K8T Neo-FIS2R rebate

I ordered this motherboard near the beginning of this year because it had a mail-in rebate. It's been about 3-4 months since I mailed the rebate form along with the UPC barcode and I haven't received a rebate check . Did anybody else buy this board during that time and get a rebate check?

I did receive a letter directly from MSI saying that they received my rebate and that they would be mailing it out, unless I choose to apply it to a USB MP3 pen product they sold. I had until April 5th to respond to the offer, which only gave you $20 off the product anyway, I believe. I assume they are going to mail the rebate after that date. Either way, it's still taking way too long to get it.
Shame on them for slow rebate check delivery and a "bait 'n switch"-type tactic.
I just want my $20, OK?!!
Tim

Similar Messages

Onboard 5.1 sound noisy - K8T Neo FIS2R

Hi guys, i'm new here.
Well, i got a K8T Neo FIS2R and the 5.1 sound is noisy. I've tried many different drivers, replaced my 5.1 speakers for new ones and it doesn't work properly at all. I've been using a 2.1 system and it works just fine. Has anyone seen this problem? any advice?
Thanks in advance
Kein

LOL OK you can save us time by replying to that end the next time. Thanks.
I know it may seem trivial but I can't count how many times a suggestion was assumed to have been tried and it turned out to be the fix in the end. So if we seem grouchy about getting a reply remember that we aren't the only one's that waste time chasing stuff when no one let's us know what they have tested.
OK back to your problem. There are no magic buttons to push. If you have tried other speakers and drivers then it is likely something on the MB that is causing the problem. It could be a power line somewhere close to a chip or connection, it could be a bad ground. If you have a Sound card handy you could also check it to see if the problem goes away. Otherwise you may have to RMA it.

PSU for K8T Neo-FIS2R

What model of PSU has its cooling fans which can be controlled from PWFAN1 and PWFAN2 on the K8T Neo-FIS2R motherboard?
Kaz

Sorry but there is no real specific one out there that I have ever seen. Most of the Bios options you see have been available since forever with Via Chipsetted boards. However DOT is specific to MSI which is Dynamic Overclocking technolodies. DOT can automatically overclock your voard depending one what your doing. I recommend staying away from it as it can cause as many issues as anything in your rig. And then there is Cool and Quiet which is an AMD 64 Bit CPU specific option to downclock the multipliers for the CPU during Idle Times to save energy and keep the CPU cool. Again it is not really needed.
The rest of the stuff you can use google to find individually or by searching for Award Bios's or Via Chipset Bios settings.
These are way to much for any one person to post a complete guide to here as all the info is readily available elsewhere.

Should I flash the bios? K8T NEO FIS2R

Ok... I have a K8T NEO FIS2R mobo. A couple of friends of mine have been telling me to flash the bios to the most current version... Then some other people have been telling me that it is too risky and I should hold off untill something goes wrong that I know a bios flash can fix...
I'm just wondering what is the concencious here... should I flash it, or should I stay with the current version I have now(the one that came with the mobo) I Like to have my computer as up to date as possible, but all the reports of bad flashes have me a little worried. This is a procedure that I have never done before, and I dont want to mess it up.
If I should flash, Any insight, tips, tricks, special instructions, etc... would be greatly appriciated.
Thanks!
Magnum

Thanks guys for the quick responces... I'm used to not getting a responce from forums for 12-24hrs and here it is less than 24hrs later and I have 10 responces.
I'm not at my computer in question right now, but I am almost positive that my bios is ver1.0. Same one that came with my mobo.
At this point I am leaning towards flashing... If basically the only way to mess it up is to have my power fail, then I dont think I will have a problem. I'll just borrow an UPS from work here to be on the safe side.
hypothetically if i follow the instructions to a tee(windows flash/live update) are there any other ways it can mess it up? I just want to get a hold on all the places where I could mess it up.
Will live update take me all the way through the procedure, or do I need a separate set of instructions to read off of during the flash?
Also what gear will I need... floppy disk? anything else?
Sorry about all the questions, just want to make sure I do this right the first time!
Thanks!
Magnum

6600GT not working with K8T neo-FIS2R

I recently returned a K8T NEO-FIS2R MB for repair. The problem was that the PS/2 and USB ports were broken. However the MB has been returned and the PS/2 and USB ports work fine. I posted about this several months ago.
Now the AGP port seems to be broken (not the actual slot). I have tried a 6800 Ultra and a 6600 GT (AGP version) GFX card in this slot. Both cards fail at the driver installation point. I have tried driver versions 66.93, 67.02 and 67.03. I also tried 3 versions of the via drivers 451, 453 and 455. Even tried XP with SP1 and SP2. The PC will sometimes BSOD, reset, won't boot into windows. The drivers sometimes install then other times they won't, etc. The problems only seem to be with the drivers for the GFX cards.
The 6600 GT works as I have tried it in another MB without any problems.
I know the memory works fine as I used memtest86+ for a couple of hours on the default settings without any errors and it works in another PC.
The spec of the PC is:
XP pro
K8T NEO-FIS2R MB
512MB corsair XMS at 2.5-3-7-3
XFX 6600GT
40gig HDD
FDD
Plextor CD writer
DVD Rom
PSU is a Q-tec 550W
I know Q-tec PSUs are not up to much from what I have read elsewhere in this forum, but I have had it running in a similar system with the 6800 Ultra installed without any trouble (even with the above MB before it went faulty). I have also tried a 400W PSU, that came with the case. The Voltages on the 12V line are between 12.00 and 12.03 when using the Q-tec PSU.
Has any body else had these problems with the 6600GT in the mentioned MB.
Also, how can I check the serial number on the MB with the label on the box, as this MB that was returned to me looks to “clean” to be the one I sent away for repair.
Thanks for any help

Hey, I'm glad to see a post on the new Gforce 6600GT AGP card. I just recently put together a brand new system (see my sig for specs). System runs great. The only thing I wanted to do was replace the video card, and after a great deal of anxiety I decided the Geforce 6600GT AGP was the best bang for the buck.
Well I got home, installed the card and never get passed the bios screen. (shows your processor, memory, memory siz), the screen u hit DEL to go into the bios.
The system doens't lock up, NUM LOCK can still be turned on and off, and CAPS can be turned of and on... but thats it. Just sits on that screen. I can't go into the bios either.
what settings do I need to do prior to isntalling this card to get it to work.
Let me know if you all need anymore details to help me out.
oh, I did reset my frequency to 10x200 (which is what I think the 3000+ is supposed to be at).

K8T Neo-FIS2R - 3200+ - Mushkin Level 1 RAM: Optimal Memory Settings

Just got a K8T Neo-FIS2R with a AMD Athlon 64 3200+ with 1g (512MB X
2) Mushkin Level 1 PC3500 RAM as recommended by Anandtech on his High
End System roundup:
www.anandtech.com/guides/showdoc.html?i=2041
I am having a HUGE problems with memory settings in the BIOS.
On AUTO, the memory is only autodected at DDR200, which I found odd.
I them took memory setting in my old hands and things don't seem much
better:
I made these changes:
MEMCLOCK: DDR400
BANK INTERVEAVING: AUTO
BURST LENGTH: 8 BEAT
CL: 2
TRCD: 3
TRAS: 5
TRP: 2
This was unstable at first and bumped the DDR Voltage to 2.7, moved
the sticks to DIMM1 and DIMM3 (instead of DIMM2), and it seems stable,
but not very fast. according to Sandra Scores
Any recommendations for Memory Settings? Why would the MB not
autodecte DDR400 RAM? I am not looking to overlock...just maximize
the CPU and memory I have.
Maybe I just need to get new memory. What is the best memory for this motherboard?
Thanks,
Steve

I'm running the same mem (see my sig). Since its PC3500 I attempted to tighten the settings to those you had listed (2,3,2,5). It was not Prime95 torture test stable at even the stock 200 MHz FSB using these settings. Upping the voltage to 2.7 did not increase the stability in my system at these settings. The memory ran perfectly at AUTO settings, but was clocked at 2.5,3,3,8 I believe.
Keep in mind that level 1 is advertised at 2,3,3. My system is 100% stable at 2.7V for me up to 210 MHz FSB at these settings (I haven't tried any faster). My TRAS is set to 6.
Hope this helps a fellow Mushkin user

K8T Neo-FIS2R latest mobo revision

Hi
I am wondering does anybody know wich is latest mobo revision for K8T Neo-FIS2R.
Mine mobo revision is 1.0

wow after standing on my head i found it mine says 02
i am thinking this isnt too helpful as for all i know that is the month it was built..or the inspector number,...
but it was fun trying to find it..a red sticker on a red board
i should have figured it would be near the revision number.

K8t neo fis2r - core center not functional after installing sound card

Hi. I had been using Core Center with Dynamic Overclocking enabled and all was well. When idle, my amd64 3000+ (2.0ghz), was running at 800mhz. Under load it would go up to 2100mhz. But yesterday, I installed an Auzentech x-plosion sound card and after i installed the driver, the dynamic overclocking stopped working, my cpu is running at max all the time. (The variable fan speed function still works).
I checked the IRQ and there is no conflict, I uninstalled the amd64 driver and core center and reinstalled. Still does not work. I uninstalled the auzentech driver, rebooted, and cancelled new hardware wizard. Then the variable cpu frequency feature worked. Once I install the driver for the auzentech, dynamic oc stops working. I was thinking to try another pci slot but it appears to be a software issue rather than a hardware issue. The new version of Core Center does not work with my board even though msi says it's compatible so I'm still using the one that always worked. The amd driver is the latest and also always worked.
Has anyone else had a similar problem, perhaps using the auzentech sound card with this board and Core Center? Or does anyone have any suggestions?
Thanks!
K8T Neo FIS2R
AMD64 3200
AMI bios version 2.2
1.5Gb pc3200 memory
nvidia quadro FX 1100 128mb AGP
Antec 430W ps

Hey guys, I just went to AMDs site to get the dashboard utility mentioned and in the readme, it stated that in XP, the power option needs to be set to portable/laptop. But in the past, I read that it needed to be set to "always on" and that it is, in fact, what I had it set to before when cool n quiet was working. Now I change it to "portable/laptop" and it works and set to "always on" doesn't work anymore. So now Core Center reports I'm at 33c @800mhz at no load. I don't get it??? I'll have to try an alternate utility just to verify that is indeed working.
btw, QV, I checked system properties, (right-click my computer > properties, or "system" in control panel) and on the "general" tab, it indicates an AMD64 3000+, 2.0GHz. But I'm pretty certain the clock frequency is dropping now as reported by core center because of the decrease in the cpu temp at idle. Am I looking in the right place in XP? I have XP pro, SP2
Again, thanks for the input and Happy New Year

Msi k8t neo fis2r problems part 3

sometimes when the computer is turned on it just turns the fans and leds on but doesnt boot up...
most of the time it loads up and i boot to the windows xp cd and i install the drivers for sata and then when it reaches the point of copying the files it will give me a bsod and say that there is a problem with the irql driver and then force me to shut the pc down..
sometimes it makes it past that and will begin to copy files onto the hard drive, like somehow the data is becoming corrupted..however it will start to say that the files cant copy randomly and it will allow me to retry..they will copy the 2nd time usually..i can keep hitting retry and it will usually go by..it gets to 30 something % and then crashes to bsod just giving me some random error..for some reason the files keep screwing up that go on the sata drive....I just replaced the old power supply that wasnt working with an antec true watt 430 watt power supply, so i know it isnt that..
i just cant figure out what the heck is going on..any help would be appreciated.my specs are
"IRQ NOT EQUAL OR LESS"
athlon 64 3000+ cpu
msi k8t neo fis2r motherboard
mushkin special cas 2.0 2-2-2-5 512 mb pc 3200
western digital 8mb cache 80 gb sata hard drive
sapphire radeon 9800 pro 128 mb 8x agp

fyi look an your cd sticker ity will show power, consumption, but they are way lower than you would think, hard drives,can be only 10 watts, less then some case lights , and fans, cd are similar.. your video, is the biggy somewhere between 90~150 watts..yikes .next to the cpu..and the mobo can use 50 or so (not sure about new mobos) not to mention the ram 1024 is @40 watts or so., dont forget about 25watts per pci card, not counting the sound card which can be double....
ergo the need for a big psu..
the combined total ratting on a psu is not the max number that the psu is rated, that is surge value.. so a 500 may only hold 400 sustained , and that will drop as the machine heats up, so in the end your 500 may onlyy pull 366 @50'c...

MSI K8T NEO FIS2R No VGA help plz!

Hi, ive just purchased a new athlon 3000 64 cpu retail and an msi k8t neo fis2r motherboard, the specs and problem are below but plz bare in mind i am a system builder for the last 3 years i have tried alot of things to solve this.
MSI K8T NEO FIS2R MOBO
AMD 3000 64 RETAIL CPU
AMD RETAIL HSF
1024MB DDR333 SAMSUNG RAM
120 GIG WD HD
GALAXY GLACIER GEFORCE 6800 GT 256MB
PIONEER 106 DVD WRITER
400 WATT PSU (TSUNAMI I THINK)
Anyway the problem is this when i put the system together and turned it on i dont get any vga the monitor just says NO SIGNAL and when i look at the graphics card the fan on it isnt spinning.
Yet i have my old setup which is as follows,
ASUS A7N8X DELUXE MOBO
AMD 3200XP BARTON
AMD HSF
1024MB DDR333 AMSUNG
120 GIG WD HD
GALAXY GLACIER GEFORCE 6800 GT 256MB
PIONEER 106 DVD WRITER
400 WATT PSU
Basically the same as above i just changed the cou and mobo now when the graphics card is in that system it works fine no problems as soon as i try it in the new a64 system it doesnt work the fan doesnt spin and nothing comes on screen, ive tried everything i know ive double and trebble checked connections and ive tried removing components and then trying it, no matter what the graphics wont work.
I figured the motherbaord must be faulty and am going to contact the place i got it from but it would be good if anyone here knows how to solve it if it isnt the motherboards fault.
thanks very much.
ic3man1999.

Thanks guys, huess what like an idiot i forgot to put the 4 pin 12v in :( doh
Anyway it works fine now, but i have high temps core centre says 56 degrees right now while im typing this ? is this accurate or am i in trouble ?
Oh yeah and everytime i load windows it says new hardware found ide channel then secondary ide channel then it says a problem occured during your new hardware installation and it calls the hardware HDC it says this twice aswell.
ANy help guys ?
thanks

Calling all old MSI K8T Neo-FIS2R users

Ops i posted this in the wrong forum first time, this is the right place
This for all MSI K8T Neo-FIS2R users, that have changed to the new MSI K8N Platinum nForce3 250 mobo, if I have the chance to swap to the new board should I do so, or does this mobo have its fair share of problems?
Is the MSI K8N Platinum nForce3 250, a better board compared to the old MSI K8T Neo-FIS2R? Not taking into account overclocking.
Like is the onboard sound the same or worse or better in your opinion? Is it any faster at stock? Are there any other advantages?
Thx Xe

I had a K8T Neo Fis2r at first. I got a K8N Neo because I believed my Blue Screens were a faulty K8T Neo. As it turned out, the Audigy2 I had in there was the problem, because I still got Blue Screens with the K8N Neo, and when I took out the audigy and used onboard my system ran stable.
I havent had any of the apparent keyboard controller problems, or ANY other problems with the K8N. My only instabilities have been the Audigy2's fault.
Havent tried overclocking on the K8N Neo yet, maybe a little down the road. As far as features go, the K8N has the hardware firewall on it (which I dont use) but apparently its "true" gigabit ethernet is better than the K8Ts. Dont ask me to clarify that, lol
btw Got my turtle beach Santa Cruz today and put it in my K8N Neo, crossing my fingers... =\

K8T Neo-FIS2R Hard drive configuration questions

Im looking to buy this board in maybe a month or less (K8T Neo-FIS2R), and was wondering about configuring hard drives
I will get the version which has the promise controller on board, fo SATA RAID
The Plan is to get two Wetern Digital Raptor drives and put them in RAID 0 together.
however i will still have my DVD Writer, removeable hard drive bay (takes one IDE) and my current 80GB Seagate drive.
if i use the SATA RAID, do i have to use IDE3 for all the other devices, or can i just plug them into the IDE1 and IDE2 slots?
Also you are able to select SATA to boot from in bios correct? i have never done raid so have no idea how it works . and do you have to load RAID drivers or something before setting up windows?

anyone?

Motherboard Monitor settings for MSI K8T Neo-FIS2R

I'm new to motherboard monitor and there are no predefined settings available for the MSI K8T Neo-FIS2R.
Anyone help me with the appropriate settings to monitor temps and fans?

Lunchbox,
Yeah I can do that - but I'm not confident of the settings or readings. For example - the CPU temp Is only sort of correct if I set it to sensor Winbond 2 2N3904. But after displaying what I believe is correct for a few seconds it changes to something ridiculous like 7C. I've tried all the other board sensors listed and they either say my CPU temp is 118C or 7C. System temp seems to work, but again I'm not sure. Hence my post here.
It is also odd that CoreCenter and MBM disagree about a few things. Like the +12.00 rail Corecenter says 12.00v and MBM says 12.22V. Or Fan 1 that is easly 2X what corecenter says.
And if you run CoreCenter WHILE running MBM all kinds of wierdness happens - like CPU temp fluctutating wildly or CPU fan speed synchronizing and then not.
Plus clock speed is a consistent 2001 with CC and 1998 with MBM.
So I want someone who knows what they are doing to do the configs - clearly that's not me.

Fastest CPU K8T Neo-FIS2R?

Until I build my next box, I was going to try and pry a little more life out of the old one! Just bought a new vid card (thanks to suggestions from you guys!), and I was thinking of getting more RAM, and possibly a faster CPU as well.
I already have some good ideas on the RAM front, but what's the fastest CPU that'll work with the K8T Neo-FIS2R?

Here is the link to the cpu support page.
http://global.msi.com.tw/index.php?func=prodcpusupport&prod_no=565&maincat_no=1#menu

Will Gainward 6800GT fit my MSI K8T NEO FIS2R?

Horror picture on a ABIT NF7-S
I saw this picture and saw that the card i extremely long!
Anyone here on the forum that can guarantee that my Gainward 6800GT card (with a red gainward cooler) will fit on my MSI K8T NEO FIS2R?
MSI K8T NEO FIS2R
Please?

I think I have found out the problem
Using my old Enermax (350) I was able to boot up the AMD 64 2800 every time but the PSU made this weird electrical sound - I think because it was being overloaded (I think as it doesn't make this sound when used with my XP 1800). I then reverted back to my new X-Pro (460w) and after a few attempts I managed to get the ram module and CPU powered... slowly adding more fans it became harder to boot and eventually the GPU fan wouldn't run once I plugged another fan in... I'm guessing this is because my PSU is too weak to power the juice guzzling AMD
I'll need to break the bank once again I suppose

K8T Neo-FIS2R rebate

Similar Messages

Maybe you are looking for