K8T FIS2R BIOS 1.8 cannot find NVRAM
Hello,
Today I flashed my BIOS to version 1.8. After flashing (using the DOS methode) I couldn't enter the CMOS setup 8 out of 10 times anymore. This happens before on my system and after a load BIOS defaults and reconfiguring it seems stable, again.
However! One difference got my attention. During POST now I get: Checking NVRAM.. NO NVRAM
I seems to me this BIOS version search for NVRAM at a wrong offset. So clearing the NVRAM is no option anymore.
Does anyone else with 1.8 notist this?
For now I switched back to 1.7. This is (for me) still the most stable version ever.
Hi CCheney and others,
I saw the same address thing while flashing. This is some correspondence to/from MSI (my compliments for there fast response):
Hello sir/madam,
Yes, my system did boot up fine. At least I didn't discover any strang behavior.
I flashed in the 1.8 version again to to a little more testing, including the options you suggested me to try. All with the same result. System keeps booting up without problems.
But while reflashing I notisted the possible cause of the 'problem' I thought allready knew:
When flashing version 1.7 and below the NVRAM is asumed or found at address: 00010000H
When flashing version 1.8 the NVRAM is asumed or found at address 00020000H.
Although it seems my system is running fine I can imagine that I will get problems if the NVRAM needs to be cleared in the future.
Can you confirm this? Or is there another explanation?
With kind regards,
Dear Sir/Madam ,
Thank you for contacting MSI Technical Support.
Abbreviation of Non-Volatile Random Access Memory, a type of memory that retains its contents when power is turned off. One type of NVRAM is SRAM that is made non-volatile by connecting it to a constant power source such as a battery. Another type of NVRAM uses EEPROM chips to save its contents when power is turned off. In this case, NVRAM is composed of a combination of SRAM and EEPROM chips. Checking NVRAM refers to NVRAM is being checked to see if it is valid.
Can the system boot up normally after the message"Checking NVRAM ...No NVRAM" showed? Could you please refer to below suggestions to check it again?
1)clear CMOS .
2)Remove these unnecessary device only leaving CPU, memory, power supply ,VGA card and HDD.
3)Check the CMOS battery.
Thanks for your supporting MSI product. Please feel free to let us know if you still have any further issues or inquires.
Best regards,
MSI Technical Support
Similar Messages
-
BIOS-GPT grub cannot find the root device in LVM setup
Greetings Arch Linux Community,
Recently I started my journey of installing Arch Linux on my VMware Workstation.
I successfully installed the non-LVM instance not long before I noticed the advantages of LVM, then I just started a new Arch Linux setup with LVM.
However, after following the Beginners' Guide and LVM Guide carefully, I ran into a problem on boot that I cannot solve by myself due to my poor knowledge on boot/grub.
Here is the error message:
ERROR: device '4b28d500-8ed3-4fe5-ad26-97fbb01f979b' not found. Skipping fsck
ERROR: Unable to find root device '4b28d500-8ed3-4fe5-ad26-97fbb01f979b'
The error message itself is pretty clear; saying that the root device specified by my grub.cfg cannot be found and thus cannot be loaded.
However, I'm 100% sure that the device is actually there and just for some reason grub cannot see it.
Below please see the info from lsblk, pvdisplay, vgdisplay, lvdisplay, and some related info from fstab, grub.cfg and mkinitcpio.conf:
root@archiso / # lsblk -f
NAME FSTYPE LABEL UUID MOUNTPOINT
fd0
sda
├─sda1
├─sda2 swap a576bed1-929a-4ea5-b771-6b2e3b2e3808
├─sda3 ext4 659e5bcf-b34b-4083-b8e5-e336fdd20c3d /mnt/boot
└─sda4 LVM2_member GNznA5-fwUh-Gw6D-JvY4-rZKJ-d6fP-TIyoRZ
├─VolGroup00-lvroot ext4 4b28d500-8ed3-4fe5-ad26-97fbb01f979b /mnt
└─VolGroup00-lvhome ext4 dc1f1322-8d8e-4456-b61d-95966ae4e25d /mnt/home
sr0 iso9660 ARCH_201405 2014-05-01-05-20-54-00 /run/archiso/bootmnt
loop0 squashfs /run/archiso/sfs/root-image
loop1 ext4 f07bfb26-3377-487a-a022-efd840614a0d
└─arch_root-image ext4 f07bfb26-3377-487a-a022-efd840614a0d /
loop2 ext4 f07bfb26-3377-487a-a022-efd840614a0d
└─arch_root-image ext4 f07bfb26-3377-487a-a022-efd840614a0d /
root@archiso / # pvdisplay
--- Physical volume ---
PV Name /dev/sda4
VG Name VolGroup00
PV Size 8.50 GiB / not usable 2.98 MiB
Allocatable yes (but full)
PE Size 4.00 MiB
Total PE 2175
Free PE 0
Allocated PE 2175
PV UUID GNznA5-fwUh-Gw6D-JvY4-rZKJ-d6fP-TIyoRZ
root@archiso / # vgdisplay
--- Volume group ---
VG Name VolGroup00
System ID
Format lvm2
Metadata Areas 1
Metadata Sequence No 3
VG Access read/write
VG Status resizable
MAX LV 0
Cur LV 2
Open LV 2
Max PV 0
Cur PV 1
Act PV 1
VG Size 8.50 GiB
PE Size 4.00 MiB
Total PE 2175
Alloc PE / Size 2175 / 8.50 GiB
Free PE / Size 0 / 0
VG UUID x8VegQ-OKr6-kNNk-HwHe-xxi1-Ecdt-W9Ydj2
root@archiso / # lvdisplay
--- Logical volume ---
LV Path /dev/VolGroup00/lvroot
LV Name lvroot
VG Name VolGroup00
LV UUID q8LxrZ-PXmf-K2Sl-7SNl-DlsF-IZ3s-2m2eHw
LV Write Access read/write
LV Creation host, time archiso, 2014-05-17 16:24:23 +0000
LV Status available
# open 1
LV Size 5.00 GiB
Current LE 1280
Segments 1
Allocation inherit
Read ahead sectors auto
- currently set to 256
Block device 254:1
--- Logical volume ---
LV Path /dev/VolGroup00/lvhome
LV Name lvhome
VG Name VolGroup00
LV UUID 3q32Nf-CRZz-iYpB-5317-075y-ulj3-uurdwE
LV Write Access read/write
LV Creation host, time archiso, 2014-05-17 16:24:49 +0000
LV Status available
# open 1
LV Size 3.50 GiB
Current LE 895
Segments 1
Allocation inherit
Read ahead sectors auto
- currently set to 256
Block device 254:2
root@archiso / # cat /mnt/etc/fstab
# /etc/fstab: static file system information
# <file system> <dir> <type> <options> <dump> <pass>
# /dev/mapper/VolGroup00-lvroot
UUID=4b28d500-8ed3-4fe5-ad26-97fbb01f979b / ext4 rw,relatime,data=ordered 0 1
# /dev/mapper/VolGroup00-lvhome
UUID=dc1f1322-8d8e-4456-b61d-95966ae4e25d /home ext4 rw,relatime,data=ordered 0 2
# /dev/sda3
UUID=659e5bcf-b34b-4083-b8e5-e336fdd20c3d /boot ext4 rw,relatime,data=ordered 0 2
# /dev/sda2
UUID=a576bed1-929a-4ea5-b771-6b2e3b2e3808 none swap defaults 0 0
root@archiso / # cat /mnt/boot/grub/grub.cfg | grep "root"
set root='lvmid/x8VegQ-OKr6-kNNk-HwHe-xxi1-Ecdt-W9Ydj2/q8LxrZ-PXmf-K2Sl-7SNl-DlsF-IZ3s-2m2eHw'
search --no-floppy --fs-uuid --set=root --hint='lvmid/x8VegQ-OKr6-kNNk-HwHe-xxi1-Ecdt-W9Ydj2/q8LxrZ-PXmf-K2Sl-7SNl-DlsF-IZ3s-2m2eHw' 4b28d500-8ed3-4fe5-ad26-97fbb01f979b
search --no-floppy --fs-uuid --set=root 4b28d500-8ed3-4fe5-ad26-97fbb01f979b
set root='hd0,gpt3'
search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt3 --hint-efi=hd0,gpt3 --hint-baremetal=ahci0,gpt3 659e5bcf-b34b-4083-b8e5-e336fdd20c3d
search --no-floppy --fs-uuid --set=root 659e5bcf-b34b-4083-b8e5-e336fdd20c3d
linux /vmlinuz-linux root=UUID=4b28d500-8ed3-4fe5-ad26-97fbb01f979b rw quiet
set root='hd0,gpt3'
search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt3 --hint-efi=hd0,gpt3 --hint-baremetal=ahci0,gpt3 659e5bcf-b34b-4083-b8e5-e336fdd20c3d
search --no-floppy --fs-uuid --set=root 659e5bcf-b34b-4083-b8e5-e336fdd20c3d
linux /vmlinuz-linux root=UUID=4b28d500-8ed3-4fe5-ad26-97fbb01f979b rw quiet
set root='hd0,gpt3'
search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt3 --hint-efi=hd0,gpt3 --hint-baremetal=ahci0,gpt3 659e5bcf-b34b-4083-b8e5-e336fdd20c3d
search --no-floppy --fs-uuid --set=root 659e5bcf-b34b-4083-b8e5-e336fdd20c3d
linux /vmlinuz-linux root=UUID=4b28d500-8ed3-4fe5-ad26-97fbb01f979b rw quiet
root@archiso / # cat /mnt/etc/mkinitcpio.conf| grep "HOOKS"
# HOOKS
# This is the most important setting in this file. The HOOKS control the
# order in which HOOKS are added. Run 'mkinitcpio -H <hook name>' for
# HOOKS="base"
# HOOKS="base udev autodetect block filesystems"
# HOOKS="base udev block filesystems"
# HOOKS="base udev block mdadm encrypt filesystems"
# HOOKS="base udev block lvm2 filesystems"
HOOKS="base udev autodetect modconf block lvm2 filesystems keyboard fsck"
Last edited by garrio (2014-05-18 00:42:36)Efka wrote:when i was installing Arch, i installed grub on /dev/sda and my sda (gpt )was - sda1 (ext4)for / and sda2(ext4) for /home so when grub is installed it is installed into SDA ( or im wrong? ) but not into sda1 or sda2, but when i was doing my install i didnt made /boot ext4 partition (sda3 ext4 659e5bcf-b34b-4083-b8e5-e336fdd20c3d /mnt/boot) . i think u trying to mount grub into ext4 partition. is this right ? if yes... is it how it suposed to be ?
Sorry, im newbie ( dont take my advice seriously ), but im very curious about his, because once i couldnt install grub as well so i went for syslinux instead , and i know i will have one more fresh install of arch to do, so im curious
Hi Efka, I used grub-install and specified "/dev/sda" for argument. What I understand is that the sda is the identifier for the hard disk where all the sdaX reside. And if you look into the output of my lsblk, you will see that there is one partition sda1 that has no filetype, label and UUID on display; that is actually the bios boot partition where, as I understand, the grub code embeds itself.
We can have different partition scheme to deploy and having a separate partition for /boot is just my personal preference ans it should work as well. -
Using K7T266 Pro2, Cannot find BIOS Protection function.
I am using K7T266 Pro2 (MS-6380 v2.0) with BIOS update 3.70. I was reading the manual and suddenly I found a interesting function “BIOS Protection”, quote from manual:
Quote
This function protects the BIOS from accidental corruption by unauthorized users or computer viruses. When enabled, the BIOS’ data cannot be changed when attempting to update the BIOS with a Flash utility. To successfully update the BIOS, you’ll need to disable this Flash BIOS
This is a really useful function but the problem is that I cannot find it! According to the manual it should be in the Advanced Chipset Features section, below the “PCI Delay Transaction” function. But when I go to my BIOS setup there is nothing below the “PCI Delay Transaction” function. And so I ask my self “where is the BIOS Protection function?”, I checked threw all the other sections but I could not find it… please help me, where is this function? Doesn't it include in the new BIOS update 3.70? Is anyone experiencing the same thing?Quote
Originally posted by elpcmaster
Downgrade to 3.3. It is the best and supports Linux and Norton Ghost, unlike 3.7.
I'm assuming that by this you mean it does not support a network boot?
The reason why I say this is that I recently restored my K7T266 PRO2-RU BIOS Rev. 3.7 using Symantec Ghost Corp. Edition (MultiCast Server). The Ghost image was stored on a remote machine, all that was needed was a floppy disk which was simple enough to configure using the wizard. I had no problems - BUT that doesn't mean the thing (my motherboard) isn't flakey as hell though. -
Xorg cannot find screens with nvidia module
I know that this question is very common, but I cannot find solution,
I should use "nvidia" drivers on Lenovo notebook with two videocards (work with Cuda technology).
Xorg cannot load nvidia module with this xorg.conf. Can anybody help?
Thanks.
lspci | grep VGA
00:02.0 VGA compatible controller: Intel Corporation 3rd Gen Core processor Graphics Controller (rev 09)
01:00.0 VGA compatible controller: NVIDIA Corporation GF108 [GeForce GT 630M] (rev a1)
xorg.conf:
Section "ServerLayout"
Identifier "X.org Configured"
Screen 0 "Screen0" 0 0
# Screen 0 "Screen1" 0 0
# Screen 1 "Screen1" RightOf "Screen0"
InputDevice "Mouse0" "CorePointer"
InputDevice "Keyboard0" "CoreKeyboard"
EndSection
Section "Files"
ModulePath "/usr/lib/xorg/modules"
FontPath "/usr/share/fonts/misc/"
FontPath "/usr/share/fonts/TTF/"
FontPath "/usr/share/fonts/OTF/"
FontPath "/usr/share/fonts/Type1/"
FontPath "/usr/share/fonts/100dpi/"
FontPath "/usr/share/fonts/75dpi/"
EndSection
Section "Module"
Load "glx"
EndSection
Section "InputDevice"
Identifier "Keyboard0"
Driver "kbd"
EndSection
Section "InputDevice"
Identifier "Mouse0"
Driver "mouse"
Option "Protocol" "auto"
Option "Device" "/dev/input/mice"
Option "ZAxisMapping" "4 5 6 7"
EndSection
Section "Monitor"
Identifier "Monitor0"
VendorName "Monitor Vendor"
ModelName "Monitor Model"
EndSection
Section "Monitor"
Identifier "Monitor1"
VendorName "Monitor Vendor"
ModelName "Monitor Model"
EndSection
Section "Device"
### Available Driver options are:-
### Values: <i>: integer, <f>: float, <bool>: "True"/"False",
### <string>: "String", <freq>: "<f> Hz/kHz/MHz",
### <percent>: "<f>%"
### [arg]: arg optional
#Option "SWcursor" # [<bool>]
#Option "HWcursor" # [<bool>]
#Option "NoAccel" # [<bool>]
#Option "ShadowFB" # [<bool>]
#Option "UseFBDev" # [<bool>]
#Option "Rotate" # [<str>]
#Option "VideoKey" # <i>
#Option "FlatPanel" # [<bool>]
#Option "FPDither" # [<bool>]
#Option "CrtcNumber" # <i>
#Option "FPScale" # [<bool>]
#Option "FPTweak" # <i>
#Option "DualHead" # [<bool>]
Identifier "Card0"
Driver "nvidia"
BusID "PCI:1:0:0"
EndSection
Section "Device"
### Available Driver options are:-
### Values: <i>: integer, <f>: float, <bool>: "True"/"False",
### <string>: "String", <freq>: "<f> Hz/kHz/MHz",
### <percent>: "<f>%"
### [arg]: arg optional
#Option "NoAccel" # [<bool>]
#Option "AccelMethod" # <str>
#Option "Backlight" # <str>
#Option "DRI" # [<bool>]
#Option "ColorKey" # <i>
#Option "VideoKey" # <i>
#Option "Tiling" # [<bool>]
#Option "LinearFramebuffer" # [<bool>]
#Option "SwapbuffersWait" # [<bool>]
#Option "XvPreferOverlay" # [<bool>]
#Option "HotPlug" # [<bool>]
#Option "RelaxedFencing" # [<bool>]
#Option "XvMC" # [<bool>]
#Option "Throttle" # [<bool>]
#Option "ZaphodHeads" # <str>
#Option "DelayedFlush" # [<bool>]
#Option "TearFree" # [<bool>]
#Option "PerCrtcPixmaps" # [<bool>]
#Option "FallbackDebug" # [<bool>]
#Option "DebugFlushBatches" # [<bool>]
#Option "DebugFlushCaches" # [<bool>]
#Option "DebugWait" # [<bool>]
#Option "BufferCache" # [<bool>]
#Option "TripleBuffer" # [<bool>]
Identifier "Card1"
Driver "intel"
BusID "PCI:0:2:0"
EndSection
Section "Screen"
Identifier "Screen0"
Device "Card0"
Monitor "Monitor0"
SubSection "Display"
Viewport 0 0
Depth 16
Modes "1366x768"
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 24
Modes "1366x768"
EndSubSection
# SubSection "Display"
# Viewport 0 0
# Depth 32
# Modes "1366x768"
# EndSubSection
EndSection
Section "Screen"
Identifier "Screen1"
Device "Card1"
Monitor "Monitor1"
SubSection "Display"
Viewport 0 0
Depth 16
Modes "1366x768"
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 24
Modes "1366x768"
EndSubSection
# SubSection "Display"
# Viewport 0 0
# Depth 32
# Modes "1366x768"
# EndSubSection
EndSection
Xorg.0.log:
[ 27.732]
X.Org X Server 1.13.0
Release Date: 2012-09-05
[ 27.732] X Protocol Version 11, Revision 0
[ 27.732] Build Operating System: Linux 3.6.2-1-ARCH x86_64
[ 27.732] Current Operating System: Linux kot_dymok 3.5.6-1-ARCH #1 SMP PREEMPT Sun Oct 7 19:30:49 CEST 2012 x86_64
[ 27.732] Kernel command line: BOOT_IMAGE=/vmlinuz-linux root=UUID=fc9d19b7-8701-471d-bf1f-867196c6d392 resume=/dev/disk/by-uuid/007e49dc-18dc-442a-89c8-ab927e6a17ff ro quiet
[ 27.732] Build Date: 19 October 2012 03:54:56PM
[ 27.732]
[ 27.732] Current version of pixman: 0.26.2
[ 27.732] Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
[ 27.732] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[ 27.732] (==) Log file: "/var/log/Xorg.0.log", Time: Fri Oct 26 01:54:00 2012
[ 27.732] (==) Using config file: "/etc/X11/xorg.conf"
[ 27.732] (==) Using config directory: "/etc/X11/xorg.conf.d"
[ 27.732] (==) ServerLayout "X.org Configured"
[ 27.732] (**) |-->Screen "Screen0" (0)
[ 27.732] (**) | |-->Monitor "Monitor0"
[ 27.732] (**) | |-->Device "Card0"
[ 27.732] (**) |-->Input Device "Mouse0"
[ 27.733] (**) |-->Input Device "Keyboard0"
[ 27.733] (==) Automatically adding devices
[ 27.733] (==) Automatically enabling devices
[ 27.733] (==) Automatically adding GPU devices
[ 27.733] (WW) The directory "/usr/share/fonts/OTF/" does not exist.
[ 27.733] Entry deleted from font path.
[ 27.733] (WW) The directory "/usr/share/fonts/OTF/" does not exist.
[ 27.733] Entry deleted from font path.
[ 27.733] (**) FontPath set to:
/usr/share/fonts/misc/,
/usr/share/fonts/TTF/,
/usr/share/fonts/Type1/,
/usr/share/fonts/100dpi/,
/usr/share/fonts/75dpi/,
/usr/share/fonts/misc/,
/usr/share/fonts/TTF/,
/usr/share/fonts/Type1/,
/usr/share/fonts/100dpi/,
/usr/share/fonts/75dpi/
[ 27.733] (**) ModulePath set to "/usr/lib/xorg/modules"
[ 27.733] (WW) Hotplugging is on, devices using drivers 'kbd', 'mouse' or 'vmmouse' will be disabled.
[ 27.733] (WW) Disabling Mouse0
[ 27.733] (WW) Disabling Keyboard0
[ 27.733] (II) Loader magic: 0x7fcc20
[ 27.733] (II) Module ABI versions:
[ 27.733] X.Org ANSI C Emulation: 0.4
[ 27.733] X.Org Video Driver: 13.0
[ 27.733] X.Org XInput driver : 18.0
[ 27.733] X.Org Server Extension : 7.0
[ 27.733] (II) config/udev: Adding drm device (/dev/dri/card0)
[ 27.734] (--) PCI:*(0:0:2:0) 8086:0166:17aa:3901 rev 9, Mem @ 0xd3400000/4194304, 0xe0000000/268435456, I/O @ 0x00004000/64
[ 27.734] (--) PCI: (0:1:0:0) 10de:0de9:17aa:3901 rev 161, Mem @ 0xd2000000/16777216, 0xc0000000/268435456, 0xd0000000/33554432, I/O @ 0x00003000/128, BIOS @ 0x????????/524288
[ 27.734] (II) Open ACPI successful (/var/run/acpid.socket)
[ 27.734] Initializing built-in extension Generic Event Extension
[ 27.734] Initializing built-in extension SHAPE
[ 27.734] Initializing built-in extension MIT-SHM
[ 27.734] Initializing built-in extension XInputExtension
[ 27.734] Initializing built-in extension XTEST
[ 27.734] Initializing built-in extension BIG-REQUESTS
[ 27.734] Initializing built-in extension SYNC
[ 27.734] Initializing built-in extension XKEYBOARD
[ 27.734] Initializing built-in extension XC-MISC
[ 27.734] Initializing built-in extension SECURITY
[ 27.734] Initializing built-in extension XINERAMA
[ 27.734] Initializing built-in extension XFIXES
[ 27.734] Initializing built-in extension RENDER
[ 27.734] Initializing built-in extension RANDR
[ 27.734] Initializing built-in extension COMPOSITE
[ 27.734] Initializing built-in extension DAMAGE
[ 27.734] Initializing built-in extension MIT-SCREEN-SAVER
[ 27.734] Initializing built-in extension DOUBLE-BUFFER
[ 27.734] Initializing built-in extension RECORD
[ 27.734] Initializing built-in extension DPMS
[ 27.735] Initializing built-in extension X-Resource
[ 27.735] Initializing built-in extension XVideo
[ 27.735] Initializing built-in extension XVideo-MotionCompensation
[ 27.735] Initializing built-in extension XFree86-VidModeExtension
[ 27.735] Initializing built-in extension XFree86-DGA
[ 27.735] Initializing built-in extension XFree86-DRI
[ 27.735] Initializing built-in extension DRI2
[ 27.735] (II) "glx" will be loaded. This was enabled by default and also specified in the config file.
[ 27.735] (II) LoadModule: "glx"
[ 27.735] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[ 27.741] (II) Module glx: vendor="NVIDIA Corporation"
[ 27.741] compiled for 4.0.2, module version = 1.0.0
[ 27.741] Module class: X.Org Server Extension
[ 27.741] (II) NVIDIA GLX Module 304.43 Sun Aug 19 20:34:01 PDT 2012
[ 27.741] Loading extension GLX
[ 27.741] (II) LoadModule: "nvidia"
[ 27.741] (II) Loading /usr/lib/xorg/modules/drivers/nvidia_drv.so
[ 27.742] (II) Module nvidia: vendor="NVIDIA Corporation"
[ 27.742] compiled for 4.0.2, module version = 1.0.0
[ 27.742] Module class: X.Org Video Driver
[ 27.815] (EE) NVIDIA: Failed to load the NVIDIA kernel module. Please check your
[ 27.815] (EE) NVIDIA: system's kernel log for additional error messages.
[ 27.815] (II) UnloadModule: "nvidia"
[ 27.815] (II) Unloading nvidia
[ 27.815] (EE) Failed to load module "nvidia" (module-specific error, 0)
[ 27.815] (EE) No drivers available.
[ 27.815]
Fatal server error:
[ 27.815] no screens found
[ 27.815] (EE)
Please consult the The X.Org Foundation support
at http://wiki.x.org
for help.
[ 27.815] (EE) Please also check the log file at "/var/log/Xorg.0.log" for additional information.
[ 27.815] (EE)
dmesg.log
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.5.6-1-ARCH (tobias@T-POWA-LX) (gcc version 4.7.1 20120721 (prerelease) (GCC) ) #1 SMP PREEMPT Sun Oct 7 19:30:49 CEST 2012
[ 0.000000] Command line: BOOT_IMAGE=/vmlinuz-linux root=UUID=fc9d19b7-8701-471d-bf1f-867196c6d392 resume=/dev/disk/by-uuid/007e49dc-18dc-442a-89c8-ab927e6a17ff ro quiet
[ 0.000000] e820: BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009d7ff] usable
[ 0.000000] BIOS-e820: [mem 0x000000000009d800-0x000000000009ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000000e0000-0x00000000000fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000001fffffff] usable
[ 0.000000] BIOS-e820: [mem 0x0000000020000000-0x00000000201fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000020200000-0x0000000040003fff] usable
[ 0.000000] BIOS-e820: [mem 0x0000000040004000-0x0000000040004fff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000040005000-0x00000000baabefff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000baabf000-0x00000000baebefff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000baebf000-0x00000000bafbefff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x00000000bafbf000-0x00000000baffefff] ACPI data
[ 0.000000] BIOS-e820: [mem 0x00000000bafff000-0x00000000baffffff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000bb000000-0x00000000bf9fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000f0000000-0x00000000f3ffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000feb00000-0x00000000feb03fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed10000-0x00000000fed19fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed1c000-0x00000000fed1ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000ffb80000-0x00000000ffffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000013f5fffff] usable
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] DMI 2.7 present.
[ 0.000000] DMI: LENOVO Lenovo G580/Product Name, BIOS 5ECN33WW(V2.03) 06/06/2012
[ 0.000000] e820: update [mem 0x00000000-0x0000ffff] usable ==> reserved
[ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[ 0.000000] No AGP bridge found
[ 0.000000] e820: last_pfn = 0x13f600 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-E7FFF write-protect
[ 0.000000] E8000-EFFFF write-combining
[ 0.000000] F0000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000 mask F80000000 write-back
[ 0.000000] 1 base 080000000 mask FC0000000 write-back
[ 0.000000] 2 base 0BB000000 mask FFF000000 uncachable
[ 0.000000] 3 base 0BC000000 mask FFC000000 uncachable
[ 0.000000] 4 base 0FFC00000 mask FFFC00000 write-protect
[ 0.000000] 5 base 100000000 mask FC0000000 write-back
[ 0.000000] 6 base 13F600000 mask FFFE00000 uncachable
[ 0.000000] 7 base 13F800000 mask FFF800000 uncachable
[ 0.000000] 8 disabled
[ 0.000000] 9 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] e820: last_pfn = 0xbb000 max_arch_pfn = 0x400000000
[ 0.000000] found SMP MP-table at [mem 0x000fe1b0-0x000fe1bf] mapped at [ffff8800000fe1b0]
[ 0.000000] initial memory mapped: [mem 0x00000000-0x1fffffff]
[ 0.000000] Base memory trampoline at [ffff880000097000] 97000 size 24576
[ 0.000000] init_memory_mapping: [mem 0x00000000-0xbaffffff]
[ 0.000000] [mem 0x00000000-0xbaffffff] page 2M
[ 0.000000] kernel direct mapping tables up to 0xbaffffff @ [mem 0x1fa24000-0x1fffffff]
[ 0.000000] init_memory_mapping: [mem 0x100000000-0x13f5fffff]
[ 0.000000] [mem 0x100000000-0x13f5fffff] page 2M
[ 0.000000] kernel direct mapping tables up to 0x13f5fffff @ [mem 0xbaab9000-0xbaabefff]
[ 0.000000] RAMDISK: [mem 0x37a12000-0x37d00fff]
[ 0.000000] ACPI: RSDP 00000000000fe020 00024 (v02 LENOVO)
[ 0.000000] ACPI: XSDT 00000000baffe210 00094 (v01 LENOVO CB-01 00000001 01000013)
[ 0.000000] ACPI: FACP 00000000baffb000 000F4 (v04 LENOVO CB-01 00000001 ACPI 00040000)
[ 0.000000] ACPI: DSDT 00000000bafee000 09755 (v01 LENOVO CB-01 00000001 ACPI 00040000)
[ 0.000000] ACPI: FACS 00000000bafbb000 00040
[ 0.000000] ACPI: UEFI 00000000baffd000 00236 (v01 LENOVO CB-01 00000001 ACPI 00040000)
[ 0.000000] ACPI: ASF! 00000000baffc000 000A5 (v32 LENOVO CB-01 00000001 ACPI 00040000)
[ 0.000000] ACPI: HPET 00000000baffa000 00038 (v01 LENOVO CB-01 00000001 ACPI 00040000)
[ 0.000000] ACPI: APIC 00000000baff9000 0008C (v02 LENOVO CB-01 00000001 ACPI 00040000)
[ 0.000000] ACPI: MCFG 00000000baff8000 0003C (v01 LENOVO CB-01 00000001 ACPI 00040000)
[ 0.000000] ACPI: SLIC 00000000bafed000 00176 (v01 LENOVO CB-01 00000001 ACPI 00040000)
[ 0.000000] ACPI: SSDT 00000000bafec000 006FE (v01 LENOVO CB-01 00001000 ACPI 00040000)
[ 0.000000] ACPI: BOOT 00000000bafea000 00028 (v01 LENOVO CB-01 00000001 ACPI 00040000)
[ 0.000000] ACPI: ASPT 00000000bafe5000 00034 (v07 LENOVO CB-01 00000001 ACPI 00040000)
[ 0.000000] ACPI: FPDT 00000000bafe3000 00044 (v01 LENOVO CB-01 00000001 ACPI 00040000)
[ 0.000000] ACPI: SSDT 00000000bafe2000 00968 (v01 LENOVO CB-01 00003000 ACPI 00040000)
[ 0.000000] ACPI: SSDT 00000000bafe1000 00A92 (v01 LENOVO CB-01 00003000 ACPI 00040000)
[ 0.000000] ACPI: SSDT 00000000bafdf000 01EDD (v01 LENOVO CB-01 00001000 ACPI 00040000)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at [mem 0x0000000000000000-0x000000013f5fffff]
[ 0.000000] Initmem setup node 0 [mem 0x00000000-0x13f5fffff]
[ 0.000000] NODE_DATA [mem 0x13f5fc000-0x13f5fffff]
[ 0.000000] [ffffea0000000000-ffffea0004ffffff] PMD -> [ffff88013ac00000-ffff88013ebfffff] on node 0
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x00010000-0x00ffffff]
[ 0.000000] DMA32 [mem 0x01000000-0xffffffff]
[ 0.000000] Normal [mem 0x100000000-0x13f5fffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00010000-0x0009cfff]
[ 0.000000] node 0: [mem 0x00100000-0x1fffffff]
[ 0.000000] node 0: [mem 0x20200000-0x40003fff]
[ 0.000000] node 0: [mem 0x40005000-0xbaabefff]
[ 0.000000] node 0: [mem 0xbafff000-0xbaffffff]
[ 0.000000] node 0: [mem 0x100000000-0x13f5fffff]
[ 0.000000] On node 0 totalpages: 1023564
[ 0.000000] DMA zone: 64 pages used for memmap
[ 0.000000] DMA zone: 6 pages reserved
[ 0.000000] DMA zone: 3911 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 16320 pages used for memmap
[ 0.000000] DMA32 zone: 743679 pages, LIFO batch:31
[ 0.000000] Normal zone: 4056 pages used for memmap
[ 0.000000] Normal zone: 255528 pages, LIFO batch:31
[ 0.000000] ACPI: PM-Timer IO Port: 0x408
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x00] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x00] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x00] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x08] lapic_id[0x00] disabled)
[ 0.000000] ACPI: IOAPIC (id[0x00] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 0, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[ 0.000000] SMP: Allowing 8 CPUs, 4 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 40
[ 0.000000] PM: Registered nosave memory: 000000000009d000 - 000000000009e000
[ 0.000000] PM: Registered nosave memory: 000000000009e000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
[ 0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
[ 0.000000] PM: Registered nosave memory: 0000000020000000 - 0000000020200000
[ 0.000000] PM: Registered nosave memory: 0000000040004000 - 0000000040005000
[ 0.000000] PM: Registered nosave memory: 00000000baabf000 - 00000000baebf000
[ 0.000000] PM: Registered nosave memory: 00000000baebf000 - 00000000bafbf000
[ 0.000000] PM: Registered nosave memory: 00000000bafbf000 - 00000000bafff000
[ 0.000000] PM: Registered nosave memory: 00000000bb000000 - 00000000bfa00000
[ 0.000000] PM: Registered nosave memory: 00000000bfa00000 - 00000000f0000000
[ 0.000000] PM: Registered nosave memory: 00000000f0000000 - 00000000f4000000
[ 0.000000] PM: Registered nosave memory: 00000000f4000000 - 00000000feb00000
[ 0.000000] PM: Registered nosave memory: 00000000feb00000 - 00000000feb04000
[ 0.000000] PM: Registered nosave memory: 00000000feb04000 - 00000000fec00000
[ 0.000000] PM: Registered nosave memory: 00000000fec00000 - 00000000fec01000
[ 0.000000] PM: Registered nosave memory: 00000000fec01000 - 00000000fed10000
[ 0.000000] PM: Registered nosave memory: 00000000fed10000 - 00000000fed1a000
[ 0.000000] PM: Registered nosave memory: 00000000fed1a000 - 00000000fed1c000
[ 0.000000] PM: Registered nosave memory: 00000000fed1c000 - 00000000fed20000
[ 0.000000] PM: Registered nosave memory: 00000000fed20000 - 00000000fee00000
[ 0.000000] PM: Registered nosave memory: 00000000fee00000 - 00000000fee01000
[ 0.000000] PM: Registered nosave memory: 00000000fee01000 - 00000000ffb80000
[ 0.000000] PM: Registered nosave memory: 00000000ffb80000 - 0000000100000000
[ 0.000000] e820: [mem 0xbfa00000-0xefffffff] available for PCI devices
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] setup_percpu: NR_CPUS:64 nr_cpumask_bits:64 nr_cpu_ids:8 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 28 pages/cpu @ffff88013f200000 s83392 r8192 d23104 u262144
[ 0.000000] pcpu-alloc: s83392 r8192 d23104 u262144 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1 2 3 4 5 6 7
[ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 1003118
[ 0.000000] Policy zone: Normal
[ 0.000000] Kernel command line: BOOT_IMAGE=/vmlinuz-linux root=UUID=fc9d19b7-8701-471d-bf1f-867196c6d392 resume=/dev/disk/by-uuid/007e49dc-18dc-442a-89c8-ab927e6a17ff ro quiet
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] __ex_table already sorted, skipping sort
[ 0.000000] xsave/xrstor: enabled xstate_bv 0x7, cntxt size 0x340
[ 0.000000] Checking aperture...
[ 0.000000] No AGP bridge found
[ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
[ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[ 0.000000] Memory: 3947540k/5232640k available (4661k kernel code, 1138384k absent, 146716k reserved, 4191k data, 760k init)
[ 0.000000] SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] Dump stacks of tasks blocking RCU-preempt GP.
[ 0.000000] NR_IRQS:4352 nr_irqs:744 16
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] allocated 16777216 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] hpet clockevent registered
[ 0.000000] Fast TSC calibration using PIT
[ 0.003333] Detected 2494.278 MHz processor.
[ 0.000002] Calibrating delay loop (skipped), value calculated using timer frequency.. 4990.41 BogoMIPS (lpj=8314260)
[ 0.000004] pid_max: default: 32768 minimum: 301
[ 0.000025] Security Framework initialized
[ 0.000028] AppArmor: AppArmor disabled by boot time parameter
[ 0.000250] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[ 0.001230] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.001662] Mount-cache hash table entries: 256
[ 0.001817] Initializing cgroup subsys cpuacct
[ 0.001818] Initializing cgroup subsys memory
[ 0.001825] Initializing cgroup subsys devices
[ 0.001826] Initializing cgroup subsys freezer
[ 0.001827] Initializing cgroup subsys net_cls
[ 0.001828] Initializing cgroup subsys blkio
[ 0.001850] CPU: Physical Processor ID: 0
[ 0.001850] CPU: Processor Core ID: 0
[ 0.001854] ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
ENERGY_PERF_BIAS: View and update with x86_energy_perf_policy(8)
[ 0.002211] mce: CPU supports 7 MCE banks
[ 0.002221] CPU0: Thermal monitoring enabled (TM1)
[ 0.002227] using mwait in idle threads.
[ 0.003141] ACPI: Core revision 20120320
[ 0.021624] ftrace: allocating 18032 entries in 71 pages
[ 0.029975] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.062936] CPU0: Intel(R) Core(TM) i5-3210M CPU @ 2.50GHz stepping 09
[ 0.166795] Performance Events: PEBS fmt1+, 16-deep LBR, SandyBridge events, Intel PMU driver.
[ 0.166800] ... version: 3
[ 0.166801] ... bit width: 48
[ 0.166802] ... generic registers: 4
[ 0.166803] ... value mask: 0000ffffffffffff
[ 0.166804] ... max period: 000000007fffffff
[ 0.166804] ... fixed-purpose events: 3
[ 0.166805] ... event mask: 000000070000000f
[ 0.186863] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
[ 0.200098] Booting Node 0, Processors #1 #2 #3
[ 0.266902] Brought up 4 CPUs
[ 0.266905] Total of 4 processors activated (19962.65 BogoMIPS).
[ 0.269981] devtmpfs: initialized
[ 0.270796] PM: Registering ACPI NVS region [mem 0xbaebf000-0xbafbefff] (1048576 bytes)
[ 0.271536] NET: Registered protocol family 16
[ 0.271635] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
[ 0.271637] ACPI: bus type pci registered
[ 0.271695] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf0000000-0xf3ffffff] (base 0xf0000000)
[ 0.271697] PCI: MMCONFIG at [mem 0xf0000000-0xf3ffffff] reserved in E820
[ 0.277539] PCI: Using configuration type 1 for base access
[ 0.277665] mtrr: your CPUs had inconsistent variable MTRR settings
[ 0.277666] mtrr: probably your BIOS does not setup all CPUs.
[ 0.277666] mtrr: corrected configuration.
[ 0.277952] bio: create slab <bio-0> at 0
[ 0.277994] ACPI: Added _OSI(Module Device)
[ 0.277995] ACPI: Added _OSI(Processor Device)
[ 0.277996] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.277997] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.279372] ACPI: EC: Look up EC in DSDT
[ 0.280773] ACPI: Executed 1 blocks of module-level executable AML code
[ 0.283353] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored
[ 0.284330] ACPI: SSDT 00000000bae18018 0083B (v01 PmRef Cpu0Cst 00003001 INTL 20100121)
[ 0.284681] ACPI: Dynamic OEM Table Load:
[ 0.284683] ACPI: SSDT (null) 0083B (v01 PmRef Cpu0Cst 00003001 INTL 20100121)
[ 0.284902] ACPI: SSDT 00000000bae19a98 00303 (v01 PmRef ApIst 00003000 INTL 20100121)
[ 0.285275] ACPI: Dynamic OEM Table Load:
[ 0.285277] ACPI: SSDT (null) 00303 (v01 PmRef ApIst 00003000 INTL 20100121)
[ 0.285380] ACPI: SSDT 00000000bae17d98 00119 (v01 PmRef ApCst 00003000 INTL 20100121)
[ 0.285725] ACPI: Dynamic OEM Table Load:
[ 0.285726] ACPI: SSDT (null) 00119 (v01 PmRef ApCst 00003000 INTL 20100121)
[ 0.286579] ACPI: Interpreter enabled
[ 0.286581] ACPI: (supports S0 S3 S4 S5)
[ 0.286600] ACPI: Using IOAPIC for interrupt routing
[ 0.409275] ACPI: EC: GPE = 0x17, I/O: command/status = 0x66, data = 0x62
[ 0.409424] ACPI: No dock devices found.
[ 0.409427] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 0.409682] \_SB_.PCI0:_OSC invalid UUID
[ 0.409683] _OSC request data:1 8 1f
[ 0.409687] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-3e])
[ 0.410085] pci_root PNP0A08:00: >host bridge window [io 0x0000-0x0cf7]
[ 0.410087] pci_root PNP0A08:00: >host bridge window [io 0x0d00-0xffff]
[ 0.410089] pci_root PNP0A08:00: >host bridge window [mem 0x000a0000-0x000bffff]
[ 0.410091] pci_root PNP0A08:00: >host bridge window [mem 0xbfa00000-0xfeafffff]
[ 0.410117] PCI host bridge to bus 0000:00
[ 0.410119] pci_bus 0000:00: >root bus resource [io 0x0000-0x0cf7]
[ 0.410121] pci_bus 0000:00: >root bus resource [io 0x0d00-0xffff]
[ 0.410122] pci_bus 0000:00: >root bus resource [mem 0x000a0000-0x000bffff]
[ 0.410123] pci_bus 0000:00: >root bus resource [mem 0xbfa00000-0xfeafffff]
[ 0.410131] pci 0000:00:00.0: >[8086:0154] type 00 class 0x060000
[ 0.410164] pci 0000:00:01.0: >[8086:0151] type 01 class 0x060400
[ 0.410192] pci 0000:00:01.0: >PME# supported from D0 D3hot D3cold
[ 0.410210] pci 0000:00:02.0: >[8086:0166] type 00 class 0x030000
[ 0.410220] pci 0000:00:02.0: >reg 10: [mem 0xd3400000-0xd37fffff 64bit]
[ 0.410226] pci 0000:00:02.0: >reg 18: [mem 0xe0000000-0xefffffff 64bit pref]
[ 0.410231] pci 0000:00:02.0: >reg 20: [io 0x4000-0x403f]
[ 0.410281] pci 0000:00:14.0: >[8086:1e31] type 00 class 0x0c0330
[ 0.410303] pci 0000:00:14.0: >reg 10: [mem 0xd3a00000-0xd3a0ffff 64bit]
[ 0.410373] pci 0000:00:14.0: >PME# supported from D3hot D3cold
[ 0.410396] pci 0000:00:16.0: >[8086:1e3a] type 00 class 0x078000
[ 0.410419] pci 0000:00:16.0: >reg 10: [mem 0xd3a14000-0xd3a1400f 64bit]
[ 0.410494] pci 0000:00:16.0: >PME# supported from D0 D3hot D3cold
[ 0.410528] pci 0000:00:1a.0: >[8086:1e2d] type 00 class 0x0c0320
[ 0.410779] pci 0000:00:1a.0: >reg 10: [mem 0xd3a19000-0xd3a193ff]
[ 0.412197] pci 0000:00:1a.0: >PME# supported from D0 D3hot D3cold
[ 0.412223] pci 0000:00:1b.0: >[8086:1e20] type 00 class 0x040300
[ 0.412237] pci 0000:00:1b.0: >reg 10: [mem 0xd3a10000-0xd3a13fff 64bit]
[ 0.412305] pci 0000:00:1b.0: >PME# supported from D0 D3hot D3cold
[ 0.412329] pci 0000:00:1c.0: >[8086:1e10] type 01 class 0x060400
[ 0.412408] pci 0000:00:1c.0: >PME# supported from D0 D3hot D3cold
[ 0.412433] pci 0000:00:1c.1: >[8086:1e12] type 01 class 0x060400
[ 0.412512] pci 0000:00:1c.1: >PME# supported from D0 D3hot D3cold
[ 0.412546] pci 0000:00:1d.0: >[8086:1e26] type 00 class 0x0c0320
[ 0.412788] pci 0000:00:1d.0: >reg 10: [mem 0xd3a18000-0xd3a183ff]
[ 0.414203] pci 0000:00:1d.0: >PME# supported from D0 D3hot D3cold
[ 0.414230] pci 0000:00:1f.0: >[8086:1e59] type 00 class 0x060100
[ 0.414353] pci 0000:00:1f.2: >[8086:1e03] type 00 class 0x010601
[ 0.414371] pci 0000:00:1f.2: >reg 10: [io 0x4088-0x408f]
[ 0.414379] pci 0000:00:1f.2: >reg 14: [io 0x4094-0x4097]
[ 0.414387] pci 0000:00:1f.2: >reg 18: [io 0x4080-0x4087]
[ 0.414396] pci 0000:00:1f.2: >reg 1c: [io 0x4090-0x4093]
[ 0.414404] pci 0000:00:1f.2: >reg 20: [io 0x4060-0x407f]
[ 0.414412] pci 0000:00:1f.2: >reg 24: [mem 0xd3a17000-0xd3a177ff]
[ 0.414457] pci 0000:00:1f.2: >PME# supported from D3hot
[ 0.414475] pci 0000:00:1f.3: >[8086:1e22] type 00 class 0x0c0500
[ 0.414491] pci 0000:00:1f.3: >reg 10: [mem 0xd3a15000-0xd3a150ff 64bit]
[ 0.414512] pci 0000:00:1f.3: >reg 20: [io 0x4040-0x405f]
[ 0.414568] pci 0000:01:00.0: >[10de:0de9] type 00 class 0x030000
[ 0.414578] pci 0000:01:00.0: >reg 10: [mem 0xd2000000-0xd2ffffff]
[ 0.414589] pci 0000:01:00.0: >reg 14: [mem 0xc0000000-0xcfffffff 64bit pref]
[ 0.414600] pci 0000:01:00.0: >reg 1c: [mem 0xd0000000-0xd1ffffff 64bit pref]
[ 0.414607] pci 0000:01:00.0: >reg 24: [io 0x3000-0x307f]
[ 0.414615] pci 0000:01:00.0: >reg 30: [mem 0xfff80000-0xffffffff pref]
[ 0.419807] pci 0000:00:01.0: >PCI bridge to [bus 01-01]
[ 0.419812] pci 0000:00:01.0: > bridge window [io 0x3000-0x3fff]
[ 0.419816] pci 0000:00:01.0: > bridge window [mem 0xd2000000-0xd30fffff]
[ 0.419834] pci 0000:00:01.0: > bridge window [mem 0xc0000000-0xd1ffffff 64bit pref]
[ 0.419945] pci 0000:02:00.0: >[1969:1090] type 00 class 0x020000
[ 0.420065] pci 0000:02:00.0: >reg 10: [mem 0xd3900000-0xd393ffff 64bit]
[ 0.420115] pci 0000:02:00.0: >reg 18: [io 0x2000-0x207f]
[ 0.420574] pci 0000:02:00.0: >PME# supported from D0 D1 D2 D3hot D3cold
[ 0.426507] pci 0000:00:1c.0: >PCI bridge to [bus 02-02]
[ 0.426512] pci 0000:00:1c.0: > bridge window [io 0x2000-0x2fff]
[ 0.426516] pci 0000:00:1c.0: > bridge window [mem 0xd3900000-0xd39fffff]
[ 0.426588] pci 0000:03:00.0: >[168c:002b] type 00 class 0x028000
[ 0.426615] pci 0000:03:00.0: >reg 10: [mem 0xd3800000-0xd380ffff 64bit]
[ 0.426744] pci 0000:03:00.0: >supports D1
[ 0.426746] pci 0000:03:00.0: >PME# supported from D0 D1 D3hot
[ 0.433127] pci 0000:00:1c.1: >PCI bridge to [bus 03-03]
[ 0.433150] pci 0000:00:1c.1: > bridge window [mem 0xd3800000-0xd38fffff]
[ 0.433170] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.433258] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
[ 0.433280] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT]
[ 0.433313] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEG0._PRT]
[ 0.433378] \_SB_.PCI0:_OSC invalid UUID
[ 0.433379] _OSC request data:1 1f 1f
[ 0.433382] pci0000:00: >Requesting ACPI _OSC control (0x1d)
[ 0.433416] \_SB_.PCI0:_OSC invalid UUID
[ 0.433417] _OSC request data:1 0 1d
[ 0.433420] pci0000:00: >ACPI _OSC request failed (AE_ERROR), returned control mask: 0x1d
[ 0.433421] ACPI _OSC control for PCIe not granted, disabling ASPM
[ 0.435631] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 10 *11 12 14 15)
[ 0.435669] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 *10 11 12 14 15)
[ 0.435705] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 0.435740] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 *10 11 12 14 15)
[ 0.435774] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 0.435809] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 10 11 12 14 15) *7
[ 0.435844] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 10 11 12 14 15) *7
[ 0.435879] ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 10 *11 12 14 15)
[ 0.435945] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.435951] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=none,locks=none
[ 0.435952] vgaarb: loaded
[ 0.435953] vgaarb: bridge control possible 0000:01:00.0
[ 0.435954] vgaarb: no bridge control possible 0000:00:02.0
[ 0.435977] PCI: Using ACPI for IRQ routing
[ 0.437526] PCI: pci_cache_line_size set to 64 bytes
[ 0.437598] e820: reserve RAM buffer [mem 0x0009d800-0x0009ffff]
[ 0.437599] e820: reserve RAM buffer [mem 0x40004000-0x43ffffff]
[ 0.437600] e820: reserve RAM buffer [mem 0xbaabf000-0xbbffffff]
[ 0.437602] e820: reserve RAM buffer [mem 0xbb000000-0xbbffffff]
[ 0.437603] e820: reserve RAM buffer [mem 0x13f600000-0x13fffffff]
[ 0.437671] NetLabel: Initializing
[ 0.437672] NetLabel: domain hash size = 128
[ 0.437673] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.437681] NetLabel: unlabeled traffic allowed by default
[ 0.437696] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0
[ 0.437700] hpet0: 8 comparators, 64-bit 14.318180 MHz counter
[ 0.439709] Switching to clocksource hpet
[ 0.443743] pnp: PnP ACPI init
[ 0.443758] ACPI: bus type pnp registered
[ 0.444001] pnp 00:00: >[bus 00-3e]
[ 0.444004] pnp 00:00: >[io 0x0000-0x0cf7 window]
[ 0.444005] pnp 00:00: >[io 0x0cf8-0x0cff]
[ 0.444007] pnp 00:00: >[io 0x0d00-0xffff window]
[ 0.444008] pnp 00:00: >[mem 0x000a0000-0x000bffff window]
[ 0.444010] pnp 00:00: >[mem 0x000c0000-0x000c3fff window]
[ 0.444011] pnp 00:00: >[mem 0x000c4000-0x000c7fff window]
[ 0.444012] pnp 00:00: >[mem 0x000c8000-0x000cbfff window]
[ 0.444013] pnp 00:00: >[mem 0x000cc000-0x000cffff window]
[ 0.444015] pnp 00:00: >[mem 0x000d0000-0x000d3fff window]
[ 0.444016] pnp 00:00: >[mem 0x000d4000-0x000d7fff window]
[ 0.444017] pnp 00:00: >[mem 0x000d8000-0x000dbfff window]
[ 0.444019] pnp 00:00: >[mem 0x000dc000-0x000dffff window]
[ 0.444021] pnp 00:00: >[mem 0x000e0000-0x000e3fff window]
[ 0.444023] pnp 00:00: >[mem 0x000e4000-0x000e7fff window]
[ 0.444024] pnp 00:00: >[mem 0x000e8000-0x000ebfff window]
[ 0.444025] pnp 00:00: >[mem 0x000ec000-0x000effff window]
[ 0.444027] pnp 00:00: >[mem 0x000f0000-0x000fffff window]
[ 0.444028] pnp 00:00: >[mem 0xbfa00000-0xfeafffff window]
[ 0.444029] pnp 00:00: >[mem 0x00010000-0x0001ffff window]
[ 0.444084] pnp 00:00: >Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active)
[ 0.444094] pnp 00:01: >[io 0x0000-0x001f]
[ 0.444095] pnp 00:01: >[io 0x0081-0x0091]
[ 0.444096] pnp 00:01: >[io 0x0093-0x009f]
[ 0.444097] pnp 00:01: >[io 0x00c0-0x00df]
[ 0.444099] pnp 00:01: >[dma 4]
[ 0.444115] pnp 00:01: >Plug and Play ACPI device, IDs PNP0200 (active)
[ 0.444121] pnp 00:02: >[mem 0xff010000-0xffffffff]
[ 0.444135] pnp 00:02: >Plug and Play ACPI device, IDs INT0800 (active)
[ 0.444191] pnp 00:03: >[mem 0xfed00000-0xfed003ff]
[ 0.444207] pnp 00:03: >Plug and Play ACPI device, IDs PNP0103 (active)
[ 0.444214] pnp 00:04: >[io 0x00f0]
[ 0.444222] pnp 00:04: >[irq 13]
[ 0.444238] pnp 00:04: >Plug and Play ACPI device, IDs PNP0c04 (active)
[ 0.444246] pnp 00:05: >[io 0x002e-0x002f]
[ 0.444247] pnp 00:05: >[io 0x004e-0x004f]
[ 0.444248] pnp 00:05: >[io 0x0061]
[ 0.444249] pnp 00:05: >[io 0x0063]
[ 0.444251] pnp 00:05: >[io 0x0065]
[ 0.444252] pnp 00:05: >[io 0x0067]
[ 0.444253] pnp 00:05: >[io 0x0070]
[ 0.444254] pnp 00:05: >[io 0x0080]
[ 0.444255] pnp 00:05: >[io 0x0092]
[ 0.444256] pnp 00:05: >[io 0x00b2-0x00b3]
[ 0.444257] pnp 00:05: >[io 0x0680-0x069f]
[ 0.444259] pnp 00:05: >[io 0x1000-0x100f]
[ 0.444260] pnp 00:05: >[io 0xffff]
[ 0.444261] pnp 00:05: >[io 0xffff]
[ 0.444262] pnp 00:05: >[io 0x0400-0x0453]
[ 0.444263] pnp 00:05: >[io 0x0458-0x047f]
[ 0.444264] pnp 00:05: >[io 0x0500-0x057f]
[ 0.444266] pnp 00:05: >[io 0x164e-0x164f]
[ 0.444267] pnp 00:05: >[io 0xfd60-0xfd63]
[ 0.444300] system 00:05: >[io 0x0680-0x069f] has been reserved
[ 0.444302] system 00:05: >[io 0x1000-0x100f] has been reserved
[ 0.444303] system 00:05: >[io 0xffff] has been reserved
[ 0.444305] system 00:05: >[io 0xffff] has been reserved
[ 0.444306] system 00:05: >[io 0x0400-0x0453] has been reserved
[ 0.444308] system 00:05: >[io 0x0458-0x047f] has been reserved
[ 0.444309] system 00:05: >[io 0x0500-0x057f] has been reserved
[ 0.444311] system 00:05: >[io 0x164e-0x164f] has been reserved
[ 0.444312] system 00:05: >[io 0xfd60-0xfd63] has been reserved
[ 0.444315] system 00:05: >Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.444322] pnp 00:06: >[io 0x0070-0x0077]
[ 0.444327] pnp 00:06: >[irq 8]
[ 0.444341] pnp 00:06: >Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.444360] pnp 00:07: >[io 0x0454-0x0457]
[ 0.444385] system 00:07: >[io 0x0454-0x0457] has been reserved
[ 0.444387] system 00:07: >Plug and Play ACPI device, IDs INT3f0d PNP0c02 (active)
[ 0.444394] pnp 00:08: >[io 0x0060]
[ 0.444396] pnp 00:08: >[io 0x0064]
[ 0.444400] pnp 00:08: >[irq 1]
[ 0.444416] pnp 00:08: >Plug and Play ACPI device, IDs PNP0303 (active)
[ 0.444460] pnp 00:09: >[irq 12]
[ 0.444479] pnp 00:09: >Plug and Play ACPI device, IDs ETD0613 ETD0001 PNP0f13 (active)
[ 0.503108] pnp 00:0a: >[mem 0xfed1c000-0xfed1ffff]
[ 0.503110] pnp 00:0a: >[mem 0xfed10000-0xfed17fff]
[ 0.503111] pnp 00:0a: >[mem 0xfed18000-0xfed18fff]
[ 0.503113] pnp 00:0a: >[mem 0xfed19000-0xfed19fff]
[ 0.503114] pnp 00:0a: >[mem 0xf0000000-0xf3ffffff]
[ 0.503115] pnp 00:0a: >[mem 0xfed20000-0xfed3ffff]
[ 0.503116] pnp 00:0a: >[mem 0xfed90000-0xfed93fff]
[ 0.503117] pnp 00:0a: >[mem 0xff000000-0xff000fff]
[ 0.503119] pnp 00:0a: >[mem 0xff010000-0xffffffff]
[ 0.503120] pnp 00:0a: >[mem 0xfee00000-0xfeefffff]
[ 0.503121] pnp 00:0a: >[mem 0xbfa00000-0xbfa00fff]
[ 0.503153] system 00:0a: >[mem 0xfed1c000-0xfed1ffff] has been reserved
[ 0.503154] system 00:0a: >[mem 0xfed10000-0xfed17fff] has been reserved
[ 0.503156] system 00:0a: >[mem 0xfed18000-0xfed18fff] has been reserved
[ 0.503159] system 00:0a: >[mem 0xfed19000-0xfed19fff] has been reserved
[ 0.503161] system 00:0a: >[mem 0xf0000000-0xf3ffffff] has been reserved
[ 0.503162] system 00:0a: >[mem 0xfed20000-0xfed3ffff] has been reserved
[ 0.503164] system 00:0a: >[mem 0xfed90000-0xfed93fff] has been reserved
[ 0.503165] system 00:0a: >[mem 0xff000000-0xff000fff] has been reserved
[ 0.503167] system 00:0a: >[mem 0xff010000-0xffffffff] could not be reserved
[ 0.503169] system 00:0a: >[mem 0xfee00000-0xfeefffff] could not be reserved
[ 0.503170] system 00:0a: >[mem 0xbfa00000-0xbfa00fff] has been reserved
[ 0.503173] system 00:0a: >Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.503426] pnp 00:0b: >[mem 0x20000000-0x201fffff]
[ 0.503428] pnp 00:0b: >[mem 0x40004000-0x40004fff]
[ 0.503467] system 00:0b: >[mem 0x20000000-0x201fffff] has been reserved
[ 0.503469] system 00:0b: >[mem 0x40004000-0x40004fff] has been reserved
[ 0.503471] system 00:0b: >Plug and Play ACPI device, IDs PNP0c01 (active)
[ 0.503484] pnp: PnP ACPI: found 12 devices
[ 0.503485] ACPI: ACPI bus type pnp unregistered
[ 0.509719] pci 0000:01:00.0: >no compatible bridge window for [mem 0xfff80000-0xffffffff pref]
[ 0.509749] pci 0000:01:00.0: >BAR 6: assigned [mem 0xd3000000-0xd307ffff pref]
[ 0.509751] pci 0000:00:01.0: >PCI bridge to [bus 01-01]
[ 0.509753] pci 0000:00:01.0: > bridge window [io 0x3000-0x3fff]
[ 0.509756] pci 0000:00:01.0: > bridge window [mem 0xd2000000-0xd30fffff]
[ 0.509758] pci 0000:00:01.0: > bridge window [mem 0xc0000000-0xd1ffffff 64bit pref]
[ 0.509761] pci 0000:00:1c.0: >PCI bridge to [bus 02-02]
[ 0.509764] pci 0000:00:1c.0: > bridge window [io 0x2000-0x2fff]
[ 0.509769] pci 0000:00:1c.0: > bridge window [mem 0xd3900000-0xd39fffff]
[ 0.509778] pci 0000:00:1c.1: >PCI bridge to [bus 03-03]
[ 0.509783] pci 0000:00:1c.1: > bridge window [mem 0xd3800000-0xd38fffff]
[ 0.509815] pci_bus 0000:00: >resource 4 [io 0x0000-0x0cf7]
[ 0.509816] pci_bus 0000:00: >resource 5 [io 0x0d00-0xffff]
[ 0.509818] pci_bus 0000:00: >resource 6 [mem 0x000a0000-0x000bffff]
[ 0.509819] pci_bus 0000:00: >resource 7 [mem 0xbfa00000-0xfeafffff]
[ 0.509821] pci_bus 0000:01: >resource 0 [io 0x3000-0x3fff]
[ 0.509822] pci_bus 0000:01: >resource 1 [mem 0xd2000000-0xd30fffff]
[ 0.509824] pci_bus 0000:01: >resource 2 [mem 0xc0000000-0xd1ffffff 64bit pref]
[ 0.509825] pci_bus 0000:02: >resource 0 [io 0x2000-0x2fff]
[ 0.509827] pci_bus 0000:02: >resource 1 [mem 0xd3900000-0xd39fffff]
[ 0.509828] pci_bus 0000:03: >resource 1 [mem 0xd3800000-0xd38fffff]
[ 0.509849] NET: Registered protocol family 2
[ 0.509940] IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.510462] TCP established hash table entries: 524288 (order: 11, 8388608 bytes)
[ 0.511934] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 0.512121] TCP: Hash tables configured (established 524288 bind 65536)
[ 0.512123] TCP: reno registered
[ 0.512131] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[ 0.512148] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[ 0.512215] NET: Registered protocol family 1
[ 0.512227] pci 0000:00:02.0: >Boot video device
[ 0.539686] PCI: CLS 64 bytes, default 64
[ 0.539720] Unpacking initramfs...
[ 0.587463] Freeing initrd memory: 3004k freed
[ 0.587782] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 0.587786] software IO TLB [mem 0xb6ab9000-0xbaab8fff] (64MB) mapped at [ffff8800b6ab9000-ffff8800baab8fff]
[ 0.587808] Simple Boot Flag at 0x44 set to 0x1
[ 0.588188] audit: initializing netlink socket (disabled)
[ 0.588201] type=2000 audit(1351239412.473:1): initialized
[ 0.598216] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.599469] VFS: Disk quotas dquot_6.5.2
[ 0.599501] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.599601] msgmni has been set to 7715
[ 0.599760] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 0.599785] io scheduler noop registered
[ 0.599786] io scheduler deadline registered
[ 0.599824] io scheduler cfq registered (default)
[ 0.599901] pcieport 0000:00:01.0: >irq 40 for MSI/MSI-X
[ 0.600058] vesafb: mode is 1366x768x32, linelength=5504, pages=0
[ 0.600059] vesafb: scrolling: redraw
[ 0.600061] vesafb: Truecolor: size=8:8:8:8, shift=24:16:8:0
[ 0.600464] vesafb: framebuffer at 0xe0000000, mapped to 0xffffc90005100000, using 4160k, total 4160k
[ 0.667429] Console: switching to colour frame buffer device 170x48
[ 0.734140] fb0: VESA VGA frame buffer device
[ 0.734147] intel_idle: does not run on family 6 model 58
[ 0.734170] GHES: HEST is not enabled!
[ 0.734209] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 0.734579] Linux agpgart interface v0.103
[ 0.734634] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:MSS4] at 0x60,0x64 irq 1,12
[ 0.748568] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.748578] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 0.748663] mousedev: PS/2 mouse device common for all mice
[ 0.748692] rtc_cmos 00:06: >RTC can wake from S4
[ 0.748829] rtc_cmos 00:06: >rtc core: registered rtc_cmos as rtc0
[ 0.748861] rtc0: alarms up to one month, 242 bytes nvram, hpet irqs
[ 0.748868] cpuidle: using governor ladder
[ 0.748870] cpuidle: using governor menu
[ 0.748966] drop_monitor: Initializing network drop monitor service
[ 0.749023] TCP: cubic registered
[ 0.749094] NET: Registered protocol family 10
[ 0.749220] NET: Registered protocol family 17
[ 0.749227] Key type dns_resolver registered
[ 0.749314] PM: Checking hibernation image partition /dev/disk/by-uuid/007e49dc-18dc-442a-89c8-ab927e6a17ff
[ 0.762323] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[ 0.775385] PM: Hibernation image not present or could not be loaded.
[ 0.775393] registered taskstats version 1
[ 0.775839] rtc_cmos 00:06: >setting system clock to 2012-10-26 08:16:53 UTC (1351239413)
[ 0.776874] Freeing unused kernel memory: 760k freed
[ 0.776957] Write protecting the kernel read-only data: 8192k
[ 0.780137] Freeing unused kernel memory: 1472k freed
[ 0.781606] Freeing unused kernel memory: 608k freed
[ 0.787240] systemd-udevd[47]: starting version 194
[ 0.813888] ACPI: bus type usb registered
[ 0.813910] usbcore: registered new interface driver usbfs
[ 0.813918] usbcore: registered new interface driver hub
[ 0.813955] usbcore: registered new device driver usb
[ 0.815211] SCSI subsystem initialized
[ 0.816356] libata version 3.00 loaded.
[ 0.816442] xhci_hcd 0000:00:14.0: >setting latency timer to 64
[ 0.816447] xhci_hcd 0000:00:14.0: >xHCI Host Controller
[ 0.816456] xhci_hcd 0000:00:14.0: >new USB bus registered, assigned bus number 1
[ 0.816560] xhci_hcd 0000:00:14.0: >cache line size of 64 is not supported
[ 0.816578] xhci_hcd 0000:00:14.0: >irq 21, io mem 0xd3a00000
[ 0.816632] xhci_hcd 0000:00:14.0: >irq 41 for MSI/MSI-X
[ 0.816791] xHCI xhci_add_endpoint called for root hub
[ 0.816793] xHCI xhci_check_bandwidth called for root hub
[ 0.816874] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.816904] hub 1-0:1.0: >USB hub found
[ 0.816914] hub 1-0:1.0: >4 ports detected
[ 0.817280] xhci_hcd 0000:00:14.0: >xHCI Host Controller
[ 0.817286] xhci_hcd 0000:00:14.0: >new USB bus registered, assigned bus number 2
[ 0.817469] xHCI xhci_add_endpoint called for root hub
[ 0.817471] xHCI xhci_check_bandwidth called for root hub
[ 0.817493] hub 2-0:1.0: >USB hub found
[ 0.817500] hub 2-0:1.0: >4 ports detected
[ 0.822755] ehci_hcd 0000:00:1a.0: >setting latency timer to 64
[ 0.822761] ehci_hcd 0000:00:1a.0: >EHCI Host Controller
[ 0.822768] ehci_hcd 0000:00:1a.0: >new USB bus registered, assigned bus number 3
[ 0.822798] ehci_hcd 0000:00:1a.0: >debug port 2
[ 0.826690] ehci_hcd 0000:00:1a.0: >cache line size of 64 is not supported
[ 0.826709] ehci_hcd 0000:00:1a.0: >irq 16, io mem 0xd3a19000
[ 0.835913] ehci_hcd 0000:00:1a.0: >USB 2.0 started, EHCI 1.00
[ 0.836049] hub 3-0:1.0: >USB hub found
[ 0.836052] hub 3-0:1.0: >2 ports detected
[ 0.836166] ehci_hcd 0000:00:1d.0: >setting latency timer to 64
[ 0.836170] ehci_hcd 0000:00:1d.0: >EHCI Host Controller
[ 0.836177] ehci_hcd 0000:00:1d.0: >new USB bus registered, assigned bus number 4
[ 0.836203] ehci_hcd 0000:00:1d.0: >debug port 2
[ 0.840097] ehci_hcd 0000:00:1d.0: >cache line size of 64 is not supported
[ 0.840110] ehci_hcd 0000:00:1d.0: >irq 23, io mem 0xd3a18000
[ 0.849231] ehci_hcd 0000:00:1d.0: >USB 2.0 started, EHCI 1.00
[ 0.849353] hub 4-0:1.0: >USB hub found
[ 0.849356] hub 4-0:1.0: >2 ports detected
[ 0.849406] ahci 0000:00:1f.2: >version 3.0
[ 0.849473] ahci 0000:00:1f.2: >irq 42 for MSI/MSI-X
[ 0.849524] ahci: SSS flag set, parallel bus scan disabled
[ 0.862579] ahci 0000:00:1f.2: >AHCI 0001.0300 32 slots 6 ports 6 Gbps 0x5 impl SATA mode
[ 0.862582] ahci 0000:00:1f.2: >flags: 64bit ncq stag pm led clo pio slum part ems apst
[ 0.862586] ahci 0000:00:1f.2: >setting latency timer to 64
[ 0.869649] scsi0 : ahci
[ 0.869722] scsi1 : ahci
[ 0.869780] scsi2 : ahci
[ 0.869834] scsi3 : ahci
[ 0.869889] scsi4 : ahci
[ 0.869943] scsi5 : ahci
[ 0.870010] ata1: SATA max UDMA/133 abar m2048@0xd3a17000 port 0xd3a17100 irq 42
[ 0.870011] ata2: DUMMY
[ 0.870014] ata3: SATA max UDMA/133 abar m2048@0xd3a17000 port 0xd3a17200 irq 42
[ 0.870015] ata4: DUMMY
[ 0.870016] ata5: DUMMY
[ 0.870016] ata6: DUMMY
[ 1.142189] usb 3-1: >new high-speed USB device number 2 using ehci_hcd
[ 1.188798] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 1.242364] ata1.00: ATA-8: ST9500325AS, 0011LVM1, max UDMA/100
[ 1.242367] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 1.244122] ata1.00: configured for UDMA/100
[ 1.244233] scsi 0:0:0:0: >Direct-Access ATA ST9500325AS 0011 PQ: 0 ANSI: 5
[ 1.265963] hub 3-1:1.0: >USB hub found
[ 1.266053] hub 3-1:1.0: >6 ports detected
[ 1.371886] usb 4-1: >new high-speed USB device number 2 using ehci_hcd
[ 1.495531] hub 4-1:1.0: >USB hub found
[ 1.495628] hub 4-1:1.0: >6 ports detected
[ 1.561668] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1.561806] usb 3-1.3: >new full-speed USB device number 3 using ehci_hcd
[ 1.566490] ata3.00: ATAPI: PLDS DVD-RW DS8A8SH, KL31, max UDMA/100
[ 1.567395] ata3.00: configured for UDMA/100
[ 1.569763] scsi 2:0:0:0: >CD-ROM PLDS DVD-RW DS8A8SH KL31 PQ: 0 ANSI: 5
[ 1.572713] sd 0:0:0:0: >[sda] 976773168 512-byte logical blocks: (500 GB/465 GiB)
[ 1.572771] sd 0:0:0:0: >[sda] Write Protect is off
[ 1.572774] sd 0:0:0:0: >[sda] Mode Sense: 00 3a 00 00
[ 1.572806] sd 0:0:0:0: >[sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.579557] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[ 1.579561] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 1.579683] sr 2:0:0:0: >Attached scsi CD-ROM sr0
[ 1.588282] Refined TSC clocksource calibration: 2494.333 MHz.
[ 1.588300] Switching to clocksource tsc
[ 1.646147] sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 sda9 >
[ 1.646510] sd 0:0:0:0: >[sda] Attached SCSI disk
[ 1.711612] usb 3-1.4: >new high-speed USB device number 4 using ehci_hcd
[ 1.861415] usb 4-1.6: >new high-speed USB device number 3 using ehci_hcd
[ 3.905748] EXT4-fs (sda7): mounted filesystem with ordered data mode. Opts: (null)
[ 6.297029] systemd-udevd[165]: starting version 194
[ 6.879435] ACPI: Requesting acpi_cpufreq
[ 6.901533] Monitor-Mwait will be used to enter C-1 state
[ 6.901538] Monitor-Mwait will be used to enter C-2 state
[ 6.901542] ACPI: acpi_idle registered with cpuidle
[ 7.242423] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:02/PNP0C0C:00/input/input1
[ 7.242428] ACPI: Power Button [PWRB]
[ 7.243055] ACPI: AC Adapter [ACAD] (on-line)
[ 7.243224] input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:02/PNP0C0E:00/input/input2
[ 7.243227] ACPI: Sleep Button [SLPB]
[ 7.243264] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input3
[ 7.243282] ACPI: Lid Switch [LID0]
[ 7.243312] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input4
[ 7.243314] ACPI: Power Button [PWRF]
[ 7.250773] thermal LNXTHERM:00: >registered as thermal_zone0
[ 7.250778] ACPI: Thermal Zone [TZ00] (54 C)
[ 7.450794] ACPI: Battery Slot [BAT1] (battery present)
[ 7.582945] microcode: CPU0 sig=0x306a9, pf=0x10, revision=0x12
[ 7.612108] microcode: CPU1 sig=0x306a9, pf=0x10, revision=0x12
[ 7.612381] microcode: CPU2 sig=0x306a9, pf=0x10, revision=0x12
[ 7.612637] microcode: CPU3 sig=0x306a9, pf=0x10, revision=0x12
[ 7.612948] microcode: Microcode Update Driver: v2.00 <[email protected]>, Peter Oruba
[ 7.634516] input: Ideapad extra buttons as /devices/platform/ideapad/input/input5
[ 7.648434] Compat-wireless backport release: compat-wireless-v3.6-rc6-1-npc
[ 7.648436] Backport based on linux-stable.git v3.6-rc6
[ 7.648436] compat.git: linux-stable.git
[ 7.734886] ACPI Warning: 0x0000000000000428-0x000000000000042f SystemIO conflicts with Region \PMIO 1 (20120320/utaddress-251)
[ 7.734890] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 7.734893] ACPI Warning: 0x0000000000000500-0x000000000000053f SystemIO conflicts with Region \GPIO 1 (20120320/utaddress-251)
[ 7.734896] ACPI Warning: 0x0000000000000500-0x000000000000053f SystemIO conflicts with Region \_SB_.PCI0.PEG0.PEGP.GPIO 2 (20120320/utaddress-251)
[ 7.734898] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 7.734899] lpc_ich: Resource conflict(s) found affecting gpio_ich
[ 7.737294] mei 0000:00:16.0: >setting latency timer to 64
[ 7.737362] mei 0000:00:16.0: >irq 43 for MSI/MSI-X
[ 7.743686] mei 0000:00:16.0: >wd: failed to find the client
[ 7.757142] agpgart-intel 0000:00:00.0: >Intel Ivybridge Chipset
[ 7.757223] agpgart-intel 0000:00:00.0: >detected gtt size: 2097152K total, 262144K mappable
[ 7.758105] agpgart-intel 0000:00:00.0: >detected 65536K stolen memory
[ 7.758213] agpgart-intel 0000:00:00.0: >AGP aperture is 256M @ 0xe0000000
[ 7.972440] Qualcomm Atheros(R) AR813x/AR815x/AR816x PCI-E Ethernet Network Driver
[ 7.972474] alx 0000:02:00.0: >DMA to 64-BIT addresses
[ 7.972555] alx 0000:02:00.0: >(unregistered net_device): HW Flags = 0x15
[ 7.973019] alx 0000:02:00.0: >(unregistered net_device): reset PHY, pws = 1, az = 0, ptp = 0
[ 7.974361] alx 0000:02:00.0: >(unregistered net_device): speed = 0x2f, autoneg = 1
[ 7.975707] alx 0000:02:00.0: >irq 44 for MSI/MSI-X
[ 7.975824] alx: Atheros Gigabit Network Connection
[ 7.977650] snd_hda_intel 0000:00:1b.0: >irq 45 for MSI/MSI-X
[ 8.008080] [drm] Initialized drm 1.1.0 20060810
[ 8.066122] iTCO_vendor_support: vendor-support=0
[ 8.075437] rts5139: module is from the staging directory, the quality is unknown, you have been warned.
[ 8.078855] scsi6 : SCSI emulation for RTS5139 USB card reader
[ 8.078971] scsi 6:0:0:0: >Direct-Access Generic- xD/SD/M.S. 1.00 PQ: 0 ANSI: 0 CCS
[ 8.080194] sd 6:0:0:0: >[sdb] Attached SCSI removable disk
[ 8.080898] usbcore: registered new interface driver rts5139
[ 8.166428] cfg80211: Calling CRDA to update world regulatory domain
[ 8.175247] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.07
[ 8.175288] iTCO_wdt: Found a Panther Point TCO device (Version=2, TCOBASE=0x0460)
[ 8.175343] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 8.188460] Linux media interface: v0.10
[ 8.307532] Linux video capture interface: v2.00
[ 8.337832] uvcvideo: Found UVC 1.00 device Lenovo EasyCamera (04f2:b2e2)
[ 8.339661] input: Lenovo EasyCamera as /devices/pci0000:00/0000:00:1d.0/usb4/4-1/4-1.6/4-1.6:1.0/input/input6
[ 8.339707] usbcore: registered new interface driver uvcvideo
[ 8.339708] USB Video Class driver (1.1.1)
[ 8.477762] Bluetooth: Core ver 2.16
[ 8.477776] NET: Registered protocol family 31
[ 8.477777] Bluetooth: HCI device and connection manager initialized
[ 8.477779] Bluetooth: HCI socket layer initialized
[ 8.477780] Bluetooth: L2CAP socket layer initialized
[ 8.477784] Bluetooth: SCO socket layer initialized
[ 8.491954] usbcore: registered new interface driver btusb
[ 8.639211] hda_codec: CX20590: BIOS auto-probing.
[ 8.640020] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input7
[ 8.672690] psmouse serio1: >elantech: assuming hardware version 3 (with firmware version 0x450f02)
[ 8.697264] psmouse serio1: >elantech: Synaptics capabilities query result 0x78, 0x17, 0x0b.
[ 8.709692] input: HDA Intel PCH HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8
[ 8.709766] input: HDA Intel PCH Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input9
[ 8.709813] input: HDA Intel PCH Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input10
[ 8.710242] ACPI Warning: 0x0000000000004040-0x000000000000405f SystemIO conflicts with Region \_SB_.PCI0.SBUS.SMBI 1 (20120320/utaddress-251)
[ 8.710247] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 8.710479] checking generic (e0000000 410000) vs hw (e0000000 10000000)
[ 8.710481] fb: conflicting fb hw usage inteldrmfb vs VESA VGA - removing generic driver
[ 8.710502] Console: switching to colour dummy device 80x25
[ 8.710580] i915 0000:00:02.0: >setting latency timer to 64
[ 8.744483] i915 0000:00:02.0: >irq 46 for MSI/MSI-X
[ 8.744490] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 8.744491] [drm] Driver supports precise vblank timestamp query.
[ 8.745029] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=none:owns=io+mem
[ 8.745030] vgaarb: transferring owner from PCI:0000:00:02.0 to PCI:0000:01:00.0
[ 8.825185] input: ETPS/2 Elantech Touchpad as /devices/platform/i8042/serio1/input/input11
[ 9.132101] nvidia: disagrees about version of symbol module_layout
[ 9.243757] usbcore: registered new interface driver ath3k
[ 9.265032] usb 3-1.3: >USB disconnect, device number 3
[ 9.265920] systemd-udevd[329]: failed to execute '/opt/VirtualBox/VBoxCreateUSBNode.sh' '/opt/VirtualBox/VBoxCreateUSBNode.sh --remove 189 258': No such file or directory
[ 9.273016] [drm] Enabling RC6 states: RC6 on, RC6p on, RC6pp off
[ 9.400084] ath: EEPROM regdomain: 0x65
[ 9.400085] ath: EEPROM indicates we should expect a direct regpair map
[ 9.400087] ath: Country alpha2 being used: 00
[ 9.400088] ath: Regpair used: 0x65
[ 9.421060] fbcon: inteldrmfb (fb0) is primary device
[ 9.487637] ieee80211 phy0: >Selected rate control algorithm 'ath9k_rate_control'
[ 9.487781] Registered led device: ath9k-phy0
[ 9.487785] ieee80211 phy0: >Atheros AR9285 Rev:2 mem=0xffffc900050e0000, irq=17
[ 9.552614] kvm: disabled by bios
[ 9.556577] kvm: disabled by bios
[ 9.601270] Console: switching to colour frame buffer device 170x48
[ 9.602975] fb0: inteldrmfb frame buffer device
[ 9.602976] drm: registered panic notifier
[ 9.603101] [Firmware Bug]: ACPI(PEGP) defines _DOD but not _DOS
[ 9.605310] acpi device:38: >registered as cooling_device4
[ 9.605524] ACPI: Video Device [PEGP] (multi-head: yes rom: yes post: no)
[ 9.605938] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:36/LNXVIDEO:00/input/input12
[ 9.611483] acpi device:44: >registered as cooling_device5
[ 9.611810] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
[ 9.611971] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:01/input/input13
[ 9.612048] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[ 9.960891] usb 3-1.3: >new full-speed USB device number 5 using ehci_hcd
[ 10.048160] systemd-udevd[343]: failed to execute '/opt/VirtualBox/VBoxCreateUSBNode.sh' '/opt/VirtualBox/VBoxCreateUSBNode.sh 189 260 e0': No such file or directory
[ 11.761061] EXT4-fs (sda7): re-mounted. Opts: data=ordered
[ 11.956330] EXT4-fs (sda5): mounted filesystem with ordered data mode. Opts: data=ordered
[ 12.074341] EXT4-fs (sda8): mounted filesystem with ordered data mode. Opts: data=ordered
[ 12.321742] fuse init (API version 7.19)
[ 12.703502] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null)
[ 12.770085] EXT4-fs (sda3): mounted filesystem with ordered data mode. Opts: (null)
[ 12.840886] EXT4-fs (sda9): mounted filesystem with ordered data mode. Opts: (null)
[ 12.906640] Adding 16016768k swap on /dev/sda6. Priority:-1 extents:1 across:16016768k
I'm sorry for my English.
Last edited by Kot Dymok (2012-10-26 08:29:53)I don't see any messages of loading nvidia ("NVRM") or nouveau. Are you sure that you have installed a module that is compatible with your current kernel?
You'll also need to patch your ACPI handle or the nouveau/nvidia driver will refuse to load at all, see https://github.com/Bumblebee-Project/bbswitch/issues/2 (this is specific to some machines, your Lenovo G580 machine included)
Last edited by Lekensteyn (2012-10-29 14:52:55) -
X1 Carbon Touch Fingerprint reader 'cannot find fingerprint sensor device' e7210005
Hi all,
I've spent far too long trying to solve this by myself, and need to reach out to someone who might have resolved this issue. I've read tons of similar questions online, and rebooted dozens of times after trying many different things.
I have a Carbon Touch 3444-CUU that can't see it's fingerprint reader. It used to work when brand new, but after lots of lenovo and windows updates, it now does not:
I am on Windows 8.1, with all updates.
No problems in device manager.
Touchchip Fingerprint Coprocessor (WBF advanced mode) installed under Biometric devices fine.
Power management set to _not_ turn off device to save power.
The bios is 2.61.
I suspect the problem is very low-level, because even the BIOS cannot find device when trying to set it up.
If I have the lates BIOS, but it can't see the device - what can I do?
Thanks everyone..
Solved!
Go to Solution.BleachedWhale......which settings you have changed in the BIOS......
It is possible to work-around the issue, but some manual steps are needed:
1. delete "smihlp.sys" from "c:\program files\thinkvantage fingerprint software"
2. run "services.msc" and stop the service "Windows Biometric Service"
3. delete the file "031D23AD-15AF-4e25-B7B3-DE34893097ED.DAT" from "c:\Windows\system32\WinBioDatabase"
4. reboot the computer (important!!)
5. now try to enroll some fingers
This should make it possible to enroll fingerprint and use it to log into Windows, until the bug can be fixed in some future version of BIOS and/or Fingerprint software.
Best regards from Germany.... -
K7N2 Delta2 :: Onboard NIC Once Flawless, Now cannot find Network
Hello, and thank you for reading my Support Query!
Heres the Deal. For the past Couple of Months, I've had little to no problems with my K7N2D2. Everything worked to my expectations.
Until Last Night, was online, and downloading some Bittorrent Files when all my connections suddenly drop'd from Maximum to Nothing.
First Thought : ADSL Dropped or Router Stalled... So, I Restart ze Modem, Restart the Hub. All their Flashes go Normally, and I wait a few moments for everything to Synch Up. Then Tried refreshing google.com .. to No Avail, its -instantly- reporting it cannot find the address, yadda yadda.
2nd Thought : Oh, maybe Verizon's Service was interrupted... But No, I walk into the other room, where my Bro's Comp is at, and the Net is Fully Functional and Online. [ He also has a K7N2-D2 MB.. The Comp which im typing at right now]
Weirdness : I Cannot Connect to the Routers IP Address. I Cannot even Connect to any other the computers on the Network. [ This all Used to Work Perfectly, Small Home Network of 3 Comps, With Lots of Read Only Shared Folders, for Music / Movies ]
Continued Wierdness : Everything in the Device Manager seems to Say everything is in perfect working Order, and I Can Ping Local Address [ 127.0.0.1 ] With No Problem. I Tried Pinging the Router, but it couldnt find Destination?
ipconfig/all Reports that, DHCP is Enabled, AutoConfig is Enabled, but it cant find the Gateway or DHCP Server.
What is going on? Did I Fry the NIC with too Many Torrents?
I Tried Hooking up a Old D-Link NIC Card I've had around for awhile, Not Sure why but it didnt want to Work.. Maybe cuzz its been sitting in storage for years.
Help is greatly appreciated, Is there anyway I Can run a diagnostic on the Onboard NIC? Yarr.Hi all.
I'm new here, but have to write, coz I have exactly the same problem, like Nookovski.
I'm using my K7N2 D2platinum for more than 1 years, without any problem, using the onboard LAN for internet (connected to ADSL cable modem), and another Ethernet card for internal LAN.
2 days ago, I was playing network game with friends, when suddenly my connection was lost. I tried to reach homepages, but no avail. Try to ping some common addresses, nothing happens, 100% lost.
I rebooted, and saw, that my ip address for netconnection changed to 163... etc. This is weird, coz originally my ISP always give some 80... etc from DHCP.
I tried renew my ip, no success.
Called my ISP, they said, they can see my modem, but can't see my PC. I have to plug the cable to my another ethernet card for a moment - I did it, and they saw my pc in this case. They adviced to reinstall my onboard NIC driver. OK, perhaps later.
After all, I found an old Ethernet card (Realtek family) in my case, so I installed it. After a quick reboot my netconnection was fine through this new card. So no network problem on ISP side, there is something with my onboard LAN.
I tried to uninstall / remove the driver from hardware settings panel, but the window freezes. If I reboot in safe mode, and try to remove again, windows says : cannot remove, device is needed for operation. (or smth like this)
I tried reinstall LAN components from the latest MSI driverset, but nothing changed. I think it cannot overwrite the old (damaged?) files.
Now I'm using 2 PCI eth.card, one to connect with another PC, and one for internet. I disabled the onboard LAN from bios. But this is annoying, I don't understand what happend from one minute to another, and I would like to use my integrated NIC!
I found some posts here, advising to set the MAC address in bios manually, regarding to a sticker on the mobo, but I don't have such an option in BIOS.
What should I do now? Are there any solution?
Thanx! -
Since I downloaded Maverick, I cannot find my External Hard Drive in the "Finder" area. I have to unplug all the time the hard drive to be recognized by my iMac. How can I fix this problem? Thank You.
Check Finderr->Preferences->General and ensure that HDs are selected for display. If so and they still don't, Reset the NVRAM/PRAM and Reset the SMC, and see if that does the trick.
-
within the update BIOS file i dloaded there is a "HOW TO FLASH BIOS.doc" but i do not know which section to follow - AMI or AWARD or (i guess) NON_FAT32 i need to know because i am trying to get my 2*512 OCZ 3700EB to work
Hi
The Via board, thats the K8t FIS2R and FSRs use AMI Bios.
Easiest way is to make a floppy with live update, then reboot with it in drive A:. BUT REMEMBER TO DISABLE THE BOOT VIRUS PROTECTION IN THE STANDARD CMOS FEATURES IN BIOS.
The ready made bios/rescue disks are on http://www.M_M.ME.UK/macs use download list and AMD logo. Read the text, it tells you to overwrite all files EXCEPT the COMMAND.COM, to a formatted Ms Dos Startup disk(tick the item in format)
However, I do not think the bios upgrade will help the RAM, I am not sure that RAM is compatable with this board, is it on the MSI list, or in the stickies at top.
DO NOT FLASH if you are not sure, and if the comp is having problems with mem, you will corrupt the bios, and make mobo useless, get an acceptable ram before flashing. Even an old DDR2100 is better, the cheaper and more basic the RAM the better. RAM must be UNregistered and UNbuffered, NON ECC
Cheers
jocko -
I am currently trying to dual boot Windows 8 and Arch Linux. I have Windows 8 installed on my first boot device and Arch installed as per the Beginner's Wiki to my second boot device (both SSD's, sdb and sdc, respectively).
lsblk:
sda [RAID controlled by dedicated card]
sda1 128M
sda2 3.7T
sdb
sdb1 300M
sdb2 100M
sdb3 128M
sdb4 232.4G
sdc
sdc1 500M
sdc2 20G /
sdc3 10G /var
sdc4 200G /home
sdc5 235.3G (spare)
Everything appears to be installed and configured correctly, and I have installed GRUB and gummiboot after GRUB did not work. This was partly do to me having to change some bios settings so that secure boot was disabled, or at least set to "Other OS". At an earlier point I actually wiped my /boot and re-installed Arch (which I believe only replaced missing files) and re-installed grub and re-generated the configuration file.
Now, the GRUB menu shows properly on boot with my Arch and Windows entries and I am able to boot into Arch fine. However, now when I select MS Windows, Grub tells me that it cannot find the chainload command. Is it supposed to be just 'chain', perhaps?
In my /etc/grub.d/40_custom file I added two menu entries, one for Arch Linux and one for MS Windows.
menuentry "Arch Linux" {
set root=(hd2,2)
linux /boot/vmlinuz-linux
initrd /boot/initrd.img
# This was added as per the advice at: http://unix.stackexchange.com/questions … gpt-system
menuentry "MS Windows" {
insmod part_gpt
insmod search_fs_uuid
insmod ntfs
insmod chain
search --fs-uuid 3A781C97781C544B --set=root --hint-bios=hd1,gpt4 --hint-efi=hd1,gpt4 --hint-baremetal=ahci1,gpt4
chainload (${root})/Windows/Boot/EFI/bootmgfw.efi
What could this be?
Thank you for any and all suggestions!!I'm not opposed to gummiboot, like I said it was my first choice, but as I encountered problems I took the guide advice and tried GRUB. If I can get GRUB to work and it increases my understanding, I would be all for it. I'm definitely familiar with Linux, but I don't have extensive experience with GRUB and EFI.
What is the best way to use gummiboot? Uninstall GRUB or install them side-by-side?
Here is the output of parted -l:
parted -l]http://www.hrtmn.net/Images/parted.png
And here is the output of lsblk:
parted -l]http://www.hrtmn.net/Images/lsblk.png
bootmgfw.efi:
parted -l]http://www.hrtmn.net/Images/bootmgfw.png
Moderator edit: Redacted huge images
Last edited by ewaller (2015-04-16 04:41:27) -
Solaris 10 x86 b72 "Cannot find boot.bin" booting from SCSI.
Hello,
After several gyrations of installation attempts and dealing with early BIOS PnP issues, I've finally managed to get Solaris 10 x86 installed on an old dual P2 333Mhz system. So far the system is running flawlessly, but I'm still not able to boot directly off the SCSI disk. The primary boot handler is erroring out that it cannot find boot.bin.
I can boot fine off of the IDE CD drive and the floppy (currently pointed to autoboot into the SCSI disk as a workaround). But when I try to boot directly off the SCSI drive, I get the error from the Solaris boot manager that it "Cannot find boot.bin".
I have booted off the CD & Floppy and compared the /boot files from both the CD & floppy, but I cannot find any difference that would prevent the primary boot loader from finding boot.bin. I've even compared files to make sure they were not corrupt, and even force re-installed the boot handlers, and manually partioning, always with the same results. I've also tried both enabling and disabling the DOS >1G translation of the Adaptec SCSI BIOS with no change. I can't find any reason that the boot loader is not seeing boot.bin, or that the file is corrupt in any way (even after several wipe and install attempts).
My System is:
Supermicro P6DLS dual Pentium II 333MHz & 512MB RAM, w/ Adaptec 7880 SCSI-UW and IDE (whopping UltraDMA 33) interfaces.
CD/DVD reader is configured as the secondary master (moved from primary master in an attempt to fix boot problem)
HD is a 16GB UW SCSI disk.
(Other particulars ommited unless someone feels they are relevant to the boot process).
The system came to me with Windows 2000 installed and functioning. I also had Fedora Core 3 installed, both with no boot problems of the SCSI disk. (Although FC3 would not see the second processor even with the canned SMP kernel).
This system is intended to replace a Fedora Core 3 system to be a multi-purpose firewall gateway & proxy server and I'm really liking the performance I'm seeing with Solaris 10 on this system but would like it to be able to go through a normal boot process and not have to depend on a floppy as a boot device to get started.
Anyone have any ideas why the Solaris x86 boot loaders think that they cannot find boot.bin when the full /boot partion is intact?
TIA,
-TroyI'm getting the same problem trying to install
Solaris 10 in VMware from DVD.
It brings up the Solaris Primary Boot Subsystem, so
it appears to be reading fine, but the only thing
that happens is I get the Cannot find boot.bin
error.Hmm, the "Cannot find boot.bin." message comes from the
CD/DVD's boot code, which is contained in the first 16 sectors
of the media.
The boot.bin file is supposed to be read from the Solaris UFS
slice, which starts at 512 byte block #5151360 (or 2048 byte
dvd sector #1287840). This a byte offset of ~2.6 GBytes.
Maybe an issue with your system's bios not being able to read
DVD media > 2GB, during DVD boot?
Or a problem with burning the DVD media? Maybe some
"smart" PC DVD burning software has decided only to record
the 2.6 GB ISO filesystem, and the 100 MB Solaris UFS
filesystem that follows the ISO filesystem is missing on the DVD?
Or a 2GB filesize issue while burning the DVD?
Do you have a pc / windows utility that can print some information
about the S10 DVD media, especially the size of that DVD?
Maybe your CD/DVD recording software?
The original S10 GA x86 DVD image has a size of 2732195840
bytes, or 1334080 2K DVD blocks. -
Satellite A65-S126: Cannot find the RTC battery
I have my machine turn down but cannot find the batteries to replace them. Based on Toshiba support the P/N are P000444350 but there is no such item in the case that I can see. Any ideas..?
Even the disassembly manuals online do not show them.
I know there must be something in here.
Also according to the operation manual these batteries take power from the main battery.
Since my main battery is completely dead, would this account for the time snyc issue I'm having with the RTC batteries; since they are not getting power to recharge??Sorry for my misunderstanding but what battery do you mean exactly.
Do you mean the main battery or the tiny RTC battery which is fixed on the motherboard?!
> Also according to the operation manual these batteries take power from the main battery.
This is not exactly right.
The RTC battery provides power to the motherboard therewith the internal clock and the BIOS can run 24/7.
It does no matter if the main battery is empty. The RTC should provide the power to motherboard for several times also if the main battery is empty.
If the RTC battery is empty the motherboard cannot be provided with power and the internal clock, BIOS will be reset.
In such case you have to connect the main battery and the AC adaptor to the notebook and let the battery charge for about 12 hours.
For details please check the user manual -> battery chapter
best regards -
Bitlocker "The system cannot find the file specified"
I am trying to get Bitlocker working on the C: drive of a Dell Venue 11 (5130) 32bit, running Windows 8.1Update Enterprise. I click Turn on BitLocker and the system checks the perrequisites and is happy. Then I type in a PIN (6 numbers) and confirm it and
hit Set PIN. At this point it fails with a message saying "The system cannot find the file specified".
I am an Admin on the machine. TPM is working fine. GPO is not setting either BitLocker or TPM to store on the AD DS. Secure Boot is turned on in BIOS. Plus I've tried the reverse of all of these.
I've spent hours reading through web articles without any joy, so I'm hoping someone can give me a pointer. Please.Hi guys,
Almost have the same problem, and still not able to solve it now [despite lots of search].
I used to have BitLocker working on my laptop, but I removed it before cloning [with Paragon] my SSD to a new and bigger one. When I replaced the SSD the system did not boot, and I had to create a new BCD store by copying UEFI boot files from the system
directory on fix the UEFI boot partition. When the boot problem was fixed, I used gParted to extend my C: partition and delete useless recovery partitons at the end of the drive. So actual partitioning is as follow [as per Diskpart]:
Partition ### Type Size Offset
Partition 1 Recovery 500 MB 1024 KB
Partition 2 System 300 MB 501 MB
Partition 3 Reserved 128 MB 801 MB
Partition 4 Primary 930 GB 929 MB
So I guess I made something wrong when I tried to repair the UEFI boot partition... Well, now it boots correctly, but I can't enable BitLocker anymore and get the not-so-explicit "The system cannot find the file specified" error you had. Here is
what I get with a "bcdedit.exe /enum ALL":
Firmware Boot Manager
identifier {fwbootmgr}
displayorder {bootmgr}
{d10304b6-5db7-11e4-bf1c-806e6f6e6963
{d10304b1-5db7-11e4-bf1c-806e6f6e6963
{d10304b2-5db7-11e4-bf1c-806e6f6e6963
{d10304b4-5db7-11e4-bf1c-806e6f6e6963
{d10304b3-5db7-11e4-bf1c-806e6f6e6963
{d10304b5-5db7-11e4-bf1c-806e6f6e6963
timeout 0
Windows Boot Manager
identifier {bootmgr}
device partition=\Device\HarddiskVolume2
path \EFI\Microsoft\Boot\bootmgfw.efi
description Windows Boot Manager
locale en-gb
inherit {globalsettings}
default {current}
resumeobject {4496c237-5dd0-11e4-be46-f1ba631dfb0b
displayorder {current}
toolsdisplayorder {memdiag}
timeout 30
Firmware Application (101fffff)
identifier {d10304ae-5db7-11e4-bf1c-806e6f6e6963
description Setup
Firmware Application (101fffff)
identifier {d10304af-5db7-11e4-bf1c-806e6f6e6963
description Boot Menu
Firmware Application (101fffff)
identifier {d10304b0-5db7-11e4-bf1c-806e6f6e6963
description Recovery
Firmware Application (101fffff)
identifier {d10304b1-5db7-11e4-bf1c-806e6f6e6963
description SATA HDD:
Firmware Application (101fffff)
identifier {d10304b2-5db7-11e4-bf1c-806e6f6e6963
description USB CD:
Firmware Application (101fffff)
identifier {d10304b3-5db7-11e4-bf1c-806e6f6e6963
description USB FDD:
Firmware Application (101fffff)
identifier {d10304b4-5db7-11e4-bf1c-806e6f6e6963
description USB HDD:
Firmware Application (101fffff)
identifier {d10304b5-5db7-11e4-bf1c-806e6f6e6963
description NETWORK:
Firmware Application (101fffff)
identifier {d10304b6-5db7-11e4-bf1c-806e6f6e6963
device partition=\Device\HarddiskVolume2
path \EFI\Microsoft\Boot\bootmgfw.efi
description Windows Boot Manager
Windows Boot Loader
identifier {current}
device partition=C:
path \Windows\system32\winload.efi
description Windows 8.1
locale en-gb
inherit {bootloadersettings}
isolatedcontext Yes
allowedinmemorysettings 0x15000075
osdevice partition=C:
systemroot \Windows
resumeobject {4496c237-5dd0-11e4-be46-f1ba631dfb0b
nx OptIn
bootmenupolicy Standard
detecthal Yes
Resume from Hibernate
identifier {4496c237-5dd0-11e4-be46-f1ba631dfb0b
device partition=C:
path \Windows\system32\winresume.efi
description Windows Resume Application
locale en-gb
inherit {resumeloadersettings}
isolatedcontext Yes
allowedinmemorysettings 0x15000075
filedevice partition=C:
filepath \hiberfil.sys
bootmenupolicy Standard
debugoptionenabled No
Windows Memory Tester
identifier {memdiag}
device partition=\Device\HarddiskVolume2
path \EFI\Microsoft\Boot\memtest.efi
description Windows Memory Diagnostic
locale en-gb
inherit {globalsettings}
badmemoryaccess Yes
EMS Settings
identifier {emssettings}
bootems No
Debugger Settings
identifier {dbgsettings}
debugtype Serial
debugport 1
baudrate 115200
RAM Defects
identifier {badmemory}
badmemorylist 0x10007
Global Settings
identifier {globalsettings}
inherit {dbgsettings}
{emssettings}
{badmemory}
Boot Loader Settings
identifier {bootloadersettings}
inherit {globalsettings}
{hypervisorsettings}
Hypervisor Settings
identifier {hypervisorsettings}
hypervisordebugtype Serial
hypervisordebugport 1
hypervisorbaudrate 115200
Resume Loader Settings
identifier {resumeloadersettings}
inherit {globalsettings}
I also enabled Fast Bios and ACHI Mode in my BIOS [along with enabling Secure Boot on UEFI mode], as well as tried to clear TPM and reinitialize it, but that didn't change anything. And thanks to your posts I had a look to C:\Windows\System32\Recovery\ReAgent.xml
but it does not seem to be populated with the any GUIDs:
<?xml version='1.0' encoding='utf-8'?>
<WindowsRE version="2.0">
<WinreBCD id="{24b2af92-fddf-11e1-bfa1-001377e67dbe}"/>
<WinreLocation path="\Recovery\WindowsRE" id="0" offset="254619418624" guid="{f2ebfdb1-aa8c-453d-9c40-68aed6c32395}"/>
<ImageLocation path="" id="0" offset="0" guid="{00000000-0000-0000-0000-000000000000}"/>
<PBRImageLocation path="" id="0" offset="0" guid="{00000000-0000-0000-0000-000000000000}" index="0"/>
<PBRCustomImageLocation path="" id="0" offset="0" guid="{00000000-0000-0000-0000-000000000000}" index="0"/>
<InstallState state="1"/>
<OsInstallAvailable state="0"/>
<CustomImageAvailable state="0"/>
<IsAutoRepairOn state="1"/>
<WinREStaged state="0"/>
<OperationParam path=""/>
<OsBuildVersion path="9600.16384.amd64fre.winblue_rtm.130821-1623"/>
<OemTool state="0"/>
<IsServer state="0"/>
<DownlevelWinreLocation path="\Recovery\WindowsRE" id="0" offset="1048576" guid="{f2ebfdb1-aa8c-453d-9c40-68aed6c32395}"/>
<IsWimBoot state="0"/>
<ScheduledOperation state="5"/>
</WindowsRE>
Nevertheless I have a ReAgent_Merged.xml1 file in that same folder, which contains:
<?xml version='1.0' encoding='utf-8'?>
<WindowsRE version="1.0">
<WinreBCD id="{24b2af8c-fddf-11e1-bfa1-001377e67dbe}"/>
<WinreLocation path="\Recovery\WindowsRE" id="0" offset="1048576" guid="{f2ebfdb1-aa8c-453d-9c40-68aed6c32395}"/>
<ImageLocation path="\recovery\WindowsRE" id="0" offset="1048576" guid="{f2ebfdb1-aa8c-453d-9c40-68aed6c32395}"/>
<OsInstallLocation path="\RecoveryImage" id="0" offset="231720616448" guid="{f2ebfdb1-aa8c-453d-9c40-68aed6c32395}" index="1"/>
<CustomImageLocation path="" id="0" offset="0" guid="{00000000-0000-0000-0000-000000000000}" index="0"/>
<InstallState state="1"/>
<OsInstallAvailable state="1"/>
<CustomImageAvailable state="0"/>
<IsAutoRepairOn state="1"/>
<WinREStaged state="0"/>
<OperationParam path=""/>
<OsBuildVersion path="9200.16384.amd64fre.win8_rtm.120725-1247"/>
<OemTool state="0"/>
<BootKey state="0"/>
<IsServer state="0"/>
<ScheduledOperation state="4"/>
</WindowsRE>
So I'm stuck, and any pointer would be greatly appreciated. :-/
Cheers,
Kwansetsu -
[SOLVED] Installing on ZFS root: "ZFS: cannot find bootfs" on boot.
I have been experimenting with ZFS filesystems on external HDDs for some time now to get more comfortable with using ZFS in the hopes of one day reinstalling my system on a ZFS root.
Today, I tried installing a system on an USB external HDD, as my first attempt to install on ZFS (I wanted to try in a safe, disposable environment before I try this on my main system).
My partition configuration (from gdisk):
Command (? for help): p
Disk /dev/sdb: 3907024896 sectors, 1.8 TiB
Logical sector size: 512 bytes
Disk identifier (GUID): 2FAE5B61-CCEF-4E1E-A81F-97C8406A07BB
Partition table holds up to 128 entries
First usable sector is 34, last usable sector is 3907024862
Partitions will be aligned on 8-sector boundaries
Total free space is 0 sectors (0 bytes)
Number Start (sector) End (sector) Size Code Name
1 34 2047 1007.0 KiB EF02 BIOS boot partition
2 2048 264191 128.0 MiB 8300 Linux filesystem
3 264192 3902828543 1.8 TiB BF00 Solaris root
4 3902828544 3907024862 2.0 GiB 8300 Linux filesystem
Partition #1 is for grub, obviously. Partition #2 is an ext2 partition that I mount on /boot in the new system. Partition #3 is where I make my ZFS pool.
Partition #4 is an ext4 filesystem containing another minimal Arch system for recovery and setup purposes. GRUB is installed on the other system on partition #4, not in the new ZFS system.
I let grub-mkconfig generate a config file from the system on partition #4 to boot that. Then, I manually edited the generated grub.cfg file to add this menu entry for my ZFS system:
menuentry 'ZFS BOOT' --class arch --class gnu-linux --class gnu --class os {
load_video
set gfxpayload=keep
insmod gzio
insmod part_gpt
insmod ext2
set root='hd0,gpt2'
echo 'Loading Linux core repo kernel ...'
linux /vmlinuz-linux zfs=bootfs zfs_force=1 rw quiet
echo 'Loading initial ramdisk ...'
initrd /initramfs-linux.img
My ZFS configuration:
# zpool list
NAME SIZE ALLOC FREE CAP DEDUP HEALTH ALTROOT
External2TB 1.81T 6.06G 1.81T 0% 1.00x ONLINE -
# zpool status :(
pool: External2TB
state: ONLINE
scan: none requested
config:
NAME STATE READ WRITE CKSUM
External2TB ONLINE 0 0 0
usb-WD_Elements_1048_575836314135334C32383131-0:0-part3 ONLINE 0 0 0
errors: No known data errors
# zpool get bootfs
NAME PROPERTY VALUE SOURCE
External2TB bootfs External2TB/ArchSystemMain local
# zfs list
NAME USED AVAIL REFER MOUNTPOINT
External2TB 14.6G 1.77T 30K none
External2TB/ArchSystemMain 293M 1.77T 293M /
External2TB/PacmanCache 5.77G 1.77T 5.77G /var/cache/pacman/pkg
External2TB/Swap 8.50G 1.78T 20K -
The reason for the above configuration is that after I get this system to work, I want to install a second system in the same zpool on a different dataset, and have them share a pacman cache.
GRUB "boots" successfully, in that it loads the kernel and the initramfs as expected from the 2nd GPT partition. The problem is that the kernel does not load the ZFS:
ERROR: device '' not found. Skipping fsck.
ZFS: Cannot find bootfs.
ERROR: Failed to mount the real root device.
Bailing out, you are on your own. Good luck.
and I am left in busybox in the initramfs.
What am I doing wrong?
Also, here is my /etc/fstab in the new system:
# External2TB/ArchSystemMain
#External2TB/ArchSystemMain / zfs rw,relatime,xattr 0 0
# External2TB/PacmanCache
#External2TB/PacmanCache /var/cache/pacman/pkg zfs rw,relatime,xattr 0 0
UUID=8b7639e2-c858-4ff6-b1d4-7db9a393578f /boot ext4 rw,relatime 0 2
UUID=7a37363e-9adf-4b4c-adfc-621402456c55 none swap defaults 0 0
I also tried to boot using "zfs=External2TB/ArchSystemMain" in the kernel options, since that was the more logical way to approach my intention of having multiple systems on different datasets. It would allow me to simply create separate grub menu entries for each, with different boot datasets in the kernel parameters. I also tried setting the mount points to "legacy" and uncommenting the zfs entries in my fstab above. That didn't work either and produced the same results, and that was why I decided to try to use "bootfs" (and maybe have a script for switching between the systems by changing the ZFS bootfs and mountpoints before reboot, reusing the same grub menuentry).
Thanks in advance for any help.
Last edited by tajjada (2013-12-30 20:03:09)Sounds like a zpool.cache issue. I'm guessing your zpool.cache inside your arch-chroot is not up to date. So on boot the ZFS hook cannot find the bootfs. At least, that's what I assume the issue is, because of this line:
ERROR: device '' not found. Skipping fsck.
If your zpool.cache was populated, it would spit out something other than an empty string.
Some assumptions:
- You're using the ZFS packages provided by demizer (repository or AUR).
- You're using the Arch Live ISO or some version of it.
On cursory glance your configuration looks good. But verify anyway. Here are the steps you should follow to make sure your zpool.cache is correct and up to date:
Outside arch-chroot:
- Import pools (not using '-R') and verify the mountpoints.
- Make a copy of the /etc/zfs/zpool.cache before you export any pools. Again, make a copy of the /etc/zfs/zpool.cache before you export any pools. The reason for this is once you export a pool the /etc/zfs/zpool.cache gets updated and removes any reference to the exported pool. This is likely the cause of your issue, as you would have an empty zpool.cache.
- Import the pool containing your root filesystem using the '-R' flag, and mount /boot within.
- Make sure to copy your updated zpool.cache to your arch-chroot environment.
Inside arch-chroot:
- Make sure your bootloader is configured properly (i.e. read 'mkinitcpio -H zfs').
- Use the 'udev' hook and not the 'systemd' one in your mkinitcpio.conf. The zfs-utils package does not have a ported hook (as of 0.6.2_3.12.6-1).
- Update your initramfs.
Outside arch-chroot:
- Unmount filesystems.
- Export pools.
- Reboot.
Inside new system:
- Make sure to update the hostid then rebuild your initramfs. Then you can drop the 'zfs_force=1'.
Good luck. I enjoy root on ZFS myself. However, I wouldn't recommend swap on ZFS. Despite what the ZoL tracker says, I still ran into deadlocks on occasion (as of a month ago). However, I cannot say definitely the cause of the issue; but it resolved when I moved swap off ZFS to a dedicated partition.
Last edited by NVS (2013-12-29 14:56:44) -
Cannot find a Vector within a Vector
Yo. Another noob askin about elements within a Vector.
I'm working on a OOP project in BlueJ. First time doing so, so my code is still kinda procedural (with many listeners in the same document, etc etc)
I'm creating a simulation of a 7-a-side football game. I have stored the players of each team into a vector (e.g Vector 'Chelsea' would contain 7 player objects).
I've only created three teams for simplicity, and stored these three Vectors into another Vector called 'teams'.
(the whole purpose of storing them in vectors btw, is so I don't have to pass many different player objects as arguments -
i can just send the vector, and extract them within the Listener classes)
I'm now in the new class (Start_game) and i've passed the vector to the class.
When I use the statement:
if (teams.contains(Arsenal))
+some code+
}I get the error message: cannot find variable 'Arsenal', when I try to compile the program.
Here's the code for the first class:
* Write a description of class MainWindow here.
* @author (your name)
* @version (a version number or a date)
import java.awt.*;
import java.awt.event.*;
import javax.swing.*;
import java.util.*;
import java.util.Vector;
import javax.swing.BoxLayout;
public class Choose_player
String t_chosen1;
String t_chosen2;
TextArea playerinfo1;
TextArea playerinfo2;
Vector teams = new Vector();
// Vector Arsenal = new Vector(4); // this will store Player objects with "Arsenal" in their team variable
Vector Arsenal = new Vector(4);
Player Adebayor = new Striker();
Player Walcott = new Striker();
Player Fabregas = new Midfielder();
Player Denilson = new Midfielder();
Player Gallas = new Defender();
Player Eboue = new Defender();
Player Lehmann = new Goalkeeper();
// Arsenal.insertElementAt(Adebayor, 0);
// <Player>Arsenal</Player>.addElement(<Player>Adebayor);
// learn collections - BIG TYME - refer to java site (url is in txt file)
Vector Chelsea = new Vector(4); // this vector will store the Player objects whose team variable
// contains the String "Chelsea"
Player Drogba = new Striker();
Player Anelka = new Striker();
Player Lampard = new Midfielder();
Player Phillips = new Midfielder();
Player ACole = new Defender();
Player Terry = new Defender();
Player Cech = new Goalkeeper();
// int w = Chelsea.Size();
Vector ManU = new Vector(4); // this vector will store the Player objects whose team variable
// contains the String "ManU"
Player Rooney = new Striker();
Player Tevez = new Striker();
Player Giggs = new Midfielder();
Player Ronaldo = new Midfielder();
Player Ferdinand = new Defender();
Player Brown = new Defender();
Player Sar = new Goalkeeper();
public void mainfalse(String t1, String t2)
this.t_chosen1 = t1;
this.t_chosen2 = t2;
Frame m_frame = new mainframe("Select Captain", t_chosen1, t_chosen2, teams);
m_frame.setSize(1200, 700);
m_frame.setVisible(true);
class mainframe extends Frame
Vector teams;
public mainframe(String title, String t_chosen1, String t_chosen2, Vector teams)
super(title);
this.teams = teams;
setLayout(new FlowLayout());
// setLayout(new GridLayout());
// setLayout(new CardLayout());
// setLayout(new RelativeLayout());
// setLayout(new BoxLayout(m_frame, - FINISH EDITING BoxLayout statement
// -------- ADD PLAYERS TO VECTOR -------- //
Arsenal.addElement(Adebayor);
Arsenal.addElement(Walcott);
Arsenal.addElement(Fabregas);
Arsenal.addElement(Denilson);
Arsenal.addElement(Gallas);
Arsenal.addElement(Eboue);
Arsenal.addElement(Lehmann);
Chelsea.addElement(Drogba);
Chelsea.addElement(Anelka);
Chelsea.addElement(Lampard);
Chelsea.addElement(Phillips);
Chelsea.addElement(ACole);
Chelsea.addElement(Terry);
Chelsea.addElement(Cech);
ManU.addElement(Rooney);
ManU.addElement(Tevez);
ManU.addElement(Giggs);
ManU.addElement(Ronaldo);
ManU.addElement(Ferdinand);
ManU.addElement(Brown);
ManU.addElement(Sar);
teams.addElement(Arsenal);
teams.addElement(Chelsea);
teams.addElement(ManU);
// --------------- FIRST TEAM - CAPTAIN SELECTION ----------------
java.awt.List playerList1 = new java.awt.List(5);
// CREATES A BOX WITH A LIST OF TEAMS (it can view 5 before needing a scroll bar)
// (full specification needed when declaring -
// java confused with List in 'awt', and list in 'util'.
if (t_chosen1.equals("Arsenal"))
playerList1.add("Adebayor");
playerList1.add("Walcott");
playerList1.add("Fabregas");
playerList1.add("Denilson");
playerList1.add("Gallas");
playerList1.add("Eboue");
playerList1.add("Lehmann");
} // if the chosen team is Arsenal, display chosen teams to be Arsenal players
else if (t_chosen1.equals("Chelsea"))
playerList1.add("Lampard");
playerList1.add("Drogba");
playerList1.add("Anelka");
playerList1.add("Wright-Phillips");
playerList1.add("Cole");
playerList1.add("Terry");
playerList1.add("Cech");
} // if the chosen team is Chelsea, display chosen teams to be Chelsea players
else if (t_chosen1.equals("Manchester United"))
playerList1.add("Ronaldo");
playerList1.add("Rooney");
playerList1.add("Tevez");
playerList1.add("Giggs");
playerList1.add("Ferdinand");
playerList1.add("Brown");
playerList1.add("Sar");
} // ditto
add(playerList1);
playerList1.addItemListener(new p_list_Listener1(playerList1));
// add itemListener to 'playerList' object
// - pass playerList object to listener to use getSelected() method
playerinfo1 = new TextArea(10, 38);
add(playerinfo1);
// --------------- SECOND TEAM - CAPTAIN SELECTION ---------------- - same as above, for team2
java.awt.List playerList2 = new java.awt.List(5); // CREATES A BOX WITH A LIST OF TEAMS (it can view 5 before needing a scroll bar)
// add "Adebayor" as a selectable Captain for the Arsenal team
if (t_chosen2.equals("Arsenal"))
playerList2.add("Adebayor");
playerList2.add("Walcott");
playerList2.add("Fabregas");
playerList2.add("Denilson");
playerList2.add("Gallas");
playerList2.add("Eboue");
playerList2.add("Lehmann");
// add "Lampard" as a selectable Captain for the Chelsea team
else if (t_chosen2.equals("Chelsea"))
playerList2.add("Lampard");
playerList2.add("Drogba");
playerList2.add("Anelka");
playerList2.add("Wright-Phillips");
playerList2.add("Cole");
playerList2.add("Terry");
playerList2.add("Cech");
// add "Christiano Ronaldo" as a selectable Captain for the Manchester United team
else if (t_chosen2.equals("Manchester United"))
playerList2.add("Ronaldo");
playerList2.add("Rooney");
playerList2.add("Tevez");
playerList2.add("Giggs");
playerList2.add("Ferdinand");
playerList2.add("Brown");
playerList2.add("Sar");
add(playerList2);
playerList2.addItemListener(new p_list_Listener2(playerList2));
playerinfo2 = new TextArea(10, 38);
add(playerinfo2);
// ------ CHOICE MENU & TEXTFIELD - CHOOSE PLAYER TO SHOW ATTRIBUTES IN TEXTFIELD - TEAM 1 ---------
Choice p_choice1 = new Choice();
// new dropdown menu - choosing which player's info to display
p_choice1.add("-- Choose player to display info --");
if (t_chosen1.equals("Arsenal"))
p_choice1.add("Emmanuel Adebayor"); //Striker
p_choice1.add("Theo Walcott"); //Striker
p_choice1.add("Cesc Fabregas"); //Mid
p_choice1.add("Denilson"); //Mid
p_choice1.add("William Gallas");//Def
p_choice1.add("Emmanuel Ebou�");//Def
p_choice1.add("Jens Lehmann");//Keeper
else if (t_chosen1.equals("Chelsea"))
p_choice1.add("Didier Drogba");//Striker
p_choice1.add("Nikolas Anelka");//Str
p_choice1.add("Frank Lampard");//Mid
p_choice1.add("Shaun Wright-Phillips");//Mid
p_choice1.add("Ashley Cole");//Def
p_choice1.add("John Terry");//Def
p_choice1.add("Petr Cech");//Keeper
else if (t_chosen1.equals("Manchester United"))
p_choice1.add("Wayne Rooney");//Str
p_choice1.add("Carlos T�vez");//Str
p_choice1.add("Ryan Giggs");//Mid
p_choice1.add("Christiano Ronaldo");//Mid
p_choice1.add("Rio Ferdinand");//Def
p_choice1.add("Wes Brown");//Def
p_choice1.add("Edwin van der Sar");//Keeper
add(p_choice1);
TextField nameField1 = new TextField("", 30);
add(new Label("Name"));
add(nameField1);
TextField ageField1 = new TextField("", 30);
add(new Label("Age"));
add(ageField1);
TextField teamField1 = new TextField("", 30);
add(new Label("Team"));
add(teamField1);
TextField speedField1 = new TextField("", 30);
add(new Label("Speed"));
add(speedField1);
TextField defenceField1 = new TextField("", 30);
add(new Label("Defence"));
add(defenceField1);
TextField accuracyField1 = new TextField("", 30);
add(new Label("Accuracy"));
add(accuracyField1);
TextField positionField1 = new TextField("", 30);
add(new Label("Position"));
add(positionField1);
Vector fields1 = new Vector(8, 2); // PASS TO CHOICE LISTENER
fields1.add(nameField1);
fields1.add(ageField1);
fields1.add(teamField1);
fields1.add(speedField1);
fields1.add(defenceField1);
fields1.add(accuracyField1);
fields1.add(positionField1);
p_choice1.addItemListener(new ChoiceListener(fields1, teams, p_choice1, t_chosen1));
// pass the teams vector to variable, to:
// 1) create players
// 2) call methods to show their different attributes in each field
// ------- CHOICE MENU & TEXTFIELD - CHOOSE PLAYER TO SHOW ATTRIBUTES IN TEXTFIELD - TEAM 2 ---------
Choice p_choice2 = new Choice();
p_choice2.add("-- Choose player to display info --");
if (t_chosen2.equals("Arsenal"))
p_choice2.add("Emmanuel Adebayor"); //Striker
p_choice2.add("Theo Walcott"); //Striker
p_choice2.add("Cesc Fabregas"); //Mid
p_choice2.add("Denilson"); //Mid
p_choice2.add("William Gallas");//Def
p_choice2.add("Emmanuel Ebou�");//Def
p_choice2.add("Jens Lehmann");//Keeper
else if (t_chosen2.equals("Chelsea"))
p_choice2.add("Didier Drogba");//Striker
p_choice2.add("Nikolas Anelka");//Str
p_choice2.add("Frank Lampard");//Mid
p_choice2.add("Shaun Wright-Phillips");//Mid
p_choice2.add("Ashley Cole");//Def
p_choice2.add("John Terry");//Def
p_choice2.add("Petr Cech");//Keeper
else if (t_chosen2.equals("Manchester United"))
p_choice2.add("Wayne Rooney");//Str
p_choice2.add("Carlos T�vez");//Str
p_choice2.add("Ryan Giggs");//Mid
p_choice2.add("Christiano Ronaldo");//Mid
p_choice2.add("Rio Ferdinand");//Def
p_choice2.add("Wes Brown");//Def
p_choice2.add("Edwin van der Sar");//Keeper
add(p_choice2);
TextField nameField2 = new TextField("", 30);
// nameField1.setText("Here, you store the name");
add(new Label("Name"));
add(nameField2);
TextField ageField2 = new TextField("", 30);
add(new Label("Age"));
add(ageField2);
TextField teamField2 = new TextField("", 30);
add(new Label("Team"));
add(teamField2);
TextField speedField2 = new TextField("", 30);
add(new Label("Speed"));
add(speedField2);
TextField defenceField2 = new TextField("", 30);
add(new Label("Defence"));
add(defenceField2);
TextField accuracyField2 = new TextField("", 30);
add(new Label("Accuracy"));
add(accuracyField2);
TextField positionField2 = new TextField("", 30);
add(new Label("Position"));
add(positionField2);
Vector fields2 = new Vector(8, 2); // PASS TO CHOICE LISTENER
fields2.add(nameField2);
fields2.add(ageField2);
fields2.add(teamField2);
fields2.add(speedField2);
fields2.add(defenceField2);
fields2.add(accuracyField2);
fields2.add(positionField2);
p_choice2.addItemListener(new ChoiceListener(fields2, teams, p_choice2, t_chosen2));
// pass the teams vector to variable, to:
// 1) create players
// 2) call methods to show their different attributes in each field
// --------------- add START GAME button ----------------
Button c = new Button("Start Game");
add(c);
c.addActionListener(new startgameListener(teams));
// --------------- WINDOW CLOSER LISTENER ----------------
addWindowListener(new WindowCloser()); // no object relation - you are adding a listener to the FRAME
// --------------------- p_list_listener1 - listener for playerList1 ------------------
class p_list_Listener1 implements ItemListener
java.awt.List playerslist;
public p_list_Listener1(java.awt.List playerslist)
this.playerslist = playerslist;
public void itemStateChanged(ItemEvent evt)
String sth = playerslist.getSelectedItem();
// ----------- PLAYER BIO'S ------------ //
// ---- ARSENAL:
String adebayorBio = "Emmanuel Adebayor (born 26 February 1984 in Lom�) is \na Togolese " +
"football player of Nigerian descent who \ncurrently plays for Arsenal.";
String walcottBio = "Theo James Walcott (born 16 March 1989 in \nStanmore, London) is an " +
"English footballer of Caribbean \ndescent renowned for his pace, who " +
"currently plays for \nArsenal, having signed there from Southampton on" +
" 20 January 2006.";
String fabregasBio = "Francesc Cesc F�bregas Soler (born 4 May 1987 in Arenys \nde Mar, " +
"Catalonia, Spain) is a Spanish footballer \nwho plays as a central " +
"midfielder for Arsenal in the \nEnglish Premier League and for the" +
" Spanish national team.";
String denilsonBio = "Den�lson Pereira Neves, known as Den�lson (born on \nFebruary 16, 1988 " +
"in S�o Paulo, Brazil) is a Brazilian \nfootballer who usually plays as" +
" a midfielder. He plays for English \nside Arsenal and is currently the" +
" captain of \nthe Brazil under-20 national team.";
String gallasBio = "William Gallas, (born 17 August 1977 in Asni�res-sur-Seine), \nis a French" +
" international footballer of Guadeloupian \ndescent who currently plays for " +
"and captains \nArsenal in the English Premier League.";
String eboueBio = "Emmanuel Ebou� (born June 4, 1983 in Abidjan, C�te d'Ivoire) \nis an Ivorian " +
"football player who currently plays for \nArsenal.";
String lehmannBio = "Jens Lehmann (German, born November 10, 1969 in Essen) is an award-winning German football goalkeeper who plays for Arsenal and for the German national team. He was voted Best European Goalkeeper twice in his career, and he has been selected for three World Cup squads.";
// ---- CHELSEA:
String lampardBio = "Frank James Lampard, Jr. (born 20 June 1978) is an \nEnglish football " +
"player currently at Chelsea and \npreviously with West Ham United and Swansea City.";
String drogbaBio = "Didier Yves Drogba T�bily (born March 11, 1978 in Abidjan, C�te d'Ivoire) is a footballer from C�te d'Ivoire who currently plays for Chelsea in the English Premier League.";
String anelkaBio = "Nicolas Anelka (born March 14, 1979 in Versailles, France) is a French footballer who plays in the forward position.";
String phillipsBio = "Shaun Cameron Wright-Phillips (born 25 October 1981 in Greenwich, London) is an English football player of Jamaican and Grenadian descent.";
String coleBio = "Ashley Cole (born 20 December 1980, Stepney, London) is an English footballer of Barbadian descent. Cole plays left back for Chelsea and for the England national team.";
String terryBio = "John George Terry (born December 7, 1980 in Barking, London) is an English professional footballer. Terry plays as a centre back and is the captain of Chelsea in the English Premier League and officially for the England national football team.";
String cechBio = "Petr Cech (born 20 May 1982 in Plze?, Czechoslovakia, now Czech Republic) is a Czech international football goalkeeper who is currently contracted to English Premier League football club Chelsea F.C., for whom he has played since July 2004.";
// ---- MANU:
String ronaldoBio = "Cristiano Ronaldo dos Santos Aveiro, OIH (pronounced \n[k?i??ti?nu ?u?na?du])," +
"(born 5 February 1985 in Funchal, \nMadeira), better known as Cristiano Ronaldo, is a " +
"\nPortuguese professional footballer. He plays both for \nthe English Premier League club " +
"Manchester United and \nthe Portuguese national team.";
String rooneyBio = "Wayne Mark Rooney (born 24 October 1985 in Liverpool, Merseyside) is an English footballer who currently plays for the English Premier League club Manchester United and the England national team.";
String tevezBio = "Carlos Alberto T�vez (born on 5 February 1984 in Ciudadela, Buenos Aires) is an Argentine footballer who currently plays for Premier League club Manchester United. He was described by Diego Maradona as the 'Argentine prophet for the 21st century.'";
String giggsBio = "Ryan Joseph Giggs OBE[1] (born Ryan Joseph Wilson on 29 November 1973 in Ely, Cardiff) is a Welsh footballer currently playing for Manchester United in the English Premiership, and formerly for the Welsh national team prior to his retirement from international football on 2 June 2007.";
String ferdinandBio = "Rio Gavin Ferdinand (born 7 November 1978 in Peckham, London) is an English footballer of mixed St Lucian,and Anglo-Irish descent. He plays at centre-back for Manchester United in the Premier League and at the international level for the England national football team.";
String brownBio = "Wes 'Baked Bean' Michael Brown (born 13 October 1979 in Longsight, Manchester) is an English football player who plays as a defender for Manchester United.";
String sarBio = "Edwin van der Sar (born 29 October 1970 in Voorhout) is a Dutch professional footballer who plays as a goalkeeper. He is captain of the Dutch national team and plays club football for Manchester United in the English Premier League.";
// --------- TEAM BIO'S DONE!!!!!! ---------- //
try
if (sth.equals("Adebayor")) // if the user selects "Arsenal", show Arsenal's Bio
playerinfo1.setText(adebayorBio);
playerinfo1.setEditable(false);
//t_chosen = sth;
else if (sth.equals("Walcott")) // if the user selects "Arsenal", show Arsenal's Bio
playerinfo1.setText(walcottBio);
playerinfo1.setEditable(false);
//t_chosen = sth;
else if (sth.equals("Fabregas")) // if the user selects "Arsenal", show Arsenal's Bio
playerinfo1.setText(fabregasBio);
playerinfo1.setEditable(false);
//t_chosen = sth;
else if (sth.equals("Denilson")) // if the user selects "Arsenal", show Arsenal's Bio
playerinfo1.setText(denilsonBio);
playerinfo1.setEditable(false);
//t_chosen = sth;
else if (sth.equals("Gallas")) // if the user selects "Arsenal", show Arsenal's Bio
playerinfo1.setText(gallasBio);
playerinfo1.setEditable(false);
//t_chosen = sth;
else if (sth.equals("Eboue")) // if the user selects "Arsenal", show Arsenal's Bio
playerinfo1.setText(eboueBio);
playerinfo1.setEditable(false);
//t_chosen = sth;
else if (sth.equals("Lehmann")) // if the user selects "Arsenal", show Arsenal's Bio
playerinfo1.setText(lehmannBio);
playerinfo1.setEditable(false);
//t_chosen = sth;
// if CHELSEA TEAMS
else if (sth.equals("Lampard")) // if the user selects "Chelsea", show Chelsea's Bio
playerinfo1.setText("" + lampardBio);
playerinfo1.setEditable(false);
//t_chosen = sth;
else if (sth.equals("Drogba")) // if the user selects "Arsenal", show Arsenal's Bio
playerinfo1.setText(drogbaBio);
playerinfo1.setEditable(false);
//t_chosen = sth;
else if (sth.equals("Anelka")) // if the user selects "Arsenal", show Arsenal's Bio
playerinfo1.setText(anelkaBio);
playerinfo1.setEditable(false);
//t_chosen = sth;
else if (sth.equals("Wright-Phillips")) // if the user selects "Arsenal", show Arsenal's Bio
playerinfo1.setText(phillipsBio);
playerinfo1.setEditable(false);
//t_chosen = sth;
else if (sth.equals("Cole")) // if the user selects "Arsenal", show Arsenal's Bio
playerinfo1.setText(coleBio);
playerinfo1.setEditable(false);
//t_chosen = sth;
else if (sth.equals("Terry")) // if the user selects "Arsenal", show Arsenal's Bio
playerinfo1.setText(terryBio);
playerinfo1.setEditable(false);
//t_chosen = sth;
else if (sth.equals("Cech")) // if the user selects "Arsenal", show Arsenal's Bio
playerinfo1.setText(cechBio);
playerinfo1.setEditable(false);
//t_chosen = sth;
// if MANU teams
else if (sth.equals("Ronaldo")) // .... and so on and so forth
playerinfo1.setText("" + ronaldoBio);
playerinfo1.setEditable(false);
else if (sth.equals("Rooney")) // if the user selects "Arsenal", show Arsenal's Bio
playerinfo1.setText(rooneyBio);
playerinfo1.setEditable(false);
//t_chosen = sth;
else if (sth.equals("Tevez")) // if the user selects "Arsenal", show Arsenal's Bio
playerinfo1.setText(tevezBio);
playerinfo1.setEditable(false);
//t_chosen = sth;
else if (sth.equals("Giggs")) // if the user selects "Arsenal", show Arsenal's Bio
playerinfo1.setText(giggsBio);
playerinfo1.setEditable(false);
//t_chosen = sth;
else if (sth.equals("Ferdinand")) // if the user selects "Arsenal", show Arsenal's Bio
playerinfo1.setText(ferdinandBio);
playerinfo1.setEditable(false);
//t_chosen = sth;
else if (sth.equals("Brown")) // if the user selects "Arsenal", show Arsenal's Bio
playerinfo1.setText(brownBio);
playerinfo1.setEditable(false);
//t_chosen = sth;
else if (sth.equals("Sar")) // if the user selects "Arsenal", show Arsenal's Bio
playerinfo1.setText(sarBio);
playerinfo1.setEditable(false);
//t_chosen = sth;
catch (NullPointerException e)
// if sth equals 'null', catch the exception and continue the program
} // end class
// --------------- p_list_Listener2 - listener for playerList2 ------------------
class p_list_Listener2 implements ItemListener
java.awt.List playerslist;
public p_list_Listener2(java.awt.List playerslist)
this.playerslist = playerslist;
public void itemStateChanged(ItemEvent evt)
String sth = playerslist.getSelectedItem();
// ----------- PLAYER BIO'S ------------Ok. Here's my code at last. It comprises of three classes, each creating three different frames:
Class 1:
import java.awt.*;
import java.awt.event.*;
import javax.swing.*;
import java.util.Vector;
class class1
public static void main(String[] param)
Frame f = new TestFrame("test");
f.setSize(600, 450);
f.setVisible(true); // the first window is shown
class TestFrame extends Frame
public TestFrame(String title)
super(title);
setLayout(new FlowLayout());
Button a = new Button("Click Me");
add(a);
a.addActionListener(new ButtonListener());
addWindowListener(new WindowCloser());
class ButtonListener implements ActionListener
public void actionPerformed(ActionEvent evt)
class2 c_instance = new class2();
c_instance.mainfalse();
Class 2:
import java.awt.*;
import java.awt.event.*;
import javax.swing.*;
import java.util.*;
import java.util.Vector;
import javax.swing.BoxLayout;
public class class2
Vector teams;
Vector Arsenal = new Vector(4);
Player Adebayor = new Striker();
Player Walcott = new Striker();
Player Fabregas = new Midfielder();
Player Denilson = new Midfielder();
Player Gallas = new Defender();
Player Eboue = new Defender();
Player Lehmann = new Goalkeeper();
// ONLY CREATING ONE TEAM FOR THE PURPOSE OF THE SIMPLIFIED PROGRAM
public void mainfalse()
Frame m_frame = new mainframe("class3", teams);
m_frame.setSize(1200, 700);
m_frame.setVisible(true);
class mainframe extends Frame
Vector teams;
public mainframe(String title, Vector teams)
super(title);
this.teams = teams;
setLayout(new FlowLayout());
Arsenal.addElement(Adebayor);
Arsenal.addElement(Walcott);
Arsenal.addElement(Fabregas);
Arsenal.addElement(Denilson);
Arsenal.addElement(Gallas);
Arsenal.addElement(Eboue);
Arsenal.addElement(Lehmann);
teams.addElement(Arsenal);
// --------------- add START GAME button ----------------
Button c = new Button("Start Game");
add(c);
c.addActionListener(new startgameListener(teams));
// --------------- WINDOW CLOSER LISTENER ----------------
addWindowListener(new WindowCloser());
class startgameListener implements ActionListener
Vector teams;
public startgameListener(Vector t1)
this.teams = t1;
public void actionPerformed(ActionEvent evt)
class3 c_instance1 = new class3();
c_instance1.gVector(teams);
}*... and Class 3:*
import java.awt.*;
import java.awt.event.*;
import javax.swing.*;
import java.util.Vector;
public class class3
Vector teams;
public void gVector(Vector t1)
this.teams = t1;
Frame main = new mainframe("Main Window", teams);
main.setSize(1400, 900);
main.setVisible(true);
class mainframe extends Frame
public mainframe(String title, Vector t1)
super(title);
setLayout(new FlowLayout());
addWindowListener(new WindowCloser());
Vector teams = t1;
JOptionPane.showMessageDialog(null, "Hello and WELCOME to The FIRST, annual StickMan Footy!");
if (teams.contains(Arsenal))
int t = teams.indexOf(Arsenal);
Vector Arsenal = (Vector) teams.elementAt(t);
// getName() is a method declared in the Player class
// the Player class is the superclass of the Striker class
/* if (teams.contains(Adebayor))
And my error message after trying to compile Class 2, is "cannot find symbol - variable Arsenal".
........... help.
Shax -
Cannot find boot record of WD Raptor on KT4
Hello forum, this is my first post.
I have been searching Google for a solution of my problem and found this forum. However, after searching this forum and reading quite a few threads I still could not find the solution. Here's my problem:
I have a brand new WD Raptor 74 GB connected to serial 1 as a single drive. The mainboard is KT4 Ultra BSR. I have built an array by pressing ctrl-f at bootup. The only option was stripe and I have set the array (array 1) as bootable. I went into BIOS and set the array as first in boot order. Conclusion, the BIOS seems to detect my array and so far so good.
I booted Win XP installation CD and pressed F6 to install the Promise drivers. I used the newest drivers which were downloaded from MSI yesterday. Installation detected my array so I created a new partition, formatted it and the installation program copied files to that partition. When copying was finished, the computer had to be restarted and it was supposed to boot from my harddrive where it copied the files. Now to the point of my problem: BIOS has detected my array and tried to boot, but it says that boot record could not be found! I don't know whether Windows installation has failed to create a boot record or BIOS could not detect the boot record.
I have checked the contents of C: by booting Win XP installation CD and gone into recovery mode. I would access C: and found the common files used for Windows bootup: boot.ini, ntldr, etc.
So the required files are in place, but either the boot record does not exist or BIOS cannot find it. I wonder if anyone could give me any suggestion about how to solve this problem. I want to make my SATA drive bootable.
Thanks in advanceQuote
Originally posted by Wonkanoby
have you removed any other form of storage drives
ive evan seen xp write the mbr to a card reader rather than the target raid drive
I have a DVD and DVD-RW connected to IDE2. I had a Hitachi HDD connected to IDE1, but it was removed before I ran Windows installation. The reason is because I want my SATA drive to have C: while having a HDD connected would mean the partions on that drive would occupy the C and D partition letters. I planned to attach the Hitachi after Windows installation has completed. BIOS has no problem detected my array, but when trying to boot from the array, the boot record cannot be found eventhough I have run the Windows installation which I thought would create the MBR automatically.
Is there any way to make my array bootable? It has been boot-enabled in the SATA settings.
Maybe you are looking for
-
Is there a way to have iCloud NOT sync rules in Mountain Lion Mail?
My wife and I each have our own MacBook Pro on Mountain Lion and we share an iPad on iOS 6. We use OS X Mail as our mail client for our accounts on our ISP mail service. We have iCloud enabled on all three devices but we have Mail disabled on all th
-
Photos not uploading to iCloud photo library from PC
Hopefully I am not the only person with this problem, but it's driving me round the bend. iCloud installed on PC and default folder Pictures\iCloud Photos\My Photo Stream contains c1,800 photos When I got to Favourites\iCloud Photos\My Photostream th
-
date and time hang up on apple tv
-
Hi, I am not able to view the shipping tab in PO while creating a Inter company stock transfer order. Can U guys let me know what r the possible reasons behind the shipping tab not appearing in PO. thanks in advance
-
Access to UI elements in onAction method
Hi everbody, I have a really simple question: how can I access UI elements of a view in onAction methods so that I can change their attributes? (In the wdModifyView method I had no problem because I got access by the IWDView parameter). Regards, Chri