K8N Neo4 Platinum + Barracuda 7200.9 HD--what transfer rates to expect?

My HD is SATA II set up as RAID0. I have only one HD in the system. What kind of transfer rate can I expect? I've run some benchmarks--3D Mark, PC Mark, SiSoft Sandra, and N-bench. I forget which one gave me the HD transfer rate, but the rate was 55 MB/sec. It seems like the HD should be faster than that.
Any comments would be welcome!
Bruce

Quote from: gr8nrg on 31-December-05, 02:15:11
Thanks syar2003!
That's what I wanted to hear. Yes, I have enabled 3gb transfer rate using Hitachi Feature Tool and I'm using Nvidia drivers. I am not sure how to enable NCQ in the Hitachi Feature Tool. I don't see that option there. Where is it? Only 3gb/s change and "spread spectrum" option, which, by the way should I enable it or not???
I'm going to go and check later if in the drivers tab I have NCQ enabled or not. And you're right, with MS drivers, you can't do that.
As far as RAID goes, even if I later add secomd SATA II drive, I've read several benchmarking articles that there is almost no improvement in real life performance (read: in games and apps) with RAID 0 setup over non-RAID setup with 2 separate drives, but twice as likely data loss, naturally.
This link has 3 references to reputable discussions
Am I right about those conclusions?
What people mean theoretically and what you personally feel running raid 0 is two seperate things.
Another thing is that reviewers always use large stripe size and this wont help for a mixed use with OS loaded on the raid.
OS on raid 0 need stripe size 16 or 32 as the partition is mostly filled up with smaller files and we want that files to split
on two drives over the raid.
I've been running raid0 since nforce2 , and running OS on single disk again feels like a performance loss for sure.
The fault tolerance thing is not an aspect as all I install on the raided volume can be reinstalled or imaged back .
Never lost a disk yet though , but had data corruption due to the non locked sata 1/2 on the nforce3 (cover yourself when OC'ing is wise).

Similar Messages

BSOD's on my x64 K8N Neo4 Platinum based PC, Any ideas what's wrong? Help!

Over the past few month I've been getting BSOD's. There is no real pattern to their occurence and it's not something which is constantly happening (It happened around 5 times in the past 2 months), but I've really grown to hate them. You see, after getting one what has happened in the past is that when I go to restart my pc after getting a BSOD, I find I need to re-install my whole OS! What happens is that after booting (which oddly enough doesn't work well after a BSOD, It freezes on the boot screen and I need to restart several times), a black screen appears telling me that certain files in the C:Windows\ direcotory are corrupt or missing.
So the real problem is that the BSOD's cause me to re-install my whole OS. One will happen, then it will be ok, I turn the system on, log into windows, then it might happen again, after which I'll need to re-install. The files that go missing are always different too, and when I run scan-disk (after plugging in my main drive into another computer) it finds corrupt files and deletes them.
At first I thought it was Azureus (p2p client) which was causing the problems because it seemed to happen when I was runing that. I stopped using it, and the BSOD's still occured...sometimes randomly when browsing...etc. I figured that since files got deleted and corrpupted, it must be a problem withthe Hard Drive....So I bought a new one, and I've still had the BSOD error (although files haven't been deleted yet).
So yeah, I really need to solve this problem as it is taking away from my productivity and causing me to re-install far too often. I will post the BSOD info as well as my system info below (and a screen shot):
Quote
MACHINE_CHECK_EXCEPTION
*** STOP: 0x0000009c (0x0000000000000004,0xFFFFF80000113BC0, 0x00000000B2000000, 0x0000000000070F0F)
I looked that up on the net, and it seems the first part seems to indicate, or at least COULD indicate overheating. I checked CPU and System temps and they seem acceptable.
I am running Windows XP x64 Edition with the following hardware (please note that all of the hardware drivers I'm using are written for x64, MSI is so good:)). I have had this PC before it started having these problems, it could be related to using x64 I guess, but the error doesn't show that does it?
Quote
AMD Athlon 64 3200+ 2.0 GHz Socket 939 (Venice Core) w/ stock heatsink/fan
MSI K8N Neo4 Platinum S-939 nForce4 Ultra
OCZ PC-3200 DDR400 Premier Series 1GB (2x512MB) Dual Channel Kit CAS 2.5
Ati Radeon x800xl 256MB gddr3, PCI-E
LG 17" L1720B LCD monitor 16ms, 1280x1024
Western Digital Caviar 120GB SATA
Western Digital Caviar SATA II (WD1600JS) 160GB 7200RPM 8MB Buffer
Western Digital Caviar SATA II (WD2500KS) 250GB 7200RPM 16MB Buffer
Pioneer DVR-109 DVD-RW
Pioneer DVR-110D DVD-RW
Antec Sonata II Mid tower ATX black power supply 450 Watt ( ATX12V 2.01 )
Creative I-Trigue 2.1 L3450 speakers
Sony 1.44MB Floppy Disk Drive
Microsoft multimedia keyboard and Microsoft optical mouse (PS/2)
My OS and drivers are fully updated. As for my BIOS I've been running the version I'm using now forquite some time and I believe it is version 1.5. Also in another bad turn of events, my northbridge fan seems to be on its way out of this world (this just happned so I don't think its related to the BSOD). I haven't been able to find a replacement, and since its not spinning very fast, and sometimes stops...It's causing the heatsink to get quite hot. I need to get a new one, and I can't find them anywhere...I wonder if thats covered under warranty... I looked into getting a different heatsink, but my Graphics card is so colse to this heatsink, that theres no room for a bigger one at all.
Do you think this problem is motherboard related, I cannot understand what the technical info the BSOD gives me means, can anybody understand it? I don't think its my HD's, or Ram, or CPU...could it be a motherboard problem? And if so, its under 1 year old, can I get an RMA?
Thanks for the help in advance.

At one time I had a weak 450w psu that had only 18a on the 12v rail. When I overclocked my cpu and gpu, I was getting bsod's every once in a while and couldnt figure it out until I read a similar post like yours on this forum. I decided to upgrade my psu and havent had that problem since.
Power supplies can be deceiving. I now have a 480w psu but its has 30a on the 12v rail. So what we need to know is the ratings of your psu (see my sig) just to see if your psu is the culprit. Just my 2 cents.

PSU Dead and MOBO K8N Neo4 Platinum SLI Too, what can i do???

Yerterday i was sleeping and suddenly the PSU (Rosewill RP550) Blow away, I Inmediatly check the PSU and guess what? Fried!!! Then i went to sleep again to check the other components in the mourning. The next Mourning i took my old PSU and put an 20 to 24 pin adapter, placed it in the mobo and doesn´t work, next i put a friend PSU with 24 pin connector and nothing, next i test 2 or 3 PSUs more and nothing. After all this tests i started thinking that the mobo was having electrical issues. I went to a friend house and tested the processor ( AMD 3000+ CBBID 0505) and the Memory (OCZ Rev2 1GB), they worked. I couldn´t test the Video Card (MSI 6600GT 128MB) because i dont have any other mobo to check it.
Its Important to tell you guys that when i try to plug the PSU power conector to the MOBO the Fans and network led start for 1 second, then turn off, i try to start the computer and nothing happend. All this with the four PSUs.
A friend of mine which is a computers Technician told me that took off the MOBO batery, CPU and Memory and put Aluminiun foil all over and around the mobo to eliminate any static on it. What do yo think about this??
Please if you have any suggestion, i´ll be happy.
BTW: Which are the procedures to RMA both componnets ? I bough the mobo and PSU and the others components on www.newegg.com on May 09 2005.
Thanks for all.

Got my Newegg RMA board back (K8N Neo4 Platinum SLI) today! I mailed it to them Friday, they got it Monday and a replacement back to me today. Excellent turnaround
The board looks like it was refurbished because the anti-static bag was a bit wrinkled and had pinholes all over one section where the board couldn't have caused it. Also, it had bios 3.0 on it! The rest of the stuff in the board looks new but it didn't come with the USB 2.0 bracket which the first board I got did. Live and learn.
I flashed it to 3.2 and all appears to be working. Not gonna try 3.3. I read somewhere that there may be a beta 3.5 bios out somewhere. Maybe I'll wait till that one goes final.
Haven't had any experience with MSI support as far as RMA's but if this replacement board craps out I'll try them next.

IDE cables bundled with K8N Neo4 Platinum--80 wire or 40 wire?

Is the rounded IDE cable that comes with the K8N Neo4 Platinum (non-SLI) mobo an 80 wire or 40 wire cable? How can one tell?
I think I may be having some UDMA issues with my second hard drive (120GB Barracuda 7200.7 IDE). I installed XP on my SATA drive with no other drives connected and then added this IDE drive.
The rest of my setup is in my sig.
Thanks!
Bruce

OK. I checked my device manager for the info on my IDE drive. I looked at the properties of NVIDIA nForce4 Parallel ATA Controller.
Primary Channel:
HD Model # is ST3120026A. The drive set up as Ultra DMA 5 - Ultra 100. Checked boxes are "Let BIOS select transfer mode, Enable read caching, and Enable write caching. I did a speed test from Windows and it shows Theoretical limit of 100, Burst speed of 86.3 and Sustained speed of 58.1.
Secondary Channel:
DVD: _NEC DVD_RW ND-3540A. Transfer mode is Ultra DMA2 - Ultra 33. This is using a flat ribbon cable from an older computer. The only box checked is "Let BIOS select transfer mode".
Do these both look OK or do I need to change something?
Then I looked at the properties of NVIDIA nForce4 ADMA Controller and found:
My SATA drive (my boot drive) is HD model # ST3160812AS. Transfer mode is PIO Mode. Boxes checked are "Enable read caching, Enable write caching, and Enable command queuing. There is a yellow triangle that says "Transfer mode downgraded". I can't do a speed test.
What do I need to do to operate in Serial ATA Generation 2 - 3G? This is how this drive is supposed to operate.
Thanks!
Bruce

No Post - K8N Neo4 Platinum SLI - any help would be awesome

Ok here it goes. I recently bought a K8N neo4 SLI and set everything up, hit the power button, and nothing happened. So i figured it was DOA and i sent it back. got another one, hooked it up and nothing happened. Tested the PSU and power switch on a different machine and they work fine. But with the K8N i have nothing, no fans, no lights, nada. I am a relatively experienced computer builder and haven't had this one happen to me yet. I've read every troubleshooting guide on the MSI site and i think everyone in the forums but the dang thing still won't turn on. Here the specs:
K8N Neo4 Platinum SLI
Athlon 64 3200+ 90nm
512 x 2 Geil Ultra Platinum DDR 533
Seagate SATA HD 7200 RPM 160 GB
Chaintech 6600GT
Ultra X-connect 500W with the 24-pin adapter
Got a bunch of other junk too but thats all thats hooked up now. just going for the bare minumums so i could at least get some response. Please give me some ideas of what could be causing this are maybe something dumb i forgot. I know my power suppply blows but i've seen others get it going with that and since i only have barebones hooked to it, i'd think it would go. Thanks in advance.

I had an interesting thing happen to me yesterday, that sounds exactly like your problem.
I'm looking for ways to reduce my gpu temps, so I'm playing around with case fans, round wiring, etc... One of the cables I replaced ran to one of my PCI-E cards. aparently it had a short or something in it. I spent hours trying to get my computer to start up again, I was afraid I had fryed the board....no power, no fans, tried a different power supply, etc..... One wire, well two, because it's one of those that takes two molex plugs and turns them into a Pci-e plug.
What a pain....
Chack your wires, check for a short. If you're having the same issue with a second mobo chances are it's not board related. Could be you have the srews attaching it to your case to tight and have shorted it out there.
Hope this helps.
Good luck!

SATA drives not being detected - K8N Neo4 Platinum

I have the same problem, different PSU!
msi k8n neo4 platinum pcb 1.0
3000 64 939
corsair 1gb dual channel ddr400
nvidia 8800gts
antec truepower 550 (19a @ 12v)
used to run 2 ide maxtor 120 and 80
added in a sata dvd writer, worked for 6 months
added in a sata 1TB seagate 7200, sata fails a majority of the time
same symptons now persist as in original post.
:< either bios detects both sata drives, neither, or it crashes. this happens respectively rarely, uncommon, and most common
what ive tried:
updated all mainboard, bios, video drivers to the most up to date (i had to in order for bios to detect the full size of the 1TB)
no ide, same problems
only 1 sata, with and without ide, same problems
the sata only works after a long period of time (or randomly), that i dont use it
(ive had both sata unplugged for 12 hours, booted up this morning with them and it detected, i selected safe mode boot, after making it through a majority of the load, it crashed)
testing a new psu in a day or so, much more powerful. ill give you all my results.

The cables aren't overly bent?
"...worked for 6 months"
"...fails a majority of the time"
Not very relevant, but since i found the FAQs, and there are no less than four FAQs for hard disks http://global.msi.com.tw/index.php?func=prodfaq&maincat_no=1&cat2_no=&cat3_no=&prod_no=165#menu :
"Silicon Image Si3114R Raid bios doesn't have JBOD setting in it, why?
In the new Silicon Image BIOS, JBOD already been renamed as "Concatenation".
If you want to use single SATA HDD or when tou want use each SATA HDD as IDE mode, you can choose "Concatenation" function in Silicon RAID BIOS."
"I am using a SATA hard drive with NCQ technology on this motherboard and I am experiencing problems. How do I fix it?
The issue depends on the Southbridge chipset. Nvidia is currently working on an updated nForce driver to address the issues with certain hard drives.
You could contact Nvidia support to ask for the new driver if there is one. If there is not any new driver to solve the issue, please disable NCQ on your system." /My fattening. /

Multiplier ? K8N Neo4 Platinum

Got this rig to POST the other night, installed W2KPro SP4, all seemed well. Last night I installed Prime, Sandra CPUZ etc. Parts are all still on the bench. I should mention that I'm using a $10 PCI Video card for posting, troubleshooting etc. I can only display in 16 colors. I don't know if this would make a difference. I started foolin around Ocing this thing, upped the FSB speed from 200 to 220, upped the CPU voltage up slightly, didn't fool w/any RAM timings or change anything else. The machine will boot to Windows, and CPUZ shows the overclock(220 10X). Given my CPU stepping and this mobo, I fully expected Prime to fail, which it did, promptly. I've read here that I can drop the multiplier to say 9 for example to reach a more stable OC that way. I just don't know how. I'm also unclear on Ocing the RAM, but perhaps I'll post on that later.Thanks
Present build
MSI K8N Neo4 Platinum
Athlon 64 3200+ (Winchester) CBBID
Artic Cooling Freezer 64 w/AS5
2X 512 Kingston Value KVR400X64C3
EVGA 6800GT
2X Seagate Barracuda 80G SATA HDDs
Antec 480 Neo Power
ASUS® P4PE Mainboard, (Intel®82845PE Chipset)
2.4Ghz Pentium® 4 Northwood core, @ 2.52Ghz
512Mb Samsung® 3200 400DDR RAM
ASUS® V8420 128Mb DDR GeForce® 4 Video card (NVidia Ti 4200)
Creative Labs Audigy® 5:1 Sound Card (OEM) w/ Firewire.
Happauge® PVR250 video capture card
2X Maxtor® DiamondMax® 60G HDDs, (7200 RPM 2 MB cache)
Lite-On® 16X DVD, Lite-On® 48X CDRW
330W Antec® Tru-Power PSU
Antec® PlusView 880 AMG Full Tower case, (painted, candy apple metallic blue).
Stock Intel® HSF, 5- 80mm case fans. Stealthed optical drives, subtle light mod.
PowerMac® G4 1.25GHz
Toshiba Satellite® Notebook 1.2 Ghz Celeron

set ram ratio to 166, as for the multiplier look for something called CPU ratio, also you probably need to drop the HTT down to atleast 4

MSI K8N Neo4 Platinum SLI sound needs -5V; newest Antec 550W has no -5V rail

I came within a whisker of ordering a non-returnable 3700 Venice, MSI K8N Neo4 Platinum SLI mobo and an upgraded Power Supply, Antec's newest 550W PS the TP2-550 EPS12V ($117). This has dual 2x24pin 12V 19A rails and is touted as the new V2.0 EPS12V/ATX12v compatible power supply for high performance SLI systems. By accident I came across a page at MSI for this mobo
http://www.msi.com.tw/program/products/mai...ail.php?UID=641
At the end is this warning: MSI Reminds You...
• For this model, you must use a Power Supply which has a -5V pin supply. Also, the users manual which I downloaded on Pg 2-10 says the same thing
The above Antec PS specs do not show a -5V rail, nor does an Enermax 600W I looked at. The V2.0 specs for ATX12v which added 2x24pin 12V rails dropped -5V rail from the spec and it appears MSI is not conforming to the spec (See Antec response at end) None of the web sites selling these PS & mobos contain any warning. I vaguely recall from a forum a while back it may have something to do with the Soundblaster system in the mobo.
http://www.antec.com/us/productDetails.php?ProdID=22551 (click specifications)
Isn't this a major showstopper which is going to cause a lot of grief for those of us upgrading to SLI systems using this mobo and upgrading our PS to the newest & best power design? We won't know the PS won't work until we build the system.
Regards, Ron
Antec reply to me:
>>>>Thanks for the link. Since MSI's website does state the motherboard needs the -5v, the True550EPS12V will not work with this motherboard. The Standard (http://enhanceusa.com/documents/atx12v_v2.01.pdf) has removed the use for the -5v rail and it is no longer needed. MSI has not manufactured that motherboard to the Standard. Finding an ATX12V v2.0 power supply with the -5v might be hard to find. You should contact MSI for a compatibility list of power supplys that were tested to work with the K8N SLI Platinum.

Quote from: ccve3 on 21-May-05, 07:27:40
Wow!! syar2003 thanks for that post. I've spend an hour going through it & fasteddies links. Now I are a power expert. The dual rail argument is enough for me to go back to the MSI K8N Neo4 Platinum SLI with one of the single rail PS -5V units listed by fasteddie. The only question left now refers to computerpro3 recommendation on ultra power supplies for SLI
>>I quite simply wouldn't dream of putting anything else in my machine. Keep in mind, this section is for 2x 6800 models, not the 6600's which most any good psu will handle (like Antec Neopower, ocz 520, etc). . Pc Power and Cooling 510 Deluxe SLI edition (refer to list)
2. Zippy/Emacs 550-700w models
3. OCZ 600w (personally I would get the pcp&c for the price, but it's been proven here, so I'll be fair...).
These are really high end, expensive and only 3-4 choices. Since I'm getting one 6800GT and eventually another & possibly eventually a 4800 X2, I was hoping the OCZ 520W would do it but computerpro3 says Powermaster 520 isn't good enough for SLI. I found that there is an OCZ 600W ATX12 dual rail which surprisingly has a -5V rail needed for K8N Neo4 SLI Soundblaster. Will this meet computerpro3's preference for a high end PS for SLI systems even though I'm losing the 1 rail advantage. Maybe the 600 Watts just overwhelms the 1 rail/2 rail question.
Thanks again for the teriffic help
Regards, Ron
Wondering what you settled on. I got the Antec TP550 and it's flawless on the board. I even have the older 20pin model which works perfectly (including sound). If you really wanted what I would consider to be a top dog (pcpower and cooling), and find the -5v rail missing, all you have to do is place a phone order and request they add a -5v rail. It's a minimal cost and a total solution for having everything. Just my $0.02

K8N Neo4 Platinum (PCB 1.0) and AMD 64 3800+ X2

Help!
I have a K8N Neo4 Platinum (PCB 1.0) and it had an AMD 64 3200+ single core CPU.
Now I've upgraded to an AMD 64 3800+ X2 dual core but the BIOS and MS Vista are seeing only the one core.
The BIOS is at the latest version - 1.D.
Whats' going on?
Hitch.

Quote from: hitchhiker on 20-April-07, 08:44:57
This motherboard does support the X2 CPU right?
It's listed as supported on the MSI website but has nayone else got both cores running on it?
Hitch.
Yes it does support X2
Did you clear cmos with power cable disconnected from psu?
Look at my signature for link to proper method.

K8N Neo4 Platinum, how to move MBR to sata (make it drive #1)?

I am not sure I am phrasing the question correctly, so bear with me. I have a K8N Neo4 platinum with the SiI3114 controller and sata ports 4-8 (I believe its what they are calling PCB 1.x) with bios v1.D. I moved the board to another box and installed winXP on it. I was running it with IDE hard drives. Everything was working great but the OS was running really slow so I bought a SATA 300 mb/s drive and pluged it into SATA1 (I read about using ports 3 and 4 for raid but I do not want to use the NVraid at all, it is disabled). Then I proceeded to reinstall win XP. In the setup, I deleted the original C partiton and created one on the sata drive and rebooted so that there would be no "C" drive confusion by the winxp setup (have had that problem before and this keeps it from happening). Went through the setup and the sata was correctly reported as "C". Told windows to install itself there but it told me that it needed to write to MBR on the old c drive but that, since I had deleted the partiton, it couldn't and had to format it. So I knew that something was wrong.
So I rebooted and disabled the ide bus that contained the old IDE drive and just left the CD ide bus enabled. WinXP installed fine with no complaints. Then it rebooted and I re-enabled the ide bus in the bios. It wouldn't boot into the partiton I just installed winxp on! To get it to boot, I had to use F11 (the bios boot menu) and select the sata drive. Went through the whole setup winXP thing and rebooted. Same problem, it wouldn't boot the sata drive. :(
As long as that ide bus with the old ide drive is enabled, it won't boot the sata drive! I have rearranged the boot order on the bios every way possible. I opened up the box and moved that ide chain with the old ide drive to the ide2 port and put the dvd drive on ide1. I made the old drive slave and the prior slave master. That didn't fix it either. How do I tell this motherboard that the 1st drive is the sata drive? How do I tell it the MBR should be there not on the old ide drive? How do I fix this? Thanks!

Thank you for your replies! Hans, thank you I will give it a go again doing full formats all the way. I usually use the full format when installing winXP but I did things in a different order than you instructed so I will definately try it.
Aicjofs, thank you, There are 3 hard drives in this system currently. There is the ide hard drive that used to be the "c" drive (a western digital 160gb ata133 7200rpm 8mb cache) and a second ide hard drive that is an extended partition with 1 logical drive with data on it (western digital 300gb ata133 7200rpm 8mb cache). Then there is a sata hard drive in sata1 port with 2 partitions one primary and one extended. The extended partion does have data on it as I moved stuff there after I got winXP up the 2nd time (western digital 250gb sata II 7200rpm 16mg cache). Right now, I have the ide drive with data on it as ide2 master and the old "c" drive as ide2 slave and it is unformatted and contains no partion information (I deleted the partition after I installed the SATA drive and installed winXP). XP won't boot. What happens is that, if I take the winxp cd out, it gives me a "no system" error. If I leave the WinXP cd in it boots that disk. However, if I use "f11" and choose to boot the sata drive, winxp comes up just fine. If I disable the ide bus with the two ide hard drives, it boots winxp just fine.
Edit: bios is v1.D. It feels like this mobo is telling windows setup that the master ide drive is the first disk and to ignore everything else. It feels like if I can just tell the mobo that the sata drive is the first disk then everything will work . It is late night where I am now, and I've been fighting with this since the afternoon so I might have to goto sleep but I will be back at it tomorrow and will go though what Hans instructed. If anyone has any otehr ideas, I'd really appreciate that as well.

Strange power-on (issue?) with K8N Neo4 Platinum

Hi all, i have a new K8N Neo4 Platinum, non-sli.
My rig:
A643000+ winch, no overclock
2x512MB Corsair XMS DDR400MHz
2x200GB Seagate mirroring
Plextor PX-708A
BenQ DVD Burner
AN OLD Matrox Mystique 4MB PCI (new pci-e gfx card later...)
A powerfull enermax coolergiant 600W ATX 2.0 power supply
Latest official nforce4 drivers and bios
It seems to be ok: installed winXP pro sp2 and updates, installed two Seagate in raid-mirroring with the nforce4 controller, installed some progs and utils, firewall is ok, prime95 go without problems for 1 our (more tests later), cpu temp is 34°C and sys temp is 30°C.
CoreCenter Say:
Vcore -> 1.41V
3.3V -> 3.39V
+5V -> 5.13V
+12V -> 12.26V
memory volt -> 2.60V
FSB -> 200MHz
PCI-E -> 100MHz
cpu volt -> By-VID
Apparently no weird things...
When i switch-on the Pc, for some seconds( ̃10 secs) it don't want to boot, optical drives blink repeatly and the screen is blank, like a bad overclock... But the machine isn't overclocked, and the bios is ok, i think. After 10 secs, finally it go and run flawlessly, post and other things are ok. When i reboot in win, the 10secs-issue repeat itself. So this strange thing at the post is normal? Anyone with the same "problem"? For now the rig is ok when it logon in winXP...

Hi all my friends
@JER101 >>> Ehrr i mean post, sorry
I had unplugged the optical drives, but the problem persist. When plugged, they blink for some times and after blinking the machine go into post-phase and after it boot in the correct manner. I think the PCI card is the problem, like some of you said... I will buy one pci-e card (obviously), but i hope things are not dangerous for now
In the mean time, i have a new problem: emule+firewall=BSOD. I know, there are tons of post about this issue around, but the solution is unclear... Tried to disable DEP, patched WinXP SP2 with latest things from winupdate, but nothing work for me, emule and the firewall generate a crash&reboot. Tried with the Marvell LAN, too, without success.
Any suggestions? Usefull links? If i uninstall the "NVIDIA Forceware Network Access Manager" it will work without problem with a thirdy part firewall, like sysgate?
P.S.
What's the problem with nvidia drivers? C'mon nvidia, solve this damned issue!

Firewire/1394 devices are not auto-detected with k8n neo4 platinum

I am unable to detect firewire/1394 devices to my PC through my K8N Neo4 Platinum. That is, I plug in the device through the firewire port and windows doesn't detect that a device has been plugged in.
I have tried:
-2 firewire devices, both are Canon digital camcorders (ZR10 and ZR25MC)
-2 different firewire cables
-reinstalling windows, got all windows updates except
(Microsoft Base Smart Card Cryptographic Service Provider Package: x86 (KB909520))
-patch from microsoft, discussed here
(https://forum-en.msi.com/index.php?topic=81749.0)
-both firewire devices using both cables connect just fine to a test computer
-both my computer and the test computer have Windows XP Pro SP2
Windows doesn't make the noise "bah-dum" that it has detected a device, nor does it display the dialog that gives me options of what programs to use. Once in a while, if I leave it connected for a while and come back, windows will eventually find it...or windows might bog down and get really slow. It speeds up again instantly once I unplug the firewire device. Strange, I know. Also there are NO conflicts in device manager.
Could it be?:
-bios misconfiguration
-need to use an older chipset driver (i am using most recent from nvidia.com)
-onboard audio or front audio needs to be disabled
-the k8n neo4 platinum simply has connection problems with some firewire devices
(i hope not)
Bob

Built2Last: (good questions!)
I tried your suggestion by removing PCI cards and made FURTHER progress. I found out that my firewire card, the Syba NEC1394-P3, has some compatibility issues with my other PCI cards. I found this out because:
1. it worked fine after I placed it in a non-comm (orange) slot and removed my soundcard (X-Fi) and Belkin wireless modem, and
2. a tech support representative from Syba told me that that particular firewire card has compatibility issues
Quote
Also, SD-NEC-4F is our older model firewire card.
Our new firewire card (SD-PCI-4F) is using VIA VT6306 chipset and no customer complain about any installation issue so far.
If the SD-NEC-4F still giving you trouble, I'll suggest you to return it and exchange for the SD-PCI-4F firewire card.
At least he is honest and wants to help, so I remain impartial towards Syba.
So I figured out the firewire card, but not the onboard firewire. Ok, but check this out! When the Syba card was working, I could plug in BOTH the external hard drive AND either of the Canon camcorders to the Syba firewire card. Windows all three devices just fine. Again, the onboard firewire would ONLY detect JUST the external hard drive, but would not detect either of the Canon camcorders. It seems as though the ball again is knocked back into MSI's court on this issue. Any ideas?
syar2003:
As for drivers, I checked for drivers for: onboard firewire, add-in firewire card, and Canon camcorders.
-I cannot find where there is an MSI firewire driver for my onboard firewire port. I originally guess that it was part of my chipset driver installer, but the README doesn't say anything about it. It is also not an additional download on MSI's website. But since it detects an external hard drive I figure I must already have it.
-The add-in firewire card does not have drivers. I repeat, they do not exist. The manual and Syba's website both state that drivers for the card are included all versions of Windows back to Windows 98.
-Canon's website has a driver/software download page but it also appears that drivers do not exist for the Canon camcorders.
Yes the camcorder is set to VCR mode.
Yes the IEEE1394 is correctly installed, since external hard drive connects okay.
I tried two DV cables and both are connected fine.
The camcorders do not support USB as far as I can see, and if they do, I'm not using it.

MicroStar K8N Neo4 Platinum 54G - nForce4 Ultra Avilability in CZ

Hi all,
does anybody know when M/B MicroStar K8N Neo4 Platinum 54G - nForce4 Ultra will be avilable in Czech Republic (Europe)??? I'm waiting two months for it...

Not really (maybe AC97 Controller = Auto was the closest). But, I tried now to switch the LAN cable to the upper RJ-45 slot instead of the lower one, and it seem to have stopped the power on peculiarity. Now only if I could pinpoint what's the broken component that causes the boot screen freeze and what causes the 35-45s idle time at the Win-logo loading screen.
The freaky boot screen freeze happens something like this:
1. the mother board model number is shown
2. the CPU information is shown (or sometimes this is skipped and not shown)
3. here it may or may not freeze and usually it produces this terrible out of sync mess (and monitor has to be switched off to get it back to normal)
I don't see any connection to overheating, I never touched any overclocking settings (or any other settings for that matter, it's a 2-day old installation).

K8N Neo4 Platinum

I purchased this board in May of 2005 and I am looking to upgrade the processor.
The MSI web site specs say that the board is X2 ready but doesn't state what processors it supports. What X2 processors does it support?
The web specs also state that the board supports up to a 4000+ processor. Has this changed and does it now support faster processors that are not shown on the web specs?
MrNeil

MrNeil,
Did you look here?
K8N Neo4 Platinum CPU Support Status
Take Care,
Richard

Difference between K8N Neo4 Platinum/SLI and K8N-SLI Platinum

Hey guys.... I have one question and i hope you can help me.
I'm about to get an MSI SLI Platinum motherboard, but it seems that there are two versions, the K8N Neo4 Platinum/SLI and the K8N-SLI Platinum.
What is the real difference between them? As i can see in the manual, the Neo4 version has the additional SATA2 and Gbit LAN controller.
Anyone: Does your K8N-SLI board have 4 or 6 SATA2 ports? and 1 or 2 LANs?
At this picture http://www.midtdata.dk/asp/index.asp?varernr=K8N-SLI-PLAT&goto=productinfo&mainfunc=link I can see that there are 6 blue SATA connectors (lower right corner), and 2 LAN ports left to the LPT port... But the description says 4 SATA and 1 LAN, and so says the manual.
To all owners of this mobo: Does this picture look like your K8N-SLI Platinum or does it look like your K8N Neo4 Platinum/SLI ?

https://forum-en.msi.com/index.php?board=36.0
d/l a raid manual and all should be clear

K8N Neo4 Platinum + Barracuda 7200.9 HD--what transfer rates to expect?

Similar Messages

Maybe you are looking for