K8n neo4 platinum recognized HDD, no boot

there are two sata hard drives in this system, the main drive (which is connected sata1) houses the operating system while the drive plugged into sata2 is a large storage drive. bios recognizes both of these drives, and my boot sequence is floppy-hdd-cdrom with the hdd sequence being maindrive-storage drive. for some reason whenever i attempt to boot it goes through post fine but before it begins loading windows i get "boot from cd:" followed by "disk boot failure, insert system disk and press enter."
i have already made sure that the settings in bios are proper, any help would be appreciated seeing as msi's support request form seems to have an error in the page.
for the record:
k8n neo4 platinum
(2) 1gb pc3200 Corsair memory
Ati x1650pro
80gb sata hdd
120gb sata hdd
generic cd burner/dvdrom/floppy

If you change ur MB whitout formatin' C:// You wont be able to starwindows normally , that msg is normal and restartin too if you're using the same partition onto another MB, you've two options 1st_> backup data from "main HD" to "second HD" and format the first HD or reinstall windows on main partition, for that-> insert win xp boot CD, set up bios from booting from CD DRIVE and then when blue installation screen shows several options select "fix previous Windows xp installation" and that's... The only bad thing of that is that you might also reinstall some programs and thirt party software and you'll spend a lot of space (and performance) in "Temporaly files" from the old previous OS installation, I recommend u choose FORMAT ur main HD, Good luck

Similar Messages

K8N Neo4 Platinum SATA2 HDD Not Detected HELP!

I have built 3 identical rigs, the rigs are in my signature. the problem i am having is that the SATA2 hard drives are detected by the bios, i have them plugged in the purple slots sata1 and sata2, When the drives are plugged in there the system runs slow. What happens is when i put the windows XP cd in to install it starts to boot from the cd and gives me the part "setup is detecting hardware on the black screen" then that goes away and i just get a black screen. The same problem occurs on all 3 rigs. The only way i can manage to get everything working and with windows installed is if i use the orange sata slots which are sata5 and sata6, but then i have to use it as raid. Currently have them setup as raid0. I was wondering if anyone knows a solution for the problem. Running the drives on the orange slots doesnt use the 300MB/s only runs them at 150MB/s. The only thing i can think off is that we would need a BIOS update to correct the problem with the sata2 hard drives. Seems to me like other people here are also having problems with sata2 hard drives.
Any feedback or sugestions would be apreciated.

gffreire,
I am the person who started the tread you referenced.
The Problem must everyone is having is with true SATA II drive the have 3 Gb/s speed and NCQ features.
The fix for all of this takes two things, (1) BIOS V1.A and earlier have a problem and (2) all current nVidia RAID drivers posted, unless they have posted some thing new in the last day, that include 32-bit and 64-bit have also got problems.
I have tested a new beta BIOS and Beta driver for 32-bit when used together, they work. The new-posted BIOS V1.B appears to have the BIOS fix in it, but currently posted, RAID Drivers still have no fix incorporated in them.
Send me your E-mail address by Personal Message and I will send you a copy of the Beta 32-bit drive. So, if you upgrade to BIOS V1.B and are installing the beta driver, during clean install, it may solve your problem. However, be remaindered this driver is pre-beta and also does not includes no “xxx.cat” file. Effects on your system could be anything. I have gotten it to run using a clean install on both of my MS-7125 MBs.
Roger

Constant HDD access (K8N Neo4 Platinum)

Hello all, this is my first time posting on these forums.
A couple of days ago I put together a new system for myself, with the following components:
* Athlon64 3200+ processor
* MSI K8N Neo4 Platinum motherboard
* 1Gb RAM
* Gigabyte 128Mb GeForce 6600GT graphics card
* 2x Seagate 250Gb 7200rpm SATA drives
* LG IDE dual-layer DVD-RW drive
* Apacer 7-in-1 internal USB 2.0 card reader
* Thermaltake "soprano" ATX midi-tower w/ 400W PSU
The two hard drives I have connected to ports SATA5 and SATA6 on the motherboard and set up in a RAID1 configuration (using the on-board Silicon Image SiI 3114 RAID controller). I then installed Windows XP Professional, which went on fine. The only problem I have now is that the hard drives are being constantly accessed by the system, even when I'm doing nothing on the system. This isn't just an occasional access once every second or so, the little HDD LED just flickers away merrily the whole time. I have run both filemon and diskmon on the system, and found that while no particular files appear to be being accessed, there is almost constant write activity being performed to the hard drives.
I have narrowed it down to somehow involving the Windows XP RAID drivers. If I boot from the Windows XP install disk and load the third party drivers for the SiI 3114, I get the constant disk access when sitting at the first screen of the install process ("Welcome to Windows XP" text-only screen). If I do the same without loading the drivers (thus Windows does not recognise the RAID drive), no disk access. I have tried updating the RAID controller drivers under the Device Manager (now up to version 1.2.0.0), but it does not fix the problem. I have done a full virus and spyware scan (bearing in mind that this is a clean install), with no results. I have checked all running processes and services (including making sure Indexing Service is not running), but have been unable to find anything that could be causing this constant activity. I have yet to try actually breaking the mirror and running the drives off the normal SATA controller. I will be trying that tonight when I get home if no other solution presents itself, but obviously I would rather get it behaving properly in RAID1 if at all possible.
It's driving me crazy. There doesn't appear to be any actual issues with the performance of the machine, but the constant hard disk activity can't be good for the drives long-term. I have searched these forums for a possible solution, and while some people have had similar problems, none of the suggested solutions have worked for me so far. If anyone can help me with my dilemma, I would be Eternally Grateful(tm).

Yes! At least I'm not alone... constant disk ticking is driving me nuts too.
I have same issue with a newly built system - different board but Sil3114.
My C: is on the NF4 SATA interface, but I have 4 250GB Seagaets on the Sil3114, intended for a RAID5 array. Having installed XP, I've become distracted by the constant disk access and have been trying everything to eliminate it before proceeding with the rest of the build - nogo. Your post gave me the clue - boot with Sil3114 disabled = no disk activity; boot with enabled = constant disk flogging.
I've got the Sil driver up to 1.2.3.1 but no better. Suspect it may be the Sil3114 BIOS that needs upgrading but seems no way to flash it - have you got anywhere with your debugging?
Appreciate a solution before I go crazy with the tick, tick tick....

K8N Neo4 Platinum not booting

Hi I just moved my fully working K8N Neo4 Platinum based setup from one case to another, and now it's not booting. All fans are starting but the USB D-bracket 2 shows LED's 1 and 4 yellow and 2 and 3 red and the computer hangs. I can't seem to find this LED combination in the manual where it's only supposed to show green and red lights. Anyone got any idea of what's wrong?
Thanks

Okay I'll try to be more specific, the thing that makes me clueless is that the rig has been working flawlessly before.
CPU/Memory:
AMD Athlon64 Venice 90nm 3500+ 2.2GHz
2x512 MB OCZ DDR PC-4000 Gold VX (500 Mhz, 2-2-2-8)
I've tried unmounting every single component and mounting it back on again. I've tried both memory sticks in a single slot but no luck.
The PSU it's been running on is an Antec True380SP 380W (included in Antec Sonata case), yes 380W is a bit low so i tried a beefier PSU as well (Antec True430P 430W) with the same result.
Max Amperage:
Antec True430P 430W -- +3.3V = 28A, +5V = 36A, +12V = 20A
Antec True380SP 380W -- +3.3V = 28A, +5V = 35A, +12V = 24A
HDD:
Western Digital Raptor WD740ADFD 74Gb 10000rpm 16Mb cache SATA connected to SATA1
All fans power up, Power LED lights up and HDD powers up, but no VGA signal. I've reset CMOS and I've read through the stickies and tried the fixes there applicable to my problems, but no luck so far. Only thing I can think of that haven't tried is switching the CMOS battery.

K8N NEO4 Platinum cold boot problem with 165 opteron?

I have this board and have a cold boot problem with my opteron. Is there anything I can do to fix this? Its starting to get very anooying.
K8N NEO4 Platinum
165 opty dual core
2X1GB Ballistix PC4000
160GB sata2
7800GTX
X-Fi platinum
600 watt seasonic PSU

Well I am running them at the rated speed of 250 and the rated timings of 3-4-4-10 on the rated 2.8 volts. Ballistix have been known to die quickly when you throw to many volts at them for some reason. I dont get the cold boot problem with the OCZ. Once I finally get it to boot with the Ballistix it works just fine but the next morning I play hell to get it to boot again. I dont even get the main screen to let me get into bios. It just stays black. I have done all kinds of stress testing and ran memtest with no problems. I am really at a loss here.

Please Help K8N Neo4 Platinum won't boot?

Hello,
I could use your expertise in this matter. I have built several systems and never seen this before. My system will not boot with the hard drive
and/or DVD drive attached. It will boot with just the 1.44 floppy attached. My system is as follows:
MSI K8N Neo4 Platinum ATX AMD Motherboard
connect3D 3038 Radeon X800GTO 256MB 256-bit GDDR3 VIVO PCI Express x16 Video Card
Rosewill RV500S-2 500W Power Supply 500W ATX 2.01
+3.3v- 30A
+5V - 45a
+12V1 - 18a
+12V2 - 16a
AMD Athlon 64 3000+ 1GHz FSB Socket 939 Processor
CORSAIR ValueSelect 1GB (2 x 512MB) 184-Pin DDR SDRAM Dual Channel Kit System Memory
Cas Latency 2.5
Voltage 2.5V
Unbuffered
Windows XP professtional Service Pack 2
I tried resetting CMOS, changing the cmos battery, re-setting the video card, moving memory modules (from positions 1&2 to 3&4). The power supply is working. When I put my hard drive into another system it boots perfectly. Please help!
Thanks
Tony

All that info and I still don't know where you are plugging them in. SATA or IDE(PATA)? Both?
Can you describe the not booting a little more? i.e. No video at all, you see POST but it doesn't complete, POST completes but you can't boot an OS.

Slow Boot problem with New K8N Neo4 Platinum HELP

Hello,
I just set up my new rig, the system specs are..
amd64 3500+
K8N Neo4 Platinum PCI-E (non SLI)
2x80gb SATA (insockets 5 and 6) Silicon
2x512 ram generic
BFG 6800 Ultra OC
antec 550 truepower
The entire install went well.. It zipped through windows98... But when it tired to Boot windows98.. it went really really slow.. The animation bar at the bottom was chugging.. like lagging.. and took well over 10 minutes to fully load..
I check RAM was not it.. re-connected.. was not it.. new SATA cables.. no idea any help would do.. getting impatient and tired =O must get it up tonight!

Don't know if you or many people have seen this it's appeared over the last few days K8N Neo4 Platinum - NOTE: NVIDIA nForce 3/4 Series board DO NOT support Windows® 98/ME
There are people running 98 but my own understanding was that 98 could only use a sata drive as a data drive & could not be installed on a sata drive. Where have you installed it ???
see Win 98SE IDE problem.... Has anyone worked it out yet?
luck

K8N Neo4 Platinum ignores boot order

When I try to install windows on my K8N Neo4 Platinum on my RAID1 connected to nvraid I ran into problems when using a single SATA-drive on the same controller though I set nvraid as primary boot device and the single drive as secondary. Windows allways wants to write some information on the single drive (nvata-bus) priory to the RAID1 on nvraid-bus.
This is really embarrassing because I use the single SATA as hot swap backup.

bunfried,
Try a Bare Bones Install. Just have the HD Array you are going to install Windows on to and the Optical Drive that you will use for the WinXP CD.
Once you complete the install, then all in the additional Drives.
Take Care,
Richard

New K8N NEO4 Platinum (non SLi) wont leave boot screen???

I just went out and purchased:
AMD Athlon 3000+
K8N NEO4 Platinum
Some standard case with a 450w power suply
On the +12v it says I have 18a
And Im using some things from my old PC:
(PCI) ATI Radeon 9200se (CrapTastic!)
Maxtor 40Gig (not Sata)
1x Samsung PC2700 DDR 512mb RAM
This is my first PC build and I ran into a couple of problems:
I have tried 3 different PS/2 keyboards(2 older and 1 newer) and none of them work. It shows the Platinum screen and then goes to a different screen that says "Keyboard error or not plugged in"
So I try my USB keyboard that I got about a year ago and the lights flash on the kb when I first start up but.....once I get to the Platinum screen the keyboard becomes unresponsive and I cant move off the Platinum Screen into BIOS or anything.
PLEASE HELP!

Well I went out and purchased a USB to PS/2 adapter and plugged it in with the USB keyboard that would light up but still not work and......................... STILL DID NOT WORK!
Im going on 2 weeks now with no Counter-Strike:Source and im goin nuts
Quote from: ck5134 on 07-September-05, 03:12:50
Grimster i agree totaly with jeanguy, you need around 25-30amps min on these boards, so try a mates psu.
Do I really need more than 18a with my system? How much money (ballpark) in US dollars do you think a adequate PSU for my rig would cost???
I am really thinking of just takeing it back and getting it replaced with the same mobo and see if that works.

K8N Neo4 platinum edition v1 (bios W7125NMS V1.6 062305) -- after POST stucked

hi i'm runningan athlon 3000+ in K8N Neo4 platinum edition v1 (bios W7125NMS V1.6 062305) and i have a very like problem:
today i tried to install freebsd(install started fine, nothing went wrong, i repartioned my hdd and the installer started),
for some reason i had to abort the installation process. since then i can not boot in from any device(cd,usb the hdd is in a
half way to bsd install state so it's not an option atm).
the post screen comes up and i can interact with it in a way(i can press tab and it drops me
to the detailed post screen,ctrl-alt-del also works i can restart with it), but i neither can enter to the BIOS setup /DEL/ nor the boot menu /F11/.
i've tried reseting bios settings by flushing cmos(removed the battery,pressed SW1. something must happened because the post now checks for sata devices
and the graphical screen/that one u can bypass by pressing TAB/ was not presented before).
it also detects my hdd and my cd-rom too. but still nothing happens after the POST.
others said updating my bios would help. but still there is no option to boot from.
if i am doing wrong something please let me know,
thank you for your help
Andrew

the solution:
disable ide1/slave when the broken hdd is not connected and bios accessible; poweroff; reconnect the broken hdd to the PC;poweron; boot from a linux livecd; gpart/fdisk/something to repair the broken hdd;be happy life is nice
the trick was that bios and post is not messing with the broken hdd(while it was blocked in the bios)
so i could boot with a live cd when my hdd was connected to the PC.
since linux trixx out bios i was abel to interact with the post_killer_hdd (even it was blocked in the bios).
i hope somebody will be able to use it one day if something is not understandable drop me a PM.
problem solved im installing the os to the hdd,topic is SOLVED.
maybe the other guy who has some similar issues with his config/hdd could use this post too.
regards,
/\ndrew

K8N Neo4 Platinum Ultra nForce4 no post.

Took the cpu off and cleaned it, upgraded the video card started the computer and no post. Led's 1,3,4, green 2 red. Took cpu out and checked it no bent pins, checked all connections. Sometimes when it boots it will have 4 green led's but no video. Tried another vid card same thing. Tried booting and holding the insert, cont+home, F1, delete keys. Get power to the fans and hear the HDD sometimes.
Specs.
MSI K8N Neo4 Platinum Ultra nForce4 bios v1.6
Athlon 64 3700+ San Diego Core
Geil value ram
1-36GB Raptor
, M45 Powercolor Radeon X800 GT PCI-EX 256MB DDR3 R480 Core
XP.Pro.W/SP.2
X-Connect 500W ATX PSU
+5V +3.3V +12V -12V -5 +5VSB
30A 28A 34A .8 .3 2
Edit: Have cleared the cmos many times. If I boot holding the insert key down for a while I get 1,3,4, leds red 2 green, if I then push F1 they all turn green but still no vid.

No posts to your post either LOL
Anyway - could be fans causing it - I had my Neo not booting until I disconnected a case fan from the mobo fan header output.
Try with just leaving the cpu fan (could also be this one of course) .

SATA drives not being detected - K8N Neo4 Platinum

I have the same problem, different PSU!
msi k8n neo4 platinum pcb 1.0
3000 64 939
corsair 1gb dual channel ddr400
nvidia 8800gts
antec truepower 550 (19a @ 12v)
used to run 2 ide maxtor 120 and 80
added in a sata dvd writer, worked for 6 months
added in a sata 1TB seagate 7200, sata fails a majority of the time
same symptons now persist as in original post.
:< either bios detects both sata drives, neither, or it crashes. this happens respectively rarely, uncommon, and most common
what ive tried:
updated all mainboard, bios, video drivers to the most up to date (i had to in order for bios to detect the full size of the 1TB)
no ide, same problems
only 1 sata, with and without ide, same problems
the sata only works after a long period of time (or randomly), that i dont use it
(ive had both sata unplugged for 12 hours, booted up this morning with them and it detected, i selected safe mode boot, after making it through a majority of the load, it crashed)
testing a new psu in a day or so, much more powerful. ill give you all my results.

The cables aren't overly bent?
"...worked for 6 months"
"...fails a majority of the time"
Not very relevant, but since i found the FAQs, and there are no less than four FAQs for hard disks http://global.msi.com.tw/index.php?func=prodfaq&maincat_no=1&cat2_no=&cat3_no=&prod_no=165#menu :
"Silicon Image Si3114R Raid bios doesn't have JBOD setting in it, why?
In the new Silicon Image BIOS, JBOD already been renamed as "Concatenation".
If you want to use single SATA HDD or when tou want use each SATA HDD as IDE mode, you can choose "Concatenation" function in Silicon RAID BIOS."
"I am using a SATA hard drive with NCQ technology on this motherboard and I am experiencing problems. How do I fix it?
The issue depends on the Southbridge chipset. Nvidia is currently working on an updated nForce driver to address the issues with certain hard drives.
You could contact Nvidia support to ask for the new driver if there is one. If there is not any new driver to solve the issue, please disable NCQ on your system." /My fattening. /

Multiplier ? K8N Neo4 Platinum

Got this rig to POST the other night, installed W2KPro SP4, all seemed well. Last night I installed Prime, Sandra CPUZ etc. Parts are all still on the bench. I should mention that I'm using a $10 PCI Video card for posting, troubleshooting etc. I can only display in 16 colors. I don't know if this would make a difference. I started foolin around Ocing this thing, upped the FSB speed from 200 to 220, upped the CPU voltage up slightly, didn't fool w/any RAM timings or change anything else. The machine will boot to Windows, and CPUZ shows the overclock(220 10X). Given my CPU stepping and this mobo, I fully expected Prime to fail, which it did, promptly. I've read here that I can drop the multiplier to say 9 for example to reach a more stable OC that way. I just don't know how. I'm also unclear on Ocing the RAM, but perhaps I'll post on that later.Thanks
Present build
MSI K8N Neo4 Platinum
Athlon 64 3200+ (Winchester) CBBID
Artic Cooling Freezer 64 w/AS5
2X 512 Kingston Value KVR400X64C3
EVGA 6800GT
2X Seagate Barracuda 80G SATA HDDs
Antec 480 Neo Power
ASUS® P4PE Mainboard, (Intel®82845PE Chipset)
2.4Ghz Pentium® 4 Northwood core, @ 2.52Ghz
512Mb Samsung® 3200 400DDR RAM
ASUS® V8420 128Mb DDR GeForce® 4 Video card (NVidia Ti 4200)
Creative Labs Audigy® 5:1 Sound Card (OEM) w/ Firewire.
Happauge® PVR250 video capture card
2X Maxtor® DiamondMax® 60G HDDs, (7200 RPM 2 MB cache)
Lite-On® 16X DVD, Lite-On® 48X CDRW
330W Antec® Tru-Power PSU
Antec® PlusView 880 AMG Full Tower case, (painted, candy apple metallic blue).
Stock Intel® HSF, 5- 80mm case fans. Stealthed optical drives, subtle light mod.
PowerMac® G4 1.25GHz
Toshiba Satellite® Notebook 1.2 Ghz Celeron

set ram ratio to 166, as for the multiplier look for something called CPU ratio, also you probably need to drop the HTT down to atleast 4

K8N Neo4 Platinum Bios Update - Best Procedure?

I have built a new system:
K8N Neo4 Platinum Award Bios Version 1.3
ATHLON XP64 X2 4200+ E4 Stepping
2GB Transcend RAM (2x1GB)
EVGA 6600GT 128MB PCI-E
Samsung Spinpoint 200GB SATA on Sata1
Samsung TS-H522U DVD-RW
Floppy
Seventeam ST-550EAG 3.3V= 30A, 5.0V=30A, 12V1= 18A, 12V2= 18A
Windows XP Pro SP2
I'm not overclocking and DOT is disabled. Optimized parameters are loaded.
System is running but my BIOS version does not support dual core. I have installed all NForce 6.66 drivers and VGA drivers, and all Windows updates. What is the best procedure to flash bios, Winflash or MSI floppy method? What version of BIOS should i try, 1.6 or 1.8?
Thanks.

Quote from: hansh on 27-September-05, 16:34:38
Hi, when you ask 10 people about the best method to flash BIOS, you will probably get 10 different answers
Some observations:
1. Flashing under Windows has become "normal procedure" for boards of most other manufacturers; (I will not use this method for my MSI boards, though, because of the negative opinion on it in this forum. If the comments are correct, then the only conclusion can be that MSI software engineers are at present not able to deliver a Window-based flashing program with which MSI-BIOSes can be flashed into MSI boards in a safe way. I'd rather not find out the exact reason for this . I have used Windows-based flashing programs numerous times with boards from other manufacturers - Abit, Asus, Soltek, ECS, etc. without any problem).
2. If the procedure as described by Syar really has significant advantages over "plain flashing", then it means that either the BIOSes are flaky, or the boards are instable. Such precautions have never been necessary and should not be necessary! I can only recommend - just to be on the safe side - that, while flashing, you dance around the computer, carrying two carrots, an onion and chanting "Flash! Flash! Flash!
3. There is something to say for not flashing from a floppy. Floppies are the oldest part of nowadays computers and the medium is probably the least failsafe part ... Therefore I have reserved a small (100 MB) FAT32 partition on a HDD, BIOS files and most recent flashing program will be copied to that partition. I will start the PC with a W98SE bootflop, go to that partition and flash from there. I have used this method a great number of times over the years, I will never add any switch when running the program.
Additional Info
Regards
Hans
Hi hansh,
thanks for that. I'll boot with a Win98 bootCD (NTFS support included) and thinking about flashing with an Iomega USB pen drive (FAT32). Any comments here?
And, blazing storm, thanks again for your valuable reply.

K8N Neo4 Platinum - Lost Sound

I have a K8N Neo4 Platinum mobo and recently I have suddenly lost sound in both OS's. I am running XP64 and Fedora Core 4/64. Primarily I work in the Linux OS. I noticed that the sound was gone the other day while editing in Kino. I have had power outages recently while on. I am stumped why I am not getting any sound in either OS. The speakers "pop" on on boot up and "pop" off on shut down, but nothing in between. Tried different speakers, no luck. Everywhere I look, the onboard sound appears to be recognized and has no problems, but nothing is getting out of the speakers. Any help?
Thanks

you may have a try to uninstall the audio drivers and reinstall the audio driver here.
You may also check the software player you are using.

K8n neo4 platinum recognized HDD, no boot

Similar Messages

Maybe you are looking for