K8T Neo - FIS2R (model 6702) SATA and RAID Problems = Hair Loss

Hi All,
new to the forum, have searched but nothing like my problem exist.
I have a K8T Neo FIS2R M/B and trying to get a single SATA HDD working for my secondary drive. primary is a IDE which works well and I want to leave it.
I have plugged in the SATA HDD into the SER 1 port ( Promise 237 ?) anyhow the bois at startup or post recognises the drive, but then says soemthing like you have set up raid before F1 for setup F2 to continue to boot.
I have pressed both f1 and F2 at various time, but it appears that it want to turn the single drive into a RAID system, which is not possible with one drive !!....
Anyhow windows XP then boots up and loads a RAID driver and also the promise RAID drivers. the real problem is that XP sits and waits for the raid which never comes and during startup on XP. it is extremely slow.
Does anyone have any ideas. I am not that computer techy as you can see by the description, but it appears that I cannot get into the RAID bios to turn it off.. I have zapped the bios to try and reset it. basically i am loosing my hair ove this.
if anyone had some step by step instructions how to prevent raid from switching on at the bios and then in XP it would be greatly appreciated
Jeff

Hi All,
Sorry for the slow reply, retrieving the box from the bottom of the swimming pool !!!
I set it to SATA as you have indicated Hans, I did check that setting. Thankyou for checking.
Spray, I have tried the P20378 setting as well. You indicate that you need to press F6 when installing the OS. I have WinXP running already on an IDE master and am trying to set the SATA up as a secondary disk drive.
As I indicated above, the machine runs slowly to the point of it being a 486 when I use either promise or Via controllers.
I have since removed the drive and are now having problems with XP on boot up/startup. The thing seems to hang or go slowly when the horizontal bar runs across under the Windows XP logo. I have turned everything off in the bios both Promise and Via. I am at a loss as to why:
1 it runs slowly with the SATA drive in ( also does not show all the auto loading icons near the clock)
2. why it hangs when I remove it and turn both SATA controllers off in the bios.
I have a feeling that I may have corrupted part of the registry playing around. Any thoughts... going bald :-)
I really appreciate the feedback so far

Similar Messages

K8T Neo-FIS2R (MS-6702)

Hi,
I have a problem (I think ...) with my mobo MS-6702 (K8T Neo-FIS2R). I have seen in the forum some messages about the bios update, etc but I have to addmitt that I have not arrived to a clear conclusion.
I have found in the MSI web that this mobo has several version of the BIOS, all of them trying to solve some stuff with the cool'n'quiet feature and the Sempron CPU.
Adding more noise to the problem, I'm one of that kind of strange people that use GNU/Linux, and simple don't have a MsWindows to test. So, no corecenter, no windows utilities, etc.
In my mobo, using the BIOS version 2.2, I can boot with the cool'n'quiet enable, but the bios doesn't detect the speed of the fans (always 0rpm) and the system is unstable.
With the 7.1 version, BIOS see and show a correct (feasible value) but the system simple, doesn't boot. I'm using a kernel 2.6.26 (Debian Lenny).
The situation here is that the Linux people says that the BIOS is buggy and the manufacturer says that they _only_ support MS. So, as always, the user lost ...
So, my questions are:
1) why this kind of mess of version numbers of the bios?
2) some one of you have been able to run cool'n'quiet in a Linux and which parameters?
Best regards,
Leo

Quote from: Fredrik on 31-October-08, 07:44:52
Neither does BIOS, (but fairly close). The fan control resides in BIOS. I'm not perfectly sure it is SmartFan, but something like that.
I think thatthat part is the corecell technology in this case by MSI
Quote from: Fredrik on 31-October-08, 07:44:52
You can test it yourself, I believe, even if Linuxian: In BIOS load SmartFan or similar and lower the processor speed. Fans should/will spin down as a result of lower temp. Notice in the link that fan control isn't explicitely(?) mentioned. ...Neither is Sempron, if I remember correctly.
It's a combination betwend BIOS parameters and kernel functions, and all that to work together. With the 7.1 version of the BIOS, I can read the fan speeds, not like the other version.

K8T NEO FIS2R can't use the RAID controller....

I have this very strange issue.
As soon as I connect a harddisk to the Promise (378) controller of this board and assign it to an array, the system doesn't work like it should.
Symptoms:
- MS Windiag (a memory testing application) reports thousands of errors
- Memtestx86 causes a spontaneous reset within seconds
- I can try to install Windows, but the process never completes; during the installation everything works really really slow (partial XP installation takes over 2 hours!)
- Linux gives me a kernel panic while booting
My system specs:
- MSI K8T Neo FIS2R (bios 1.5)
- Athlon 3000+
- 2x 512MB PQI memory (tested with GEIL/Kingston/Infineon memory as well, the problem persists!)
- Radeon 9700
- Levicom PSU (34A RMS on 12V line) (also tried Enermax 460W and Antec tru power 480W)
- 2x WD Raptor 36Gb (RAID 0 array 1)
- 2x Maxtor Diamond plus (RAID 0 array 2)
- 4x optical drive
I just can't figure out what's going on here... if I don't use the onboard RAID controller everything is fine.... but I need it for my two arrays... (besides that, it should work, shouldn't it?).
Is this perhaps just a bug in the BIOS of my system? If so... MSI please resolve this issue, my computer is worthless for the time being.. :(

Quote
Originally posted by Bas
Try this version of Memtest86.
YAY! This memory tester seems to work correctly..!
If I put a single module (PQI memory) in DDR slot 1 I get loads of errors. In slot 2 and 3 they work just fine. When combining two modules, using slot 2 and 3, I still get some errors (32, all above 1000Mb)... but it's the best I can get out of my 1Gb.
Is it safe to assume that this is a compatbility issue that can be fixxed by buying some supported memory?

K8T Neo FIS2R Won't Recognize HDDs

Here’s my situation. I am not new to building computers, but new to the AMD Athlon64, MSI boards, and SATA drives.
I purchased the K8T Neo-FIS2R (601-6702-010) main board. A single 512 MB DDR memory stick is installed. The only card installed is the ATI Radeon 7500 ALL-in-Wonder video card. I cannot get the system to recognize hard drives. I have made many changes in BIOS, but have been unsuccessful.
At first, my intention was simply to take my almost new Maxtor Diamond Max Plus 9 120 GB ATA HDD and install it with the K8T Neo motherboard. The disk has been previously formatted with Windows XP Home, and has various other programs installed. It was working fine in my older system. I put this drive (properly connected to the IDE1 on mainboard), and the K8T Neo would not recognize the drive at all. In fact, all I received were messages that SATA Raid devices were missing (apparently the Promise controller complaining). Trying to deactivate the SATA controller via bios did nothing.
Next, I decided to purchase a Seagate 160 GB Barracuda SATA HDD (ST3160023AS-RK), thinking maybe then the system would at least recognize an SATA HDD. (of course a lot of this shows my naivete’ with newer SATA standards/componets/MBoards) Initially it was recognized, and I was able to use Seagate’s software to partition the drive and format it. However, after rebooting and attempting to install Windows XP, the drive was no longer recognized by the system. On the POST screen, the VIA controller does list it as master device 1 in the SATA.
Okay, here’s what I want: I want to install the Barracuda 160 GB HDD SATA as my boot drive, and take my slightly older Maxtor HDD and make it a secondary (or slave) drive. This means a mix of SATA and ATA drives. Since MSI’s documentation both in manual and the website provides no help (that I can find) on this issue, I need suggestions on what to do. The only explanation in K8T Neo manual is to create an SATA Raid array. I do not want to do this. I simply want the SATA as boot drive, the ATA as secondary (or slave) drive, and for both of them to peacefully coexist! How do I make the mainboard recognize this?

Quote
Originally posted by saat0014
Are you getting the error when you insert the disk and it looks for the drivers on the disk? Or are you getting it at the Windows installation screen. Maybe you should try using the promise drivers and hook up your drives to the promise controller. Here's how to get the Seagate drives to work on the promise controller. Promise Scroll down to where I posted and you'll find hopefully all you need. If you need help, just ask
The error is coming at the Windows installation screen. The drivers already (seemingly) load.
I have tried installing the Promise drivers, although not as you posted in the linked thread. I only have the one SATA drive... do I still need to configure it as RAID?
I'll try this today. In all my years of building computers, I've never had as many problems as I have with this system. This is so frustrating.

[Athlon64] MSI K8T Neo FIS2R BIOS Update when? CnQ no workie!

The MSI K8T Neo FIS2R (MS-6702) hasn't had a BIOS update since 3-4-2005!
I put a Sempron 64 3000+ in my motherboard, and was very disappointed that it is recognized as an "AMD Unknown Processor". Sure, it works, but one of the reasons I bought it is in the hopes of getting AMD Cool n Quiet to work. However, apparently the AMD driver can't recognize the CPU due to the old BIOS on the motherboard.
Every other MSI skt 754 board supports Sempron E6 revision already. Why not the K8T Neo FIS2R? Where have all the MSI BIOS programmers gone? I have been waiting 2-months for a BIOS update to support the E6 Semprons. I have asked and begged MSI Tech Support. I am tempted to switch to ASUS or some other company that is actually timely with BIOS updates. Only reason I haven't yet, is this board is everything I want EXCEPT for Cool n Quiet not working. It's starting to look like there is no BIOS update in sight, so I am very disappointed.
Anyone here work for MSI can confirm there are no plans for a BIOS update? Because I don't want to wait around for something that's not going to happen.

Sorry, I didn't mean to imply I thought the mods here are MSI staff... I was just kind of hoping there's MSI staff lurking here, seeing what people think of their products or seeing what people complain about.
No, pretty much C 'n Q is the only reason I'm disappointed, but it was something I was really set on getting to work since this is a server that's up 24/7, but isn't utilized but maybe 4hrs out of a given day. I could reduce frequency and voltage, but unlike C 'n Q, it won't automatically increase speed and voltage based on demand - which is something I want since although it's a server, I also use it as a regular PC as well.
I've even tried the 2.33 beta BIOS with no change, and even found a 5.52 BIOS in their BIOS testing directory. I guess that BIOS was for a different kind of 6702, although I had pulled out the peripheral modules with AMI's MMTOOL and they looked the same as the existing BIOS, but that BIOS killed my motherboard so it couldn't have been for a regular 6702. I had to desolder the BIOS chip with a heat gun, reprogram the old BIOS back on it with an EPROM programmer, and solder in a socket. I guess that shows my dedication to get C 'n Q working!

[MSI K8T Neo-FIS2R] 2xCMX512-3200 DDR400 memories (corsair)

I have this motherboard:MSI K8T Neo-FIS2R (MS-6702) and currently i'm using a Kingston memory and the computer runs fine. But i've buyed TWINX1024-3200 (2xCMX512-3200 DDR400) but when I put only this memories the computer after some time or when booting restart suddenly...
Could it be about the bios version, my actual version is v1.0 and I'm using AMI BIOS.
i've runned memtest+ and i get this: http://korpro.org/numb/PICT1348.JPG

I am in almost the exact same situation.
MSI Neo-FIS2R
AMD XP 2800+
2 sticks of DDR400 Corsair XMS memory (CMX512-3200C2) 512mb each (total 1gig)
Any combination of memory together does not allow the motherboard to boot. I get no beeping or warning sounds. Everything powers up but the display remains blank.
Things I have tried in many different combinations:
TRCD = 5, 4, 3, auto
DDR Voltage = Auto, 2.7, 2.65
DDR 200, DDR 300, DDR 333, Auto
Memory in bank 1+2, 1+3, 2+3
Along with those bios setting combinations, I have tried using several bios versions:
v2.2
v2.0
v1.9
v1.8
v1.4 <--- (Stuck with this bios for the moment, since the ami flashing utility HANGS when attempting to erase the boot block in step 2 of flashing procedure for any newer bios.)
As a consequence of several days of trying unsuccessfully to get both sticks of memory to work, I have given up hope on this motherboard.
Why is it so difficult to get two sticks of memory working properly on this motherboard?
Has anyone got another trick or technique or setting I can try that may work?
Alternatives:
Scrap the MSI motherboard -- never buy another piece of MSI crap again.
Buy a single stick of 1gig memory.
Buy a new motherboard from another manufacturer known to work properly -- at the very least not have these memory configuration issues.
Worst motherboard experience I have ever had, unfortunately.

MY K8T Neo-FIS2R with AMD 64 3000+ auto shuts down

I have run this system for several months with core centre all
arms going off when playing graphic intensive games (Call of duty, Counter strike etc).
I have added system fans to cool the machine sown, and this seemed to work ok until three days ago when the alarm was followed by a system shut down!
I can see no obvious problem displayed in core centre, but suspect that the alarm is CPU fan speed related - I am running the AMD supplied Heat sink& Fan assembly.
Anyone have any ideas why this problem has suddenly got worse?
CPU Type AMD Athlon 64, 2033 MHz (10 x 203) 3000+
Motherboard MSI K8T Neo-FIS2R (MS-6702)
Motherboard Chipset VIA VT8383 Apollo K8T800, AMD Hammer
System Memory 1024 MB (DDR SDRAM)
BIOS V.1.8
Video Adapter VIDIA GeForce FX 5600 (256 MB)
Temperatures: (minimal load)
Motherboard 40 °C (104 °F)
CPU 44 °C (111 °F)
Seagate ST3120022A 33 °C (91 °F)
Seagate ST380011A 34 °C (93 °F)
Cooling Fans:
CPU 2860 RPM
Chassis 3013 RPM
Voltage Values:
CPU Core 1.47 V
+3.3 V 3.10 V
+5 V 4.97 V
+12 V 11.92 V
-12 V -12.20 V
-5 V -5.30 V
+5 V Standby 4.90 V
Is this a BIOS/Core Centre issue or CPU fan or maybe a PSu shortfall since the problem only manifests itself when CPU is under high loads?

Hi mcihael ,
Thanks for the tip about Fanspeed. I have seen it around but never thought i had a need of until now.
I must admit that having all of these extra applications supplied with the motherboard can get a bit confusing - the only real use that Core Center has been to me was the alarm going off letting me know that something serious was wrong!
What's your opinion on case fans? Should they be EXTRACT, INTAKE or a mixture? Most people i read about say exhaust fans are best to take away the hot air, while others claim intake fans help keep a flow of air around the CPU cooler.
Spooks

K8T Neo FIS2R (MS6702) cool n quiet problem

Hi. I have an AMD64 3000 cpu installed. The cool n quiet variable frequency is not functioning anymore. Core Center reports it at 2000mhz all the time. As a result, it is running hotter than normal and is not as quiet. I tried the latest bios (ami v2.2), the latest amd64 driver and the latest core center. The system did not like the newest amd64 driver (shutdown just as windows finished loading) so I went back to the previous versions of everything. It did work at one time but something must have changed.
System Specs:
K8T Neo FIS2R (MS-6702)
AMD64 3000 socket 754 (clawhammer or newcastle I think)
chipset K8T800
bios AMI v1.9
amd64 driver v1.2.2
Core Center v1.5.5.0
cool n quiet enabled in bios setup
dynamic overclocking disabled
Thanks for any input
Pete

Ok, this is nuts. I think its time to clear the cmos. I'm now using speedfan and even with the max speed setting for the cpu fan at 1% (one percent), the cpu fan runs at around 3800. Then it drops to zero when the set cpu temp is reached (40c). There's no in between. When I start the system, its max'd at around 4400. I pulled the fan and heatsink to clean them last weekend and it seems that's when all this started. Perhaps something went awry when I disconnected and reconnected the fan to the board. The bios version, the amd driver, and the core center version are now all the same as before I pulled the fan. I'm clearing the cmos.

6600GT not working with K8T neo-FIS2R

I recently returned a K8T NEO-FIS2R MB for repair. The problem was that the PS/2 and USB ports were broken. However the MB has been returned and the PS/2 and USB ports work fine. I posted about this several months ago.
Now the AGP port seems to be broken (not the actual slot). I have tried a 6800 Ultra and a 6600 GT (AGP version) GFX card in this slot. Both cards fail at the driver installation point. I have tried driver versions 66.93, 67.02 and 67.03. I also tried 3 versions of the via drivers 451, 453 and 455. Even tried XP with SP1 and SP2. The PC will sometimes BSOD, reset, won't boot into windows. The drivers sometimes install then other times they won't, etc. The problems only seem to be with the drivers for the GFX cards.
The 6600 GT works as I have tried it in another MB without any problems.
I know the memory works fine as I used memtest86+ for a couple of hours on the default settings without any errors and it works in another PC.
The spec of the PC is:
XP pro
K8T NEO-FIS2R MB
512MB corsair XMS at 2.5-3-7-3
XFX 6600GT
40gig HDD
FDD
Plextor CD writer
DVD Rom
PSU is a Q-tec 550W
I know Q-tec PSUs are not up to much from what I have read elsewhere in this forum, but I have had it running in a similar system with the 6800 Ultra installed without any trouble (even with the above MB before it went faulty). I have also tried a 400W PSU, that came with the case. The Voltages on the 12V line are between 12.00 and 12.03 when using the Q-tec PSU.
Has any body else had these problems with the 6600GT in the mentioned MB.
Also, how can I check the serial number on the MB with the label on the box, as this MB that was returned to me looks to “clean” to be the one I sent away for repair.
Thanks for any help

Hey, I'm glad to see a post on the new Gforce 6600GT AGP card. I just recently put together a brand new system (see my sig for specs). System runs great. The only thing I wanted to do was replace the video card, and after a great deal of anxiety I decided the Geforce 6600GT AGP was the best bang for the buck.
Well I got home, installed the card and never get passed the bios screen. (shows your processor, memory, memory siz), the screen u hit DEL to go into the bios.
The system doens't lock up, NUM LOCK can still be turned on and off, and CAPS can be turned of and on... but thats it. Just sits on that screen. I can't go into the bios either.
what settings do I need to do prior to isntalling this card to get it to work.
Let me know if you all need anymore details to help me out.
oh, I did reset my frequency to 10x200 (which is what I think the 3000+ is supposed to be at).

MSI K8T NEO FIS2R No VGA help plz!

Hi, ive just purchased a new athlon 3000 64 cpu retail and an msi k8t neo fis2r motherboard, the specs and problem are below but plz bare in mind i am a system builder for the last 3 years i have tried alot of things to solve this.
MSI K8T NEO FIS2R MOBO
AMD 3000 64 RETAIL CPU
AMD RETAIL HSF
1024MB DDR333 SAMSUNG RAM
120 GIG WD HD
GALAXY GLACIER GEFORCE 6800 GT 256MB
PIONEER 106 DVD WRITER
400 WATT PSU (TSUNAMI I THINK)
Anyway the problem is this when i put the system together and turned it on i dont get any vga the monitor just says NO SIGNAL and when i look at the graphics card the fan on it isnt spinning.
Yet i have my old setup which is as follows,
ASUS A7N8X DELUXE MOBO
AMD 3200XP BARTON
AMD HSF
1024MB DDR333 AMSUNG
120 GIG WD HD
GALAXY GLACIER GEFORCE 6800 GT 256MB
PIONEER 106 DVD WRITER
400 WATT PSU
Basically the same as above i just changed the cou and mobo now when the graphics card is in that system it works fine no problems as soon as i try it in the new a64 system it doesnt work the fan doesnt spin and nothing comes on screen, ive tried everything i know ive double and trebble checked connections and ive tried removing components and then trying it, no matter what the graphics wont work.
I figured the motherbaord must be faulty and am going to contact the place i got it from but it would be good if anyone here knows how to solve it if it isnt the motherboards fault.
thanks very much.
ic3man1999.

Thanks guys, huess what like an idiot i forgot to put the 4 pin 12v in :( doh
Anyway it works fine now, but i have high temps core centre says 56 degrees right now while im typing this ? is this accurate or am i in trouble ?
Oh yeah and everytime i load windows it says new hardware found ide channel then secondary ide channel then it says a problem occured during your new hardware installation and it calls the hardware HDC it says this twice aswell.
ANy help guys ?
thanks

MOVED: K8T Neo-FIS2R SATA and Linux Question

This topic has been moved to Operating Systems.
K8T Neo-FIS2R SATA and Linux Question

Quote
Originally posted by chasmon
Hi all,
I have just setup up a brand new system but am having probelms getting it working. I want to install XP on a single Maxtor 160Gb drive.
I have my HD on Promise Ser1 and all SATA stuff in BIOS enabled. When I get to the screen I press F6 and then when promted I insert the floppy with the promise drivers on. I then get this message:
"File txtsetup.oem caused an unexpected error (4096) at line 1742 in d:\xpclient\base\boot\setup\oemdisk.c"
I can't get past this screen I have tried:
1.Drivers from the CD supplied.
2.Drivers from the MSI website.
Please help me this lot cost lots of hard earned I'm pretty gutted at the moment. I have also tried the Via chipset with no joy.
System:
Antec 380W PSU and Sonata Case
LG DVDROM 8163B
NEC DVDR/RW 2500B
Panasonic Floppy
Neo FIS2R mobo
Maxtor Diamondmax Plus 9 160Gb SATA150
Benq RF K/B & Mouse
Don't spam man! I posted something to this same question in another thread.. from you no less! Make a new thread! lol
Hijacking = bad!
Ian

MSI K8T Neo-FIS2R SATA CD/DVD Support

Does anyone know if the K8T Neo-FIS2R mobo will or can be made to support a SATA CD/DVD drive. I am having no luck so far either getting it to recognize the drive or finding any info as to such.
Any help will be greatly appreciated.
Cheers

I was able to answer my own question. I was doing a bit of searching around on the MSI website and happened across a newer bios that doesn't come up in a regular search. The regular search turns up this page http://www.msicomputer.com/support/bios_result.asp (obviously inputing the correct platform and model) showing BIOS v2.2 as the most current. But by poking around on the site a bit, I came across another BIOS page for the same mobo, http://global.msi.com.tw/index.php?func=downloaddetail&type=bios&maincat_no=1&prod_no=565 showing BIOS v7.1. I figured I'd give it a try and low and behold the bios is recognizing my SATA DVD Burner.
The hd array has to be connected to the Promise controller as it will not see the optical drive even if it is set to SATA mode. I hooked the SATA DVD burner to the VIA controller and changed the setting in the bios for this controller to SATA mode as opposed to RAID mode (this was not an option on this controller in the BIOS before the flash to v7.1). I also had to have the PATA controller set to enabled or it would not recognize the drive. It is now a recognized device and shows up as an option in the boot menu. I added an additional SATA DVD drive to the other VIA SATA connector and it recognized it right away and made it available as a boot device. I tested with Knoppix and it booted fine.
Hopefully when I try to load XP this evening, I will have a winner.
Thanks again for your replies!!!

MSI K8t Neo FIS2R RAID Question

I've just put together my new system. If it weren't for this forum, I might not have succeeded. Thanks for all the info out there.
Currently, I'm running raid 0, using (2) raptor 74's. The next thing I want to do is mirror. I bought a 160 gig maxtor ata drive for this purpose. But, after seeing the table in the MSI raid manual, it looks like I have to use (2) drives the same size as the raptor 74's inorder to use the raid 0+1 configuration. Any help on this would be apreciated.
MSI K8t Neo FIS2R
Athlon 64 3200
Kingston (2) 512mg Hyper X DDR500
Western Digital 74 gig Raptors (2) raid 0
Nvidia Geforce Ti 4200 128mg graphics
shydragon

but mirror raid wont save you from oc crash's , virus, bad installs, acidently, deleteing or any useful recovery..it only protects from hd failure to mechanical or electrical malfunction.
you are far better off imagine the drives or mking backups, and using the drives as storage for that, you will come out ahead.
but if you still want raid 1, you can
partition the drives?
use the smaller ones for system restore , and internet cache, mp3's . for example
for rich performance freaks buy 2 more satas and raid them on the other chip
just a few ideas

K8T Neo-FIS2R - raid 1 refused by Win2K

Hi,
I had K8T Neo-FIS2R for some time, working flawless. I had 1 ATA drive (Maxtor 120GB, 8MB) on a VIA controller. Then I decided to buy another similar one ATA HD, and create a raid 1 array (ATA+ATA) on Promise controler, with existing Win2K SP4 instalation.
Everything went smoothly, creation of array and image on second HD. Then reboot, Windows start loading... and suddenly BSOD. Message: "If this is your first time seeing this message...check for viruses...corrupted HD...blah blah".
Tried loading again and again - same situation.
Then I discarded array, rebooted, and created it again. Same problems. And headache & rage.
Few days later, I had a possibility to borrow a new SATA Maxtor 120GB drive, and try with ATA + SATA raid 1 combination. Done everything from the beggining, creating of array and image, at the end...again BSOD with the same message. 100% identical like in 2xATA combination.
I thought that maybe the problem is in "original" ATA HD, so i tried with another combination: second (new) ATA HD from first situation (image of original HD was still on it, but with discarded array), anda SATA from second as a "slave" (so, this one is deleted in creating of this array). Same, same, same... Needless to say, at the end I tried with SATA as "master" and ATA as "slave". No progress.
BIOS and all drivers were/are up-to-date. All HD`s work OK in a "no raid" situation, on both controllers.
I have searched this forum, but didn`t find similar problem. If you have some ideas/suggestions/solutions, you will be a hero, for saving a one young man`s life
Thanks in advance,
Buca,
Belgrade, Serbia

Quote
Originally posted by Tiresmoke
Promise ATA raid can only work though the Promise ports which in the case of ATA or Ultra ATA drives would be IDE3 port. Then you must have Promise Raid turn on in the Pheriferals menu in Bios as well as set up under the Promise Raid section that will come up directly after post.
You will need to read the Promise Ademdum manual that came along with the regular user manual for setup details.
Thanks for trying to help, but I have done that all. I can create a raid array with ATA drives only on Promise...

K8T Neo-FIS2R and 2.2 bios problem

I flashed the bios of my K8T Neo-FIS2R to version 2.2.
Everytime I boot the system, I can just see the Windows XP logo appearing for a second, then the system reboots again.
I reflashed from a floppy to version 2.1 again, but still the same problem.
My HDD is a Western Digital SATA drive on the VIA controller.
Can somebody please help me out?
THX!
Marco

Thanks for your support!
After reflashing to 2.0 I still had the same problem.
The bios was not causing the problem. In some way, Windows couldn't load the SATA driver properly, I think.
I removed the SATA HDD from the VIA controller and connected it to the Promise controller, and surprisingly, Windows started again.
The HDD LED works on the Promise, but not on the VIA, so I left the HDD on the Promise controller. The LED problem is now solved as well.
I still don't know exactly what was going on. Anyway, it wasn't MSI or the new bios, it was Microsoft...
Marco

K8T Neo - FIS2R (model 6702) SATA and RAID Problems = Hair Loss

Similar Messages

Maybe you are looking for