K8N Neo4/SLi - Keeps detecting Raid at bootup

Hello everyone,
My K8N Neo4/Sli non platinum board keeps detecting IDE raid at bootup. Am I supposed to load the raid drivers on the floppy even though I don't have it enabled in the bios? That may be a separate question but curious. At this point it's more of a 10-15 second annoyance. My machine radomly freezes in windows xp too. Not sure if it's related.
Thank you to anyone that can help or has ideas.
Setup:
3500+
7800gtx msi
samsung sata 7800 160g drive on first sata
Maxtor ide on 1st IDE
2 opticals on 2nd IDE
1 gig corsair xms platinum

Quote from: SAB on 02-August-05, 17:19:32
LOL...or sometimes when O.C.'ing the CPU...SATA devices decide to take a vacation!!!!
i don't have any SATA devices on my machine, but i still couldn't figure out why after i stoped using RAID and wanted to switch to a 2X160 GB non-RAID config, after BIOS post the screen would hang at detecting NV raid. took me 3 hours to find out that if the optimized settings were loaded, the trick would be to disable the aggresive memory timings from the cell menu. strangely enough, it worked with aggresive timings and the BIOS i had when i got the mobo (it didn't hang at detecting and configuring raid) but not with the new ones. and this was without any OC.

Similar Messages

MSI K8N NEO4 SLI - RAM Detection

Hello,
I'm wondering if my motherboard is faulty or is it my video/cpu/ram that's causing my problem.
Well here's the problem. when I was doing a virus scan using norton antivirus and surfing the web my pc just shut down and restarted. But when it restarted it won't post and gives me the RAM Detection Error on the D-Bracket and the 1 beep and 1 silence and 1 beep.
I would have to clear the cmos every time it does that. I ran memtest with no errors on the ram. I've tried only using 1 stick of ram and my older ram DDR333 stick, also tried different slots, everytime clearing the cmos. With the same result. One try I had to put the DDR333 RAM in slot 2 for it to post.
When I put the DDR333 ram in it posts for abit. But when I add my DDR400 1Gb dual memory the bios still shows the DDR333 settings. After setting the ram to 2-3-3-6 and restarts it gives me the RAM detection error.
Is this due to a bad motherboard or is it my CPU or could my Video card be causing this or RAM
I don't have another CPU or Video card to see if it is those two that's causing this..
I'd RMA'd the motherboard to get it fixed, and I'm thinking of getting the Diamond Plus but before I do I'm wondering if the problem isn't due to my CPU or Video card. Would hate to buy the D. Plus and have the same problem...
Oh, My BIOS is the 9.10 that msi sent me but shows as 9.0b1 on boot up. Guessing it's a beta bios. Yes I tried the Platinum 3.8 with the same problem.
Sorry if this seems to be confusing....
Alexander

Quote from: DARTH_TSUNAMI on 29-October-06, 04:54:12
Im going through the same problem, memory detection on dbracket, i´ve tried using diferent memory and stuff, i have a 3500+ here but im not sure it that would work, im gonna try it later.
anyway i wanted to know if u guys solved your problems and how u did it, cheers
you should start your own thread on this issue. also give us the amps on the 12V line for that PSU. a detailed description of your problem and your troubleshooting up to date would also be nice.

Confused - whats the difference between K8N Neo4 SLI Platinum and Diamond??

MSI web page says the Diamond has:
"Silicon Image's SATA RAID supports another 2 SATA II ports. Transfer rate is up to 300MB/s."
http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_detail.php?UID=638
their Platinum page doesn't list the Silicone Image raid as a feature on the Platinum.
I have K8N Neo4/SLI Platinum and it has the Silicone Image raid - I'm using it now.
Can anyone explain this?
Another question: for both boards it shows: "NV RAID (Software) - - RAID function available for ATA133 + SATA HD drives or 2 SATA HD"
How can the Raid fuction work for ATA133 drives since the cables for SATA and PATA are different? What do the mean Raid for 133?
Thanks!!!
Tony

https://forum-en.msi.com/index.php?board=36.0
d/l a raid manual and all should be clear

Does k8n neo4/sli platinum support creative 6.1 surround speakers?

I own an MSI k8n neo4/sli platinum mother board with an on-board SB live 24-bit sound chip. I have confirmed that the retail version of the sound blaster live 24-bit pci sound card will support a 6.1 speaker set up (specifically creative labs megaworks 650) with creative labs proprietary plug configuration of having front center, sub, and rear center speakers all on the same (orange) plug. The plug configuration on the back of the k8n neo4/sli platinum is color coded the same as the retail version of the sound blaster live 24-bit sound card. what I need to know is... Does the k8n neo4/sli platinum support a 6.1 surround sound speaker configuration? I can find no documentation in the literature confirming or denying this. FWIW... the creative sound card softwear that came with this motherboard will allow me to configure and test for 6.1 speakers... but I get no sound from my rear center speaker. On testing, the 5.1 speaker configuration works as it should but I am unable to test for 7.1 config as I lack a 7.1 speaker setup. I am using Version 5.12.1.356 of the creative drivers downloaded from the MSI driver support.
Thanks for your time.
Malpighi44

Update...
Last night I noticed that, in windows sounds and audio devices_advanced speaker settings, there is no 6.1 speaker configuration option. (GO to: control panel \sounds and audio devices \sounds and audio devices properties \ volume \speaker settings advanced \advanced audio properties \speakers \speaker setup pull down menu).
I don't know if this pull down menu is generated by windows XP auto detection or the MSI/Creative drivers and .inf files that are installed for the SB 24-bit chip, but it leads me to believe that this MB does _not_ support 6.1 sound.
Can anyone else confirm that this 6.1 speaker option is present or missing in windows with:
1) This MB
2) Windows XP in general
or 3) if it is available to those that have an audigy or 6.1 compatible sound card
Once again...
Thanks for your time,
Malpighi44
My system:
ANTEC SLK3000B ATX CASE
ATHLON 64 3800+ NEWCASTLE
MSI K8N NEO4 PLATINUM SLI
OCZ PREMIER DDR PC3200 2X512MB
2-MAXTOR MAXLINE III 250GB
POWERCOLOR RADEON X800XL PCI-E 256MB VIVO
ENERMAX EG495P-VE NOISETAKER 485W PS
LITEON SOHW-1673S 16X8X16 DVD+RW
LITEON SOHD-16T9S 16X DVD-ROM
1.44MB 3.5IN FLOPPY
WINDOWS XP PRO service pack 2

MSI Offers Free K8N Neo4 SLI Series

MSI K8N Neo4 SLI Series Free Upgrade
So 2x NVIDIA® GeForceT 7800 don't fit ???? or am I being cynical. Not sure about the X2 or afyer spending that lot U just desrve it

Quote from: Supershanks on 15-July-05, 13:06:58
ChakkaSol,
1) You mean u didn't write it down
It is strange because I usually write down everything...even the serial number for the amd winchester chip (cbbid0509)...oh well.
Quote from: Glenn on 15-July-05, 18:04:08
Well if you can't see the serial number, then yes. (I never write that crap down)
No, you don't have to purchase anything, it's just the upgrade, looks like there might be more modifications needed that expected, for them to go to this trouble.
NEVER send them anything other than the board, you won't get it back! I don't recommend sending the board wrapped as a present or whatever master plan you may be cooking. It should be in a motherboard box, with the antistatic bag. If you don't have another box, then the original will have to do. You can always go to a local shop and ask if they have an extra box, or make a custom one..
Hey Glenn, you dont think they would appreciate it giftwrapped?
No but thanks for the info...cant I just put it in a UPS box inside an antistatic bag? And Russ, I did keep the orginal box but for the life of me I cant find the label they talk about. So I guess does it really matter if I send it back in the original box or just a box from my local UPS/Mailboxes store?

Newly Built System. MSI K8N Neo4/SLI Plat with AMD X2 3800 Crashing in all Games

I just built this system yesterday..
MSI K8N Neo4/SLI Plat with AMD X2 3800 latest BIOS 3.7 amd MB drivers
I have a Albatron Geforece 7800 GT PCI-E 256Mgs with the latest Drivers. 78
WINXP SP2 latest stuff.
DirectX 9.0C
I have 2 512 DDR3500 Memory Sticks.
SATA 160 Hard Drive
DVD 8X NEC Burner
All 3d games lok it up. 3DMark2001 SE locks it up too.
I ran Memtest and everything passed fine.
Anyway all 2d video works fine. but any 3d video screen goes black and the system locks up solid.
Any help work be appriciated
DaaDoctor

Welcome to the forum DaaDoctor
If you creat a signature (in profile) it will save you having to type your spec's out each time or us looking for it. Use mine as a template.
What PSU are you using ? Can you list the power output ? (writen on side of psu)
Going from your specs you listed your graphics card is very hungery on power so I would suggest your psu isn't up to the job under load.
Post the spec and we will know for sure.

MSI K8N Neo4/SLI SB Live! 24 bit CA 0

Hello,
I have the MSI K8N Neo4/SLI with SB li've! 24 bit sound card on-board and I want to buy a 5. speaker system with 3 digital input 3(2 optic / coaxial).
The digital optic or the digital coax output from the sound card can make 5. output so i can receive with the 5. system
The system is a Panasonic SC-HT5 (http://www2.panasonic.com/webapp/wcs...s&displayTab=S)
Thank you.

The card cannot create 5., so if the audio you're playing isn't already an encoded 5. (AC3) stream, then the card cannot change that. If you're playing DVDs, they should work fine provided everything is set up correctly (including the DVD software, it should be set to SPDIF/Bypass).
Cat

Integrated SB Live 24 bit on K8N Neo4 SLI Plat and custom EAX

I want to be able to create some custom EAX settings but I can't seem to find any way to do that on the SB Live 24 bit that's integrated on the K8N Neo4 SLI Plat board. Is anyone able to do this or is it a limitation of the integrated SB Live 24 bit? I hope it's not the latter... Thanks.

Hello, uninstall your sound drivers and go to creative site and get the lastest drivers with creative sound console, install both this sould work.. also clean out all the old sound drivers after uninstalling with driver cleaner. I think thats how i did it. good luck henry9

Bios Settings For MSI K8N Neo4/SLI Platinum MB

Hello all... Has anyone came up with the best and most stable bios settings for the MSI K8N Neo4/SLI Platinum motherboard yet. Specifically under the CPU and Memory menus.
If anyone has seen any, please post them. or post a link.
Thanks
DaaDoctor

Well that depends on the installed CPU and memory, doesnt it? So I find that question kinda odd.
One thing though: Dont use Cool n Quiet.

K8N Neo4/SLI Model Name?

What is the Model Name for the K8N Neo4/SLI? Everest is reporting MS-7046, 7100 and 7125 and for some reason it's not listed on the following page;
http://www.msi.com.tw/html/products/mainboard/mb_htm/mb_comparison.htm
It's also not listed here for some reason,
http://www.msi.com.tw/program/support/download/dld/spt_dld_list.php?kind=1&CHIP=68&NAME=Socket%20939%20(AMD%20K8)
Nor is it listed on the U.S site,
http://www.msicomputer.com/product/p_list.asp?class=mb&cpu=1#AMD939

Quote from: OPaul on 08-August-06, 11:36:36
I found out in the following thread that the Neo4/SLI and SLI Platinum are actually different boards, and the model name for mine is 7100-030.
https://forum-en.msi.com/index.php?topic=99625.new#new
oh, totally forgot about the 7100-030. an easy way to verify it is to use the CPU-Z.
the neo4/sli was the designation that they have used for the 7100 Platinum SLi in the begining for US. i just checked the US site but i've seen that it has been removed from there and only the -f version is listed with the nf4 sli chipset.
sry again, i never thought they will change a mobo designation after a year.

MSI K8N NEO4 SLI PLATINUM Northbrigde fan faulty

Hi, i have an MSI K8N NEO4 SLI PLATINUM mobo since it was released till now the northbridge fan gone faulty. It spin slow as if something causing it from spinning. Worst of all it makes a LOUD vacuum noise 'voooooooooooommm'. Anyway to fix this or to get it replaced? I still have warrenty for it. Thanks
leon,
London, United Kingdom

Then there is a post here in the forum where some guys are talking about the replacement of that hsf and I think they did find one of some brand that I do not recall at the moment, but search here and you will find it...
Be well....

MSI K8N Neo4 SLI Platinum / HDD_LED Problem

Hello,
First off I would like to say that MSI boards rock! I've always been happy with them, in fact this is my fourth MSI board. The board is K8N Neo4 SLI Platinum.
Unfortunately, I'm having a problem with this one. The problem is minor, but it shouldn't happen, at least I don't think. The problem is that even though the hard drive activity wire is properly connected to HDD_LED, it is not working with my SATA drive. No light at all!
I read in newsgroups that there are people with this same problem (although not necessarily with this same board). I haven't found a solution to this yet. So my inquiry here is:
1. Is there anyone else with this exact board with a SATA drive that can confirm his/her HDD_LED light is also not working with a SATA drive?
2. Does MSI have a fix/solution for this?
Thank you.

Quote from: Jesteronyer6 on 23-July-05, 08:10:26
THere is a positive and negative side on those pins have you tried flipping it over?
This has got to be one of the biggest "pains in the a&&" in setting up a new mobo and connecting it to a new case...

K8N Neo4/SLI Bios Update for a Newbie

This is the first MSI motherboard that I've bought and I love it. I've been wanting to upgrade to the latest bios, but I'm not entirely sure which one to get. I have the MSI K8N Neo4/SLI board, but when I go to the downloads section to get my bios update, I don't see my motherboard listed. I only see K8N Dimamond, K8N Platnium, and K8N SLI. http://www.msi.com.tw/program/support/bios/bos/spt_bos_list.php?kind=1&CHIP=Socket%20939%20(AMD%20K8)&ID=2 Which one of these would work on my motherboard, or would none work? If none of these work, where can I find one that will work?
Also, how is this bios update applied? Is it applied in Windows or through a floppy disk? Are there any recommendations over one or the other?
Any help in the matter is greatly appreciated. Thanks!

If you fill out your specs in your sig, we can see what you have. You'll probably find your board at the US site here
Also, no need to risk disaster in a bios flash if all is well. There are many stickys on this site re: flashing. It probably needs to be trimmed up a bit .
There are three ways to flash the bios. One is somewhat risky (floppy), another safe (ramdrive), and the last can be unpredictable (LiveUpdate).
I highly recommend the ramdrive or ntfs method as described here
EDIT: another good item to have on hand before you try this is the BIOS SAVIOR
This model fits my nf4 board

HELP! K8N NEO4 SLI - SOUND PROBLEMS WITH INSPIRE 7.1

People, i bought K8N NEO4 SLI, and i'm having problems with my Creative Inspire 7.1. I have certain that everything is connected in a correct way, drivers ok, but the side surround speakers doen't make no noise. Creative media is set to 7.1 channels and the speakers too...
I'm thinking that the onboard audio is a bul....
Can someone help me with this? Who here has the same kit as me?
Thanks a lot
Edinho
(brazilian guy)

Man, i'm using those standart cables offered with the product....i thing its analog, i don't know certain...
i'm very about this onboard sound...
and the worst thing, i'vc contacted creative for explanation about it and they answer me that they could'nt help, cause it's a OEM product...no response about it, have to contact MSI..
here in brazil, it's real difficult, cause anoyone cares about it...
i have absolut certain that software and hardware configuration/instalation is ok...cause i had those speakers in other PC...
i've already head tons of audio-problem topics here, and i say: K8N N4 SLI Integrated Sound is a bul...

NOT Stable overclock on K8N Neo4 SLI Platinum 3.9 MOD + Venice 3000+

Hi, to all the people that make this forum so usefull.
I´m wondering what i´m doing wrong? ??? ??? ???
I have a Venice 3000+ E3 on a K8N Neo4 SLI Platinum and 1 Gb OCZ Rev2, TCCD.
I have overclocked the CPU to 9 x 290 Mhz (2610Mhz) HTT 3X, MEM 1:1 290Mhz 2.5-4-3-10 1T 2.75V.
Memory is ok at this setting on MEMTEST v1.65.
I have tried Every VCORE possible to the CPU and Nforce Chipset and can´t make it stable.
I can work on windows with this settings but some times the computer locks. >:(
If any of you in the forum have a suggestion or recomendation, please Let me Know.
For a list of complete hardware of my rig, look at the signature.
Thank for all.

I had this exact same problem, same RAM, same MOBO, with an X2 3800+.
For some reason it wouldnt overclock 1:1, and that RAM at wouldnt run at 2.5-x-x-x-1T timings (and i dont think it did 2T stable for too long either). So i was limited to either 2 or 3.
So right now I'm running my X2 at 2.55ghz and my OCZ Platinum 1gb TCCD @ 232(2-3-3-6-1T). Done so by using 183 divider at 255fsb. HTTmulti=3x
Does dual prime 95 for 10-12 hours (havnt tried for longer)
Oh also, for voltage, the RAM has 2.80-2.85, and NF4 gets 1.55-1.60v.

K8N Neo4/SLi - Keeps detecting Raid at bootup

Similar Messages

Maybe you are looking for