and a computer with Windows 7.
I've searched the web and i found many people saying that the card it's working and perfectly compatible so i would like to exclude this option as far as the problems that i'm having.
So, right out of the box i've placed the front panel in with the ribbon cable and the power connected to it, then i connected the other end of the ribbon cable and finally placed the card in one of the PCI slots i have free.
Now, when i start my PC, i don't hear any particolar "beep messages" but nothing will come on the screen, in few words my PC will not boot at all. I can hear the HDD spinning, everything sounds normal except for that "little" problem.
So, i re-did all the connections thinking that maybe i did something wrong, but following the instruction i did exactly as told. So i tried again to power up the computer and i've noticed that the X-Fi logo is lit up (red light) and.. I don't really know if that means something or it's just something aside that doesn't really matter.. But, what is it's The PCI card is broken or there's something else?
I did try to disable the sound card (integrated mobo sound) from the BIOS but that didn't change anything. I did try all the software options but this looks like more of an hardware problem (please correct me if i'm wrong and/or i've missed something).
There's something that popped up in my mind.. the PSU. I noticed that i have a 300W PSU (mm.. low, isn't it's)?and i was wondering if that's enough or i need a more powerful one.. and if that's may be the case for the PCI to not work at all causing all i've already explained above. I mean.. It seems like i've installed a dead peripheral and that's impeding the computer to start up..
I don't know.. I need clarification and help, PLEASE.
Thank you very much in advance!

Look at the beta thread sticked above but good luck waiting for a new driver. That beta driver has been there since January and although better than the normal driver it is still crap.
All the boot type issues are with the SSD but if you getting in game crashes etc... under windows 8 that is simply that the driver stinks.

P6N Lots of problems please help

P6N Lots of problems please help
The setup is the following:
P4 D935 3.2gHz
P6N Diamond MS-7320 Bios 1.3V
Corsair XMS2-6400C4DHX
NX8600GT-TD512EZ/D2
Seagate Barracuda 7200 250Gb SataII 16Mb
Akasa 460W Dual Rail
Please help I have lots and lots of problems with lockups that can happen any time post , bios , loading vista and sometimes during OS. Some times will work ok play games etc. Already tried different combinations fitting the mem modules even tried and some pc4200 modules same problems. Spent lots of hours clocking the mems with different settings but non is stable. I am not interested in overcloking just to make it stable to start with. When is actually running is fine is more than enough for me. Already looked to lots of posts on the msi forum but… Since the cpu is old can I go back on an older bios version???? The Corsair modules have to run at 2.1V or is it possible to use them with slower setting. So confused so lost ….. please HELLPPPPP
Any help greatly appreciated.

please, don't buy any more unneded parts. first find the problem then buy if no solutions available.
One thing I find with BIOS issues is to do a full clear.
1. disconnect the power cord from the power supply(turn switch to off if there is one.
2. hit the power switch to clear the power out of the system.
3. set the cmos jumper to clear and leave there if one is available.
4. Pull the battery.
5. carefully short out the battery connector on the motherboard to drain any power left.
6. press the clear cmos button and hold for 30sec minimum, if you didn't have a jumper to set.
7. replace battery, move jumper back, plug in power cord, turn on power sipply switch.
Now it should hopefully power up. go into BIOS and load optimized results. hit save and exit and when it gets back to the post screen, go back into bios and set your normal MB settings(ie. set boot devices, boot order, disable sound if using sound card, etc...)
go into your H/W Monitor section and list the CPU Vcore settings to make sure it is getting the power it needs. I just looked it up and it's suppose to run from 1.225v - 1.325v.
also, try your most generic ram you have with auto settings. the faster the ram usually the more volts they need and default volts are 1.8v for ram and sometimes faster chips have issues with lower volts.
Let me know how this works for you.
-=Mark=-
ps. make sure everything is unplugged from the computer you don't need. just cpu, 1 stick of ram, and video. and of course keyboad and mouse. Please make a signature with all your systems specs including make and model numbers. I hate guessing at solutions and I'd hate to see you buy any more unneccessary parts because of lack of information.

System D.O.T automatically why? problem please help me

hello everybody,
please help me my system says at post message that wrong cmos information then gives me option to boot or go to bios when i check my bios , my ONBOARD LAN GETS ENABLED AUTOMATICALLY ,the Frequency tab i check says something like PRIVATE DOT ENABLED AND CPU+AGP SOMETHING i mean my comptuer gets fast and the CPU fan becomes on full speed and i hear loud noise until Corecenter runs it becomes quiet again. the question is is this a bios fault or something , DID ANYBODY WHO BOUGHT 865PE PLATINIUM BOARD EXPERIENCE THIS PROBLEM PLEASE HELP ME MY CONFIGURATIONS ARE BELOW
PENTIUM 2.40 GHZ PRESCOTT (54 C MAXIMUM)
MSI 865PE PLATINIUM BOARD (IT GOT NO RAID ABILITY)
DDR 400 MHZ KINGSTON SINGLE CHIP RAM (ALTHOUGH IT RUNS AT 333MHZ)
MSI GEFORCE FX 5200 T128 (64 BIT DAMN IT!!!)
MSI CD ROM
SONY FLOPPY
COMPUTER CASING WITH SMALL MINI ADDITIONAL FAN ON THE SIDE (IT RUNS MAYBE AND ALSO GIVES ELECTRIC SHOCK OR SOMTHING SOMETIMES)
STABIMATIC 500V AUTOMATIC STABILIZER(ALTHOUGH I HAVE UPS CAN SOME BODY TELL ME IS UPS ALSO STABILIZER OF APC(AMERICAN POWER ----)
AMI BIOS 3.4
SO CAN ANY BODY TELL ME IF THIS IS A PROBLEM OF BIOS SHOULD I UPGRADE TO LATEST
WHAT METHOD THROUGH AUTOUPDATE OR MANUAL , I ONLY ONCE DID MANUALLY ON MY DELL 4100 PIECE OF CAKE !

Hi,
Go to here for MSI LIVEUPDATE
http://www.msi.com.tw/program/support/software/swr/spt_swr_detail.php?UID=556&kind=1
Install and run program.........
BIOS problems:
http://www.msi.com.tw/html/support/bios/note/boot.htm
If you would like to download bios and install........
http://www.msi.com.tw/program/support/bios/bos/spt_bos_detail.php?UID=556&kind=1
You can also choose 3.7 if wish too first.....
I am sure this will help you.
Del

990fxa gd80 raid 0 problem please help me i am begging you

so i will start with my set up
990fxa dg80 mb
fx 8350 cpu
780ti
8 gig of ram
256 hdd
2x samsung 850 evo
750 hybrid drive
So at this stage all my data is on the 750 hdd and the disk is stored away. my problem started with me buyng 2 mx100 256 ssds . If my bios is set to ide or ahci they work fine i had my windows instaled on 1 of them all woks fine. Once i switch my bios to raid ( before i set up my raid 0) boot up win 7 instalation i do not see any drives ( i know is normal) load the drivers for the raid controler (sb950 for w7 as it says in themanual) and only my 256 hdd shows up but not the ssds . Than i set them up in ld raid 0 same problem . Tryed on another 2 mbs ... 1 same and a gygabite same problem. So i was sure there is a problem with ssds. I got rid of them got 2 new 850 evo 250 gb same problem. please help me i am so desparate i am willing to pay woth body organs for help

I..have a few questions...
1. You set BIOS to the RAID mode, and under that option there's a Board SATA RAID ROM, do you set it as Legacy ROM?
2. Did you enter Ctrl+F to initialize the drives/Delete Array(If they're used SSDs) and create RAID0?
3. Is your Win7 64 bit or 32 bit?
4. I assume it's 64 bit, did you copy the W764 folder for driver loading?
And make sure you get the driver from here:
http://www.msi.com/support/mb/990FXAGD80.html#down-driver&Win7 64

My iphone is on recovery mode and i can´t turn on it, when i try to recover it from itunes i get: "unknown error (36), i´ve tried to do lot of things but i can´t solve my problem. please help!!

my iphone is on recovery mode and i can´t turn on it, when i try to recover it from itunes i get: unknown error (36), i´ve tried to do lot of things but i can´t solve my problem. please help!!

Hi, i had the same problem. Try to find the file "apple" or "itunes" don't know it anymore exactly. Ahm well you need to delet any information or just plug in your iphone into an other computer. important is that your iphone never has been pluged in this computer before. This was what i did, and it worked!

Problem Please help me.....Let me know the area to look for it I am a DBA..

Problem Please help me.....Let me know the area to look for it I am a DBA..Thanks in advance to let me know the cause and the area to look and fix it...
Server Error in '/' Application.
Problem with SAP/BAPI. SAP.Connector.RfcCommunicationException: Connect to message server failed Connect_PM MSHOST=prddb01.lamrc.com, R3NAME=PRD, GROUP=Prod HR PRD LOCATION CPIC (TCP/IP) on local host ERROR service 'sapmsPRD' unknown TIME Wed May 04 08:59:06 2005 RELEASE 620 COMPONENT NI (network interface) VERSION 36 RC -3 MODULE ninti.c LINE 428 DETAIL NiPServToNo SYSTEM CALL getservbyname COUNTER 1 at SAP.Connector.SAPConnection.ThrowRfcException(RFC_ERROR_INFO_EX rfcerrInfo, Encoding encoding, String languangeCode) at SAP.Connector.SAPConnection.Open() at SAP.Connector.SAPClient.RfcInvoke(String method, Object[] methodParamsIn) at SAP.Connector.SAPClient.SAPInvoke(String method, Object[] methodParamsIn) at SoftwareKeySAPG.SAPProxy1.Z_Bapi_Load_Kpi_Region(ZSOFT_KPI_REGIONS_MTable& Kpi_Regions, ZSOFT_PROD_TYPETable& Prod_Type) at SoftwareKeySAPG.SAPGSK.LoadKPIRegion(DataSet dsProduct)
Description: An unhandled exception occurred during the execution of the current web request. Please review the stack trace for more information about the error and where it originated in the code.
Exception Details: System.Web.Services.Protocols.SoapException: Problem with SAP/BAPI. SAP.Connector.RfcCommunicationException: Connect to message server failed Connect_PM MSHOST=prddb01.lamrc.com, R3NAME=PRD, GROUP=Prod HR PRD LOCATION CPIC (TCP/IP) on local host ERROR service 'sapmsPRD' unknown TIME Wed May 04 08:59:06 2005 RELEASE 620 COMPONENT NI (network interface) VERSION 36 RC -3 MODULE ninti.c LINE 428 DETAIL NiPServToNo SYSTEM CALL getservbyname COUNTER 1 at SAP.Connector.SAPConnection.ThrowRfcException(RFC_ERROR_INFO_EX rfcerrInfo, Encoding encoding, String languangeCode) at SAP.Connector.SAPConnection.Open() at SAP.Connector.SAPClient.RfcInvoke(String method, Object[] methodParamsIn) at SAP.Connector.SAPClient.SAPInvoke(String method, Object[] methodParamsIn) at SoftwareKeySAPG.SAPProxy1.Z_Bapi_Load_Kpi_Region(ZSOFT_KPI_REGIONS_MTable& Kpi_Regions, ZSOFT_PROD_TYPETable& Prod_Type) at SoftwareKeySAPG.SAPGSK.LoadKPIRegion(DataSet dsProduct)
Source Error:
An unhandled exception was generated during the execution of the current web request. Information regarding the origin and location of the exception can be identified using the exception stack trace below.
Stack Trace:
[SoapException: Problem with SAP/BAPI.
SAP.Connector.RfcCommunicationException: Connect to message server failed
Connect_PM MSHOST=prddb01.lamrc.com, R3NAME=PRD, GROUP=Prod HR PRD
LOCATION    CPIC (TCP/IP) on local host
ERROR       service 'sapmsPRD' unknown
TIME        Wed May 04 08:59:06 2005
RELEASE     620
COMPONENT   NI (network interface)
VERSION     36
RC          -3
MODULE      ninti.c
LINE        428
DETAIL      NiPServToNo
SYSTEM CALL getservbyname
COUNTER     1
   at SAP.Connector.SAPConnection.ThrowRfcException(RFC_ERROR_INFO_EX rfcerrInfo, Encoding encoding, String languangeCode)
   at SAP.Connector.SAPConnection.Open()
   at SAP.Connector.SAPClient.RfcInvoke(String method, Object[] methodParamsIn)
   at SAP.Connector.SAPClient.SAPInvoke(String method, Object[] methodParamsIn)
   at SoftwareKeySAPG.SAPProxy1.Z_Bapi_Load_Kpi_Region(ZSOFT_KPI_REGIONS_MTable& Kpi_Regions, ZSOFT_PROD_TYPETable& Prod_Type)
   at SoftwareKeySAPG.SAPGSK.LoadKPIRegion(DataSet dsProduct)]
   System.Web.Services.Protocols.SoapHttpClientProtocol.ReadResponse(SoapClientMessage message, WebResponse response, Stream responseStream, Boolean asyncCall) +1503
   System.Web.Services.Protocols.SoapHttpClientProtocol.Invoke(String methodName, Object[] parameters) +218
   SoftwareKeyUI.InstalledBaseDataWS.InstalledBaseData.LoadKPIRegionMulti(DataSet products)
   SoftwareKeyUI.InstalledBaseDataAccess.LoadKPIRegionMulti(DataSet products)
   SoftwareKeyUI.InstalledBase.GetRegionDetails(Int32 userId, String product, String regionType)
   SoftwareKeyUI.FilteredAccess.GetRegionDetails(Int32 userId, String product, String regionType)
   SoftwareKeyUI.search.LoadRegionDetails()
   SoftwareKeyUI.search.regionType_SelectedIndexChanged(Object sender, EventArgs e)
   System.Web.UI.WebControls.ListControl.OnSelectedIndexChanged(EventArgs e) +108
   System.Web.UI.WebControls.DropDownList.System.Web.UI.IPostBackDataHandler.RaisePostDataChangedEvent() +26
   System.Web.UI.Page.RaiseChangedEvents() +115
   System.Web.UI.Page.ProcessRequestMain() +1099

The error is a very basic one - the sapmsPRD service is not known. You will have to go to <NT_ROOT>\system32\drivers\etc and add the entry sapmsPRD 3600 to this file.
This is basically telling the requester at what port to look for the message server.
C

Problem Please help me.....Let me know the area to look for it

Problem Please help me.....Let me know the area to look for it I am a DBA..Thanks in advance to let me know the cause and the area to look and fix it...
Server Error in '/' Application.
Problem with SAP/BAPI. SAP.Connector.RfcCommunicationException: Connect to message server failed Connect_PM MSHOST=prddb01.lamrc.com, R3NAME=PRD, GROUP=Prod HR PRD LOCATION CPIC (TCP/IP) on local host ERROR service 'sapmsPRD' unknown TIME Wed May 04 08:59:06 2005 RELEASE 620 COMPONENT NI (network interface) VERSION 36 RC -3 MODULE ninti.c LINE 428 DETAIL NiPServToNo SYSTEM CALL getservbyname COUNTER 1 at SAP.Connector.SAPConnection.ThrowRfcException(RFC_ERROR_INFO_EX rfcerrInfo, Encoding encoding, String languangeCode) at SAP.Connector.SAPConnection.Open() at SAP.Connector.SAPClient.RfcInvoke(String method, Object[] methodParamsIn) at SAP.Connector.SAPClient.SAPInvoke(String method, Object[] methodParamsIn) at SoftwareKeySAPG.SAPProxy1.Z_Bapi_Load_Kpi_Region(ZSOFT_KPI_REGIONS_MTable& Kpi_Regions, ZSOFT_PROD_TYPETable& Prod_Type) at SoftwareKeySAPG.SAPGSK.LoadKPIRegion(DataSet dsProduct)
Description: An unhandled exception occurred during the execution of the current web request. Please review the stack trace for more information about the error and where it originated in the code.
Exception Details: System.Web.Services.Protocols.SoapException: Problem with SAP/BAPI. SAP.Connector.RfcCommunicationException: Connect to message server failed Connect_PM MSHOST=prddb01.lamrc.com, R3NAME=PRD, GROUP=Prod HR PRD LOCATION CPIC (TCP/IP) on local host ERROR service 'sapmsPRD' unknown TIME Wed May 04 08:59:06 2005 RELEASE 620 COMPONENT NI (network interface) VERSION 36 RC -3 MODULE ninti.c LINE 428 DETAIL NiPServToNo SYSTEM CALL getservbyname COUNTER 1 at SAP.Connector.SAPConnection.ThrowRfcException(RFC_ERROR_INFO_EX rfcerrInfo, Encoding encoding, String languangeCode) at SAP.Connector.SAPConnection.Open() at SAP.Connector.SAPClient.RfcInvoke(String method, Object[] methodParamsIn) at SAP.Connector.SAPClient.SAPInvoke(String method, Object[] methodParamsIn) at SoftwareKeySAPG.SAPProxy1.Z_Bapi_Load_Kpi_Region(ZSOFT_KPI_REGIONS_MTable& Kpi_Regions, ZSOFT_PROD_TYPETable& Prod_Type) at SoftwareKeySAPG.SAPGSK.LoadKPIRegion(DataSet dsProduct)
Source Error:
An unhandled exception was generated during the execution of the current web request. Information regarding the origin and location of the exception can be identified using the exception stack trace below.
Stack Trace:
[SoapException: Problem with SAP/BAPI.
SAP.Connector.RfcCommunicationException: Connect to message server failed
Connect_PM MSHOST=prddb01.lamrc.com, R3NAME=PRD, GROUP=Prod HR PRD
LOCATION CPIC (TCP/IP) on local host
ERROR service 'sapmsPRD' unknown
TIME Wed May 04 08:59:06 2005
RELEASE 620
COMPONENT NI (network interface)
VERSION 36
RC -3
MODULE ninti.c
LINE 428
DETAIL NiPServToNo
SYSTEM CALL getservbyname
COUNTER 1
at SAP.Connector.SAPConnection.ThrowRfcException(RFC_ERROR_INFO_EX rfcerrInfo, Encoding encoding, String languangeCode)
at SAP.Connector.SAPConnection.Open()
at SAP.Connector.SAPClient.RfcInvoke(String method, Object[] methodParamsIn)
at SAP.Connector.SAPClient.SAPInvoke(String method, Object[] methodParamsIn)
at SoftwareKeySAPG.SAPProxy1.Z_Bapi_Load_Kpi_Region(ZSOFT_KPI_REGIONS_MTable& Kpi_Regions, ZSOFT_PROD_TYPETable& Prod_Type)
at SoftwareKeySAPG.SAPGSK.LoadKPIRegion(DataSet dsProduct)]
System.Web.Services.Protocols.SoapHttpClientProtocol.ReadResponse(SoapClientMessage message, WebResponse response, Stream responseStream, Boolean asyncCall) +1503
System.Web.Services.Protocols.SoapHttpClientProtocol.Invoke(String methodName, Object[] parameters) +218
SoftwareKeyUI.InstalledBaseDataWS.InstalledBaseData.LoadKPIRegionMulti(DataSet products)
SoftwareKeyUI.InstalledBaseDataAccess.LoadKPIRegionMulti(DataSet products)
SoftwareKeyUI.InstalledBase.GetRegionDetails(Int32 userId, String product, String regionType)
SoftwareKeyUI.FilteredAccess.GetRegionDetails(Int32 userId, String product, String regionType)
SoftwareKeyUI.search.LoadRegionDetails()
SoftwareKeyUI.search.regionType_SelectedIndexChanged(Object sender, EventArgs e)
System.Web.UI.WebControls.ListControl.OnSelectedIndexChanged(EventArgs e) +108
System.Web.UI.WebControls.DropDownList.System.Web.UI.IPostBackDataHandler.RaisePostDataChangedEvent() +26
System.Web.UI.Page.RaiseChangedEvents() +115
System.Web.UI.Page.ProcessRequestMain() +1099

Hi
You should make a mapping for the service sapmsPRD in your /etc/services file (On Windows: C:WINDOWSSYSTEM32DRIVERSETCservices). If your instance number is 00 you will have to add the following entry:
sapmsPRD 3600/tcp
Good luck!
René van Es

K8n neo4 boot problems ...please help!!

Similar Messages

Maybe you are looking for