K8N SLI Platinum Won't boot...

Hello!
Yesterday i got my computer parts, i slowly assemblied it and read all the instructions.
The parts was:
MSI K8N SLI Platinum
AMD Athlon 64 3500+ 2.2GHz Socket 939 (Boxed)
Asus GeForce 7800GT 256MB GDDR3 2xDVI-I
Corsair TWINX Xpert 3200C2 DDR 1024MBC
Tagan 420W PSU(I didn't get any info from the reseller about me needing atleast 450W, but it booted so im happy)
Samsung SpinPoint P120S 250GB SATA2.
It booted and i was happy, i installed all drivers from the cds and installed a game and it ran smooth.
I looked up on nvidia.com and saw that there was a newer driver for my graphics card so i downloaded them and got asked to reboot my computer and so i did.
But it didnt get any further than the re, since it didn't boot up...
All the fans are running in the computer, the memory display started and displayed info.
The screen was dead and by pressing numlock repeatedly on my keyboard i noticed it didn't work either.
I've tried to change spot on both the SATA disc and the Graphics Card. I've tried to reset cmos by holding the button.
And now im out of ideas
Thanks in advance /Hugge

Quote from: SAB on 17-September-05, 19:44:06
If you have your D-Bracket connected, what light pattern is it displaying!? Also, recheck your physical SATA connectors, as they have a tendency to back out.
I had it at first, but when i moved my gfx-card i removed it.. Should i connect it again?
Edit: Ok now i saw what use it has, i will connect it and i'll be back in a few..

Similar Messages

K8N SLi Platinum USB keyboard boot issues

Hello, I have a K8N SLi Platinum connected via an Aten US221 USB switch (http://www.aten-usa.com/?product&cat=804&Item=US221) and a Kensington USB hub to a Logitech MX518 mouse and a Logitech multimedia pro keyboard. I use this to connect the same two input devices to two computers and toggle. Previously I used a keyboard to each, with a Dell PS/2 used on the MSI motherboard.
The problem is that the MSI motherboard fails to detect the keyboard every other boot or so. It doesn't matter if I unplug the Aten switch, the USB hub or even connect it directly to the USB root hub. The only thing that solves it to restart the MSI computer over and over until it decides to start working. And I need the keyboard since I have a bootloader (GRUB) that I select which OS to boot with. The switch and keyboard works without a hitch on an older Dell computer which is also connected in tandem.
Since I need both mouse and keyboard on a single wire I cannot use a USB-to-PS/2 connector. I've found several posts here which suggests this motherboard is buggy, if that's the case shouldn't MSI issue some sort of BIOS patch?
Sincerely, Martin "xarragon" Persson

Might work.
I don't like the inconsistency you describe: working sometimes and after a lot of reboots. Would you say your system parts, please. Troubleshooting this in your end must include finding a situation where it never works, and when it always work. For example, if you don't have the mouse connected at all, if you don't use the hub, etc.
Not saying motherboards can't be damaged, specially port end, but the hub thing is a more likely culprit.

K9N2 Sli Platinum - won't boot? Can't figure out problem.

Hey guys. My computer practically crapped itself the other day, and there were so many symptoms I'm not quite sure
what to even search for.
I've had this computer for about a year now. no problems since the day i built it.
specs:
Msi K9n2 Sli Platinum mobo
AMD Athlon 64x2 3.2 Ghz
2x BFG Nvidia Geforce 9800 GTX+
2x Cosair xms2 2gb ddr2
1000 watt BFG EX Series
Sony DvD drive
1tb western digital drive
So i was playing SC2 and my computer froze. So i restarted and it hung during windows loading.
I turned it off waited a few seconds and started... still hung. Cycled it and tried a couple more times.
Still nothing. Naturally i assumed it was a virus so i repaired my windows installation. After it finished it hung on
Windows has finished repairing your computer will now restart. I waited about an hour and decided to just restart
myself. Next time it booted asked me if i wanted to boot from cd and then it just shutdown like i pulled the plug.
Then i thought well i ruined my windows install. I tried booting again it did the same thing. So i just said screw it
ill reformat. But this time there was no signal from my graphics card. When i turn the computer on it will normally
be loud and then get quiet after everything has booted. But now it just turns on and stays loud because i suspect
it's still booting. So i took everything apart. Tried connecting and unconnecting everything. moving ram etc...
Ive got it to boot twice but after that it crashes before windows loads like a plug pull and it wont boot again.
I cant tell whats wrong it could be everything but nothing makes sense. I've built about 7 or 8 computers.
gotten rid of several viruses and bad hardware but I've never seen anything like this.
I tried checking the LED codes for the board. Leds 11 and 10 and 9 and 8 alternate red and green which means HDD and floppy drive are trying to boot.
but it does that even when my harddrive is not connected and it still wont show video. Ive even rotated the graphics cards and tried a 7900gs. nothing.
Edit: now led 6 and 7 are red.
please help me out. Thanks.

Yeah the case i have is the antec 1200. Never had a problem with heat before.
Ive tried it with just the ram and the cpu and it still gives me the lights so i
guess it must be the mobo or processor. I don't have another motherboard to test everything else on
all my other pcs are 5 to 7 years old.
I was thinking about keeping all my old parts and buying these as replacements:
MSI NF980-G65 AM3 NVIDIA nForce 980a SLI HDMI ATX AMD Motherboard
AMD Phenom II X4 965 Black Edition Deneb 3.4GHz 4 x 512KB L2 Cache 6MB L3 Cache Socket AM3 140W Quad-Core Processor
G.SKILL Ripjaws Series 4GB (2 x 2GB) 240-Pin DDR3 SDRAM DDR3 1600 (PC3 12800) Desktop Memory Model F3-12800CL9D-4GBRL

Please Help K8N Neo4 Platinum won't boot?

Hello,
I could use your expertise in this matter. I have built several systems and never seen this before. My system will not boot with the hard drive
and/or DVD drive attached. It will boot with just the 1.44 floppy attached. My system is as follows:
MSI K8N Neo4 Platinum ATX AMD Motherboard
connect3D 3038 Radeon X800GTO 256MB 256-bit GDDR3 VIVO PCI Express x16 Video Card
Rosewill RV500S-2 500W Power Supply 500W ATX 2.01
+3.3v- 30A
+5V - 45a
+12V1 - 18a
+12V2 - 16a
AMD Athlon 64 3000+ 1GHz FSB Socket 939 Processor
CORSAIR ValueSelect 1GB (2 x 512MB) 184-Pin DDR SDRAM Dual Channel Kit System Memory
Cas Latency 2.5
Voltage 2.5V
Unbuffered
Windows XP professtional Service Pack 2
I tried resetting CMOS, changing the cmos battery, re-setting the video card, moving memory modules (from positions 1&2 to 3&4). The power supply is working. When I put my hard drive into another system it boots perfectly. Please help!
Thanks
Tony

All that info and I still don't know where you are plugging them in. SATA or IDE(PATA)? Both?
Can you describe the not booting a little more? i.e. No video at all, you see POST but it doesn't complete, POST completes but you can't boot an OS.

(SOLVED) K8N SLI Platinum won't post with Saphire 5750

Hi everyone. Hope you all had a nice Xmas.
This is my first post on the forums. I’m from Portugal ,so I might write things that won’t make much sense to you but I´ll try to keep it simple.
I bought a Sapphire 5750 vapor-X for my kid's PC and I’m afraid I’m yet another one with the “black screen, no post” syndrome. I have tried the card on another system and it works fine.
What I did:
Remove old card (6800GT)
Put new card in
Reset CMOS
Switch PC on… no image on screen.
The fan on the graphics card starts spinning, the blue lights are ON, but no dice. My HDD LED stays on, my CD+DVD drives LEDs keep flashing but system won’t post, not even show MSI logo.
If I remove new card and get my old one back in the PC, it will post first time.
I have spent Xmas reading forums and haven’t found anything but a lot of ppl with the same problem and no real solution for it.
Hope you guys can help .

MSI forum:
Quote
Yup,I think I have the same issue with you,man.But I have solved it as I flash the latest beta bios V192.Contact MSI Online OCSS to get the BIOS to solve your issue...
https://forum-en.msi.com/index.php?topic=131546.0
1 thread hinting a board cant support Gen2 cards:
Quote
Comments:
Nov 18, 2009- BTW, I do not even get to BIOS screen at all. All is black as if no card is plugged in.
Nov 19, 2009- After a few hours of search the result is:
Some ASRock boards do not support GEN2 video cards (such as Radeon HD 5770).
Only solution found: New motherboard.
http://www.fixya.com/support/t3235972-asrock_wolfdale1333_d667_radeon_5770
AMD forum
Quote
If i remember right 1.0 is x8 and 1.1 is x16 and i far as i know it will never work as this issue go's back 2 years when the 8800GT hit the market and it would not work on PCI Express 1.0 but it would on 1.1
http://forums.amd.com/game/messageview.cfm?catid=260&threadid=124445&enterthread=y
driver heaven:
Quote
Warning about the HD5770 well at least on my computer the XFX HD5770 + a PCIe 1.0 slot = doesn't work. Again this was on my computer. I have another computer that it ran on fine using a PCIe 2.0 slot (Asrock 780g board), but my MSI K9A Platinum would not power that card. So you may need to replace your motherboard if it uses a PCIe 1.0 slot.
http://www.driverheaven.net/ati-graphic-cards/191317-5770-performance-increase.html#ixzz2jP3dOQ9e
allover ppl are having problems with 5xxx series on older systems.
i know some comments, solutions and explanations are closer to witchcraft than anything else but where there is smoke.....

P6N SLI Platinum won't boot from XP CD after setting up striping RAID in BIOS

Hi,
I have tried fixing the boot order to CD, then RAID and vice-versa, no luck. My goal is to boot from the XP CD and press F6 to load the Windows RAID drivers from a floppy. Here is what I see:
It goes past the splash screen, detects the healthy array, tells me that the Sil bios is disabled, goes to the splash screen again, then goes to a flashing cursor on a black background. From there a Ctrl-Alt-Delete does nothing. I have to hit the restart button.
There are two Seagate 320GB drives on SATA1 and SATA2 (Index 0 and 1) in the RAID config.
Thanks in advance!

Quote from: WorkAtHomeParadise.com on 22-July-07, 05:31:27
Fixed it!
I had not enabled the SATA3 port (CD/DVD drive) for RAID in the BIOS. While it is not part of the RAID, it apparently needs to be enabled in order to function in a RAID configuration.
Booooyah!
Congratz.
Easier when people fix their own problems.

K8N SLI Platinum - lockup at boot, caused by USB hub?

Hi.
Updated my bios today as well as enabled 'Cool 'n Quiet'. This caused lockups in Win XP, forcing me to hit the reset button.
After the second reboot the computer refused to boot. According to the D-bracket it stopped at 'BIOS Sign On'.
I followed the troubleshooting guide and ended up here: https://forum-en.msi.com/index.php?topic=75712.msg533104#msg533104
Although the steps taken in the thread above didn't help, one poster mentioned that removing all USB devices could help.
My keyboard is connected to a USB hub in my monitor, when I removed this the comp started up fine, as well as when connecting the keyboard directly to the computer.
Just wanted to pass on my experiences, maybe can help somebody down the line.
Best regards
/Richard

hi nullmind,
have been 1 or 2 pps had problems with usb hubs, Glad u got sorted will add a link to this thread.
cheers.

K8n SLI Platinum can't get OS to boot

Linked over from https://forum-en.msi.com/index.php?topic=97317.0
Greetings - This is linked from the above thread and I was advised to come here to see if anyone could sheed some light on this...
System is:-
AMD64 3500+
1gb of Corsair Low latency 2-2-2-5
2 barracuda 300gb hard drives
K8N SLI Platinum mo-bo (now sadly running in single card mode...)
PSU - Hiper HPU-4S525
NX6600GT TD128E (Newer version)
Forceware - Nvidia Version: 84.21.
Problem is - I have two versions of the 6600GT and the older one will work without a problem - either in SLI or in single card mode but the newer one causes the machine to hang at OS boot - I have tried booting with the card in slot two (running in SLI mode) with the card in slot 1 (running in non-sli mode) and with the newer card in slot 1 (running in SLI) but still the same result - Is it the card, my PCU or a mo-bo problem?!?!
Any advice/help Greatly appreciated!

What motherboard BIOS version are you running? The original?
A newer version might help: http://www.msi.com.tw/program/support/bios/bos/spt_bos_detail.php?UID=641&kind=1

[Resolved] No boot with K8N sli Platinum & AMD 64 X2 3800+

Hye,
I've received these new stuff last night (everything is good until here) :
- Antec Sonata II 450W
- MB MSI K8N SLI Platinum
- Proc. AMD 64 X2 3800+
- GC Sapphire X800 XL 256Mo
I've assembled all and turned it on... No bip... but all the fans are turning... and the screen says "No signal" and becomes black ( and me )
Can someone help me? Please?
On the MSI site, I also found this :
http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_cpu_support_detail.php?UID=641&kind=1
Maybe the proc. and the Motherboard are not compatible? Has someone already tried this combinaison (MB+Proc.)?
My Thanks in advance.

Quote from: darinn on 12-November-05, 03:22:08
I will ask the sellers if they can update the Mobo for me.
But with the last version of the bios, will the mobo accept the dual-core with this proc. AMD 64 X2 3800+?
And if it's not possible I'll change the mobo.
Thanks .................................. again.
Pretty much any SLI motherboard supports the X2 3800. MSI is just really pathetic sometimes. So, I had the Abit AN8 SLI before and their latest BIOS (17) supports all X2 CPUs. But Im sure most other brands support them too.

Can K8N sli Platinum be upgraded for PCIE 2.1?

Hi. Quick question as per the subject. Can the K8N sli Platinum motherboard BIOS be updated to recognise a PCIE 2.1 MSI R5570 graphics card.
We did one BIOS update using the Live Update online thing but when we try and check to see if another newer update is now due the PC shuts down and says that we have got to undo an overclocking thing!!! The BIOS update was dated something like July 08 and I don't know if PCIE 2.1 was around then.
I now assuming that there isn't a BIOS update for this motherboard to allow PCIE 2.1. Bit worried that the BIOS update that we did has done something bad although everything other than checking for the updates again seems to be working? Just putting Windows 7 on and that seems to be going fine.
Do I send the graphics card back, or can I upgrade the motherboard and still use all or a lot of the rest of the existing items like the CPU and the memory, or will a new motherboard which accepts PCIE 2.1 pretty much force an upgrade to the whole lot? CPU = AMD Athlon 64 3500+ and memory = Corsair (TWINX1024-3200XLPT) 1024MB (2x512M Matched Pair). Things like wireless and disk drive etc shouldn't need changing would they?
Thanks

Quote from: Svet on 04-December-10, 21:26:07
No, the board is too old
Based on posts on this forum, i bought Radeon HD 4770, so not to get 5xxx series, i was eager to get. But nevertheless MSI K8N Diamond won't boot with 4770. Error code says it halts on "Testing VGA Bios".
And when searching for possible fixes i came upon AMD forum where people were complaining about the 5xxx series not working with nForce 4 chipset, but most of them got an easy fix - email the support of the mainboard company and recieve new BIOS - so all the Gigabyte users got their machines running by just sending 1 email and waiting for few hours.
I do hope MSI will respond and be as generous as the rivals, otherwise it will look bad for future buyers.

Can't open BIOs Set-up, K8N SLI Platinum, after re-flash

I used the USB Bio flash tool from the forum to re-flash the BIOs on my K8N SLI Platinum board to the latest BIOS from the MSI site, specs below.
After the re-flash, which seemed to go okay, I cleared the CMOS (turned off and unplugged computer, pushed the clear cmos button for about a minute), and re-booted.
I get a checksum error, no floppy found. I don't have a floppy drive in any case. But then I am unable to enter the bios. Pushing delete at boot gets me a screen that's blank, save for a cursor in the upper left corner. I can't enter anything from there, ESC key doesn't do anything. So I have to reboot.
I can get to the POST screen and pressing F1 allows the system to start and get to Windows, which seems to run okay. System shows that the new BIOS is installed. I just can't get into it to re-set to default settings.
If I turn off the computer, I get the checksum error again and in Windows clock and date have to be reset. But if I just reboot I just have to go through the no floppy found, then push f1 to get back to windows which has retained settings.
I tried doing the flash procedure again and got same result. I haven't tried flashing back to the old BIOs yet. MSI's site only lists the most recent BIOs, my preference would be to try a different one, but not as old as the 2005 version that was on there.
Hopefully someone can tell me something obvious that I'm missing here.
Rick
Windows XP Professionnel
Version   5.1.2600 Service Pack 3 Nu 2600
Motherboard K8N SLI Platinum, with Nvidia nForce 4 SLI chipset
Model   MS-7100
Typ   X86-based PC
AMD 64 3500+ ~2211 Mhz
BIOS/Date   Phoenix Technologies, LTD V 3.12, 10/27/2008
Version SMBIOS   2.3
4,096.00 Mo RAM

Quote
I'd also like the RAM to run at at least 333, rather than the 200 something it runs at with this BIOS.
Check this with CPU-Z at "memory tab" ==> http://www.cpuid.com/cpuz.php
BIOS post screen info can be incorrect., or current older BIOS by 200MHz it may means 400DDR In all cases its cosmetics,
the way of showing real of effective freq. can be changed in future version.
Also with four sticks it should be shown as either 333 or 166, not 200 or 400
Best check with CPU-Z how they are running
Quote
It may now be possible to put something faster in there, but I don't know that for sure. But the 4000+ should improve performance a bit.
Such old CPU's can't be found easy in present days, also its not good investing to invest in old stuffs.
You want W7 and such, changing to the best CPU wont improve much the performance in overall..
Soon or later you have to change it, then this and eventually "newest" CPU which you gonna get will became useless.

MSI K8N SLI Platinum vs 1.5TB Western Digital

Hi Everyone,
I have recently been having some issues with my K8N SLI platinum and hoping I could get some help on resolving the issue.
For the past 2 years i have been running the machine with multiple SATA drives (160GB{boot} and 300GB) and have now tried to add an additional 1.5TB WD and have encountered some problems. If i put my 1.5TB into a USB enclosure and then connect it to my machine it is recognized perfectly and I am able to write and read from the drive, However if i put it into my machine as a secondary HDD my computer fails to boot.
First when i put the drive in my computer no longer boots to windows. It gets to post and loads the drives (including the new drive) and then wont go any further. PC seems to stall and wont allow me to get to the BIOS.
I boot up the machine without the drive connected and go into the BIOS and then reconnect the drive. If i do a HDD Scan on SATA3 then the drive will be recognized (however capacity is only 136GB).
My first thoughts were that it was a bios related issue so I have updated the Bios to the latest (3.C according to LiveUpdate) and am still having the same issue. Im not really sure where to go from now.
Any help would be greatly appreciated.
Thanks for your time.
Tim

Hello! Please say what your system looks like. Include what PSU you are using.
Try a different cable.
Jumper the disk to SATA 1.
Try the disk in a different system.

K8N-SLI Platinum strange behaviour

Hi there
Apart from the northbridge making a weird noise sometimes when the motherboard is on it's side (i.e. tower case standing upright), the motherboard started behaving strangely on saturday
first the computer refused to find my network, always assigning a local ip, so i tried rebooting the router a few times, and then checked my other computer which is connected to the router fine
then i tried to play a game and noticed the sound had gone, and then the game kept quitting barely after i started it so i gave that up
then, after i had to move the mouse between this one and another computer, the usb ports (all of them, no matter whether through pci card or on motherboard, the mouse stopped working
throughout all of this i rebooted many times.
i finally gave up in the evening, and the next morning on a whim i turned the computer on and everything was fine, what's going on?!?! is this linked to the northbridge at all? i've monitored all the fans and temps and all are normal and running constantly ( cpu never above 40c)
is the motherboard losing it, or maybe the power supply (all voltages seem normal too...)
my spec
Amd 64 3000+ venice
MSI K8N-SLI Platinum
2x512mb Geil Ram
1xSata 250gig western digital hard disk drive
1x Xfx 6600GT 256mb
480w Tagen power supply (can't remember which off had, not the 2force one, the other cheap one, it's modular tho)
i was going to take the motherboard back, but now it's working fine i'm sure they wont accept it
please help
thank you in advance
Reaps

Possible suggestions are as follows: Although the manual states that your power supply should be 450w or above i think that with your PSU your fairly border line. Remember that your psu will only draw the power that it requires and as soon as you start putting 256 Mb graphics cards and upgrading to more ram it is using even more resources and can cause your system to have all sorts of dramas and Re-boots.With your network connection problems this could be due to either network problems in your area which BT or your telephone provider can help you with or as i have recently found out.. too many net work connections that may conflict with each other.Go to your controll panel,Network and internet connections then network connections you should have your broadband or dial up connection listed. If you have more than one connection listed and for instance you dont use LAN (local area connection) Networking then you will have to uninstall this connection and disable all Lan options from the Bios i.e nVidia Mac LAN, nVidia Mac LAN ROM, Marvell Gigabit LAN, Marvell Gibyte rom.A possible other prob may be to disable your IEEE 1394 connection from the bios as i had similar problems to yours but am now okay. I am not saying any of these are related directly to your problems however they are possibilities which you may like to try. Please note also that your USB problems can be solved by using the latest Bios update (which i personally have never had any problems with) but may be risky if you have no idea how to flash your bios. My advice on this would be to read the moderators (Bas..i think) instructions as to how to do this or as he suggests unistall all your motherboards usb drivers that were installed from the disk provided by your Motherboard Manafacturer, Re-boot and let windows re-install its own USB drivers which certainly worked for me.
Q-TEC 650W PSU
AMD Athlon 64 3200+ CPU
MSI K8N SLI Platinum N-Force4 MOB
2x 512Mb Hynix DDR 400 RAM Modules(Single)
Gainforce GeForce 7800 GT
Samsung 120 GB SATA

MSI k8N SLI Platinum - dead??

Hello,
I have started the PC as per usual. Pushed the power button... nothing. Then again... nothing. Then I swithed off from the switch near the mains entry. and switched on... PC started however I get nothing on the screen. No beeps.
I have an Antec Truecontrol 2.0 power supply, an MSI K8N SLI Platinum (socket 939) with AMD Athlon, 2 GB Corsair TWINX Ram, three HDDS SATA, Raptor 75GB as Primary (C:) and another two WDS. Video Card: BFG 7800GTX+ 256MB OC, PCI - Express.
System has functioned Ok for three and a half years at least. I have replaced the Northbridge Fan from the beginning with a Blue heatsink - I believe Zalman. No temp issues. No overclocking, I am not using any commander modes etc etc.
When I look at the D-Bracket I get Memory Init Error (RED-GReen-Red-Red). I am pretty sure it is not the RAM. I pulled the RAM, used only one stick... same error.
I pulled the video card out. Then interestingly the system reaches the phase just before booting and the D_Bracket shows Floppy Init error (Green-Red-Green-Green). I tried moving the video card to the second PCI -ex - I also reach the Floppy Error point. I put in a crappy PIC-Ex video card - I reach the same Floppy init point - the floppy actually seeks but does not try to read. Unfort I forgot where I put the Monitor adapter thingy so I can;t check if I get anything on the screen with the crappy PCI-Ex video card. Will get it... soon...
I have a hard time determining whether it is the Video card or the mainboard. I have pulled the battery out, left overnight, pushed the BIOS reset... nothing helped. With Video Card in PCI-Ex slot 1, I get the memory init error. With the card in PCI-Ex slot 2 or with no card or with crappy PCI-Ex, I get to the Floppy Init point.
Could it be that at that point I would be getting a VGA error that I cannot see on the screen ? Why then NO BEEPS? Does this Mobo model not beep, just uses the D-Bracket?
It is important - if it is the mobo I am done for, I have to buy Mobo, RAM, CPU... $1,000. If it is the Video card I may find something 1 slot wide and similar to the BFG ...
Can anyone help narrow this please ?
BTW on the screen I get NOTHING, if I pull out the cable the monitor says - check connection, if I plug it in the monitor goes to power saving.
Thank you Heaps

Quote from: Bas on 19-January-09, 00:17:28
Put a stick of memory in there of el-cheapo brand.
Those Corsairs you have need more voltage to start if I'm not mistaken.
Found out what the prob was - the BFG 7800GTX was DEAD. RMA-ed the card. the MSI Mobo is Ok

MSI K8N SLI PLATINUM NOT OVERCLOCK FRIENDLY AS PROMISED

This mobo is good but its false advertisment to call it overclock friendly.
People are having problems getting ther FSB over 220 and this is a overclocking mobo.
MSI K8N SLI PLATINUM (really disappointed over the mobo)
POINT OF VIEW GEFORCE 6800ULTRA @450/1300 (Really good)
Crusial ballistiX PC4000 (Great memory)
Aspire 520watt 35amp (strong as hell)

Quote from: ALFA on 25-April-05, 10:09:30
This mobo is good but its false advertisment to call it overclock friendly.
People are having problems getting ther FSB over 220 and this is a overclocking mobo.
MSI K8N SLI PLATINUM (really disappointed over the mobo)
POINT OF VIEW GEFORCE 6800ULTRA @450/1300 (Really good)
Crusial ballistiX PC4000 (Great memory)
Aspire 520watt 35amp (strong as hell)
Dear Friend don't get angry too quickly. I also have a socket 939 Athlon 3000+ Winchester. In start MSI K8N SLI Platinum was not allowing me to OC more than 220FSB in BIOS. Although in Windows I can OC it to 2.16 GHZ with NVidia NTune. It's 240FSB. You are facing the same problem that I was facing. Its 219MHZ Bug for Winchester CPUs.
All you need to do is when you are OC'ing more than 219 MHZ, just set you HT multiplier to 1x and you can go upto 260MHZ FSB via BIOS. When you get to the desktop of windows use any software to set the multiplier back to 4x or 5x (depends on how much you OC). Nvidia Ntune is a good software for this purpose. Plz keep in mind that Winchester cores are not too much overclocking friendly CPUs. They won't go beyond 2.4 GHZ and instability is bound to happen after 2.3 GHZ.

K8N SLI Platinum Won't boot...

Similar Messages

Maybe you are looking for