K8T Neo-FIS2R, can't install XP onto SATA HDD

Hi all --
I've been Googling and searching this forum for a while but can't find the same problem as what I'm having. Can anyone help?
Note that I'm using Windows XP Pro (32-bit), a single (not RAID) 80GB SATA HDD.
I'm builing my first computer. POST is fine. Then I tried booting from my WinXP floppies (my CD isn't bootable). When asked, I hit F6 so that I can install the SATA drivers. Putting in the "VIA VT64520 or VT8237 chip driver version 5.1.2600.220" disk doesn't work (can't find the drivers), but the Windows Installer CAN find drivers on the "G72-PRSA060 Promise 376/378 Driver" disk, so I load up those.
After the 6th and final floppy, it says "Setup did not find any hard disk drives installed in your computer."
First thought: I forgot to partition! So I went into fdisk (using a Windows ME boot disk from http://www.bootdisk.com), partitioned it all up into drives C through I, and tried the above steps again. Same problem.
Second thought: I forgot to format! So I typed "format c:" and "format d:" (again, using the WinMe bootdisk), so they are now FAT32 drives. (I'm eventually going to want NTFS, but presumably I'll get to do that from within Windows.) Tried the above steps again -> same problem.
Third thought: Perhaps I should update the BIOS. So I flashed the BIOS, from v.1.4 to v.1.7. Still boots fine, but didn't solve the problem.
Fourth thought: Try different serial ATA ports. But I can't seem to get it to work in either SATA1, SER-1, or even SATA2 (which oddly shows up as SATA0 when I press at startup).
Also, when looking in the Boot Order in the BIOS, I note that I can only see my HDD listed (WD80GB...) when it's plugged into the VIA controller (SATA1&2) not the Promise controller (SER-1&2). And in either case the entry is prefixed with "(RAID)". Should this be worrysome?
I'm happy to post additional details, I'm just not sure what else you need to know. Any thoughts?
Many thanks in advance for your help!

Update:
I burned a BOOTABLE CD using the CDImage program available here:
http://unattended.msfn.org/xp/finish.htm
I then made sure that the SATA cord was plugged into SER-1 (i.e. on the Promise controller).
Booted from CD-ROM, pressed F6, added the Promise controller driver (from the included floppy), but NOT the FastTrak RAID controller.
It worked! Life is good!
Just wanted to let you all know, and extend my hearty thanks!
P.S. Since my C: and D: drivers were already FAT32 (from when I was fiddling around and used format c: and format d:), I wanted to make them NTFS. During the Windows install, after saying that I wanted to install to the C: drive, I chose the option to Format (NOT quick format) this drive as NTFS. Once Windows was successfully installed, I went into Control Panel -> Admin Tools and reformatted the D: drive as NTFS as well. So all that worked just fine.

Similar Messages

K8T NEO FIS2R can't use the RAID controller....

I have this very strange issue.
As soon as I connect a harddisk to the Promise (378) controller of this board and assign it to an array, the system doesn't work like it should.
Symptoms:
- MS Windiag (a memory testing application) reports thousands of errors
- Memtestx86 causes a spontaneous reset within seconds
- I can try to install Windows, but the process never completes; during the installation everything works really really slow (partial XP installation takes over 2 hours!)
- Linux gives me a kernel panic while booting
My system specs:
- MSI K8T Neo FIS2R (bios 1.5)
- Athlon 3000+
- 2x 512MB PQI memory (tested with GEIL/Kingston/Infineon memory as well, the problem persists!)
- Radeon 9700
- Levicom PSU (34A RMS on 12V line) (also tried Enermax 460W and Antec tru power 480W)
- 2x WD Raptor 36Gb (RAID 0 array 1)
- 2x Maxtor Diamond plus (RAID 0 array 2)
- 4x optical drive
I just can't figure out what's going on here... if I don't use the onboard RAID controller everything is fine.... but I need it for my two arrays... (besides that, it should work, shouldn't it?).
Is this perhaps just a bug in the BIOS of my system? If so... MSI please resolve this issue, my computer is worthless for the time being.. :(

Quote
Originally posted by Bas
Try this version of Memtest86.
YAY! This memory tester seems to work correctly..!
If I put a single module (PQI memory) in DDR slot 1 I get loads of errors. In slot 2 and 3 they work just fine. When combining two modules, using slot 2 and 3, I still get some errors (32, all above 1000Mb)... but it's the best I can get out of my 1Gb.
Is it safe to assume that this is a compatbility issue that can be fixxed by buying some supported memory?

K8T Neo-FIS2R Old Problem, New Issue

I made my system back in 2003 using a K8T Neo-FIS2R motherboard and a Barracuda 7200 SATA 160GB drive (ST3160023AS). If you don't remember, back then motherboards that supported SATA drives for main drives, sometimes needed extra drivers in order for the windows installation process to work. At first this threw me, but since then I have reformatted my drive a few times using the same disk with no issues.
5 years of file sharing can do a number on your harddrives, and it seems my Barracuda has finally died. It came time to replace my drive with a Western Digital Caviar 320GB drive SE16 (WD3200AAKS). I did not predict there would be any issue with replacing my SATA drive. I have another 500GB drive connected to my system used for only storage and the computer recognized it at once.
So I formatted my WD HD, to NTFS and made it active. Then I installed it in my computer disconnecting my other 500GB drive. I ran windows installation with my Windows CD (which I have used many times and I keep it in pristine condition).
I found that after I hit F6, and it gave me a selection of SATA drivers to use (used xp), it did not not see that drive was there when asking which drive to format (I repeated this many times). I set about making a new SATA boot disk thinking that my pre-used one had gone bad.
http://global.msi.com.tw/index.php?func=downloaddetail&type=driver&maincat_no=1&prod_no=565
VIA VT8237(R) SATA RAID Driver (For floppy driver)
I followed the disk directions having already done it before. When I tried to install with my new drivers, I got this error.
"File\I386\NT5\viamraid.sys caused an unexpected error (4096) at line 2108 in d:\xpclient\base\boot\setup\oemdisk.c."
Now i KNOW my windows instillation CD is good, but just in case I used another windows CD and got the same error.
The only idea I can come up with is that I upgraded the bios to much and now it is having issues. My bios version is:
AMIBIOS A6702VMS V2.2 030405
SATA378 TX2plus(tm) Bios Version 1.00.103026
Does anyone have any ideas of what I can try? I have done all the easy stuff I could think off like try different cables, and plug in my SATA to the second sata port and not the first. I have run out of ideas.
The only list thing I could try was connecting my sata drive to the computer using a SATA to USB adapter, and finding the partition in windows through that way. For some weird reason windows will see USBs in the computer but not installed Sata drives. I am thinking I will install windows using the USB device and then try plugging in the drive directly. I have no idea if it will work.
Any help would be greatly appreciated.
Sombrenote

Quote from: sombernote on 11-July-08, 09:15:36
Thank you so much for your help.
I tried your two versions of your drivers, "VIA PIDE&SATA RAID.rar" "Promise 20378 S-ATA RAID.rar" neither of them worked well (I selected the "VIA RAID Controller(Windows XP"). I received a slightly different version of the last error "File\I386\NT5\viamraid.sys caused an unexpected error (4096) at line 2108 in d:\xpclient\base\boot\setup\oemdisk.c."
The (4096) was a different number.
I had used 4 different (yet old) disks, trying to get it to work. None of them did so until i tried it once more. This last time worked, it saw and used the drivers. I was able to get into the disk selection screen, and set to format the disk. As it started formatting (Quick), windows said that there was something wrong with the "Disk or CD". It then asked for me to install the SATA combo drivers. I let it detect the drivers I was using, and it kept saying something was wrong. I tried it 3 more times, and the last time it held and copied the files from the CD, to start windows.
It is obvious to me that I have either a bad disk, CD, Disk drive, or CD drive. This is quite possiblly my last format before I make my new computer. Thank you very much for your help. I would have had to start my voodoo magic tricks to get it to work.
Crappy floppy cause that
Happend to me many times as well, when you receive the error take out diskette and re-insert it, then load drivers again until works.
Of course simple solution is just replace the floppy drive to avoid "voodoo magic tricks"
Or best solution do a slipstream XP installation and integrate the drivers which you need in XP installation.
>>> Slipstreaming Windows XP Service Pack 2 and Create Bootable CD<<<
>>> Slipstreamed Windows XP CD Using SP2<<<
"Thank you very much for your help. I would have had to start my voodoo magic tricks to get it to work."
You are done well

Help! XP install problems with K8T Neo-FIS2R

The other day I put together a new system for a friend. I got the system to POST properly, the diagnostic lights on the D bracket are fine, and I can edit the BIOS, and the BIOS sees all the drives properly.
However, installing XP Pro has been impossible. I set the system to boot first to the CD, then to the hard drive (from the BIOS). After booting to the CD, I never see the message I am used to seeing ("Press any key to boot from CD...) when booting from the XP Pro install disk. The system thinks about things for a long time with a blank screen, then later it finally begins to do the install. Things appear normal at this point as in any other time I have installed XP Pro. I reformat the hard drive to start clean and then the XP install files are copied over. I get the standard message that the system will reboot and this is where things get flaky. The system reboots, but I never get the message once again on whether or not to boot from the CD. So after a while the system tries to install XP once again (it would repeat this process forever....trust me). I've popped the CD out right after the system reboots so it will try to go to the hard drive. I just get some kind of boot failure message and to insert the bootable media or whatever. I've even gone into the BIOS right after the reboot to switch the BIOS loading to try and load the hard drive first. This still doesn't give me the desired results.
This is by far the weirdest thing I've ever experienced when doing an install. I've installed XP Pro on at least 15-20 desktops/laptops of different configs and never ran into this before.
The BIOS settings are stock. I didn't see anything in there that was really needed tweaking or that hadn't "set itself". I haven't messed with the SATA or RAID stuff since it's not really necessary in this situation.
Here are the system specs:
--Antec 430 True Power PSU
--K8T Neo-FIS2R mobo
--AMD 3000+ 64 bit CPU
--40GB Maxtor HD (master on IDE1)
--Lite-On DVD-ROM drive (slave on IDE1)
--80GB Western Digital (8MB buffer) (master on IDE2)
--Sony DRU510A DVD-RW (slave on IDE2)
--(2) Kingmax 184 Pin 512MB DDR PC-3200 Model# MPXC22D-38
--ATI 9800 Pro
--3.5 Floppy
All the components except the mobo, CPU, and memory are from another AMD system that was running fine. No problems with any of the HD's or the optical drives. All new components were purchased from newegg.
I thought that maybe I had a problem with the jumpering of the drives so I messed with those in about every possible combination. I took IDE2 completely out of the system and just tried to get it running with the 40GB Maxtor and the Lite-On drive. I tried about every master/slave/cable select combination but nothing was working. In certain combinations the BIOS recognized everything as I intended. I've pulled everything off that doesn't need to be connected. Keyboard, monitor, and internal components are the only things connected.
I don't consider myself to be a guru at this business, but I can get through most things with enough trial and error. This really has me stumped.
Any help is certainly appreciated.
Thanks,
Heath

Quote
Originally posted by chasmon
Hi all,
I have just setup up a brand new system but am having probelms getting it working. I want to install XP on a single Maxtor 160Gb drive.
I have my HD on Promise Ser1 and all SATA stuff in BIOS enabled. When I get to the screen I press F6 and then when promted I insert the floppy with the promise drivers on. I then get this message:
"File txtsetup.oem caused an unexpected error (4096) at line 1742 in d:\xpclient\base\boot\setup\oemdisk.c"
I can't get past this screen I have tried:
1.Drivers from the CD supplied.
2.Drivers from the MSI website.
Please help me this lot cost lots of hard earned I'm pretty gutted at the moment.
System:
Antec 380W PSU and Sonata Case
LG DVDROM 8163B
NEC DVDR/RW 2500B
Panasonic Floppy
Neo FIS2R mobo
Maxtor Diamondmax Plus 9 160Gb SATA150
Benq RF K/B & Mouse
Download the drivers from MSI again, and when you copy the contents of the XP folder to floppy ADD the file txtsetup.oem from the directory above that folder. Worked for me..!
Ian

K8t neo fis2r - core center not functional after installing sound card

Hi. I had been using Core Center with Dynamic Overclocking enabled and all was well. When idle, my amd64 3000+ (2.0ghz), was running at 800mhz. Under load it would go up to 2100mhz. But yesterday, I installed an Auzentech x-plosion sound card and after i installed the driver, the dynamic overclocking stopped working, my cpu is running at max all the time. (The variable fan speed function still works).
I checked the IRQ and there is no conflict, I uninstalled the amd64 driver and core center and reinstalled. Still does not work. I uninstalled the auzentech driver, rebooted, and cancelled new hardware wizard. Then the variable cpu frequency feature worked. Once I install the driver for the auzentech, dynamic oc stops working. I was thinking to try another pci slot but it appears to be a software issue rather than a hardware issue. The new version of Core Center does not work with my board even though msi says it's compatible so I'm still using the one that always worked. The amd driver is the latest and also always worked.
Has anyone else had a similar problem, perhaps using the auzentech sound card with this board and Core Center? Or does anyone have any suggestions?
Thanks!
K8T Neo FIS2R
AMD64 3200
AMI bios version 2.2
1.5Gb pc3200 memory
nvidia quadro FX 1100 128mb AGP
Antec 430W ps

Hey guys, I just went to AMDs site to get the dashboard utility mentioned and in the readme, it stated that in XP, the power option needs to be set to portable/laptop. But in the past, I read that it needed to be set to "always on" and that it is, in fact, what I had it set to before when cool n quiet was working. Now I change it to "portable/laptop" and it works and set to "always on" doesn't work anymore. So now Core Center reports I'm at 33c @800mhz at no load. I don't get it??? I'll have to try an alternate utility just to verify that is indeed working.
btw, QV, I checked system properties, (right-click my computer > properties, or "system" in control panel) and on the "general" tab, it indicates an AMD64 3000+, 2.0GHz. But I'm pretty certain the clock frequency is dropping now as reported by core center because of the decrease in the cpu temp at idle. Am I looking in the right place in XP? I have XP pro, SP2
Again, thanks for the input and Happy New Year

Msi k8t neo fis2r xp install problem

I tried to install xp on my sata drive..i downloaded the raid drivers and put them on a floppy, it accepts the raid drivers (im not trying to use raid, just regular sata), and i select the hard drive and attempt to install to it, but the files from my xp cd keep saying something about invalid image has been installed to your hard disk (or a similar message to that)
also part of the time the comp will not boot properly, it will just beep on and hang and nothing will show to the monitor, or if i have a disc in my cdrom when i try to turn it on it wont turn on, but then when i take out the disc and reboot the comp it turns on again..no clue what might be going on..
my specs are
a64 3000+
512 mushkin special 2-2-2-5 cas 2.0 ram
80gb WD SATA 8mb cache HD
radeon 9800 pro (sapphire)
MSI K8T NEO FIS2R
sparkle 400 watt power supply

You better get something like an Enermax 465 for your rigg, as yours:
Quote
Output: [email protected]/28A,+5V@40/28.5A,[email protected],+12V@15A,[email protected],+5VSB@2A
Could blow to pieces any minute now....
15A @ 12V is way too light.....
The Enermax has 33 of them

Msi k8t neo fis2r problems part 3

sometimes when the computer is turned on it just turns the fans and leds on but doesnt boot up...
most of the time it loads up and i boot to the windows xp cd and i install the drivers for sata and then when it reaches the point of copying the files it will give me a bsod and say that there is a problem with the irql driver and then force me to shut the pc down..
sometimes it makes it past that and will begin to copy files onto the hard drive, like somehow the data is becoming corrupted..however it will start to say that the files cant copy randomly and it will allow me to retry..they will copy the 2nd time usually..i can keep hitting retry and it will usually go by..it gets to 30 something % and then crashes to bsod just giving me some random error..for some reason the files keep screwing up that go on the sata drive....I just replaced the old power supply that wasnt working with an antec true watt 430 watt power supply, so i know it isnt that..
i just cant figure out what the heck is going on..any help would be appreciated.my specs are
"IRQ NOT EQUAL OR LESS"
athlon 64 3000+ cpu
msi k8t neo fis2r motherboard
mushkin special cas 2.0 2-2-2-5 512 mb pc 3200
western digital 8mb cache 80 gb sata hard drive
sapphire radeon 9800 pro 128 mb 8x agp

fyi look an your cd sticker ity will show power, consumption, but they are way lower than you would think, hard drives,can be only 10 watts, less then some case lights , and fans, cd are similar.. your video, is the biggy somewhere between 90~150 watts..yikes .next to the cpu..and the mobo can use 50 or so (not sure about new mobos) not to mention the ram 1024 is @40 watts or so., dont forget about 25watts per pci card, not counting the sound card which can be double....
ergo the need for a big psu..
the combined total ratting on a psu is not the max number that the psu is rated, that is surge value.. so a 500 may only hold 400 sustained , and that will drop as the machine heats up, so in the end your 500 may onlyy pull 366 @50'c...

6600GT not working with K8T neo-FIS2R

I recently returned a K8T NEO-FIS2R MB for repair. The problem was that the PS/2 and USB ports were broken. However the MB has been returned and the PS/2 and USB ports work fine. I posted about this several months ago.
Now the AGP port seems to be broken (not the actual slot). I have tried a 6800 Ultra and a 6600 GT (AGP version) GFX card in this slot. Both cards fail at the driver installation point. I have tried driver versions 66.93, 67.02 and 67.03. I also tried 3 versions of the via drivers 451, 453 and 455. Even tried XP with SP1 and SP2. The PC will sometimes BSOD, reset, won't boot into windows. The drivers sometimes install then other times they won't, etc. The problems only seem to be with the drivers for the GFX cards.
The 6600 GT works as I have tried it in another MB without any problems.
I know the memory works fine as I used memtest86+ for a couple of hours on the default settings without any errors and it works in another PC.
The spec of the PC is:
XP pro
K8T NEO-FIS2R MB
512MB corsair XMS at 2.5-3-7-3
XFX 6600GT
40gig HDD
FDD
Plextor CD writer
DVD Rom
PSU is a Q-tec 550W
I know Q-tec PSUs are not up to much from what I have read elsewhere in this forum, but I have had it running in a similar system with the 6800 Ultra installed without any trouble (even with the above MB before it went faulty). I have also tried a 400W PSU, that came with the case. The Voltages on the 12V line are between 12.00 and 12.03 when using the Q-tec PSU.
Has any body else had these problems with the 6600GT in the mentioned MB.
Also, how can I check the serial number on the MB with the label on the box, as this MB that was returned to me looks to “clean” to be the one I sent away for repair.
Thanks for any help

Hey, I'm glad to see a post on the new Gforce 6600GT AGP card. I just recently put together a brand new system (see my sig for specs). System runs great. The only thing I wanted to do was replace the video card, and after a great deal of anxiety I decided the Geforce 6600GT AGP was the best bang for the buck.
Well I got home, installed the card and never get passed the bios screen. (shows your processor, memory, memory siz), the screen u hit DEL to go into the bios.
The system doens't lock up, NUM LOCK can still be turned on and off, and CAPS can be turned of and on... but thats it. Just sits on that screen. I can't go into the bios either.
what settings do I need to do prior to isntalling this card to get it to work.
Let me know if you all need anymore details to help me out.
oh, I did reset my frequency to 10x200 (which is what I think the 3000+ is supposed to be at).

MOVED: K8T Neo-FIS2R SATA and Linux Question

This topic has been moved to Operating Systems.
K8T Neo-FIS2R SATA and Linux Question

Quote
Originally posted by chasmon
Hi all,
I have just setup up a brand new system but am having probelms getting it working. I want to install XP on a single Maxtor 160Gb drive.
I have my HD on Promise Ser1 and all SATA stuff in BIOS enabled. When I get to the screen I press F6 and then when promted I insert the floppy with the promise drivers on. I then get this message:
"File txtsetup.oem caused an unexpected error (4096) at line 1742 in d:\xpclient\base\boot\setup\oemdisk.c"
I can't get past this screen I have tried:
1.Drivers from the CD supplied.
2.Drivers from the MSI website.
Please help me this lot cost lots of hard earned I'm pretty gutted at the moment. I have also tried the Via chipset with no joy.
System:
Antec 380W PSU and Sonata Case
LG DVDROM 8163B
NEC DVDR/RW 2500B
Panasonic Floppy
Neo FIS2R mobo
Maxtor Diamondmax Plus 9 160Gb SATA150
Benq RF K/B & Mouse
Don't spam man! I posted something to this same question in another thread.. from you no less! Make a new thread! lol
Hijacking = bad!
Ian

K8T Neo FIS2R AMIBOOT.ROM not working

Hi
Had a game crash on my system, and froze everything, so had to restart manualy - now I get the error BIOS is not installed..
I have downloaded a copy of the bios (not latest) and changed the relevant ROM file to AMIBOOT.ROM and copied to a freshly formated floppy.
I inserted the disk, held down CTRL and HOME and started the computer...
After a while of running through the messages of BIOS not installed and no SATA installed (which is correct), the floppy drive light comes on, and then after a while (afet I have released the CTRL and HOME keys) I get a message saying "Remove disks or other media, Press any key to restart" then nothing, if I press any key - it says the same thing untill I remove the floppy... and then it restarts again.
I have tried to restart using the floppy and the CTRL and HOME keys about 20 times so far - always the same result - I have even tried diferent versions of the BIOS.
Any ideas?
I only have one stick of RAM (256Kb - 333) and two IDE HD's
Many thanks in advance
GreenBoy

Hans
My Set up is as follows (from the top of my head as I am doing this form work)
K8T Neo FIS2R.
AMD 3300 745pin chip set.
1 stick of 512Mb ram (non branded - baught from Watford Electronics)
2 x 200Gb Maxtor HD's
1 40GB Seagate HD
1 DVD RW
Power 500W
Dont know what else you need...
Anyway - last night I reset the CMOS in the way you described.
Still cant find the VIA settings in the Advanced Chipset or elsewhare - but I will. urned of SATA in Intergrated Peripherals...
Anyway - what then happens, is it says it cannot boot.
I tried using a Win98 SE boot disk - and all the drivers were listed as not possible to load or something...
Any way - deciding I did not have anotehr boot disk to hand - tried Symantec Ghost - still same result.
Finaly I tried WinXP Pro, and found that this installed all the bootup files no problem at all - what was then found was that my C: partition was missing - yup boot sector had completely disapeared.
Anyway knowing that I have recent full backups og my primary drives using Ghost, I took the plunge, created a partition in the unalocated space, reformated the drive, and reinstalled WinXP... all seems ok for now... except the message regarding no BIOS - but from what you say as soon as I fing the switch I will loose that again.
The strange thing is I never used to get this message before, and do not remember setting anything up for SATA - couldnt afford the disks at the time....
Thanks for the help Hans, you have been more than gwenerouse with your time , but can you please give me some more information? (Im a bit of a Nooby at playing with BIOS etc as they scare the crap out of me! )
1) Why is the detail of my system so important? I have made no Hardware changes for approx 6 months and everything was fine untill the game crashed, so therefore, dont see why this should affect things.
2) Why did the flashing of the BIOS not work? I was following the instructions carefully - but nothing.. therefore in my Nooby mind this means there is something else wrong, stopping the flashing from working.
Again - many thanks
GreenBoy

K8T Neo FIS2R Won't Recognize HDDs

Here’s my situation. I am not new to building computers, but new to the AMD Athlon64, MSI boards, and SATA drives.
I purchased the K8T Neo-FIS2R (601-6702-010) main board. A single 512 MB DDR memory stick is installed. The only card installed is the ATI Radeon 7500 ALL-in-Wonder video card. I cannot get the system to recognize hard drives. I have made many changes in BIOS, but have been unsuccessful.
At first, my intention was simply to take my almost new Maxtor Diamond Max Plus 9 120 GB ATA HDD and install it with the K8T Neo motherboard. The disk has been previously formatted with Windows XP Home, and has various other programs installed. It was working fine in my older system. I put this drive (properly connected to the IDE1 on mainboard), and the K8T Neo would not recognize the drive at all. In fact, all I received were messages that SATA Raid devices were missing (apparently the Promise controller complaining). Trying to deactivate the SATA controller via bios did nothing.
Next, I decided to purchase a Seagate 160 GB Barracuda SATA HDD (ST3160023AS-RK), thinking maybe then the system would at least recognize an SATA HDD. (of course a lot of this shows my naivete’ with newer SATA standards/componets/MBoards) Initially it was recognized, and I was able to use Seagate’s software to partition the drive and format it. However, after rebooting and attempting to install Windows XP, the drive was no longer recognized by the system. On the POST screen, the VIA controller does list it as master device 1 in the SATA.
Okay, here’s what I want: I want to install the Barracuda 160 GB HDD SATA as my boot drive, and take my slightly older Maxtor HDD and make it a secondary (or slave) drive. This means a mix of SATA and ATA drives. Since MSI’s documentation both in manual and the website provides no help (that I can find) on this issue, I need suggestions on what to do. The only explanation in K8T Neo manual is to create an SATA Raid array. I do not want to do this. I simply want the SATA as boot drive, the ATA as secondary (or slave) drive, and for both of them to peacefully coexist! How do I make the mainboard recognize this?

Quote
Originally posted by saat0014
Are you getting the error when you insert the disk and it looks for the drivers on the disk? Or are you getting it at the Windows installation screen. Maybe you should try using the promise drivers and hook up your drives to the promise controller. Here's how to get the Seagate drives to work on the promise controller. Promise Scroll down to where I posted and you'll find hopefully all you need. If you need help, just ask
The error is coming at the Windows installation screen. The drivers already (seemingly) load.
I have tried installing the Promise drivers, although not as you posted in the linked thread. I only have the one SATA drive... do I still need to configure it as RAID?
I'll try this today. In all my years of building computers, I've never had as many problems as I have with this system. This is so frustrating.

MSI K8T NEO-FIS2R: RAM problems

I have the motherboard K8T NEO-FIS2R with AMIBIOS 2VMS V2.0 010505.
I tried these DDR-RAM:
DDR-RAM 512MB PC400 CL3 Kingston KVR400X64C3A/512
DDR-RAM 512MB PC400 CL3 Samsung
but the motherboard recognizes only 256 MB for both. The RAM are good: I tried them in an other pc!
Now I have installed an A-DATA ram 256 MB and the motherboard recognizes 256 MB!
Do you think that my motherboard is defective?
Thank you in advance.
P.S. I'm sorry for my bad english.

No the memory controller is onboard the CPU so in any case the MB is not defective. However the CPU revision may hold you back on some RAM especially if you mix make and model RAM on the same channel. A socket 754 CPU only has one channel so all RAM must be matched to work properly.
If those Sticks can only be seen as a wrong value when used by themselves it is likely that either they have errors or the timings in Bios are improperly set to azllow them to work. In this case you can normally find out what is going on by running memtest86. If you get errors on test 5 or 7 then you have timgs timed improperly and any other errors would show bad RAM.
Another case is not having enough power for everything to work properly together. Usually this happens when you don't have enough 12v amps for these newer rigs.
Post complete specs and test results and maybe we can help you further.

MSI K8T Neo FIS2R- Corsair Twinx XMS4000

Two weeks ago I have bought one MSI K8T Neo FIS2R with an AMD Athlon64 3200+.So far I used the computer with one DIMM of 256MB DDR PC2100 memory. This morning I have installed in the motherboard a pair of CORSAIR TWINX XMS4000 which comprises of two DIMMs of 512MB DDR 500MHz memory.
The computer did never worked again. As soon as I have turned it on, although the whole system got power the screen was blank and the motherboard did not boot. Moreover, the D-Led system of the motherboard has all its leds red which according to the manual means that the processor is probably damaged.I have never overclocked my system and before install the memory it worked perfect. I have disconnected the whole computer but the problem still exists. Can you advise me what I have to do to fix it? What is the cause of the problem? Is there any way so that I can fix it?

Quote
Originally posted by karinio
Two weeks ago I have bought one MSI K8T Neo FIS2R with an AMD Athlon64 3200+.So far I used the computer with one DIMM of 256MB DDR PC2100 memory. This morning I have installed in the motherboard a pair of CORSAIR TWINX XMS4000 which comprises of two DIMMs of 512MB DDR 500MHz memory.
The computer did never worked again. As soon as I have turned it on, although the whole system got power the screen was blank and the motherboard did not boot. Moreover, the D-Led system of the motherboard has all its leds red which according to the manual means that the processor is probably damaged.I have never overclocked my system and before install the memory it worked perfect. I have disconnected the whole computer but the problem still exists. Can you advise me what I have to do to fix it? What is the cause of the problem? Is there any way so that I can fix it?
Hi dude i had identical problem, bought i extra stick 512 400 ddr and the system wont start. Make sure your motheoard support the made of ram. In my case Asus did not support corsaire. Also it could be the slots which are damage.
bye

High frequency sound with K8T Neo-FIS2R

Hello!
I have the MSI k8t neo-fis2r mainboard with bios v 1.6 and sometimes it makes a horrible high frequency sound and I cant figure out why.
My system are:
amd 64 3000 cpu and
Corsair Value S PC3200 DDR-DIMM 512MB Unbuffered, Non-parity, 64Megx64, CL2.5
My other components does not cause the sound (that I have found out by testing).
I wonder if the ram causes the sound? Can you please help me. The sound is so bad that I cant use my computer. It only appers during heavy system load, and not in windows. It has nothing to do with my video card (because I have tried with several different cards). My bios settings are default values + cool and quit enabled. I have the core center installed so the progam controls the cpu fan.
I really hope someone can help me.

The sound does not come from the speaker and I dont think it comes fom the cpu fan either. I think it comes from the motherboard, ram or the cpu. When I dont use my mouse it is quit but when I clik it makes this sound. Can it be that I have to set all values in bios for ram etc. manually instead of automatic?
When it comes to other electrical sources I have a TV standing 0.5 meter from the computer. Could thins cause the problem? I did not have the problem with my old motherboard which was a MSI K7T Turbo2.
The sound usually appers when I am benchamarking my system. For example 3dmark 2004. Because of this I thougt there was a problem wiht my vga card but after a changed to a new one...the situation was just the same.

Booting "issues" with K8T Neo-FIS2R

Well hello everyone. First of all I want to say that my English isn't completely error-free and my problem might seem awkward because of my ways of expression.
I also want to say that i've read alot of threads and searched the forum for my problem.
For a couple of days ago I got all my parts for building my 64bit-system and I build her up. To my suprise it booted, with almost no errors. Although I could install Windows XP and use it completely, everytime I boot it (under the booting sequence) it says "Bios is not installed", although I can enter bios simply (like everyone else) just pushing the DEL-button.
But this isn't the only problem. When I enter PC Health Status it says that the cpu is running at whooping 62-65 degrees. When i have my hand around the cpu-cooler it doesn't even feel warm so I think it has something to do with my BIOS-version that i am running now (Yes, I've read that in much more threads)
Also I have problems using the Cool'n'Quiet technology. I have it supported in the BIOS and activated it although it will not work (maybe it has something to do with the bios?) With this i mean that i will not go underclocked (It's allways 2.2 GHz)
My final problem is that it sometimes takes the system 2 minutes to boot sometimes, it happend after i flashed the bios to 1.7 from 1.0
Under these circumstances I've used 1.0 AND 1.7 BIOS-versions.
I've never overclocked the computer either.
What could be wrong?
I'm using 3200+ 2.2GHz Athlon 64 cpu.
K8T Neo-FIS2R
Radeon 9800pro
Seagate 7200.7 200GB drive.
380W Antec PSU.

Quote
Originally posted by $post[username]
I've tested notebook, minial power savings and battery. C'n'q still doesn't seem to work. Yes i've enabled it in bios. I downloaded the AMD Athlon™ 64 Processor Driver for Windows XP, Version (zip) 1.1.0.14 -
Yesterday my CnQ began to work fine. I've done the same as you:
1- Enable CnQ Bios option
2- Install the AMD athlon64 driver for XP
3- Set "minimal power savings" at windows xp energy options
I have installed the CoreCenter 1.6.8.0 (is the last version) utility, and I've set enable the CnQ in this application. You'll can see that the CPU velocity change "on demmand" and the CPU fan too.
Of course, I've the last VIA 4in1 drivers, 1.7 Bios ver. etc
My temp & MHz values are:
~40ºC ~ 800 MHz idle
~50ºC ~ 2000 MHz playing or that kind of stuff
Note that the PC case is open, because the PC is under my table and there is no good ventilation.

K8T Neo-FIS2R, can't install XP onto SATA HDD

Similar Messages

Maybe you are looking for