K8t Neo-fis2r - not booting!!!

Hello Motherboard gurus! Any help would be appreciated...
Here are my system specs:
AMD Athlon 64 3000+
Motherboard /AMD Socket 754 CPU’/ "K8T NEO-FIS2R"
RAM - Kingston 184 Pin 512MB DDR PC-3200 X2
Hard Drive – 120GB – Maxtor 120GB 6Y120PO
TEAC 1.44MB 3.5 Black Floppy Disk Drive
ThermalTake Silent PurPower 360WATX Power Supply
Lite-on DVDR – Model LDW/811S/851s BLK
ATI AIW RADEON 9600 Video Card, 128MB DDR, 128-bit, CATV/Video Out/Video In, 8X AGP, Model "ALL-IN-WONDER 9600"
Everything was working just fine until I switched out my CPU fan for a super quiet Zalman fan. I hit the power and nothing, but the fan spins up just fine. No video. The LED's on the back cycle through a couple of settings and sit at all green except for the upper left at red. I am at a loss ...perhaps the video card? I tried replacing the original fan and got the same result
Thanks in advance for any help,
JD

Your power is weak for sure. However you may also be seeing a fan that runs to slow for the motherboard to read. If the speed drops below what the MB expects it will cause issues as it thinks the CPU fan is dead and may not want to operate at all. Check that by reinstalling your old fan. Also on the power issue what is the 12v rail amps on that PSU?

Similar Messages

K8T Neo-FIS2R No boot - Early Chipset Initialization LED

Went from a MSI K7N2 Delta-ILSR with XP 2500+ O/C'd to 3200+ to an MSI K8T Neo-FIS2R board with a retail Athlon 64 3200+ and a Thermaltake Silent Boost Heatsink/Fan combo.
RAM = 2 x 512MB Apacer PC2700 (MSI approved).
Video= ATI 9800 Pro AIW
Antec Sonata case with 380Watt True Power +12V-18A, +5V-35A, 3.3V-28A
Seagate 160GB SATA 7200.7 drive.
On boot, system hangs at #1 red LED indicating Early Chipset Initialization.
Video is blank, all switches work, all drives spin up, no beep codes, just dead.
Tried just CPU, Fan/Heatsink, Video and still same.
Without any RAM, system beep codes for RAM.
Tried RAM in slots 1 and 2, 3 and 4 and just one by itself. Never a change to the DBracket light.
Cleared BIOS and retried. Nothing. No video at all.
What does that "Early Chipset Initialization" mean anyway? I guess the board is bad. This is it's first boot attempt.

Well, I think I know what the problem is, aside from the PSU... I tried my brother-in-laws 550 PSU that pushes 24A on the +12V and it did not budge. I think it is the board. I did an RMA with Newegg and will be sending it in for a replacement.
Thanks for the advice on the PSU's... I will be heading back to Newegg to get one.
As an aside, I did get a new PSU since my last post. It was a Maddog Multimedia 550 that is made by Thermaltake. The voltage is not listed on the outside of the box, so, once I opened it, I noticed a couple things. One, it is a 480 not a 550, and two, the +12V is a paltry - abismal - 18A! This was CompUSA's best power supply and cost $140 after taxes! (I wanted one now, not in the few days it takes Newegg to get me one). Needless to say, it is going back. Since the numbers were not on the outside of the box, they are taking it back without a restock fee.
I will quell my desire for now now now and wait until a good one from Newegg arrives. I will let you know of my results!
ps - I am toying with the idea of the PC Power one... !

K8T Neo FIS2R not getting through POST

I hope some of you might be able to help me. I just finished building a new system using the K8T Neo FIS2R motherboard. I actually had everything working with XP installed, but this morning, I have not booted once. It's not clearing POST anymore.
I get a long beep followed by 8 short beeps. According to the BIOS beep codes I've seen in other posts, that has something to do with the BIOS checksum error. I did upgrade the BIOS to 1.7 from an MSI Live Update download.
I'm basically stuck, is the mobo dead?
K8T Neo FIS2R
AMD Athlon 64 3000+
2 512MB Kingston Memory Modules
MSI ATI Radeon 9800 Pro 128MB
Power Supply :
+3.3 / 32A, +5 / 40A, +12 / 24A, -12 / 1.0A,-5 / .5A, +5SB / 2A
If you need more info, just reply.
Thanks,
-Erik

kawasakiguy37 and others
This does not bode well for my current situation, or yours. I have to believe that there are many people out there that have a successful 1.7 BIOS running.
But I'm beginning to lead in this direction now, especially since your description is close to mine. I was able to run in v1.7 for a short time, then it just died.
Also, I don't know if this helps, but after my beep codes, I assume the POST continues, because about 15 seconds later there is 2 short beep following by 1 long beep and the D-bracket is has green all around minus number 4 which is read. Assume blue=green here :
This is "Testing RTC (Real Time Clock)". At this stage it just stops.
I am assuming that I can flash my BIOS using the cntrl-home method, however, if that fails, are we looking at RMA here... And if so, what are peoples experiences with RMA'ing with an online dealer? How much proof will I need to go through?
Also, by the way, these forums are awesome... The data here has been great. It's nice to see such a great forum that has valuable information.
Thanks to everyone for the help so far.
-Erik

K8t neo mobo not booting when any usb devices plugged in!

as stated above, my pc now will not boot with any usb devices plugged in at all
once they are disconnected, its all fine, will boot right thru to windows, where I can just plug em back in
it didnt used to do this, just started one day, didnt change anything etc
I;ve tried a format/reinstall of windows just in case it was that, but no!
anyone got any ideas??

If you are having problems with USB ports, read this topic.

K8T Neo will not boot - Help!

I purchased an AMD64/MSI bundle that refuses to work. I did return the bundle to Komplett but they say it checked out 100% and returned it. Reading threads I can see certain PSU's or RAM could cause problems.
I have detailed the kit below but when I assemble the complete kit and power it on, I hear the HD spin but that’s it. The monitor stays in standby. The 4 lights on MSI “D-Link” are all red & the lights on my keyboard keep flashing. I also tried just connecting absolute minimum items as per FAQ to see if that nailed the problem but is the same result every time. The PSU is a fairly decent Enermax model. The RAM came part of the bundle and works in other machines (anyway Komplett checked it out). The only thing I can think of is that the OS is on a 120GB IDE HD and I also have a 250GB SATA backup drive. This is the 3rd system I have built. Can anyone point me where I could be going wrong as it seems a waste of money with this great bit of kit just sitting in a cardboard box!
KIT:
(forgot PSU) Enermax EG651P 650Watt
AMD 64 3200 Socket 754
MSI K8T Nero-FSR (754K8T800, SATA/ATA, GbLAN)
RAM Crosair Value PC3200 512 (plus 2 more sticks of 256MB)
Maxor ATA 120GB
Maxor SATA 250GB
ATI 9700pro
Sound Blaster Audigy 2
Liteon CDRW
Liteon DVD/RW

Quote
This is the 3rd system I have built.
...don't let this shake your confidence...it was a curve ball, you swung and missed...no big deal...
...I do the same thing...

6600GT not working with K8T neo-FIS2R

I recently returned a K8T NEO-FIS2R MB for repair. The problem was that the PS/2 and USB ports were broken. However the MB has been returned and the PS/2 and USB ports work fine. I posted about this several months ago.
Now the AGP port seems to be broken (not the actual slot). I have tried a 6800 Ultra and a 6600 GT (AGP version) GFX card in this slot. Both cards fail at the driver installation point. I have tried driver versions 66.93, 67.02 and 67.03. I also tried 3 versions of the via drivers 451, 453 and 455. Even tried XP with SP1 and SP2. The PC will sometimes BSOD, reset, won't boot into windows. The drivers sometimes install then other times they won't, etc. The problems only seem to be with the drivers for the GFX cards.
The 6600 GT works as I have tried it in another MB without any problems.
I know the memory works fine as I used memtest86+ for a couple of hours on the default settings without any errors and it works in another PC.
The spec of the PC is:
XP pro
K8T NEO-FIS2R MB
512MB corsair XMS at 2.5-3-7-3
XFX 6600GT
40gig HDD
FDD
Plextor CD writer
DVD Rom
PSU is a Q-tec 550W
I know Q-tec PSUs are not up to much from what I have read elsewhere in this forum, but I have had it running in a similar system with the 6800 Ultra installed without any trouble (even with the above MB before it went faulty). I have also tried a 400W PSU, that came with the case. The Voltages on the 12V line are between 12.00 and 12.03 when using the Q-tec PSU.
Has any body else had these problems with the 6600GT in the mentioned MB.
Also, how can I check the serial number on the MB with the label on the box, as this MB that was returned to me looks to “clean” to be the one I sent away for repair.
Thanks for any help

Hey, I'm glad to see a post on the new Gforce 6600GT AGP card. I just recently put together a brand new system (see my sig for specs). System runs great. The only thing I wanted to do was replace the video card, and after a great deal of anxiety I decided the Geforce 6600GT AGP was the best bang for the buck.
Well I got home, installed the card and never get passed the bios screen. (shows your processor, memory, memory siz), the screen u hit DEL to go into the bios.
The system doens't lock up, NUM LOCK can still be turned on and off, and CAPS can be turned of and on... but thats it. Just sits on that screen. I can't go into the bios either.
what settings do I need to do prior to isntalling this card to get it to work.
Let me know if you all need anymore details to help me out.
oh, I did reset my frequency to 10x200 (which is what I think the 3000+ is supposed to be at).

K8T Neo FIS2R AMIBOOT.ROM not working

Hi
Had a game crash on my system, and froze everything, so had to restart manualy - now I get the error BIOS is not installed..
I have downloaded a copy of the bios (not latest) and changed the relevant ROM file to AMIBOOT.ROM and copied to a freshly formated floppy.
I inserted the disk, held down CTRL and HOME and started the computer...
After a while of running through the messages of BIOS not installed and no SATA installed (which is correct), the floppy drive light comes on, and then after a while (afet I have released the CTRL and HOME keys) I get a message saying "Remove disks or other media, Press any key to restart" then nothing, if I press any key - it says the same thing untill I remove the floppy... and then it restarts again.
I have tried to restart using the floppy and the CTRL and HOME keys about 20 times so far - always the same result - I have even tried diferent versions of the BIOS.
Any ideas?
I only have one stick of RAM (256Kb - 333) and two IDE HD's
Many thanks in advance
GreenBoy

Hans
My Set up is as follows (from the top of my head as I am doing this form work)
K8T Neo FIS2R.
AMD 3300 745pin chip set.
1 stick of 512Mb ram (non branded - baught from Watford Electronics)
2 x 200Gb Maxtor HD's
1 40GB Seagate HD
1 DVD RW
Power 500W
Dont know what else you need...
Anyway - last night I reset the CMOS in the way you described.
Still cant find the VIA settings in the Advanced Chipset or elsewhare - but I will. urned of SATA in Intergrated Peripherals...
Anyway - what then happens, is it says it cannot boot.
I tried using a Win98 SE boot disk - and all the drivers were listed as not possible to load or something...
Any way - deciding I did not have anotehr boot disk to hand - tried Symantec Ghost - still same result.
Finaly I tried WinXP Pro, and found that this installed all the bootup files no problem at all - what was then found was that my C: partition was missing - yup boot sector had completely disapeared.
Anyway knowing that I have recent full backups og my primary drives using Ghost, I took the plunge, created a partition in the unalocated space, reformated the drive, and reinstalled WinXP... all seems ok for now... except the message regarding no BIOS - but from what you say as soon as I fing the switch I will loose that again.
The strange thing is I never used to get this message before, and do not remember setting anything up for SATA - couldnt afford the disks at the time....
Thanks for the help Hans, you have been more than gwenerouse with your time , but can you please give me some more information? (Im a bit of a Nooby at playing with BIOS etc as they scare the crap out of me! )
1) Why is the detail of my system so important? I have made no Hardware changes for approx 6 months and everything was fine untill the game crashed, so therefore, dont see why this should affect things.
2) Why did the flashing of the BIOS not work? I was following the instructions carefully - but nothing.. therefore in my Nooby mind this means there is something else wrong, stopping the flashing from working.
Again - many thanks
GreenBoy

Booting "issues" with K8T Neo-FIS2R

Well hello everyone. First of all I want to say that my English isn't completely error-free and my problem might seem awkward because of my ways of expression.
I also want to say that i've read alot of threads and searched the forum for my problem.
For a couple of days ago I got all my parts for building my 64bit-system and I build her up. To my suprise it booted, with almost no errors. Although I could install Windows XP and use it completely, everytime I boot it (under the booting sequence) it says "Bios is not installed", although I can enter bios simply (like everyone else) just pushing the DEL-button.
But this isn't the only problem. When I enter PC Health Status it says that the cpu is running at whooping 62-65 degrees. When i have my hand around the cpu-cooler it doesn't even feel warm so I think it has something to do with my BIOS-version that i am running now (Yes, I've read that in much more threads)
Also I have problems using the Cool'n'Quiet technology. I have it supported in the BIOS and activated it although it will not work (maybe it has something to do with the bios?) With this i mean that i will not go underclocked (It's allways 2.2 GHz)
My final problem is that it sometimes takes the system 2 minutes to boot sometimes, it happend after i flashed the bios to 1.7 from 1.0
Under these circumstances I've used 1.0 AND 1.7 BIOS-versions.
I've never overclocked the computer either.
What could be wrong?
I'm using 3200+ 2.2GHz Athlon 64 cpu.
K8T Neo-FIS2R
Radeon 9800pro
Seagate 7200.7 200GB drive.
380W Antec PSU.

Quote
Originally posted by $post[username]
I've tested notebook, minial power savings and battery. C'n'q still doesn't seem to work. Yes i've enabled it in bios. I downloaded the AMD Athlon™ 64 Processor Driver for Windows XP, Version (zip) 1.1.0.14 -
Yesterday my CnQ began to work fine. I've done the same as you:
1- Enable CnQ Bios option
2- Install the AMD athlon64 driver for XP
3- Set "minimal power savings" at windows xp energy options
I have installed the CoreCenter 1.6.8.0 (is the last version) utility, and I've set enable the CnQ in this application. You'll can see that the CPU velocity change "on demmand" and the CPU fan too.
Of course, I've the last VIA 4in1 drivers, 1.7 Bios ver. etc
My temp & MHz values are:
~40ºC ~ 800 MHz idle
~50ºC ~ 2000 MHz playing or that kind of stuff
Note that the PC case is open, because the PC is under my table and there is no good ventilation.

Boot issue: K8T NEO FIS2R

Hello,
I am having a boot problem. I have the K8T NEO FIS2R, 512 meg ddr400 in the middle slot, an ati radeon 9800 pro, and and 3000+ cpu. Everything was working fine last night, i was playing hl2 and all was well in my world.
So this morning i remove a disfunctional cd device and replace it with another and now the system won't boot past the msi/core cell screen. I did update the bios with the msi live update utility but I am 98% sure i rebooted the system successfully since i did that. My computer is really new (2 days old.)
Can anyone tell me what I can do to fix this? What causes the thing to not boot past the initail screen? Could the bios be wasted maybe? I already cleared the cmos. Thanks for any help, I am having hl2 withdrawals. I hope I don't have to return the mb.
thanks,
freakmachine

Hi
If the CD caused the prob check no pins are bent, and that its jumper is set correctly, if its a master, put it on end connector of cable, red strip near power connector. Also change the cable for CD, maybe it is the cable not the drive. Reset boot sequence, if you changed a drive it will need reset.. Did you disable the Boot sector virus protection before flashing the bios.
Cheers
jocko

K8t neo fis2r - core center not functional after installing sound card

Hi. I had been using Core Center with Dynamic Overclocking enabled and all was well. When idle, my amd64 3000+ (2.0ghz), was running at 800mhz. Under load it would go up to 2100mhz. But yesterday, I installed an Auzentech x-plosion sound card and after i installed the driver, the dynamic overclocking stopped working, my cpu is running at max all the time. (The variable fan speed function still works).
I checked the IRQ and there is no conflict, I uninstalled the amd64 driver and core center and reinstalled. Still does not work. I uninstalled the auzentech driver, rebooted, and cancelled new hardware wizard. Then the variable cpu frequency feature worked. Once I install the driver for the auzentech, dynamic oc stops working. I was thinking to try another pci slot but it appears to be a software issue rather than a hardware issue. The new version of Core Center does not work with my board even though msi says it's compatible so I'm still using the one that always worked. The amd driver is the latest and also always worked.
Has anyone else had a similar problem, perhaps using the auzentech sound card with this board and Core Center? Or does anyone have any suggestions?
Thanks!
K8T Neo FIS2R
AMD64 3200
AMI bios version 2.2
1.5Gb pc3200 memory
nvidia quadro FX 1100 128mb AGP
Antec 430W ps

Hey guys, I just went to AMDs site to get the dashboard utility mentioned and in the readme, it stated that in XP, the power option needs to be set to portable/laptop. But in the past, I read that it needed to be set to "always on" and that it is, in fact, what I had it set to before when cool n quiet was working. Now I change it to "portable/laptop" and it works and set to "always on" doesn't work anymore. So now Core Center reports I'm at 33c @800mhz at no load. I don't get it??? I'll have to try an alternate utility just to verify that is indeed working.
btw, QV, I checked system properties, (right-click my computer > properties, or "system" in control panel) and on the "general" tab, it indicates an AMD64 3000+, 2.0GHz. But I'm pretty certain the clock frequency is dropping now as reported by core center because of the decrease in the cpu temp at idle. Am I looking in the right place in XP? I have XP pro, SP2
Again, thanks for the input and Happy New Year

Msi k8t neo fis2r problems part 3

sometimes when the computer is turned on it just turns the fans and leds on but doesnt boot up...
most of the time it loads up and i boot to the windows xp cd and i install the drivers for sata and then when it reaches the point of copying the files it will give me a bsod and say that there is a problem with the irql driver and then force me to shut the pc down..
sometimes it makes it past that and will begin to copy files onto the hard drive, like somehow the data is becoming corrupted..however it will start to say that the files cant copy randomly and it will allow me to retry..they will copy the 2nd time usually..i can keep hitting retry and it will usually go by..it gets to 30 something % and then crashes to bsod just giving me some random error..for some reason the files keep screwing up that go on the sata drive....I just replaced the old power supply that wasnt working with an antec true watt 430 watt power supply, so i know it isnt that..
i just cant figure out what the heck is going on..any help would be appreciated.my specs are
"IRQ NOT EQUAL OR LESS"
athlon 64 3000+ cpu
msi k8t neo fis2r motherboard
mushkin special cas 2.0 2-2-2-5 512 mb pc 3200
western digital 8mb cache 80 gb sata hard drive
sapphire radeon 9800 pro 128 mb 8x agp

fyi look an your cd sticker ity will show power, consumption, but they are way lower than you would think, hard drives,can be only 10 watts, less then some case lights , and fans, cd are similar.. your video, is the biggy somewhere between 90~150 watts..yikes .next to the cpu..and the mobo can use 50 or so (not sure about new mobos) not to mention the ram 1024 is @40 watts or so., dont forget about 25watts per pci card, not counting the sound card which can be double....
ergo the need for a big psu..
the combined total ratting on a psu is not the max number that the psu is rated, that is surge value.. so a 500 may only hold 400 sustained , and that will drop as the machine heats up, so in the end your 500 may onlyy pull 366 @50'c...

[MSI K8T Neo-FIS2R] 2xCMX512-3200 DDR400 memories (corsair)

I have this motherboard:MSI K8T Neo-FIS2R (MS-6702) and currently i'm using a Kingston memory and the computer runs fine. But i've buyed TWINX1024-3200 (2xCMX512-3200 DDR400) but when I put only this memories the computer after some time or when booting restart suddenly...
Could it be about the bios version, my actual version is v1.0 and I'm using AMI BIOS.
i've runned memtest+ and i get this: http://korpro.org/numb/PICT1348.JPG

I am in almost the exact same situation.
MSI Neo-FIS2R
AMD XP 2800+
2 sticks of DDR400 Corsair XMS memory (CMX512-3200C2) 512mb each (total 1gig)
Any combination of memory together does not allow the motherboard to boot. I get no beeping or warning sounds. Everything powers up but the display remains blank.
Things I have tried in many different combinations:
TRCD = 5, 4, 3, auto
DDR Voltage = Auto, 2.7, 2.65
DDR 200, DDR 300, DDR 333, Auto
Memory in bank 1+2, 1+3, 2+3
Along with those bios setting combinations, I have tried using several bios versions:
v2.2
v2.0
v1.9
v1.8
v1.4 <--- (Stuck with this bios for the moment, since the ami flashing utility HANGS when attempting to erase the boot block in step 2 of flashing procedure for any newer bios.)
As a consequence of several days of trying unsuccessfully to get both sticks of memory to work, I have given up hope on this motherboard.
Why is it so difficult to get two sticks of memory working properly on this motherboard?
Has anyone got another trick or technique or setting I can try that may work?
Alternatives:
Scrap the MSI motherboard -- never buy another piece of MSI crap again.
Buy a single stick of 1gig memory.
Buy a new motherboard from another manufacturer known to work properly -- at the very least not have these memory configuration issues.
Worst motherboard experience I have ever had, unfortunately.

K8T Neo-FIS2R (MS-6702)

Hi,
I have a problem (I think ...) with my mobo MS-6702 (K8T Neo-FIS2R). I have seen in the forum some messages about the bios update, etc but I have to addmitt that I have not arrived to a clear conclusion.
I have found in the MSI web that this mobo has several version of the BIOS, all of them trying to solve some stuff with the cool'n'quiet feature and the Sempron CPU.
Adding more noise to the problem, I'm one of that kind of strange people that use GNU/Linux, and simple don't have a MsWindows to test. So, no corecenter, no windows utilities, etc.
In my mobo, using the BIOS version 2.2, I can boot with the cool'n'quiet enable, but the bios doesn't detect the speed of the fans (always 0rpm) and the system is unstable.
With the 7.1 version, BIOS see and show a correct (feasible value) but the system simple, doesn't boot. I'm using a kernel 2.6.26 (Debian Lenny).
The situation here is that the Linux people says that the BIOS is buggy and the manufacturer says that they _only_ support MS. So, as always, the user lost ...
So, my questions are:
1) why this kind of mess of version numbers of the bios?
2) some one of you have been able to run cool'n'quiet in a Linux and which parameters?
Best regards,
Leo

Quote from: Fredrik on 31-October-08, 07:44:52
Neither does BIOS, (but fairly close). The fan control resides in BIOS. I'm not perfectly sure it is SmartFan, but something like that.
I think thatthat part is the corecell technology in this case by MSI
Quote from: Fredrik on 31-October-08, 07:44:52
You can test it yourself, I believe, even if Linuxian: In BIOS load SmartFan or similar and lower the processor speed. Fans should/will spin down as a result of lower temp. Notice in the link that fan control isn't explicitely(?) mentioned. ...Neither is Sempron, if I remember correctly.
It's a combination betwend BIOS parameters and kernel functions, and all that to work together. With the 7.1 version of the BIOS, I can read the fan speeds, not like the other version.

K8T Neo-FIS2R / Kingston KVR400X64C25/256

As a first time poster my apolgies if this has been covered elsewhere - I have read most of the posts on this forum but found no specific reference. Please just point me in the right direction if i am wrong!
I bought the Kingston KVR400X64C25/256 modules because:
a) they were listed by MSI on the list of tested Ram
b) they were on Kingston's list for the K8T NEO &
c) they were in stock. However...
If installed in DIMM 2 & 3 (as per MSI tested RAM pdf) the system crashes on trying to load Windows. DIMM 1 & 2 'works' if that allows for 8 or 9 restarts/day. I tried 1 & 3 to see if that improved the situation, but if anything it was worse. I have tried increasing the RAM voltage to 2.6 but there is no discernable difference. Upping the TRCD to 4 makes little or no difference.
Memtest86+ initially found no errors (16 hrs/93 passes) but when left running for a week came up with 10 errors (8 in test 6, 2 in test 4). MemTest (http://hcidesign.com/memtest/) gives me an average of 10 errors for 300% pass.
I'm now trying running the memory at 2.7v (within Kingston's ±.25v range).
In the meantime, has anyone run this memory without any problem - i.e. is it a simple case of faulty memory? Equally, has anyone had similar problems and found a solution?
thanks
MSI K8T Neo-FIS2R
AMI rev 1.2
AMD Athlon64 3000+ AMD heatsink/fan (working temp around 32°C)
2 x Kingston KVR400X64C25/256 (DIMM 1, DIMM 2)
NVidia GeForce3 driver v53.03
Antec TruePower 430W +3.3V 28A, +5V 36A, +12V 20A. Max load 410W
IDE1 ST340016A (master) ST320014A (slave)
IDE2 MSI DVD-ROM D16 (MS-8216)
Soundblaster Live 5.1 platinum
Windows XP Pro Version 2002 service Pack 1

Quote
Originally posted by Bas
Hi,
Sorry to say, but as soon as you get errors in memtest, no matter after how many hours, you need to try other memory.
As your memory seems to be unstable....errors in memtest are a NO-NO
hmmm! What if memtest, Prime95 etc. detect no problem over lengthy periods when sticks are individually tested in DIMM1 - as well as the system not crashing once - , but boot failures/memory dumps etc. abound when same sticks are individually placed at 2 or 3? Is this still a memory issue?
For what it's worth I have found Kingston's technical support more than helpful.
MSI K8T Neo-FIS2R
AMI rev 1.2
AMD Athlon64 3000+ AMD heatsink/fan (working temp around 40/42°C)
2 x Kingston KVR400X64C25/256 (DIMM 1, DIMM 2)
NVidia GeForce3 driver v53.03
Antec TruePower 430W +3.3V 28A, +5V 36A, +12V 20A. Max load 410W
IDE1 ST340016A (master) ST320014A (slave)
IDE2 MSI DVD-ROM D16 (MS-8216)
Soundblaster Live 5.1 platinum
Windows XP Pro Version 2002 service Pack 1

K8T Neo-FIS2R/FSR no POST

I have a K8T Neo-FIS2R/FSR (MS-6702) which is, along with all my other components (I'll list them later), over a year old. It has been running just fine until the other day. I have not modified any hardware or BIOS-settings recently.
The day before yesterday my speakers put out a high-pitched shriek and the screen turned black. I then turned off the computer (it seemed to still be running, fans spinning). As I switched it on it let forth 8 beeps followed by a paus, and then 8 beeps again, over and over. I switched the graphics card for another one, no difference.
I then left it turned off for a few minutes. Then I booted it up again, and voila, it worked fine. Then after a few minutes it died the same way, and when I rebooted it it started beeping again.
Switching graphics card doesn't help. I powered it on without a graphics card plugged in. Then it made 8 beeps, and then silence. The cycle was not repeated, as it was when the card was in.
I then used another motherboard, another CPU and other RAM, same graphicscard and harddrive, and it boots into Windows just fine and seems to be quite stable for the day I've tried it.
I then switch back to the K8T-motherboard with it's CPU and RAM (still same graphicscard and harddrive as the other one), and it boots fine. After almost an hour it dies again. On boot, beeps. Wait a few minutes, boots again, then dies. Beeps next time. Etc.
The 8 beeps apparently mean there is a problem with the video card. I have tested two video cards that both work fine on another motherboard, no difference.
Because it dies after a while when it has rested, I suspect some sort of overheating issue. I put a bigass fan blowing at the motherboard and video card but that didn't seem to do anything. The fan on the video card is clean.
I have hooked up the D-Bracket 2 that accompanied the motherboard. It has some lights flashing depending on what is going on, and it halts on "Early Chipset Initialization", which is phase 2 of 16 (1st being "System Power ON"). When I press the power button, the LEDs on my memory sticks flash for a few seconds (showing activity), and the D-Bracket lights up. Then the memory-LEDs go to rest (inactivity), and the D-Bracket halts. Fans keep spinning but there is no life. No beeps.
After leaving the computer off for the night, I cleared the CMOS. The computer booted and ran fine for a couple of hours, then it suddenly made a noise in the speakers, and the monitor went black. Fans still spinning. The little light at the monitor indicating that it is turned on was flashing, as it does when the computer is off and the monitor is on.
This is the hardware in my system at the moment. I have removed plenty of stuff to rule out other components but even with just this it won't work. No mouse, keyboard or other drives attached, just this.
CPU: Athlon64 3200+
Memory: Corsair TWINX1024-3200XLPRO DDR
Power: Thermaltake Purepower Butterfly 480W W0020
Output: +5V (35A), +3.3V (28A), +12V (17A), -5V (0.3A), -12V (0.8A)
Graphics: Gainward GeForce 6800Ultra 256MB GDDR3 AGP8X, "Ultra/2600 Golden S",
Motherboard: K8T Neo-FIS2R/FSR (MS-6702)
Harddrive: Seagate Barracuda IV ATA 7200 RPM
Monitor: Samsung SyncMaster 957p
Any ideas, suggestions or questions? I am stumped.

Quote
I have removed plenty of stuff to rule out other components but even with just this it won't work.
Quote
Graphics: Gainward GeForce 6800Ultra 256MB GDDR3 AGP8X, "Ultra/2600 Golden S",
Quote
+12V (17A),
If your graphics card is like mine (see sig) with two power connections at the back you may have stressed the PSU over the last year to it's final end. Borrow or buy another PSU with at least 24 amp on the 12v supply. Your current PSU with only 17 12v amps was bound to fail. Especially since you state you had other hardware at one time. CPU Graphics card, case fanes and drives are all calling on the 12v rail to power them and your PSU just might not have it any more to do the job and the highest draw is at startup.
Try another PSU.

K8t Neo-fis2r - not booting!!!

Similar Messages

Maybe you are looking for