K8NSLI Platinum not running in SLI mode

I have two matched INNO3D GeForce 6600 GT cards (SLI) * when introducing the second card I get the message from NVIDA Use compatable SLI cards. All drivers etc up to date. Any ideas?

Quote from: snip3r on 18-February-05, 16:37:40
I have the MSI SLI Platinum board + 2x MSI 66gt, I used the 66.93 drivers downloaded from nvidia and it was running fine but will have the same problem as yours when I use ANY drivers post 66.93.
I have read some forums and they suggested that you run the SETUP twice such that the drivers are installed for both the cards. I tried this method doesn't work for me on later drivers, I'm stuck with 66.93.
Mobo was flashed to even the beta 3 bios but still the same.
sigh~
Can you be sure that running setup TWICE installled it ONCE for each card?
If you install one card first, and then run Nvidia setup, that will store a copy of the driver on the hard drive. When you then install the second card, the OS should detect it and install the drivers previously used.
Are two cards actually appearing in Device Manager?

Similar Messages

I have a mac osx version 10.6.8 no windows and i am trying to install a program but keep getting can not run in dos mode ( the disk says on back works on intel mac with parallels or vm fusion) is this program not compatible with my mac?

i have a mac osx version 10.6.8 no windows installed and i am trying to install a program but keep getting can not run in dos mode ( the disk says on back works on intel mac with parallels or vm fusion) is this program not compatible with my mac?

You run Windows in Parallels or Fusion. Then in Windows you install the program.

Help I itunes will not recognize my iphone or ipod. Trouble with USB driver, device not running in safe mode, and HDCP not supported.

Help! When I connect my iphone or ipod touch to my computer, windows recognizes my device but itunes will not. I can still see my songs, videos, and access the itunes store but my phone and itunes store have no connection so it does me no good. I have for 2 days now tried every trouble shooting method posted with no luck. I think I may have finally found a lead. My Apple Mobile Device USB Driver is showing up under portable mobile devices while it is supposed to be showing up under universal serial Bus controllers from my understanding? Also, while running my diagnostic report under itunes it also says itunes is not running in safe mode, it is not showing enabled in windows firewall (which it is checked), and the HDCP is not supported. I don't know what to do? I am in tears here, someone please help!!!

See Here for Device not recognised:
http://support.apple.com/kb/TS1538
Here for General Support:
http://www.apple.com/support/
This may also be helpful:
AMDS for Windows
http://support.apple.com/kb/TS1567

Installed iTunes 11.0.4.4 64-bit but window 8 pro 64-bit in task manager reports that iTunes is 32-bit. Why? Not running in compatibility mode. Uninstalled and reinstalled. Same result.

Installed iTunes 11.0.4.4 64-bit version. Now windows 8 pro 64-bit reports iTunes as 32-bit in task manager. Why? Both my computer and operating system are 64-bit. ITunes is not running in compatibility mode. All my music files are MP3. I uninstalled iTunes and downloaded iTunes64setup.exe from apple and still having the same result. This was a clean install by-the-way.

Hello irie00,
Thanks for using Apple Support Communities.
For more information on this, take a look at:
iTunes for Windows Vista or Windows 7: Troubleshooting unexpected quits, freezes, or launch issues
http://support.apple.com/kb/ts1717
Best of luck,
Mario

When my Itunes diagnostic's finishes running it says Itunes not running in safe mode. What is that and how do I enable it?

My Itunes diagnostic's say's that my Itunes is not running in safe mode. What is this and how do I enable it? I have the latest version of Itunes.

you cannot update this software because you have not owned the major version of this software
Shouldn't give away the secret of how easy it is.....

Unable to burn cds. Have run diognostics. i tunes not running in safe mode. invalid lower filters registry value. Failed while scanning for CD/DVD drives, error 2500. Please help.

Unable to burn CDs using i tunes. Have run diognostics.    Summary:-   i tunes not running in safe mode.
                                                                                                                                    Invalid lower filters registry value.
                                                                                                                                    Failed while scanning for CD/DVD drives, error 2500
Please help.

That's why you want to make a backup of the registry. If you didn't make a backup, use MS system restore to go back. The only values you should remove are UpperFilter or LowerFilter - one or both may be in there and can be removed. If neither value exists, then that is probably why you can't burn and Windows is not recognizing your drive as a writable drive.
... an HP employee expressing his own opinion.
Please post rather than send me a Message. It's good for the community and I might not be able to get back quickly. - Thank you.

Xk02 is not running inthe N mode

Hi,
I recorded a Bdc of XK02 but it is working fine in call transaction mode 'A' but not in MOde 'N'. Please help me out....
Regards,
Kranthi.

Hi,
Many SAP transactions behave differently in online mode and in Batch mode and this mode is determined by the SY-BINPT variable that can be controlled using the OPTIONS command in addition to the CALL TRANSACTION.
 For example, the error message that usually comes in status bar while you are running the transaction online might appear in a popup window when you are running that in batch. This will make your fields disabled for input. This OPTIONS addition will remove this problem
The way to use the OPTIONS addition.
Declare a work area of type CTU_PARAMS.
Fill the fields of CTU_PARAMS. The field NOBINPT should be set to X.
This will set the SY-BINPT to space. So now the transaction which you will be calling will run in online mode.
Example.
clear X_OPTIONS.
X_OPTIONS-DISMODE = 'E'.
X_OPTIONS-UPDMODE = 'S'.
X_OPTIONS-CATTMODE = ' '.
X_OPTIONS-DEFSIZE = ' '.
X_OPTIONS-RACOMMIT = ' '.
X_OPTIONS-NOBINPT = 'X'.
X_OPTIONS-NOBIEND = ' '.
call transaction 'BP' using T_BDCDATA[] options from X_OPTIONS.
Note:
Do not use the MODE & UPDATE additions when you are using OPTIONS. The mode & update values are passed in the CTU_PARAMS structure.
Regards
Kiran Sure

"G4MX420D-T" NOT RUNNING in AGP mode

I've got a gigabyte motherbourd that supports 2x AGP but the stupid card is running in PCI mode. How do you fix that. My graphics are now running slower than before I had a 3D card.

You should use a motherboard that support AGP 4x. :]

FlashBuilder 4.7 will not run in Debug mode with BlackBerry 10 simulator

We have developed an app that has been released both for Apple and Android working well.
When trying to do the same for BlackBerry it was rejected because it did not start at all.
The App that runs fine on the BlackBerry simulator in the "run configurations mode".
However when I try to run it in Debug mode it will not start at all. Just flashes and simulator goes back to main menu.
The debugger will after a while time out since it cannot connect to the app running on the simulator.
BlackBerry 10 Simulator runs under vmWare Fusion.
Anyone seen this before?

Hi, Silence04. Welcome to the Discussions.
You had serious disk directory corruption. That can also cause corruption in OS files: while Disk Utility or DiskWarrior may fix the directory, if the directory corruption resulted in OS files being damaged — as it appears to be in this case — then you can't avoid an Archive and Install. For important tips on this, see my "General advice on performing an Archive and Install" FAQ. Perform the steps therein in the specified order.
Good luck!
Dr. Smoke
Author: Troubleshooting Mac® OS X
Note: The information provided in the link(s) above is freely available. However, because I own The X Lab™, a commercial Web site to which some of these links point, the Apple Discussions Terms of Use require I include the following disclosure statement with this post:
I may receive some form of compensation, financial or otherwise, from my recommendation or link.

Not running in background mode 'N'

hi experts,,,,,
i have a small issues in my BDC
where i face problem when running in background
if i update in 'A' mode its get updated
whereas in background 'N' mode it doesnt take the changes
and CHANGES NOT GETTING REFLECTED/...
can you pls help me out
thanks in advance
Rachel
piece of my code as follows...
============================
LOOP AT it_final INTO wa_final.
    PERFORM bdc_dynpro      USING 'X' 'SAPMIEQ0' '1000'.
    PERFORM bdc_field       USING 'BDC_CURSOR'   'RISA0-SERNR'.
    PERFORM bdc_field       USING 'BDC_OKCODE'   '/00'.
    PERFORM bdc_field       USING 'RISA0-MATNR'   wa_final-matnr.
    PERFORM bdc_field       USING 'RISA0-SERNR'   wa_final-sernr_in.
    PERFORM bdc_dynpro      USING 'X' 'SAPMIEQ0' '0101'.
    PERFORM bdc_field       USING 'BDC_OKCODE'   '=EQUI'.
    PERFORM bdc_field       USING 'BDC_CURSOR'   'ITOB-CHARGE'.
    PERFORM bdc_dynpro      USING 'X' 'SAPMIEQ0' '0101'.
    PERFORM bdc_field       USING 'BDC_OKCODE'   '=T\01'.
    PERFORM bdc_field       USING 'BDC_CURSOR'   'EQBS-B_LAGER'.
    PERFORM bdc_dynpro      USING 'X' 'SAPMIEQ0' '0101'.
    PERFORM bdc_field       USING 'BDC_CURSOR'   'ITOB-SERGE'.
if p_unpair is initial .
    PERFORM bdc_field       USING 'ITOB-HERST'    wa_final-manf.
*    PERFORM bdc_field       USING 'ITOB-TYPBZ'    wa_final-part.
    PERFORM bdc_field       USING 'ITOB-TYPBZ'    wa_final-model.
    PERFORM bdc_field       USING 'ITOB-MAPAR'    wa_final-part.
    PERFORM bdc_field       USING 'ITOB-SERGE'    wa_final-man_ser.
    PERFORM bdc_field       USING 'ITOB-HERLD'    wa_final-country.
    PERFORM bdc_field       USING 'ITOB-BAUJJ'    wa_final-year.
    PERFORM bdc_field       USING 'ITOB-BAUMM'    wa_final-month.
else .
    PERFORM bdc_field       USING 'ITOB-SERGE'    ''.
endif.
    PERFORM bdc_field       USING 'BDC_OKCODE'   '=BU'.
    CALL TRANSACTION 'IQ02' USING bdcdat
                           MODE pr_mode UPDATE 'A'
                           MESSAGES INTO it_messtab.
    CLEAR: bdcdat[], bdcdat.
    CLEAR: wa_final, wa_messtab.
ENDLOOP .
end-of-selection .

Hi Rachel..
While running the BDC in 'A' Mode check the message that come in the status bar. There could be any screen where just becuase u press enter it is going to the next screen. That is because of your intercation.
But in the case of background this is not hapening and it fails..
So make sure whether when u run in foreground you are pressing any additional enter which is not in your recording. This could be the only problem why it is not updating in background.
Another reson could be that you dont have access to back ground jobs. Check that also..
Regards
Ansari

VS2013 not running in debug mode on Windows 10 Technical Preview Build 10041

am getting the following errors every time i try to run my projects in debug mode what can be the issue.
Managed Debugging Assistant 'FatalExecutionEngineError' has detected a problem in 'C:\Program Files (x86)\IIS Express\iisexpress.exe'.
Additional information: The runtime has encountered a fatal error. The address of the error was at 0x73c0d5a5, on thread 0x1a0c. The error code is 0xc0000005. This error may be a bug in the CLR or in the unsafe or non-verifiable portions of user
code. Common sources of this bug include user marshaling errors for COM-interop or PInvoke, which may corrupt the stack.
Then when I continue the following appears
An unhandled exception of type 'System.AccessViolationException' occurred in System.Data.dll
Additional information: Attempted to read or write protected memory. This is often an indication that other memory is corrupt.
Then it stops..
This happens when a database call is made and only does this when debug, when I run it using the browser link all is good. The applications work well.

Hi Bigmachini,
According to my solution, what about your issue now?
If you have been solved the issue, would you mind sharing us the solution here? So it would be helpful for other members who get the same issue.
If not, please let us know the latest information about it.
@Malik, could you please tell me if you try to check your issue by the above suggestion as I said?
If no, please try the above suggestions to check this issue and then tell me the latest message about this issue.
>>The error mostly occurs when debugging ADO.NET or database function calls. If code is run without debugging then there is no issue at all.
You could also try to copy your project and then debug your project in debug mode on a another machine you install same Windows 10 OS check this issue again.
Best Regards,
We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
Click
HERE to participate the survey.

JDK 1.5 does not run in client mode

Hello all,
I just downloaded JDK 1.5 update 17 for windows 64 bit. This does not support "client" mode. I read forums and found out that other 64 bit vms take the "java -client" argument and internally still work in server mode. Do I have to do some configuration to run this vm in client mode.
Thanks
Anishek

It's just starting the command lines one after the other and after that simply returns a success of starting all the commands. Two things you should do to successfully use a batch file like this:
Use start-wait constructions, so the next action won't start before the previous action is finished. For the exact command lines see:
http://technet.microsoft.com/en-us/library/bb491005.aspx;
First test the batch file with psexec, to see how it behaves with SYSTEM credentials.
My Blog: http://www.petervanderwoude.nl/
Follow me on twitter: pvanderwoude

Satellite L500 - After Windows 7 upgrade games not run in fullscreen mode

Hello..
I just got my windows 7 upgrade in the mail and I installed it and everything is fine..
But if I start a game which is not in the same screen resulution as the computer it is a square in the middle of the screen and it is two big black lines down on each side. It does not put the game in full screen. The games in the same resulution works fine.
Some games cannot be put to the resulution this computer have.
How can I make then come in fullscreen?
thank you

I tryed to update the driver to no affect....
The games are in a fullscreen mode but with black lines on the side it does not understand its a widescreen =/ it worked well on vista....
the known games that have this issue is:
Age of Empires
Saint Rows 2
Emergency/911 first responders 3 and 4
GTA san andreas
The sims 2
Euro Truck Simulator
Swat 4
easyer sayd most of the games with has not 1366 X 768 as an resulution option
(they are playable but its kinda annoying to have a big screen an the game just uses a 50% of it and the rest is black..
-thanks

When running diagnostic one of the problems that comes up is itunes is not running in safe mode,how do i fix

Cannot connect to ITunes Store - Diagnostic report comes up as -secure link to ITunes store failed - how do i fix

''Scotty2015 [[#question-1051017|said]]''
<blockquote>
First time situation occurred folders started to disappear as i read messages TB 31.5.0 win 7 pro 64 bit
Thunderbird user forever got into safe mode and disabled all add-ons - now all folders are visible and all content is accessible back to 2009 used mozback so I have backup restarted TB and back to 3 folders. Inbox gets created with the new emails that arrive. Filters send email to one of the visible folders 'Travel' When you open 'travel' all emails 23 unread are accessible. Go back into 'safe' mode and all folders and emails are present
Thanks
</blockquote>
no extensions , no addons uninstalled thunderbird, deleted all TB folders then rebooted win safe mode and ran Malwarebytes - no malware, rebooted normal windows and downloaded fresh version of TB reloaded profile using mozback. Still the same TB loads showing 3 folders no inbox and should be 2 accounts. Change to safe mode in TB and all files are present and 2 inboxes
i am not losing data just can only see emails when in TB safe mode. What TB profile files could be contaminated?

DFS Servers not running in HA mode

I have a DFS server set up as our main namespace. We then replicate from our remote offices to the main office. The main server is a PDC (yeah, I know). For some reason when the main server is not connected to the remote offices the remote
offices cannot access their files anymore. In addition, the performance of the files feels as if they are working off the PDC as opposed to their branch office server.
I don't have enough posts to post images so.... If I sign into the PDC and bring up the DFS Management, select Namespaces, then select the branch name from the list. I then look at the folder targets tab, right click on the branch name, and it says
under advanced it's the first among all targets. Above it in the list on the right hand side is the PDC name. If I right click on it, etc, it says it's the last among all targets.
So, the way I understand it, the computers in the branch office should see SRV1 as their primary (which is in a closet near them) and our PDC (50 miles away) only when there's a problem with their local server. What *appears* to be happening is the
opposite.

Hi,
Please complete the following actions:
- Checked AD Sites and Services. Made sure that the site to subnet mappings are correct.
- Checked DNS. Made sure the DNS structure with all sites is correct.
- Checked the configuration of all namespaces. We made sure that the "Referrals" tab for every namespace is configured for "Lowest cost".
In the meantime, please refer to the articles below to see if it helps:
You may receive DFS referrals that contain a list of random DFS targets, random SYSVOL or NETLOGON referrals, or experience slow performance when you access a shared folder in a DFS namespace on a Windows Server 2003-based computer
http://support.microsoft.com/kb/905846
DFS Referrals and IPv6: Outta site!
http://blogs.technet.com/b/askds/archive/2009/10/28/dfs-referrals-and-ipv6-outta-site.aspx
Regards,
Mandy
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

K8NSLI Platinum not running in SLI mode

Similar Messages

Maybe you are looking for