K8N Neo4 Platinum "Initializing Floppy Drive Controller" problem

When I finished building my system a couple days ago I started it up and found some problems:
First of all I got a long beep and one or two (not really clear) short beeps (this can be a video issue but also a mainboard issue (?)), the computer continues to start up and ends without any screen on my monitor (it switches to standby mode) and the famous(?) "Initializing Floppy Drive Controller" LED combination.
This is what I tried so far:
-1- clean startup (cpu, 1 stick of memory, videocard) reinstalled all components
-2- boot without floppy drive
-3- clear CMOS
-4- tried different memory and different slots
-5- disabled all case usb and firewire options
I am using a PS/2 Keyboard but it seems to work because when I hit the numlock key the green LED comes on.
What should be my next step?
System specs:
Cooler Master Cavalier 3
Fortron FSP400-60THN PSU
MSI K8N Neo4 Plat.
AMD64 3000+ (winchester)
2 x Corsair VS512mb400
HIS X700 Pro 128 mb
Samsung 1614C 160 Gb SATA
PS/2 Keyboard
USB Mouse

Quote from: Wonkanoby on 15-February-05, 20:04:01
http://www.fsp-group.com.tw/english/02_products/01_pc_power_supply.asp?modelid=166&modelname=FSP400-60THN
14a max 12v is not going to run your set up
Thanks for your reply!
I thought this was enough:
+12V1DC : 14,0A
+12V2DC : 15,0A
--------------------------- +
29,0A
Or is this not the correct way to calculate?

Similar Messages

K8N Neo4-F "Initializing Floppy Drive Controller" problem

Hello there,
I read the other posts on this topic but the problem is that I dont even get as far as the BIOS.
I get to that looks a lot like something from a grfx card.
And then nothing. Initially I did not have the a FD connected but it is the same with it.
1. Old 350W ATX 20pin
2. 20 to 24 pin ATX
3. MSI K8N Neo4-F
4. AMD Athlon 64 3000+ socket 939
5. MSI NX7100GS (PCI-e grfx)
6. Corsair 512MB
7. Corsair 1024 MB
8. 2xPATA 80GB
9. 2xSATA 160GB
My previous mobo crashed and after some misunderstandings 2,3,4 and 5 are new and the others are old stuff.
Any help appreciated. I can probably get model numbers from the rest of the components. Let me know if you need it (just did not think it was relevant and yes I am quite lazy)
"A forum is not a Christmas tree - please skip the animated avatars"

Quote from: Grayone on 21-March-07, 04:53:26
Have you tried another power supply? Most 350 watt power supplies do not produce enough 12volt power to run Athlon 64 processor based systems.
I was afraid of this ... the previous processor was an Athlon 64 2800+ but an AGP gfx card. might be the problem ... could anyone confirm this before I buy a new power supply?

P35 Platinum ... Initializing Floppy Drive Controller ?? (Wont Boot)

Hi all
I have built a new comp for someone who wants reliability so i choose to go Platinum, but ... i cant make it boot.
It wont even show ANYTHING on the screen (tried the vga in both Pci-e 16x just in case i was dumb enough lol) the boot "procces" stops with the Status leds showing:
4) Green
3) Green
2) RED
1) Green
According to the user guide it says:
Initializing Floppy Drive Controller.
This will initialize floppy drive and controller.
And i dont even have a floppy
Well as the problem persisted i removed EVERYTHING from the motherboard
now i left:
-Mother
-Processor
-Memory
-VGA
-PSU
And thats it. Let me tell you all the things i tried:
-Bios reset (with the little red button)
-Plug only necesary things
-Taking off the battery and replacing it (and went back to the "original")
-Tried different connectors just in case it was the PSU (i really dont think so)
-Tried different memory stick/s.
And well, thats all i think, half of this i did it with the mother in the case, and re-did all the list with the moter OUTSIDE the case. Can anybody help me ??
I guess is a BIOS problem, as i readed in another post (yeah used search first xD) but the only guy who could solve the problem was flashing the bios, but i cant even see a word on the screen, is it possible to flash the bios in my condition ??
The specs now:
Intel C2D E4500
MSI P35 PLATINUM
2x1Gb (or 1x1gb, tried single sticks as well) OCZ DDR2 667mhz (and tried also with generic "titan" memory at 800mhz, does not change anything)
Gigabyte 8400GS
POWERCOOLER PS-500 SS PSU
AFAIK i have more than enough to make this boot, but well ... you know
Thanks in advance, i tried to give all details possible, in 2 days ill go to RMA if i cant make it work, but i would like give it a try, who knows
EDIT: my english sucks really bad, forgive me !!
EDIT2: Forgot to add !! when i remove the VGA the motherboard DOES the "VGA ERROR BEEP" and the leds are in the correct combination for VGA ERROR ... so i guess processor works and ram too (both OCZ and generic), if one of these fails then it wont make any sound, m i wrong ??

ITS ALIVE !!!!!!!!!!!!!
Well, to be honest, i dont know what it really was but tried 2 things:
First i followed step by step and word by word the "clearing CMOS" guide (this mobo has a button and not a juper, so i pressed the button like 2 minutes to be REALLY sure xD), then i realized that it was not doing the "beeps" anymore, but the screen was black like before.
SOOOOOOOOOOOO THEEEEEEEEN ... (shoot me in the head for this) i unplugged the video and keyboard from the KVM switch (could THIS be the problem ?? i used it wit hundreds of computers and never gave me prblems before ??? ??? ???) and plugged the cables directly and now its alive !!!
THANKS !! :D :D :D :D :D
One last thing !!
Do you recommend me to upgrade the BIOS ?? the board always did a "false boot" then starts normally, i readed it was some "hardware checking" feature, its that true or its totally useless ??
THANKKKKKKKKKKKKKKSSSSSSSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSS SSSSSSSSSS =) (im so damn happy now LOL)

[K8N Neo2] "initializing floppy drive controller"

Hi,
My mobo is always staying at this step.
I can't access to bios since this problem
I tried clearmos, changed graphic card, turn off hard drive and CDROM and floppy.
What's happen ? Is my mobo dead ?
Thx.

hi grabin,
welcome to the forum. for us to help you better please post details of your build including power supply details, follow the datails in my signature for guidance.
see Follow Initializing Floppy Drive Controller Link for some initial help.
luck

XP64bit installation halts, K8N Neo4 Platinum - No SATA drives found?

My setup:
Athlon 64 3500+
K8N Neo4 Platinum
2GB OCZ 3200 Premier
2) WD Sata 80GB HD's (for RAID 0)
Nvidia 6800GT Extreme VGA
I was recently lucky enough to get my hands on a real Windows XP Pro64bit Extended Edition. I gathered quite a few 64bit drivers which claim to do the job (so they say.)
However I ran into a very strange issue during installation.
My main concern was getting RAID drivers to utilize after pressing F6 during the Windows install. Unfortunately I could not find Nvidia drivers so I went with the Silicon Image Sil3114 64bit drivers I got from their website. Copied them to a disk and thought I was ready to rock N roll. I have updated all BIOS to latest versions as of the date of this post.
Now I went into the RAID BIOS and setup my RAID 0 Array and both SATA drives are shown. All went well in this dept.
I began my installtion of XP64 and pressed F6 to install the RAID drivers. Popped the floppy in and the driver files were copied successfully.
I continued on to the point where you are prompted to setup Windows XP and it searches for any previous installs.
I continue to where I should get the dislmaimer and to press F8, however the install halts and say no hard drives were found. Setup cannot continue.
Any ideas as to why my drives are not being detected during installation? They show up fine under the RAID setup BIOS.
Any info or thoughts is truly appreciated.

You need to make your own floppy for the nvidia 64 ide drivers.
How to install Windows on SATA using F6 to load Drivers
Follow item 1 Obviously usinfg the Neo4 64bit unified driver pack Windows XP Professional x64 Edition
luck

K8N Neo4 Platinum - Is It Dead? ***PROBLEM SOLVED***

I recently upgraded my system and moved most of the old components into a different case, including the K8N, CPU, memory and PSU. The only thing that is changing is the hard drive. When I power on the computer the D-Bracket indicates it is hanging at memory initialization. I have OCZ PC3200 platinum edition 2gb dual channel kit installed. I tried to boot with one stick installed in each slot and it still hangs at the same place. I fear I shorted or damaged the MB somehow... Any ideas?
Thanks,
Kurt

Quote from: Markoul on 09-April-09, 23:13:09
I know it sounds grazy... but unplug computer from wall socket for 10 seconds (cut power completely)
and try again.
You thank me later...
I wish it were true...no dice.

K8N Neo4 Platinum, how to move MBR to sata (make it drive #1)?

I am not sure I am phrasing the question correctly, so bear with me. I have a K8N Neo4 platinum with the SiI3114 controller and sata ports 4-8 (I believe its what they are calling PCB 1.x) with bios v1.D. I moved the board to another box and installed winXP on it. I was running it with IDE hard drives. Everything was working great but the OS was running really slow so I bought a SATA 300 mb/s drive and pluged it into SATA1 (I read about using ports 3 and 4 for raid but I do not want to use the NVraid at all, it is disabled). Then I proceeded to reinstall win XP. In the setup, I deleted the original C partiton and created one on the sata drive and rebooted so that there would be no "C" drive confusion by the winxp setup (have had that problem before and this keeps it from happening). Went through the setup and the sata was correctly reported as "C". Told windows to install itself there but it told me that it needed to write to MBR on the old c drive but that, since I had deleted the partiton, it couldn't and had to format it. So I knew that something was wrong.
So I rebooted and disabled the ide bus that contained the old IDE drive and just left the CD ide bus enabled. WinXP installed fine with no complaints. Then it rebooted and I re-enabled the ide bus in the bios. It wouldn't boot into the partiton I just installed winxp on! To get it to boot, I had to use F11 (the bios boot menu) and select the sata drive. Went through the whole setup winXP thing and rebooted. Same problem, it wouldn't boot the sata drive. :(
As long as that ide bus with the old ide drive is enabled, it won't boot the sata drive! I have rearranged the boot order on the bios every way possible. I opened up the box and moved that ide chain with the old ide drive to the ide2 port and put the dvd drive on ide1. I made the old drive slave and the prior slave master. That didn't fix it either. How do I tell this motherboard that the 1st drive is the sata drive? How do I tell it the MBR should be there not on the old ide drive? How do I fix this? Thanks!

Thank you for your replies! Hans, thank you I will give it a go again doing full formats all the way. I usually use the full format when installing winXP but I did things in a different order than you instructed so I will definately try it.
Aicjofs, thank you, There are 3 hard drives in this system currently. There is the ide hard drive that used to be the "c" drive (a western digital 160gb ata133 7200rpm 8mb cache) and a second ide hard drive that is an extended partition with 1 logical drive with data on it (western digital 300gb ata133 7200rpm 8mb cache). Then there is a sata hard drive in sata1 port with 2 partitions one primary and one extended. The extended partion does have data on it as I moved stuff there after I got winXP up the 2nd time (western digital 250gb sata II 7200rpm 16mg cache). Right now, I have the ide drive with data on it as ide2 master and the old "c" drive as ide2 slave and it is unformatted and contains no partion information (I deleted the partition after I installed the SATA drive and installed winXP). XP won't boot. What happens is that, if I take the winxp cd out, it gives me a "no system" error. If I leave the WinXP cd in it boots that disk. However, if I use "f11" and choose to boot the sata drive, winxp comes up just fine. If I disable the ide bus with the two ide hard drives, it boots winxp just fine.
Edit: bios is v1.D. It feels like this mobo is telling windows setup that the master ide drive is the first disk and to ignore everything else. It feels like if I can just tell the mobo that the sata drive is the first disk then everything will work . It is late night where I am now, and I've been fighting with this since the afternoon so I might have to goto sleep but I will be back at it tomorrow and will go though what Hans instructed. If anyone has any otehr ideas, I'd really appreciate that as well.

K8N Neo4 Platinum & FX-55 - Refusing to post

For some reason I can't get my system to post. The power goes in, but there are no beeps. This only started after I changed the FSB on my FX-55 to 215HZ to get 2800MHZ (it's a ClawHammer with a very early week number). When I first restarted after making the changes in the BIOS, the system would post but when I went into the BIOS to check the temperature I would just see the flashing underscore and nothing more. Restarting again and now I have nothing. I've plugged in the D-Bracket and it gets to "Initializing Video Interface: This will start detecting the CPU clock, checking type of video onboard. Then detect and initialize the video adapter". I've tried removing the graphics card, which gets it to "Initializing Floppy Drive Controller" (which it hangs at that point). I have tried a different graphics card, but then it goes back to step one (the video interface part).
I have tried resetting the CMOS via the switch and I have also left the battery out for about 10 minutes while the power is off and with the capacitors dry - still no go.
Should I leave the battery out for longer or is there any other way to get this to work? I've tried reseating the CPU too - no go.

Problem found - dead NIC in a PCI slot.

Building K8N Neo4 Platinum/SLI with A64 3200+ Venice

Well, almost. I have already received some of the parts, with the remainder expected to arrive on or before Wednesday, May 11, 2005. I've been planning this build for months, while collecting the necessary funds, & it will be nice to finally build this Gaming PC.
The system build will be as shown in my sig below. I have read, & plan to follow, the assembly & troubleshooting suggestions listed in this forum's stickies. A giant "THANK YOU" to fafner, who did a great job collecting all of this info for us. Hopefully, things will go smoothly & I won't run into any major issues.
I plan to post my progress & any issues/questions on this forum. Would it be best to do all of my follow-up posting in this thread, or should I start new threads for specific issues/questions?
Once the building project is complete, I could document the entire project, with photos, on my web site. Do you think that anyone would be interested or perhaps benefit from this?

First barebones boot successful. Started right up, all fans working, keyboard & video working, installed memory (1GB) correctly identified.
D-Bracket showed
Initializing Floppy Drive Controller
which is at is should be, since I had no drives hooked up.
It's been a long day. I need to stop & eat. I may continue after I eat, but I probably won't get very far until tomorrow.

Memory Controller not available - K8N NEO4 Platinum Ultra

Hi Experts!
I have typical problem in my PC. I need reply only from experts. Newbies please excuse.
My system displays the following info in POST.
VENDOR / DEVICE CLASS DESCRIPTION IRQ
===================================
10DE 005E 0580 Memory Controller NA
If anyone can correctly PIN POINTEDLY identify why this is displayed, it will be much helpful
As such I face no difficulty with my system. But this message very much annoys me.
Thanks.
My PSU Details:
400W. +12V 20Ampere. (This is the maximum I could afford in our indian PC environment.)
AMD 3000+ Winchester 90nm. CPU.
K8N NEO4 Platinum Ultra Mother Board.
512 MB Hynix PC3200 Memory. (2*256)
80GB Western Digital.
Ordinary PCI VGA 2mb card.
Samsung CDROM.

There is no driver for memory controller with A64 (nforce3/4) as stated earlier .
You see this in the memctrl.inf for UDP 5.10 , driver pack for nforce 3 and backwards down to nforce 1 .
Memctrl is only added to the 5.10 package for backward support to nf2 and lower as this is a unified driver package and
the memory controller is at chipset level on the motherboard that resides in the external northbridge on nf2 chipsets and lower .
What you see is just a vendor/machine id description and is just as it should be .
Code: [Select]
; nvmemctl.INF
; Copyright (c) 2001-2002, NVIDIA
; Version 1.00
[Version]
Signature="$WINDOWS NT$"
Class=System
ClassGuid={4D36E97D-E325-11CE-BFC1-08002BE10318}
Provider=%NVIDIA%
CatalogFile=nvmemctl.cat
DriverVer = 04/27/2004, 4.4.0
[ControlFlags]
ExcludeFromSelect=*
[Manufacturer]
%NVIDIA_MFG%=NVIDIA_SYS
[SourceDisksFiles]
[NVIDIA_SYS]
%PCI\VEN_10DE&DEV_01AA.DeviceDesc% = NO_DRV, PCI\VEN_10DE&DEV_01AA
%PCI\VEN_10DE&DEV_01AB.DeviceDesc% = NO_DRV, PCI\VEN_10DE&DEV_01AB
%PCI\VEN_10DE&DEV_01AC.DeviceDesc% = NO_DRV, PCI\VEN_10DE&DEV_01AC
%PCI\VEN_10DE&DEV_01AD.DeviceDesc% = NO_DRV, PCI\VEN_10DE&DEV_01AD
%PCI\VEN_10DE&DEV_01EA.DeviceDesc% = NO_DRV, PCI\VEN_10DE&DEV_01EA
%PCI\VEN_10DE&DEV_01EA&REV_C1.DeviceDesc% = NO_DRV, PCI\VEN_10DE&DEV_01EA&REV_C1
%PCI\VEN_10DE&DEV_01EB.DeviceDesc% = NO_DRV, PCI\VEN_10DE&DEV_01EB
%PCI\VEN_10DE&DEV_01EB&REV_C1.DeviceDesc% = NO_DRV, PCI\VEN_10DE&DEV_01EB&REV_C1
%PCI\VEN_10DE&DEV_01EB.DeviceDesc% = NO_DRV, PCI\VEN_10DE&DEV_01EC
%PCI\VEN_10DE&DEV_01ED.DeviceDesc% = NO_DRV, PCI\VEN_10DE&DEV_01ED
%PCI\VEN_10DE&DEV_01EE.DeviceDesc% = NO_DRV, PCI\VEN_10DE&DEV_01EE
%PCI\VEN_10DE&DEV_01EF.DeviceDesc% = NO_DRV, PCI\VEN_10DE&DEV_01EF
; Do-nothing section used to avoid "Unknown hardware" installation prompts.
[NO_DRV]
Include=machine.inf
Needs=NO_DRV
[NO_DRV.Services]
Include=machine.inf
Needs=NO_DRV.Services
[NO_DRV.HW]
Include=machine.inf
Needs=NO_DRV.HW
[Strings]
SystemClassName = "System devices"
NVIDIA = "NVIDIA"
NVIDIA_MFG = "NVIDIA"
PCI\VEN_10DE&DEV_01AA.DeviceDesc="NVIDIA nForce 220/230 Memory Controller (DDR)"
PCI\VEN_10DE&DEV_01AB.DeviceDesc="NVIDIA nForce 415/420/430 Memory Controller (DDR)"
PCI\VEN_10DE&DEV_01AC.DeviceDesc="NVIDIA nForce 220/230/415/420/430 Memory Controller"
PCI\VEN_10DE&DEV_01AD.DeviceDesc="NVIDIA nForce 220/230/415/420/430 Memory Controller"
PCI\VEN_10DE&DEV_01EA.DeviceDesc="NVIDIA nForce2 Memory Controller"
PCI\VEN_10DE&DEV_01EA&REV_C1.DeviceDesc="NVIDIA nForce2 400 Memory Controller"
PCI\VEN_10DE&DEV_01EB.DeviceDesc="NVIDIA nForce2 Memory Controller"
PCI\VEN_10DE&DEV_01EB&REV_C1.DeviceDesc="NVIDIA nForce2 Ultra 400 Memory Controller"
PCI\VEN_10DE&DEV_01EC.DeviceDesc="NVIDIA nForce2 Memory Controller"
PCI\VEN_10DE&DEV_01ED.DeviceDesc="NVIDIA nForce2 Memory Controller"
PCI\VEN_10DE&DEV_01EE.DeviceDesc="NVIDIA nForce2 Memory Controller"
PCI\VEN_10DE&DEV_01EF.DeviceDesc="NVIDIA nForce2 Memory Controller"

New K8N Neo4 Platinum build. Help, Nforce4 driver question?

I am building a new K8N Neo4 Platinum system (see my sig). I wanted to get the latest Nforce4 drivers, before installing XP. I noticed on the Nvidia website a 5.10 Unified Driver download and a 6.66 AMD download. Which should I use? It looks like the versions in the 5.10 Unified Driver are actually older than what is in the Nforce4 drivers, from the MSI site. If I use the 6.66 AMD drivers, should I make a SATA Raid Driver floppy, from them, to use during the XP install? Any advice is appreciated.

just do it from a floppy, LiveUpdate is crap
and yes you HAVE to F6 these drivers on Windows install if you plan on using SATA or you cannot boot from SATA
unfied drivers are NOT FOR NFORCE 4. You MUST use the NF4-specific 6.66 (or earlier)
Unified Drivers are specific only to nForce 1/2/3. AMD and Intel each have specific and unique driver sets for nForce4.
download 6.66, extract and explore the folder
go to IDE->Win2K->SATARAID and copy everything in this folder to a floppy
make two floppies just to be safe
you cannot use CD, you MUST use floppy because Windows will look in a: only
as soon as Windows install starts you will see a screen that says "Press F6 to install third party SCSI or RAID driver"... hit F6 and insert floppy and after a few minutes, you will get a screen that says"
"Press S to install other drivers..."
press S
next screen comes up, first select and install "nVidida Raid class driver (required)" -->hit enter
back to "Press S to install other drivers..." screen
press S again
screen wil come up again, this time choose and install ""nVidia nforce storage controller(required)"
one more time back to "press S to instal other drivers...", this time just hit ENTER
now you're good to go

Largest SATA drive for K8N Neo4 Platinum

I have a system based on the K8N Neo4 Platinum board, I'm planning to up, the storage capacity of my rig and was wondering if I can install a 500 GB or larger SATA or SATA II drive on it?
to make long story short I would like to know whats the largest Hard Drive (either IDE or SATA) one can install on a system with this board without problems or compatibility issues.
I presently have a Maxtor Diamond Plus 80GB SATA drive,
Any takers??? ???

I see no problems, just try it.
As for a Sata-II drive, don't take Maxtor, any other drive should be fine.
However, you maybe must jumper it to SATA-1, depends on the onboard controller.

New build: MSI K8N Neo4 Platinum + maxtor 300gb = problem?

Got these 2 products included in a order:
MSI K8N Neo4 Platinum nForce4 Ultra (Socket 939)
Maxtor DiamondMax Plus 10 NCQ 300GB
While checking up on the MB on the MSI site, I noticed a version of the bios (1.2) that says 'support for 300gb maxtor drives'
That's the same HD one I have coming with my order >.<
If the MB I get hasn't got that version of the bios already installed will I have trouble installing the drive?!
I downloaded the bios and it says in the readme not to install it from a floppy disk, so I guess you need a system up and running to make that update in the 1st place. No Idea how to go about this, if the need arises.

Quote from: Supershanks on 19-May-05, 21:45:00
Hi drjugears,
Welcome to the forum.
Many people are runnimg ok anyway as dope says.
But it's not an issue you can update the bios via floppy b4 connecting the maxtor.
See Flashing the BIOS for Users using NON FAT file system This is a guide written by msi. Strictly speaking if you folow the instructions you aren't flashing from a floppy the actual update is done on a virtual drive in memory.
if you need a floppy boot disc see Why no floppy for bios flash?
luck with build
Thanks very much for the welcome and info.
Unfortunately I'll have to wait a while to see...I installed everything....but need some adapter for the 6pin connecter on the ATI card. The power supply came with some 8 pin one. So I need a 4 to 6 pin adapter. Doubt If I'll find one local, so will probably have to wait until monday now to try it out.

Problem replacing K8n Neo4 Platinum

Hello everybody, this is my first post here, I am a new member from Italy.
I have this problem:
I own a K8n Neo4 Platinum and when I changed the VGA from Nvidia 6600 GT to 8600 GTS the Mobo doesn't post anymore.. The usb diagnostig bracket says it's a memory problem but when I've put my memory banks on a different PC, they work just fine.
I think the problem was caused by the little space that I had between the VGA and the chipset cooler (Zalman passive);when I installed the VGA I damaged the chipset. Taking a closer look at it I noticed that 1 edge is damaged. I also substituted the Power suplly but the result is always the same.
So I decided to replace the mobo but I don't want to reinstall windows. Finding my same mobo is impossible here in Europe. I only found the K8n Neo4-F.
My question is the following :
-Does this Mobo use the same drivers that were installed on my HD? (latest driver downloaded from Nvidia version 6.86)
-Will I have problems with Windows ?

Massi186,
Moan Guide
Richard

K8n neo platinum and hard drive problem...

greetings...
well, I have K8n neo platinum mobo with SATA1 controller, and I bought WD 250 GB sata2. I did set up jumper to limit transfer to SATA1 mode on my new drive (although I tried it without jumper, it is the same). Hard disk is working but, I have varying trasfer rate when I copy files from WD250 on other drives, and when copying on that drive. Transfer is going fine, and then it goes very very slow, then again fast, then again slow...And, sometimes, when I am copying large amount of data on that drive, my computer freezes. When I test sustained speed, it is different almost every time (goes from 14 to 65)...
I searched thru internet - with no sucess. I have very good power for my PC. I changed sata cables, and power cables. I updated all drivers. I tried installing XP IDE drivers for that new SATA2 hard disk. I tried almost everything, and with no sucess. WD250 is working fine for, let's say, a couple of hours, and then it again goes slow with varying transfer rate when copying. I also have a very good cooling system, so it's not because of overheating. I contacted WD, they told me to run their diagnostic tool, and the disk was healthy. They said that drive is ok then, and that it is probably my mobo that is causing problems.
anyone have a clue what is going on?
thanx in advance

damn...
can't believe no one ever had similar problem...

K8N Neo4 Platinum "Initializing Floppy Drive Controller" problem

Similar Messages

Maybe you are looking for