K8N Neo4 Platinum & FX-55 - Refusing to post

For some reason I can't get my system to post. The power goes in, but there are no beeps. This only started after I changed the FSB on my FX-55 to 215HZ to get 2800MHZ (it's a ClawHammer with a very early week number). When I first restarted after making the changes in the BIOS, the system would post but when I went into the BIOS to check the temperature I would just see the flashing underscore and nothing more. Restarting again and now I have nothing. I've plugged in the D-Bracket and it gets to "Initializing Video Interface: This will start detecting the CPU clock, checking type of video onboard. Then detect and initialize the video adapter". I've tried removing the graphics card, which gets it to "Initializing Floppy Drive Controller" (which it hangs at that point). I have tried a different graphics card, but then it goes back to step one (the video interface part).
I have tried resetting the CMOS via the switch and I have also left the battery out for about 10 minutes while the power is off and with the capacitors dry - still no go.
Should I leave the battery out for longer or is there any other way to get this to work? I've tried reseating the CPU too - no go.

Problem found - dead NIC in a PCI slot.

Similar Messages

No Post/Black Screen - MSI K8N Neo4 Platinum

Hello,
Here is my problem, I bought MSI K8N Neo4 Platinum motherboard and got
- 3500+ cpu
- CORSAIR XMS 1GB memory
- PCI-E Leadtek 7800GT video card
- Aspire 520Watt PSU
I have put all of it together fine( I have put many systems for friends before) hooked all the power cables, case to mobo stuff, fans. Every time I turn it on fans go on, and lights go on but there is nothing on the screen as if no signal from video card to monitor, plus no error beeps which means cpu and memory is fine right. I have tried to just have memory, video card and nothing else hooked up, same result. I have tried another PSU, same result. Now to add to this, I had same problem with ABIT motherboard and another video card(same) which eliminates bad motherboard and bad video card, since both I have replaced except this time I got MSI mobo and not ABIT. I got same problem with all of it, nothing comes up, no post while fans spin when I turn it on etc... What could be the problem? memory? case? Any ideas?
Please help me as I spent a lot of $ and time on this and had no signal to monitor so far. Thanks.

As I said at this point I am trying to boot without any drives plugged in just to get a post and boot up but no go. So basically all my drives are unplugged and I cannot get it to work, I have tried different psu and same problem. I have tried another video card( I RMA this one and got another) it goes and snaps into PCI E slot all good, I have checked that many times. The only thing I can think of is memory at this point but this is brand new XM Corsiar memory and why wouldnt the motherboard beep ( i hoked speaker) if there was any error like that? I just dont get what is going on.
I have no idea what bios version I have as I have been unable to check it, unless you want me to check the chip version on chipset?

K8N Neo4 platinum edition v1 (bios W7125NMS V1.6 062305) -- after POST stucked

hi i'm runningan athlon 3000+ in K8N Neo4 platinum edition v1 (bios W7125NMS V1.6 062305) and i have a very like problem:
today i tried to install freebsd(install started fine, nothing went wrong, i repartioned my hdd and the installer started),
for some reason i had to abort the installation process. since then i can not boot in from any device(cd,usb the hdd is in a
half way to bsd install state so it's not an option atm).
the post screen comes up and i can interact with it in a way(i can press tab and it drops me
to the detailed post screen,ctrl-alt-del also works i can restart with it), but i neither can enter to the BIOS setup /DEL/ nor the boot menu /F11/.
i've tried reseting bios settings by flushing cmos(removed the battery,pressed SW1. something must happened because the post now checks for sata devices
and the graphical screen/that one u can bypass by pressing TAB/ was not presented before).
it also detects my hdd and my cd-rom too. but still nothing happens after the POST.
others said updating my bios would help. but still there is no option to boot from.
if i am doing wrong something please let me know,
thank you for your help
Andrew

the solution:
disable ide1/slave when the broken hdd is not connected and bios accessible; poweroff; reconnect the broken hdd to the PC;poweron; boot from a linux livecd; gpart/fdisk/something to repair the broken hdd;be happy life is nice
the trick was that bios and post is not messing with the broken hdd(while it was blocked in the bios)
so i could boot with a live cd when my hdd was connected to the PC.
since linux trixx out bios i was abel to interact with the post_killer_hdd (even it was blocked in the bios).
i hope somebody will be able to use it one day if something is not understandable drop me a PM.
problem solved im installing the os to the hdd,topic is SOLVED.
maybe the other guy who has some similar issues with his config/hdd could use this post too.
regards,
/\ndrew

K8N Neo4 Platinum Wont POST please help!!

ok, i built this pc about a month ago. everything has worked perfectly until yesterday. When i turn the power on, al i get is the Platinum Screen. I cant go into Bios, i cant Post.. The PC beeps once like normal, and the LED on the Motherboard and the videocard come on. Ive tried wiping the CMOS, Tried a different PSU, tried removing one of the memory sticks. I tried just connecting the Mobo, video card and harddrive, to see if it want getting enough power. Heres what ive got:
K8N Neo4 Platinum/SLI
Athlon 64 3500+
Geforce 6800 Gt
1 Gig corsair 3200 ram (2x512mb)
550 watt PSU

reset the bios, make sure its RESET.
then, try with just 1 stick ram first.
remember, to run dual for this board, it has to be Slot 1 & Slot 2.
If u follow the color, it'll be single channel instead.
Read also the instruction, it says never plug into 2nd or 4th slot with 1 stick ram.
Try with 1 stick ram. if it boots, then insert the 2nd into Slot 2. for dual channel.
i had similar prob few days back when newly purchased.
good luck !

K8N Neo4 Platinum Ultra nForce4 no post.

Took the cpu off and cleaned it, upgraded the video card started the computer and no post. Led's 1,3,4, green 2 red. Took cpu out and checked it no bent pins, checked all connections. Sometimes when it boots it will have 4 green led's but no video. Tried another vid card same thing. Tried booting and holding the insert, cont+home, F1, delete keys. Get power to the fans and hear the HDD sometimes.
Specs.
MSI K8N Neo4 Platinum Ultra nForce4 bios v1.6
Athlon 64 3700+ San Diego Core
Geil value ram
1-36GB Raptor
, M45 Powercolor Radeon X800 GT PCI-EX 256MB DDR3 R480 Core
XP.Pro.W/SP.2
X-Connect 500W ATX PSU
+5V +3.3V +12V -12V -5 +5VSB
30A 28A 34A .8 .3 2
Edit: Have cleared the cmos many times. If I boot holding the insert key down for a while I get 1,3,4, leds red 2 green, if I then push F1 they all turn green but still no vid.

No posts to your post either LOL
Anyway - could be fans causing it - I had my Neo not booting until I disconnected a case fan from the mobo fan header output.
Try with just leaving the cpu fan (could also be this one of course) .

No Post - K8N Neo4 Platinum SLI - any help would be awesome

Ok here it goes. I recently bought a K8N neo4 SLI and set everything up, hit the power button, and nothing happened. So i figured it was DOA and i sent it back. got another one, hooked it up and nothing happened. Tested the PSU and power switch on a different machine and they work fine. But with the K8N i have nothing, no fans, no lights, nada. I am a relatively experienced computer builder and haven't had this one happen to me yet. I've read every troubleshooting guide on the MSI site and i think everyone in the forums but the dang thing still won't turn on. Here the specs:
K8N Neo4 Platinum SLI
Athlon 64 3200+ 90nm
512 x 2 Geil Ultra Platinum DDR 533
Seagate SATA HD 7200 RPM 160 GB
Chaintech 6600GT
Ultra X-connect 500W with the 24-pin adapter
Got a bunch of other junk too but thats all thats hooked up now. just going for the bare minumums so i could at least get some response. Please give me some ideas of what could be causing this are maybe something dumb i forgot. I know my power suppply blows but i've seen others get it going with that and since i only have barebones hooked to it, i'd think it would go. Thanks in advance.

I had an interesting thing happen to me yesterday, that sounds exactly like your problem.
I'm looking for ways to reduce my gpu temps, so I'm playing around with case fans, round wiring, etc... One of the cables I replaced ran to one of my PCI-E cards. aparently it had a short or something in it. I spent hours trying to get my computer to start up again, I was afraid I had fryed the board....no power, no fans, tried a different power supply, etc..... One wire, well two, because it's one of those that takes two molex plugs and turns them into a Pci-e plug.
What a pain....
Chack your wires, check for a short. If you're having the same issue with a second mobo chances are it's not board related. Could be you have the srews attaching it to your case to tight and have shorted it out there.
Hope this helps.
Good luck!

K8N Neo4 Platinum SLI memory incompatibility

Sorry if it is an duplicated post, but i'm in a hurry and can't find nothing about this subject.
I'm sure i'm not the first to have this problem.
My memory (Samsung DDR 400Mhz - 512Mb) does not work on my MB. Though a friend of mine has a generic type 256 and it works just fine. With my memory the computer doesn't turn on, and start that beeping thing...
I hope you guys won't worry about bad english (I'm brazilian).
Thanks.

Hi again,
Well, if your RAM works fine on that computer, you can do some things to clear things up between your RAM and your Mainboard. You will need your friend's RAM once more to do this, as yours refuses to work yet:
1. First of all, and I know it seems a little dumb, make sure your RAM is installed correctly. As you may know by now, DDR RAM only fits in one way. If installed correcly, you should barely see the gold contacts of your RAM.
2. Try to find out if your RAM is supported by your K8N Neo4 Platium, by reading the Test Report :
http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_trp_detail.php?UID=637
If SAMSUNG memory is listed there, it will appear as "SEC". Please note however, that many memory manufacturers use SAMSUNG chips for their memory sticks, so it may be a memory stick made by Kingston, Corsair, GoldenRAM, Spectek, etc. or even be a Generic Brand.
3. If you have not updated your K8N Neo4 Platium BIOS yet, this could be a good time to do it. Be sure to:
* Find, download and use ONLY the correct BIOS for your mainboard. For that look for it by using two IDs: The Mainboard Model (K8N Neo4 Platium ) and the mainboard Model Number (MS-????). You will find these numbers between the PCI slots of your mainboard, write them exactly as they appear there and then look for a BIOS update for that specific model.
* Prepare, in a NEW floppy disk, a BIOS rescue disk, just in case something go wrong during the process. To do so, please read : http://www.msi.com.tw/html/support/bios/note/boot.htm
* Be sure to disable any BIOS WRITE PROCTECT function your board may have. It could be a hardware protection (via jumper) or a software protection (via BIOS)
If its a hardware protection, set your jumper to WRITE ENABLE. If a software protection, set the BIOS WRITE PROTECT feature to DISABLED. If you can't find this feature, or don't know where are they located, please check your mainboard manual for it, and follow the instructions to disable the BIOS WRITE Protection, before attempting to flash the new BIOS.
* Run the BIOS update from a DOS prompt if possible. For that, use a NEW floppy disk, as old disks may just fail in the middle of the operation and you may end with a useless mainboard.
* Do not power off or reset your PC during this process or you may also end with a useless mainboard.
* If you can connect your computer to a working UPS before attemping to flash the new BIOS, it would be great, as it will continue to supply power to your computer in the remote event of a power failure (Blackout or "Apagon" in spanish)
* VERY IMPORTANT : Let the process to FINISH by itself. It may take a while, but please do not reset or power off your PC. Just power of or reset your computer ONLY when the Flash Utility directs you to do so.
4. Once you have flashed the most recent BIOS to your K8N Neo4 Platinum mainboard, try your memory again. It may work now. If it doesn't then you could be right about some incompatibility between your RAM and your mainboard.
For now this is all I can suggest you. It doesn't appears to be a Power Supply Unit (PSU) related problem as your mainboard works well with your friend's RAM.
Well I hope this helps a little.
Good luck!

MSI K8N Neo4 Platinum SLI sound needs -5V; newest Antec 550W has no -5V rail

I came within a whisker of ordering a non-returnable 3700 Venice, MSI K8N Neo4 Platinum SLI mobo and an upgraded Power Supply, Antec's newest 550W PS the TP2-550 EPS12V ($117). This has dual 2x24pin 12V 19A rails and is touted as the new V2.0 EPS12V/ATX12v compatible power supply for high performance SLI systems. By accident I came across a page at MSI for this mobo
http://www.msi.com.tw/program/products/mai...ail.php?UID=641
At the end is this warning: MSI Reminds You...
• For this model, you must use a Power Supply which has a -5V pin supply. Also, the users manual which I downloaded on Pg 2-10 says the same thing
The above Antec PS specs do not show a -5V rail, nor does an Enermax 600W I looked at. The V2.0 specs for ATX12v which added 2x24pin 12V rails dropped -5V rail from the spec and it appears MSI is not conforming to the spec (See Antec response at end) None of the web sites selling these PS & mobos contain any warning. I vaguely recall from a forum a while back it may have something to do with the Soundblaster system in the mobo.
http://www.antec.com/us/productDetails.php?ProdID=22551 (click specifications)
Isn't this a major showstopper which is going to cause a lot of grief for those of us upgrading to SLI systems using this mobo and upgrading our PS to the newest & best power design? We won't know the PS won't work until we build the system.
Regards, Ron
Antec reply to me:
>>>>Thanks for the link. Since MSI's website does state the motherboard needs the -5v, the True550EPS12V will not work with this motherboard. The Standard (http://enhanceusa.com/documents/atx12v_v2.01.pdf) has removed the use for the -5v rail and it is no longer needed. MSI has not manufactured that motherboard to the Standard. Finding an ATX12V v2.0 power supply with the -5v might be hard to find. You should contact MSI for a compatibility list of power supplys that were tested to work with the K8N SLI Platinum.

Quote from: ccve3 on 21-May-05, 07:27:40
Wow!! syar2003 thanks for that post. I've spend an hour going through it & fasteddies links. Now I are a power expert. The dual rail argument is enough for me to go back to the MSI K8N Neo4 Platinum SLI with one of the single rail PS -5V units listed by fasteddie. The only question left now refers to computerpro3 recommendation on ultra power supplies for SLI
>>I quite simply wouldn't dream of putting anything else in my machine. Keep in mind, this section is for 2x 6800 models, not the 6600's which most any good psu will handle (like Antec Neopower, ocz 520, etc). . Pc Power and Cooling 510 Deluxe SLI edition (refer to list)
2. Zippy/Emacs 550-700w models
3. OCZ 600w (personally I would get the pcp&c for the price, but it's been proven here, so I'll be fair...).
These are really high end, expensive and only 3-4 choices. Since I'm getting one 6800GT and eventually another & possibly eventually a 4800 X2, I was hoping the OCZ 520W would do it but computerpro3 says Powermaster 520 isn't good enough for SLI. I found that there is an OCZ 600W ATX12 dual rail which surprisingly has a -5V rail needed for K8N Neo4 SLI Soundblaster. Will this meet computerpro3's preference for a high end PS for SLI systems even though I'm losing the 1 rail advantage. Maybe the 600 Watts just overwhelms the 1 rail/2 rail question.
Thanks again for the teriffic help
Regards, Ron
Wondering what you settled on. I got the Antec TP550 and it's flawless on the board. I even have the older 20pin model which works perfectly (including sound). If you really wanted what I would consider to be a top dog (pcpower and cooling), and find the -5v rail missing, all you have to do is place a phone order and request they add a -5v rail. It's a minimal cost and a total solution for having everything. Just my $0.02

MSI K8N Neo4 Platinum or MSI 6600GT PCI-E ?

Dear Sirs,
I've just bought a MSI NX6600 TD GT 128MB PCI-E and
Motherboard MSI K8N Neo4 Platinum.
I Think that one of these is defective bacause WinXP
can't work with MSI original drivers, MSI old
drivers or Nvidia drivers. The system reboots.
I think that i've tried almost everything and this
card only works badly with VesaSave driver (Generic
Windows driver).
Could a defective video card works ?
Is it possible that the problem is the Motherboard ?
Any idea ?
Help me please,
Thank you very much,
ISW
MSI K8N Neo4 Platinum
A64 3500+ Winchester
Original Cooler
DDR PC4000 GEIL 1GB ULTRA DUAL
MSI NX6600 TD GT 128MB PCI-E
Maxtor 120GB
Seagate 120GB
XP Home SP2

Duplicate Post.
Look for all replies here:
MSI 6600GT PCI-E or MSI K8N Neo4 Platinum ?
Take Care,
Richard

BSOD's on my x64 K8N Neo4 Platinum based PC, Any ideas what's wrong? Help!

Over the past few month I've been getting BSOD's. There is no real pattern to their occurence and it's not something which is constantly happening (It happened around 5 times in the past 2 months), but I've really grown to hate them. You see, after getting one what has happened in the past is that when I go to restart my pc after getting a BSOD, I find I need to re-install my whole OS! What happens is that after booting (which oddly enough doesn't work well after a BSOD, It freezes on the boot screen and I need to restart several times), a black screen appears telling me that certain files in the C:Windows\ direcotory are corrupt or missing.
So the real problem is that the BSOD's cause me to re-install my whole OS. One will happen, then it will be ok, I turn the system on, log into windows, then it might happen again, after which I'll need to re-install. The files that go missing are always different too, and when I run scan-disk (after plugging in my main drive into another computer) it finds corrupt files and deletes them.
At first I thought it was Azureus (p2p client) which was causing the problems because it seemed to happen when I was runing that. I stopped using it, and the BSOD's still occured...sometimes randomly when browsing...etc. I figured that since files got deleted and corrpupted, it must be a problem withthe Hard Drive....So I bought a new one, and I've still had the BSOD error (although files haven't been deleted yet).
So yeah, I really need to solve this problem as it is taking away from my productivity and causing me to re-install far too often. I will post the BSOD info as well as my system info below (and a screen shot):
Quote
MACHINE_CHECK_EXCEPTION
*** STOP: 0x0000009c (0x0000000000000004,0xFFFFF80000113BC0, 0x00000000B2000000, 0x0000000000070F0F)
I looked that up on the net, and it seems the first part seems to indicate, or at least COULD indicate overheating. I checked CPU and System temps and they seem acceptable.
I am running Windows XP x64 Edition with the following hardware (please note that all of the hardware drivers I'm using are written for x64, MSI is so good:)). I have had this PC before it started having these problems, it could be related to using x64 I guess, but the error doesn't show that does it?
Quote
AMD Athlon 64 3200+ 2.0 GHz Socket 939 (Venice Core) w/ stock heatsink/fan
MSI K8N Neo4 Platinum S-939 nForce4 Ultra
OCZ PC-3200 DDR400 Premier Series 1GB (2x512MB) Dual Channel Kit CAS 2.5
Ati Radeon x800xl 256MB gddr3, PCI-E
LG 17" L1720B LCD monitor 16ms, 1280x1024
Western Digital Caviar 120GB SATA
Western Digital Caviar SATA II (WD1600JS) 160GB 7200RPM 8MB Buffer
Western Digital Caviar SATA II (WD2500KS) 250GB 7200RPM 16MB Buffer
Pioneer DVR-109 DVD-RW
Pioneer DVR-110D DVD-RW
Antec Sonata II Mid tower ATX black power supply 450 Watt ( ATX12V 2.01 )
Creative I-Trigue 2.1 L3450 speakers
Sony 1.44MB Floppy Disk Drive
Microsoft multimedia keyboard and Microsoft optical mouse (PS/2)
My OS and drivers are fully updated. As for my BIOS I've been running the version I'm using now forquite some time and I believe it is version 1.5. Also in another bad turn of events, my northbridge fan seems to be on its way out of this world (this just happned so I don't think its related to the BSOD). I haven't been able to find a replacement, and since its not spinning very fast, and sometimes stops...It's causing the heatsink to get quite hot. I need to get a new one, and I can't find them anywhere...I wonder if thats covered under warranty... I looked into getting a different heatsink, but my Graphics card is so colse to this heatsink, that theres no room for a bigger one at all.
Do you think this problem is motherboard related, I cannot understand what the technical info the BSOD gives me means, can anybody understand it? I don't think its my HD's, or Ram, or CPU...could it be a motherboard problem? And if so, its under 1 year old, can I get an RMA?
Thanks for the help in advance.

At one time I had a weak 450w psu that had only 18a on the 12v rail. When I overclocked my cpu and gpu, I was getting bsod's every once in a while and couldnt figure it out until I read a similar post like yours on this forum. I decided to upgrade my psu and havent had that problem since.
Power supplies can be deceiving. I now have a 480w psu but its has 30a on the 12v rail. So what we need to know is the ratings of your psu (see my sig) just to see if your psu is the culprit. Just my 2 cents.

Constant HDD access (K8N Neo4 Platinum)

Hello all, this is my first time posting on these forums.
A couple of days ago I put together a new system for myself, with the following components:
* Athlon64 3200+ processor
* MSI K8N Neo4 Platinum motherboard
* 1Gb RAM
* Gigabyte 128Mb GeForce 6600GT graphics card
* 2x Seagate 250Gb 7200rpm SATA drives
* LG IDE dual-layer DVD-RW drive
* Apacer 7-in-1 internal USB 2.0 card reader
* Thermaltake "soprano" ATX midi-tower w/ 400W PSU
The two hard drives I have connected to ports SATA5 and SATA6 on the motherboard and set up in a RAID1 configuration (using the on-board Silicon Image SiI 3114 RAID controller). I then installed Windows XP Professional, which went on fine. The only problem I have now is that the hard drives are being constantly accessed by the system, even when I'm doing nothing on the system. This isn't just an occasional access once every second or so, the little HDD LED just flickers away merrily the whole time. I have run both filemon and diskmon on the system, and found that while no particular files appear to be being accessed, there is almost constant write activity being performed to the hard drives.
I have narrowed it down to somehow involving the Windows XP RAID drivers. If I boot from the Windows XP install disk and load the third party drivers for the SiI 3114, I get the constant disk access when sitting at the first screen of the install process ("Welcome to Windows XP" text-only screen). If I do the same without loading the drivers (thus Windows does not recognise the RAID drive), no disk access. I have tried updating the RAID controller drivers under the Device Manager (now up to version 1.2.0.0), but it does not fix the problem. I have done a full virus and spyware scan (bearing in mind that this is a clean install), with no results. I have checked all running processes and services (including making sure Indexing Service is not running), but have been unable to find anything that could be causing this constant activity. I have yet to try actually breaking the mirror and running the drives off the normal SATA controller. I will be trying that tonight when I get home if no other solution presents itself, but obviously I would rather get it behaving properly in RAID1 if at all possible.
It's driving me crazy. There doesn't appear to be any actual issues with the performance of the machine, but the constant hard disk activity can't be good for the drives long-term. I have searched these forums for a possible solution, and while some people have had similar problems, none of the suggested solutions have worked for me so far. If anyone can help me with my dilemma, I would be Eternally Grateful(tm).

Yes! At least I'm not alone... constant disk ticking is driving me nuts too.
I have same issue with a newly built system - different board but Sil3114.
My C: is on the NF4 SATA interface, but I have 4 250GB Seagaets on the Sil3114, intended for a RAID5 array. Having installed XP, I've become distracted by the constant disk access and have been trying everything to eliminate it before proceeding with the rest of the build - nogo. Your post gave me the clue - boot with Sil3114 disabled = no disk activity; boot with enabled = constant disk flogging.
I've got the Sil driver up to 1.2.3.1 but no better. Suspect it may be the Sil3114 BIOS that needs upgrading but seems no way to flash it - have you got anywhere with your debugging?
Appreciate a solution before I go crazy with the tick, tick tick....

Strange power-on (issue?) with K8N Neo4 Platinum

Hi all, i have a new K8N Neo4 Platinum, non-sli.
My rig:
A643000+ winch, no overclock
2x512MB Corsair XMS DDR400MHz
2x200GB Seagate mirroring
Plextor PX-708A
BenQ DVD Burner
AN OLD Matrox Mystique 4MB PCI (new pci-e gfx card later...)
A powerfull enermax coolergiant 600W ATX 2.0 power supply
Latest official nforce4 drivers and bios
It seems to be ok: installed winXP pro sp2 and updates, installed two Seagate in raid-mirroring with the nforce4 controller, installed some progs and utils, firewall is ok, prime95 go without problems for 1 our (more tests later), cpu temp is 34°C and sys temp is 30°C.
CoreCenter Say:
Vcore -> 1.41V
3.3V -> 3.39V
+5V -> 5.13V
+12V -> 12.26V
memory volt -> 2.60V
FSB -> 200MHz
PCI-E -> 100MHz
cpu volt -> By-VID
Apparently no weird things...
When i switch-on the Pc, for some seconds( ̃10 secs) it don't want to boot, optical drives blink repeatly and the screen is blank, like a bad overclock... But the machine isn't overclocked, and the bios is ok, i think. After 10 secs, finally it go and run flawlessly, post and other things are ok. When i reboot in win, the 10secs-issue repeat itself. So this strange thing at the post is normal? Anyone with the same "problem"? For now the rig is ok when it logon in winXP...

Hi all my friends
@JER101 >>> Ehrr i mean post, sorry
I had unplugged the optical drives, but the problem persist. When plugged, they blink for some times and after blinking the machine go into post-phase and after it boot in the correct manner. I think the PCI card is the problem, like some of you said... I will buy one pci-e card (obviously), but i hope things are not dangerous for now
In the mean time, i have a new problem: emule+firewall=BSOD. I know, there are tons of post about this issue around, but the solution is unclear... Tried to disable DEP, patched WinXP SP2 with latest things from winupdate, but nothing work for me, emule and the firewall generate a crash&reboot. Tried with the Marvell LAN, too, without success.
Any suggestions? Usefull links? If i uninstall the "NVIDIA Forceware Network Access Manager" it will work without problem with a thirdy part firewall, like sysgate?
P.S.
What's the problem with nvidia drivers? C'mon nvidia, solve this damned issue!

XP64bit installation halts, K8N Neo4 Platinum - No SATA drives found?

My setup:
Athlon 64 3500+
K8N Neo4 Platinum
2GB OCZ 3200 Premier
2) WD Sata 80GB HD's (for RAID 0)
Nvidia 6800GT Extreme VGA
I was recently lucky enough to get my hands on a real Windows XP Pro64bit Extended Edition. I gathered quite a few 64bit drivers which claim to do the job (so they say.)
However I ran into a very strange issue during installation.
My main concern was getting RAID drivers to utilize after pressing F6 during the Windows install. Unfortunately I could not find Nvidia drivers so I went with the Silicon Image Sil3114 64bit drivers I got from their website. Copied them to a disk and thought I was ready to rock N roll. I have updated all BIOS to latest versions as of the date of this post.
Now I went into the RAID BIOS and setup my RAID 0 Array and both SATA drives are shown. All went well in this dept.
I began my installtion of XP64 and pressed F6 to install the RAID drivers. Popped the floppy in and the driver files were copied successfully.
I continued on to the point where you are prompted to setup Windows XP and it searches for any previous installs.
I continue to where I should get the dislmaimer and to press F8, however the install halts and say no hard drives were found. Setup cannot continue.
Any ideas as to why my drives are not being detected during installation? They show up fine under the RAID setup BIOS.
Any info or thoughts is truly appreciated.

You need to make your own floppy for the nvidia 64 ide drivers.
How to install Windows on SATA using F6 to load Drivers
Follow item 1 Obviously usinfg the Neo4 64bit unified driver pack Windows XP Professional x64 Edition
luck

Problem replacing K8n Neo4 Platinum

Hello everybody, this is my first post here, I am a new member from Italy.
I have this problem:
I own a K8n Neo4 Platinum and when I changed the VGA from Nvidia 6600 GT to 8600 GTS the Mobo doesn't post anymore.. The usb diagnostig bracket says it's a memory problem but when I've put my memory banks on a different PC, they work just fine.
I think the problem was caused by the little space that I had between the VGA and the chipset cooler (Zalman passive);when I installed the VGA I damaged the chipset. Taking a closer look at it I noticed that 1 edge is damaged. I also substituted the Power suplly but the result is always the same.
So I decided to replace the mobo but I don't want to reinstall windows. Finding my same mobo is impossible here in Europe. I only found the K8n Neo4-F.
My question is the following :
-Does this Mobo use the same drivers that were installed on my HD? (latest driver downloaded from Nvidia version 6.86)
-Will I have problems with Windows ?

Massi186,
Moan Guide
Richard

Please Help K8N Neo4 Platinum won't boot?

Hello,
I could use your expertise in this matter. I have built several systems and never seen this before. My system will not boot with the hard drive
and/or DVD drive attached. It will boot with just the 1.44 floppy attached. My system is as follows:
MSI K8N Neo4 Platinum ATX AMD Motherboard
connect3D 3038 Radeon X800GTO 256MB 256-bit GDDR3 VIVO PCI Express x16 Video Card
Rosewill RV500S-2 500W Power Supply 500W ATX 2.01
+3.3v- 30A
+5V - 45a
+12V1 - 18a
+12V2 - 16a
AMD Athlon 64 3000+ 1GHz FSB Socket 939 Processor
CORSAIR ValueSelect 1GB (2 x 512MB) 184-Pin DDR SDRAM Dual Channel Kit System Memory
Cas Latency 2.5
Voltage 2.5V
Unbuffered
Windows XP professtional Service Pack 2
I tried resetting CMOS, changing the cmos battery, re-setting the video card, moving memory modules (from positions 1&2 to 3&4). The power supply is working. When I put my hard drive into another system it boots perfectly. Please help!
Thanks
Tony

All that info and I still don't know where you are plugging them in. SATA or IDE(PATA)? Both?
Can you describe the not booting a little more? i.e. No video at all, you see POST but it doesn't complete, POST completes but you can't boot an OS.

K8N Neo4 Platinum & FX-55 - Refusing to post

Similar Messages

Maybe you are looking for