K8N Neo4 Platinum Will not boot when SP2 is installed

I installed everything on my pc. Used MSI live update to get everything up to date. I then realized that I didn't do any windows updates (was up to SP1) When I put sp2 on the pc bluescreens after the windows splash screen. I can bring up in safe , vga , and network enabled modes. I didn't install sp2 on the old bios so I don't know if it is a bios issue. Has anyone else had this problem? I need to put sp2 on eventually...... I was thinking that it might be a vga problem but I don't have another PCIX board to swap.

If you have another computer with a CD burner you can slipstream your copy of XP with SP2 (just google XP SP2 slipstream). Then you can just do a windows repair. If you can't I would suggest doing a windows repair anyways but right after you get into windows install SP2.
To me it sounds like a driver conflict. If neither works, you may have to format. Again when you do install windows then immediatly install SP2, then drivers and so forth.
Good Luck
Jeremy

Similar Messages

MSI K8N2 Neo4 Platinum will not boot - SOLVED!

Hi
I have just tried powering up my system based on an MS-7125 v1 and it will not boot.
Symptoms are :
1 long high pitched beep followed by two short ones, followed by two lower pitched tones of similar duration
D-Bracket - 1 = Red, 2 = Off, 3 & 4 = Green
No display on screen - I changed the graphics card to test that - no improvement
HELP!
PLEASE . . .

Quote from: Grayone on 24-September-07, 20:57:41
Please supply us with full info on the system including the power supply and memory.
PSU = 600W Seasonic S12
RAM = 2 x 1Gb Corsair Value Select PC3200
All working fine for a couple of years.
Incidentally, I believe that the #2 LED on the D-Bracket may not be displaying red, so the D-Bracket may be trying to display 1 & 2 = Red, 3 & 4 = Green.
I changed the graphics card because that is what the beeps seem to suggest may be wrong - I am pretty confident that it isn't.

K8N Neo2 Platinum will not boot

Hello Poeple , I was wondering if anybody could help me , I have purchased a new board and the thing lights up for about a 1/2 second then the power supply shuts down, I have taken all the components off the board including the ram and processor , and still the same problem. The power supply is a 500 watt casecom model, the processor is 3.2 , Has any body got any thoughts on what i could try next? or is it a faulty motherboard.
Thanks in advance .
Scott

look at some other posts here, maybe try searching for help. look in the troubleshooting guides
if you'd seen other posts, you'll know that with little information that you have provided, you'll just get vague answers
list your hardware details in full, maybe even create a signature, then you don't have to keep repeating them when you start a new post
and look at the label on the side of the PSU, and list the amp ratings for the 3.3v, 5v and 12v rails

210-4125 will not boot when windows 7 x64 is installed

i have posted this problem a while ago "210-4125 will not boot when windows 7 x64 is installed"
hoping that some one new might have had the same problem
HP.......................................HP MINI PC 210-4125
model ................................210-4125
Bios ...................................F08
ser no................................ [edited Serial Number by Moderator]
product no.........................A8V56EA#ABU
Ram ..................................4.0 GB
system board ID............... 338d
processor .........................Atom(TM) CPU N2800 1.86GHz
Product configuration ID..0797200000204600000300100
acording to INTEL the cpu is X64 bit, but the bios will not let a X64 boot up only a x32 bit ?
and i get a message on black screen "you are trying to load an opperating system not compatable" or some thing like that
it would seem that the bios is the problem and not the CPU ? the 08 bios update only covers x32 bit and not x64
if any one out there is running x64 bit windows 7 on the 210-400 range of netbook can you tel me
1. model no
2.CPU
3.Ram installed
4 bios No
thank you
JB

thank you George
i will bear that in mind next time
i see that you work for HP ? do you have any suggestion's for my problem ?
as i mentioned before the notebook works faultlessly when X64 windows 7 is installed via the OEM disk in the external DVD drive , but if i disconnect the DVD drive it will not boot, but gets stuck in boot loop , then if i connect the drive with any windows installation disc loaded in it , it loads perfect and works perfect even if i disconnect when loaded , but i can not keep the drive connected ?
i have tried to use a USB flash drive to install X64 windows 7 but it comes back that the present CPU is not compatible ??
when it clearly states on Intel web site that it is and it works perfect when loaded ?? even the Windows update manager confirms that it will run all X64 windows OS
i understand the the bios "InsydeH20" is a very difficult bios to work with, and that Insyde have blocked the "hidden menu" via software ? i have exhausted all the software functions to open the complete bios that i can find at the moment , i think it is locked out from out side the bios and not from inside.?
any pointers in the right direction would be very helpful ,
many thanks
John

W520 will not boot when docked; blue screen

W520 fails to boot 100% of the time when docked. Blue screen shows SYSTEM_SERVICE_EXCEPTION, STOP x0000003B for nvlddmkm.sys
nvlddmkm.sys is the NVIDIA driver, which is version 8.17.12.9620, the latest shown on the NVIDIA and Lenovo websites. BIOS is also the latest.
Systems boots fine if I remove it from the dock, but it will not boot when docked.
Windows 7 PRO SP1
2 external monitors via DVI
Any suggestions?

Boot with Option held down. After the cursor changes to an arrow, Command-. (Command Period) should open and close the optical drive. After you insert the disc, click the curved arrow to have it re-scan the discs for boot volumes. Then select the optical drive and click the straight right-pointing arrow to start.
Try it with the Apple Hardware Test disc first and run Extended Tests.

HT4623 iPhone 4s will not boot after trying to install ios7 beta 4. Stops at apple logo with progress line under it. how can I reset it or get it back up to do a restore then try the iOS 7 beta 4 install again. Issue was probably caused by disconnection

iPhone 4s will not boot after trying to install ios7 beta 4. Stops at apple logo with progress line under it. how can I reset it or get it back up to do a restore then try the iOS 7 beta 4 install again. Issue was probably caused by disconnection

Obviously since you have iOS 7 you're a developer. As a developer, you signed a NDA with Apple not to discuss the iOS on a public forum. Please log in to the Developer Forum using your credentials and ask for help there, lest you risk having your credentials terminated.
Thanks, and best of luck to you.
GDG

Need to erase hard drive and reinstall system on iMac but have misplaced original install disks. Tried to use a my copy of Snow lepord 10.6 from my Mac pro but will not boot. Can original install disks be replaced. Thanks

Need to erase hard drive and reinstall system on iMac but have misplaced original install disks. Tried to use a my copy of Snow lepord 10.6 from my Mac Pro but will not boot. Can original install disks be replaced. Thanks

Yes the original Install Discs can be replaced for a nominal fee. Call AppleCare, you will need a credit card and the serial number of the machine. You can use the AppleCare Contact Info for the phone number on your part of the planet.

Please Help K8N Neo4 Platinum won't boot?

Hello,
I could use your expertise in this matter. I have built several systems and never seen this before. My system will not boot with the hard drive
and/or DVD drive attached. It will boot with just the 1.44 floppy attached. My system is as follows:
MSI K8N Neo4 Platinum ATX AMD Motherboard
connect3D 3038 Radeon X800GTO 256MB 256-bit GDDR3 VIVO PCI Express x16 Video Card
Rosewill RV500S-2 500W Power Supply 500W ATX 2.01
+3.3v- 30A
+5V - 45a
+12V1 - 18a
+12V2 - 16a
AMD Athlon 64 3000+ 1GHz FSB Socket 939 Processor
CORSAIR ValueSelect 1GB (2 x 512MB) 184-Pin DDR SDRAM Dual Channel Kit System Memory
Cas Latency 2.5
Voltage 2.5V
Unbuffered
Windows XP professtional Service Pack 2
I tried resetting CMOS, changing the cmos battery, re-setting the video card, moving memory modules (from positions 1&2 to 3&4). The power supply is working. When I put my hard drive into another system it boots perfectly. Please help!
Thanks
Tony

All that info and I still don't know where you are plugging them in. SATA or IDE(PATA)? Both?
Can you describe the not booting a little more? i.e. No video at all, you see POST but it doesn't complete, POST completes but you can't boot an OS.

Windows 8 and Canvio Desk 3TB: System will not boot when external hdd is connected

http://h30434.www3.hp.com/t5/Desktop-Operating-Systems-e-g/HP-PAVILION-A6109N-amp-windows-8-System-w...
Hi,
just recently upgraded to Win Pro on my HP PAVILION A6109N. I also bought a toshiba canvio desk 3TB. What I notice is that if I reboot my pc with the extermnal HDD connected, my system will not boot.
I have check my BIOS boot settings and the order of the boot.
I have tried disabling USB Legacy Support in the BIOS
I have reformatted the external HDD
but still my desktop will not boot if the external HDD is connected....If I disconnect the external HDD...the system will boot up ....
I am at a loss....*** scratching my head ***

Update: The only solution for me was to format the drive as ext3 and plug it into one of my Asus RT-N66U USB ports, as most routers don’t yet recognize 3TB drives as NTFS. It’s not much help to people who don’t have a router with this capability, and it also slows transfer rates to ~12MB/s.
Given the short length of the cable, your only other options are to have the 3TB Canvio sitting right next to you so you can unplug from a front USB port before each boot, or place it towards the rear of your desk and crawl under the desk to disconnect it from your PC prior to each boot.
It's a pity because Toshiba produce great internal HDD's, but my experience when it comes to external drives is they're simply junk. I wish I had read the reviews before purchasing.

K8N NEO4 PLATINUM WONT TURN OFF WHEN SHUTDOWN

Hello,
I recently built a system for my friend and he wanted the following setup. Everything works good, but when he selects Windows to shutdown, the OS goes through regular procedures, then the screen fades to black. However, the fans keep running and the PSU is still live..... so it seems the system isnt shutting down 100%. I have seen this issue before, but dont remember how to fix it. Something to do with the registry or within the system, alas, i cannot remember. please assist.
K8N NEO4 Platinum SLI Mobo
AMD 3500+ Venice Core processor 939 chipset
Antec TruePower PSU 480W
2 x 512 Corsair PC3200 RAM
Antec case
2 x Evga 6800gt ultra video cards
2 x Hitachi 80GB Sata II drives in a Raid 0
1 x NEC DVD/R/RW drives
Windows XP Pro OS

Have you tried searching at all? What BIOS version u using? I'd recommend flashing the latest.
Quote from: gerasimatos on 15-November-05, 04:32:02
Hello,
I recently built a system for my friend and he wanted the following setup. Everything works good, but when he selects Windows to shutdown, the OS goes through regular procedures, then the screen fades to black. However, the fans keep running and the PSU is still live..... so it seems the system isnt shutting down 100%. I have seen this issue before, but dont remember how to fix it. Something to do with the registry or within the system, alas, i cannot remember. please assist.
K8N NEO4 Platinum SLI Mobo
AMD 3500+ Venice Core processor 939 chipset
Antec TruePower PSU 480W
2 x 512 Corsair PC3200 RAM
Antec case
2 x Evga 6800gt ultra video cards
2 x Hitachi 80GB Sata II drives in a Raid 0
1 x NEC DVD/R/RW drives
Windows XP Pro OS

System will not boot when Aironet 802.11a/b/g adapter installed

I have an HP 8000 Elite sff that will not boot after installing the adapter. I am running XP sp3. As soon as I remove the adapter, it boots fine.???

Which adapter ? Aironet 350 or CB21 ?
Do you have another similar adapter to put in the laptop to try ?
Is the problem new ? did it suddenly happen ?
Nicolas.
===
Please rate answers that you find useful

Computer will not boot when I install my Sound Blaster Live Ca

My computer wiil not boot when I put my sound blaster li've card in. Any body have any ideas that I could try?
Thanks
tbaker

Turn off your pc, remove the jumper near the battary for 5 seconds, then put the jumper back.
If it works go to BIOS and switch off (disable) Audio on Board or Sound on Board , (if you have it), then start your pc. Should work !!!
I hope it helps!!!

2008 mac pro will not boot with HD 5770 installed.

Does anyone have suggestions for this. When I say it will not boot, I mean it will not respond at all to the power button if the card is installed (or at least if the power cord for the card is plugged into the motherboard. This is a mac pro version 3,1 with 8 cores 2.8 xeon, 22GB ram, running 10.6.8. Boots fine with xt2600 but will not boot if the 5770 power cord is plugged in. THis is an apple specific card from B and H. Perhaps I received a bad card. I have tried with and without the xt2600 installed and have tried in slots 1 and 2. I do not have any other PCI cards installed. Iknow this is not an "officially supported card" but it seems to work for everyone else.

Sounds like the ATI 5770 issue to me.
And 5770 worked on 1000s and 1000s of Mac Pro all models, like mine a 1,1 (there is even a thread of 160+ posts)
Where did you buy the cable and card, if from Apple and it is recent, exchange.
You are saying you never got to work...

Imac has white screen and spinning wheel and will not boot up---after lion install

imac has white screen and spinning wheel and will not boot up---after lion install

Please read Gray screen appears during startup.

Will not boot up with maverick installed

MAC PRO WILL NOT BOOT UP AFTER INSTALLING MAVERICK

I know it can appear like Mavericks is causing an issue, but really what has happened is the installation has uncovered some operating system issues that previously existed. It's typically best to backup your data and perform an Erase & Reinstall before doing an Mac OS X upgrade. This ensure you get a good, clean, stable copy of the OS before moving forward.
All the same, if you're getting a gray/white screen at startup, try following the steps in this KB article
Mac OS X: Gray screen appears during startup
http://support.apple.com/kb/TS2570

K8N Neo4 Platinum Will not boot when SP2 is installed

Similar Messages

Maybe you are looking for