K8T Neo-FIS2R - P20378 Sata Controller option missing in BIOS. Cannot disable

A few hairs left....& those are disappearing quickly.......!!!!
I currently have Windows XP PRo running under a Promise SATA Drive. (NO RAID REQUIRED)
In order to allow for a fallback situation (which I am still using swapping between WIN XP & Vista), I found a 20GB IDE Disk attached it to the standard IDE controller & did a clean install of VISTA ULTIMATE on the 20GB Drive...So Far so good.
Next I booted up changed the boot sequence to pickup the 20GB IDE drive first ...Vista Came up....Still so far so good.
Then I found my mouse ...& both USB printers were not recognised.....2 days later I have them all going okay....one problem at a time....
The only issue left ... I cannot see the SATA Drive attached to the promise controller.....I have tried following a few of suggested methods to load the promise drivers that are around......still no luck. Most of the posts I see are around installing VISTA on a SATA drive...my case is just seeing a SATA drive this not the O/S disk.
Moving on ...no luck with the Promise Drives ...so I have tried changing to the VIA Controller by unplugging the SATA cord from the Promise controller & plugging into the VIA Controller ... I boot up & still no luck...The BIOS picks up the VIA change as I see a option to use <TAB> to setup RAID during bootup.. I do not want RAID only a single SATA Drive. One of the things I read was to turn off Promise via the BIOS settings . The manual indicates I need to access this by going to the "Onboard PCI Controller option", here I should be able to turn off the P20378 S.ata Controller...
my problem is ...I can see only the Lan Controller as a option to disable/ enable the other options including the P20378 S.ata Controller.. are not visible.. hence I am unable to disable the Promise SATA Controller within the BIOS..... HELP pretty please..... I can happily run VISTA but I do not have 150GB visible to me & my current disk space is tight.....I need that 150GB ...........
signed...frustated NOOB
PS I have the most recent drivers/ bios etc according the MSI's Online S/W synch tool (which I run in XP Pro as the vista version fails.... DOH)
MB --> K8T NEO FISR2
Memory 1GB
Appreciate your help ..... TA

I agree with Hans, as far as we know there are no drivers for Vista to use the Promise controller, yet.
Same old, same old, Vista and no drivers.
You just have to wait and hope there wil be Vista drivers for the Promise controller.

Similar Messages

[Athlon64] MSI K8T Neo FIS2R BIOS Update when? CnQ no workie!

The MSI K8T Neo FIS2R (MS-6702) hasn't had a BIOS update since 3-4-2005!
I put a Sempron 64 3000+ in my motherboard, and was very disappointed that it is recognized as an "AMD Unknown Processor". Sure, it works, but one of the reasons I bought it is in the hopes of getting AMD Cool n Quiet to work. However, apparently the AMD driver can't recognize the CPU due to the old BIOS on the motherboard.
Every other MSI skt 754 board supports Sempron E6 revision already. Why not the K8T Neo FIS2R? Where have all the MSI BIOS programmers gone? I have been waiting 2-months for a BIOS update to support the E6 Semprons. I have asked and begged MSI Tech Support. I am tempted to switch to ASUS or some other company that is actually timely with BIOS updates. Only reason I haven't yet, is this board is everything I want EXCEPT for Cool n Quiet not working. It's starting to look like there is no BIOS update in sight, so I am very disappointed.
Anyone here work for MSI can confirm there are no plans for a BIOS update? Because I don't want to wait around for something that's not going to happen.

Sorry, I didn't mean to imply I thought the mods here are MSI staff... I was just kind of hoping there's MSI staff lurking here, seeing what people think of their products or seeing what people complain about.
No, pretty much C 'n Q is the only reason I'm disappointed, but it was something I was really set on getting to work since this is a server that's up 24/7, but isn't utilized but maybe 4hrs out of a given day. I could reduce frequency and voltage, but unlike C 'n Q, it won't automatically increase speed and voltage based on demand - which is something I want since although it's a server, I also use it as a regular PC as well.
I've even tried the 2.33 beta BIOS with no change, and even found a 5.52 BIOS in their BIOS testing directory. I guess that BIOS was for a different kind of 6702, although I had pulled out the peripheral modules with AMI's MMTOOL and they looked the same as the existing BIOS, but that BIOS killed my motherboard so it couldn't have been for a regular 6702. I had to desolder the BIOS chip with a heat gun, reprogram the old BIOS back on it with an EPROM programmer, and solder in a socket. I guess that shows my dedication to get C 'n Q working!

K8T Neo-FIS2R V1.0, CPU Speed Problem

Hi, I got a Athlon64 3500+ (NewCastle) and K8T Neo-FIS2R V1.0 MotherBoard
Just downgrade my bios from 9.2 to 3.3 since the 9.2 bios does not show the correct +3v voltage in the core center and the website is recommending that old version of Athlon should use 3.xx bios.
But the problem occurs, the core center now shows the cpu speed is 1xx rpm and keep sending alarm. I use other software to check the fan speed and it is 2xxx rpm. The temp of the cpu is between 33 to 43 'C.The temp of the case stays at 42 'C. The voltage of the CPU is 1.52-1.53V. One time, somehow the temp of the cpu went up to 50'C but the fan is not turning faster to cool down the CPU. No matter what models (Cool&Quiet or User) I choose in the core center, it just did not go faster. Finally, I have set full speed of the fan in the core center to increase the speed of the fan.
My PSU is Enermax 450W, and I used 5V for my three case fans since they are really noise.
Any problems with my system or computer, or any recommemdation?
Sorry for my English, but I am doing my best.

Everest just has no readings that work for us. They never supported our board. None of the software gets a correct read on our 3.3v so no there is no answer. I have tried them all as have others. If reading the 3.3v is that important to you use a meter.
I have yet to ever trust Core Center. It lies. Keep in mind just how many MSI products it is used in. So far it has yet to be that accurate in any Via Based MSI product. Search the forum here for it. No one seems overjoyed with CC.

MSI K8T Neo-FIS2R SATA CD/DVD Support

Does anyone know if the K8T Neo-FIS2R mobo will or can be made to support a SATA CD/DVD drive. I am having no luck so far either getting it to recognize the drive or finding any info as to such.
Any help will be greatly appreciated.
Cheers

I was able to answer my own question. I was doing a bit of searching around on the MSI website and happened across a newer bios that doesn't come up in a regular search. The regular search turns up this page http://www.msicomputer.com/support/bios_result.asp (obviously inputing the correct platform and model) showing BIOS v2.2 as the most current. But by poking around on the site a bit, I came across another BIOS page for the same mobo, http://global.msi.com.tw/index.php?func=downloaddetail&type=bios&maincat_no=1&prod_no=565 showing BIOS v7.1. I figured I'd give it a try and low and behold the bios is recognizing my SATA DVD Burner.
The hd array has to be connected to the Promise controller as it will not see the optical drive even if it is set to SATA mode. I hooked the SATA DVD burner to the VIA controller and changed the setting in the bios for this controller to SATA mode as opposed to RAID mode (this was not an option on this controller in the BIOS before the flash to v7.1). I also had to have the PATA controller set to enabled or it would not recognize the drive. It is now a recognized device and shows up as an option in the boot menu. I added an additional SATA DVD drive to the other VIA SATA connector and it recognized it right away and made it available as a boot device. I tested with Knoppix and it booted fine.
Hopefully when I try to load XP this evening, I will have a winner.
Thanks again for your replies!!!

K8T Neo - FIS2R (model 6702) SATA and RAID Problems = Hair Loss

Hi All,
new to the forum, have searched but nothing like my problem exist.
I have a K8T Neo FIS2R M/B and trying to get a single SATA HDD working for my secondary drive. primary is a IDE which works well and I want to leave it.
I have plugged in the SATA HDD into the SER 1 port ( Promise 237 ?) anyhow the bois at startup or post recognises the drive, but then says soemthing like you have set up raid before F1 for setup F2 to continue to boot.
I have pressed both f1 and F2 at various time, but it appears that it want to turn the single drive into a RAID system, which is not possible with one drive !!....
Anyhow windows XP then boots up and loads a RAID driver and also the promise RAID drivers. the real problem is that XP sits and waits for the raid which never comes and during startup on XP. it is extremely slow.
Does anyone have any ideas. I am not that computer techy as you can see by the description, but it appears that I cannot get into the RAID bios to turn it off.. I have zapped the bios to try and reset it. basically i am loosing my hair ove this.
if anyone had some step by step instructions how to prevent raid from switching on at the bios and then in XP it would be greatly appreciated
Jeff

Hi All,
Sorry for the slow reply, retrieving the box from the bottom of the swimming pool !!!
I set it to SATA as you have indicated Hans, I did check that setting. Thankyou for checking.
Spray, I have tried the P20378 setting as well. You indicate that you need to press F6 when installing the OS. I have WinXP running already on an IDE master and am trying to set the SATA up as a secondary disk drive.
As I indicated above, the machine runs slowly to the point of it being a 486 when I use either promise or Via controllers.
I have since removed the drive and are now having problems with XP on boot up/startup. The thing seems to hang or go slowly when the horizontal bar runs across under the Windows XP logo. I have turned everything off in the bios both Promise and Via. I am at a loss as to why:
1 it runs slowly with the SATA drive in ( also does not show all the auto loading icons near the clock)
2. why it hangs when I remove it and turn both SATA controllers off in the bios.
I have a feeling that I may have corrupted part of the registry playing around. Any thoughts... going bald :-)
I really appreciate the feedback so far

MOVED: K8T Neo-FIS2R SATA and Linux Question

This topic has been moved to Operating Systems.
K8T Neo-FIS2R SATA and Linux Question

Quote
Originally posted by chasmon
Hi all,
I have just setup up a brand new system but am having probelms getting it working. I want to install XP on a single Maxtor 160Gb drive.
I have my HD on Promise Ser1 and all SATA stuff in BIOS enabled. When I get to the screen I press F6 and then when promted I insert the floppy with the promise drivers on. I then get this message:
"File txtsetup.oem caused an unexpected error (4096) at line 1742 in d:\xpclient\base\boot\setup\oemdisk.c"
I can't get past this screen I have tried:
1.Drivers from the CD supplied.
2.Drivers from the MSI website.
Please help me this lot cost lots of hard earned I'm pretty gutted at the moment. I have also tried the Via chipset with no joy.
System:
Antec 380W PSU and Sonata Case
LG DVDROM 8163B
NEC DVDR/RW 2500B
Panasonic Floppy
Neo FIS2R mobo
Maxtor Diamondmax Plus 9 160Gb SATA150
Benq RF K/B & Mouse
Don't spam man! I posted something to this same question in another thread.. from you no less! Make a new thread! lol
Hijacking = bad!
Ian

K8T NEO FIS2R can't use the RAID controller....

I have this very strange issue.
As soon as I connect a harddisk to the Promise (378) controller of this board and assign it to an array, the system doesn't work like it should.
Symptoms:
- MS Windiag (a memory testing application) reports thousands of errors
- Memtestx86 causes a spontaneous reset within seconds
- I can try to install Windows, but the process never completes; during the installation everything works really really slow (partial XP installation takes over 2 hours!)
- Linux gives me a kernel panic while booting
My system specs:
- MSI K8T Neo FIS2R (bios 1.5)
- Athlon 3000+
- 2x 512MB PQI memory (tested with GEIL/Kingston/Infineon memory as well, the problem persists!)
- Radeon 9700
- Levicom PSU (34A RMS on 12V line) (also tried Enermax 460W and Antec tru power 480W)
- 2x WD Raptor 36Gb (RAID 0 array 1)
- 2x Maxtor Diamond plus (RAID 0 array 2)
- 4x optical drive
I just can't figure out what's going on here... if I don't use the onboard RAID controller everything is fine.... but I need it for my two arrays... (besides that, it should work, shouldn't it?).
Is this perhaps just a bug in the BIOS of my system? If so... MSI please resolve this issue, my computer is worthless for the time being.. :(

Quote
Originally posted by Bas
Try this version of Memtest86.
YAY! This memory tester seems to work correctly..!
If I put a single module (PQI memory) in DDR slot 1 I get loads of errors. In slot 2 and 3 they work just fine. When combining two modules, using slot 2 and 3, I still get some errors (32, all above 1000Mb)... but it's the best I can get out of my 1Gb.
Is it safe to assume that this is a compatbility issue that can be fixxed by buying some supported memory?

K8T Neo FIS2R Won't Recognize HDDs

Here’s my situation. I am not new to building computers, but new to the AMD Athlon64, MSI boards, and SATA drives.
I purchased the K8T Neo-FIS2R (601-6702-010) main board. A single 512 MB DDR memory stick is installed. The only card installed is the ATI Radeon 7500 ALL-in-Wonder video card. I cannot get the system to recognize hard drives. I have made many changes in BIOS, but have been unsuccessful.
At first, my intention was simply to take my almost new Maxtor Diamond Max Plus 9 120 GB ATA HDD and install it with the K8T Neo motherboard. The disk has been previously formatted with Windows XP Home, and has various other programs installed. It was working fine in my older system. I put this drive (properly connected to the IDE1 on mainboard), and the K8T Neo would not recognize the drive at all. In fact, all I received were messages that SATA Raid devices were missing (apparently the Promise controller complaining). Trying to deactivate the SATA controller via bios did nothing.
Next, I decided to purchase a Seagate 160 GB Barracuda SATA HDD (ST3160023AS-RK), thinking maybe then the system would at least recognize an SATA HDD. (of course a lot of this shows my naivete’ with newer SATA standards/componets/MBoards) Initially it was recognized, and I was able to use Seagate’s software to partition the drive and format it. However, after rebooting and attempting to install Windows XP, the drive was no longer recognized by the system. On the POST screen, the VIA controller does list it as master device 1 in the SATA.
Okay, here’s what I want: I want to install the Barracuda 160 GB HDD SATA as my boot drive, and take my slightly older Maxtor HDD and make it a secondary (or slave) drive. This means a mix of SATA and ATA drives. Since MSI’s documentation both in manual and the website provides no help (that I can find) on this issue, I need suggestions on what to do. The only explanation in K8T Neo manual is to create an SATA Raid array. I do not want to do this. I simply want the SATA as boot drive, the ATA as secondary (or slave) drive, and for both of them to peacefully coexist! How do I make the mainboard recognize this?

Quote
Originally posted by saat0014
Are you getting the error when you insert the disk and it looks for the drivers on the disk? Or are you getting it at the Windows installation screen. Maybe you should try using the promise drivers and hook up your drives to the promise controller. Here's how to get the Seagate drives to work on the promise controller. Promise Scroll down to where I posted and you'll find hopefully all you need. If you need help, just ask
The error is coming at the Windows installation screen. The drivers already (seemingly) load.
I have tried installing the Promise drivers, although not as you posted in the linked thread. I only have the one SATA drive... do I still need to configure it as RAID?
I'll try this today. In all my years of building computers, I've never had as many problems as I have with this system. This is so frustrating.

MSI K8T Neo-FIS2R, BIOS flash???

I'm trying to flash my bios but i get this wrong message after restart: CMOS SETTINGS WRONG, if you have built sata raid array previously, go to "P20378 sata controller" set as raid. I've tried that but it dosn't help.......what should i do???
Motherboard: MSI K8T Neo-FIS2R
Harddrives 2 x S-ATA Western Digital 250 Gb, 2 x IDE Seagate 80 Gb

i used to get that almost every time i update BIOS. I forgot the fix, but we need to know as Tiresmoke said whether u r at all using the promise. if Via serials r enough for u (which in this case they r since u only hv 2 sata hd's) then just use these and see what happens.
did u also try to load bios defaults? i think i used to do this when i get that error msg

K8T Neo-FIS2R Hard drive configuration questions

Im looking to buy this board in maybe a month or less (K8T Neo-FIS2R), and was wondering about configuring hard drives
I will get the version which has the promise controller on board, fo SATA RAID
The Plan is to get two Wetern Digital Raptor drives and put them in RAID 0 together.
however i will still have my DVD Writer, removeable hard drive bay (takes one IDE) and my current 80GB Seagate drive.
if i use the SATA RAID, do i have to use IDE3 for all the other devices, or can i just plug them into the IDE1 and IDE2 slots?
Also you are able to select SATA to boot from in bios correct? i have never done raid so have no idea how it works . and do you have to load RAID drivers or something before setting up windows?

anyone?

K8T Neo FIS2R AMIBOOT.ROM not working

Hi
Had a game crash on my system, and froze everything, so had to restart manualy - now I get the error BIOS is not installed..
I have downloaded a copy of the bios (not latest) and changed the relevant ROM file to AMIBOOT.ROM and copied to a freshly formated floppy.
I inserted the disk, held down CTRL and HOME and started the computer...
After a while of running through the messages of BIOS not installed and no SATA installed (which is correct), the floppy drive light comes on, and then after a while (afet I have released the CTRL and HOME keys) I get a message saying "Remove disks or other media, Press any key to restart" then nothing, if I press any key - it says the same thing untill I remove the floppy... and then it restarts again.
I have tried to restart using the floppy and the CTRL and HOME keys about 20 times so far - always the same result - I have even tried diferent versions of the BIOS.
Any ideas?
I only have one stick of RAM (256Kb - 333) and two IDE HD's
Many thanks in advance
GreenBoy

Hans
My Set up is as follows (from the top of my head as I am doing this form work)
K8T Neo FIS2R.
AMD 3300 745pin chip set.
1 stick of 512Mb ram (non branded - baught from Watford Electronics)
2 x 200Gb Maxtor HD's
1 40GB Seagate HD
1 DVD RW
Power 500W
Dont know what else you need...
Anyway - last night I reset the CMOS in the way you described.
Still cant find the VIA settings in the Advanced Chipset or elsewhare - but I will. urned of SATA in Intergrated Peripherals...
Anyway - what then happens, is it says it cannot boot.
I tried using a Win98 SE boot disk - and all the drivers were listed as not possible to load or something...
Any way - deciding I did not have anotehr boot disk to hand - tried Symantec Ghost - still same result.
Finaly I tried WinXP Pro, and found that this installed all the bootup files no problem at all - what was then found was that my C: partition was missing - yup boot sector had completely disapeared.
Anyway knowing that I have recent full backups og my primary drives using Ghost, I took the plunge, created a partition in the unalocated space, reformated the drive, and reinstalled WinXP... all seems ok for now... except the message regarding no BIOS - but from what you say as soon as I fing the switch I will loose that again.
The strange thing is I never used to get this message before, and do not remember setting anything up for SATA - couldnt afford the disks at the time....
Thanks for the help Hans, you have been more than gwenerouse with your time , but can you please give me some more information? (Im a bit of a Nooby at playing with BIOS etc as they scare the crap out of me! )
1) Why is the detail of my system so important? I have made no Hardware changes for approx 6 months and everything was fine untill the game crashed, so therefore, dont see why this should affect things.
2) Why did the flashing of the BIOS not work? I was following the instructions carefully - but nothing.. therefore in my Nooby mind this means there is something else wrong, stopping the flashing from working.
Again - many thanks
GreenBoy

Problem after CMOS reset K8T NEO FIS2R

Hi,
After messing around with my memory timings, I could no longer boot my system, so I decided to reset my CMOS using the jumper. After doing so, my system gets stuck at the SATA drives not detected BIOS not installed screen, and I can no longer access the BIOS. I'm fairly sure that the BIOS not installed message is in reerence to the SATA controller and not the main BIOS itself. I have tried reseting the BIOS a couple of more times with no different results. My D-Bracket reads red LED in location 1, green LEDS in 2, 3 and 4.
System:
Athlon 64 3000+
K8T NEO FIS2R
Radeon 9700 pro
Audigy 2 ZS
400W PSU
Any ideas would be welcome.
Thanks

Hi
Try removing the Ram sticks when resetting Bios, remeber to earth yourself first, also remove power cable, and leave for a couple of minse, to allow all chips to discharge, then replace mem sticks, the cmos jumper and the power cable. Try to get into bios at start to reset the timings you have changed. If still having a prob, use Ctrl + Home as you boot, holding them down will initialise the bios. You will have to reset the bios settings.
Failing that you will need to use a recovery floppy.
Good luck
jocko

K8T Neo-FIS2R wont copy drivers...

Hi all i ahve been looking through the forums for a long time now. I can find anyone with the exact problem as me. I will list my specs first.
K8T Neo-FIS2R K8T800
Seagate 160GB 7200RPM SATA Hard Drive
CORSAIR XMS Xtreme Memory Speed Series, Xtra-Low Latency 184-Pin 1GB(512MBx2) DDR PC-3200 w/ Platinum Heat Spreader
AMD Athlon 64 3400+, 1MB L2 Cache, 64-bit Processor
ATI RADEON 9800PRO Video Card, 128MB DDR, 256-bit, DVI/TV-Out, 8X AGP
Aspire 520W 12V Black Triple Fan Aluminum Power Supply
Okay heres the problem. I run the windows XP pro sp2 install cd and then i get to the screen were you press S. That works and it gives me a list and i pick the first XP one on the list. Then i press enter and it starts loading the files. At a certain point when it starts the windows setup it says that it cannot copy the following files; VIAMRAID.SYS, VIAMRAID.cat, and VIAMRAID.inf so i use the skip option. The computer runs through the copys the rest of the stuff fine then restarts like it should. When it gets to the windows loading screen it gives me a blue screen error about the HDD or something. Now i have no clue whats wrong with it there is no reason that it should not work.

Quote
Originally posted by viqu
Quote
Originally posted by Jocko
Hi
Sounds like a flakey floppy, if cable is wrong way, then the floppy led is lit all the time. Does your cable have the crossover wires to end connector, use the end of cable connector, maybe try another floppy cable, if it does use read or boot from a win98 startup disk, then it is the floppy drive or cable. Could of course be bad floppies, but not usual if you are trying several differant ones ( unless they have been beside a magnetic sourde, like telephone). I would try another cable, then another floppy drive. One or other should fix it, as your bios settings appear good.
Is the floppy shown on first page in bios setup - Standard Cmos Features.
Cheers
jocko
MSI sent me the v1.93 bios. I updated my MOBO. Now heres one question since this seagate is new and everything else is. Should i have done a full format on the HDD instead of a quick before i tried installing it. My friend is saying thats what i should have been doing instead of the quick format for partitioning.
I update ya on whats going on. Well the new bios didnt change anything. I also did full format on the HDD dudring the windows setup. It took forever to finish the format. Even after the full format it still didnt work.. I tested jockos cable theory and it did not work. And my floppy drive is show as floppy A

K8T Neo-FIS2R - raid 1 refused by Win2K

Hi,
I had K8T Neo-FIS2R for some time, working flawless. I had 1 ATA drive (Maxtor 120GB, 8MB) on a VIA controller. Then I decided to buy another similar one ATA HD, and create a raid 1 array (ATA+ATA) on Promise controler, with existing Win2K SP4 instalation.
Everything went smoothly, creation of array and image on second HD. Then reboot, Windows start loading... and suddenly BSOD. Message: "If this is your first time seeing this message...check for viruses...corrupted HD...blah blah".
Tried loading again and again - same situation.
Then I discarded array, rebooted, and created it again. Same problems. And headache & rage.
Few days later, I had a possibility to borrow a new SATA Maxtor 120GB drive, and try with ATA + SATA raid 1 combination. Done everything from the beggining, creating of array and image, at the end...again BSOD with the same message. 100% identical like in 2xATA combination.
I thought that maybe the problem is in "original" ATA HD, so i tried with another combination: second (new) ATA HD from first situation (image of original HD was still on it, but with discarded array), anda SATA from second as a "slave" (so, this one is deleted in creating of this array). Same, same, same... Needless to say, at the end I tried with SATA as "master" and ATA as "slave". No progress.
BIOS and all drivers were/are up-to-date. All HD`s work OK in a "no raid" situation, on both controllers.
I have searched this forum, but didn`t find similar problem. If you have some ideas/suggestions/solutions, you will be a hero, for saving a one young man`s life
Thanks in advance,
Buca,
Belgrade, Serbia

Quote
Originally posted by Tiresmoke
Promise ATA raid can only work though the Promise ports which in the case of ATA or Ultra ATA drives would be IDE3 port. Then you must have Promise Raid turn on in the Pheriferals menu in Bios as well as set up under the Promise Raid section that will come up directly after post.
You will need to read the Promise Ademdum manual that came along with the regular user manual for setup details.
Thanks for trying to help, but I have done that all. I can create a raid array with ATA drives only on Promise...

K8T Neo-FIS2R Old Problem, New Issue

I made my system back in 2003 using a K8T Neo-FIS2R motherboard and a Barracuda 7200 SATA 160GB drive (ST3160023AS). If you don't remember, back then motherboards that supported SATA drives for main drives, sometimes needed extra drivers in order for the windows installation process to work. At first this threw me, but since then I have reformatted my drive a few times using the same disk with no issues.
5 years of file sharing can do a number on your harddrives, and it seems my Barracuda has finally died. It came time to replace my drive with a Western Digital Caviar 320GB drive SE16 (WD3200AAKS). I did not predict there would be any issue with replacing my SATA drive. I have another 500GB drive connected to my system used for only storage and the computer recognized it at once.
So I formatted my WD HD, to NTFS and made it active. Then I installed it in my computer disconnecting my other 500GB drive. I ran windows installation with my Windows CD (which I have used many times and I keep it in pristine condition).
I found that after I hit F6, and it gave me a selection of SATA drivers to use (used xp), it did not not see that drive was there when asking which drive to format (I repeated this many times). I set about making a new SATA boot disk thinking that my pre-used one had gone bad.
http://global.msi.com.tw/index.php?func=downloaddetail&type=driver&maincat_no=1&prod_no=565
VIA VT8237(R) SATA RAID Driver (For floppy driver)
I followed the disk directions having already done it before. When I tried to install with my new drivers, I got this error.
"File\I386\NT5\viamraid.sys caused an unexpected error (4096) at line 2108 in d:\xpclient\base\boot\setup\oemdisk.c."
Now i KNOW my windows instillation CD is good, but just in case I used another windows CD and got the same error.
The only idea I can come up with is that I upgraded the bios to much and now it is having issues. My bios version is:
AMIBIOS A6702VMS V2.2 030405
SATA378 TX2plus(tm) Bios Version 1.00.103026
Does anyone have any ideas of what I can try? I have done all the easy stuff I could think off like try different cables, and plug in my SATA to the second sata port and not the first. I have run out of ideas.
The only list thing I could try was connecting my sata drive to the computer using a SATA to USB adapter, and finding the partition in windows through that way. For some weird reason windows will see USBs in the computer but not installed Sata drives. I am thinking I will install windows using the USB device and then try plugging in the drive directly. I have no idea if it will work.
Any help would be greatly appreciated.
Sombrenote

Quote from: sombernote on 11-July-08, 09:15:36
Thank you so much for your help.
I tried your two versions of your drivers, "VIA PIDE&SATA RAID.rar" "Promise 20378 S-ATA RAID.rar" neither of them worked well (I selected the "VIA RAID Controller(Windows XP"). I received a slightly different version of the last error "File\I386\NT5\viamraid.sys caused an unexpected error (4096) at line 2108 in d:\xpclient\base\boot\setup\oemdisk.c."
The (4096) was a different number.
I had used 4 different (yet old) disks, trying to get it to work. None of them did so until i tried it once more. This last time worked, it saw and used the drivers. I was able to get into the disk selection screen, and set to format the disk. As it started formatting (Quick), windows said that there was something wrong with the "Disk or CD". It then asked for me to install the SATA combo drivers. I let it detect the drivers I was using, and it kept saying something was wrong. I tried it 3 more times, and the last time it held and copied the files from the CD, to start windows.
It is obvious to me that I have either a bad disk, CD, Disk drive, or CD drive. This is quite possiblly my last format before I make my new computer. Thank you very much for your help. I would have had to start my voodoo magic tricks to get it to work.
Crappy floppy cause that
Happend to me many times as well, when you receive the error take out diskette and re-insert it, then load drivers again until works.
Of course simple solution is just replace the floppy drive to avoid "voodoo magic tricks"
Or best solution do a slipstream XP installation and integrate the drivers which you need in XP installation.
>>> Slipstreaming Windows XP Service Pack 2 and Create Bootable CD<<<
>>> Slipstreamed Windows XP CD Using SP2<<<
"Thank you very much for your help. I would have had to start my voodoo magic tricks to get it to work."
You are done well

K8T Neo-FIS2R - P20378 Sata Controller option missing in BIOS. Cannot disable

Similar Messages

Maybe you are looking for