K8t neo fis2r system help

hello.
i've been building a new system for a while, have had a doa psu to replace and now it's back the system won't post. the power comes on and everything whirrs into action but the (crt)monitor stays on standby. the mobo didn't come with a d-bracket from the supplier so i'm in the dark as to what's going on. When i forgot to replace the ram the system beeped 3 times but that's all the interaction it's giving me.
the system stats are the ones lysted below, only using 1 dimm for tests and have been trying a geforce2mx as well.
any ideas as to the fault of the system?
cheers

Hi
Thats the $64000 question.
If your sure - very sure- the PSU is OK, then next stop is ram, pity you don't have a D bracket, it should be supplied. It is a new Mobo?
All you can do is check each stick on its own in each dimm slot. But as the RAM retains info, the system needs ' discharged' before you can be sure. One easy way to 'reset' the Ram is to use another stick of differant properties, ie. DDR2100 or 2700. If none available, try removing RAM, remove power cable first, and be careful of static it can kill your ram in a sec. Earth yourself to case before touching it. Cmos jumper on pins 2 + 3, remove Vid card, all drives and fans. leave for 10 mins or more. Replace cmos jumper on pins 1 +2. use differant ram if you can. then replace HDD, Floppy, and Vid card. Cpu fan and 20 and 4 pin square connectors. Try to post, if it works, put keyboard and mouse in.
Cheers
jocko

Similar Messages

K8T Neo-FIS2R System Temp

I'm sorry if this is covered in an FAQ somewhere, but I didn't see it, and I really could use some help. When I play games with my PC case closed, I sometimes get a brief blue screen, then shut down. I believe this is because of overheating because it ONLY happens with the case closed, with the fans not running at full speed (I can run the fans at full speed, but the thing sounds like a hair dryer).
I have new case fans, and a Zalman CPU cooler on order.
But when I check my temps with something like CoreCenter, Speedfan, or Sensors View, the highest temp is always my System temp. Even under low load it's nearly 10 degrees C above everything else.
So my questions are a) could someone actually describe what the "system" is (I know what the CPU, Northbridge, etc are - I built the thing!), and b) let me know if there's some way to cool this specific component or set of components.
Thanks in advance for any help or info you might provide.

The thing is your PSU has only 24A.
However, there have been a lot of those Antec TP's that couldn't do that and where just able to do <20A tops.
The only way find out is check it against a way more powerfull one and see if it solves it.
Typicaly when this happens it has one of two problems:
1 PSU not stable enough
2 Videocard overheating
Watts on a PSU mean nothing, it's the amps that they can do.
We have found in the past (not saying you have this) that the Antec TP550W wasn't anywhere near it was supposted to do.
If you have one of those, it could be your problem.

MSI K8T NEO FIS2R No VGA help plz!

Hi, ive just purchased a new athlon 3000 64 cpu retail and an msi k8t neo fis2r motherboard, the specs and problem are below but plz bare in mind i am a system builder for the last 3 years i have tried alot of things to solve this.
MSI K8T NEO FIS2R MOBO
AMD 3000 64 RETAIL CPU
AMD RETAIL HSF
1024MB DDR333 SAMSUNG RAM
120 GIG WD HD
GALAXY GLACIER GEFORCE 6800 GT 256MB
PIONEER 106 DVD WRITER
400 WATT PSU (TSUNAMI I THINK)
Anyway the problem is this when i put the system together and turned it on i dont get any vga the monitor just says NO SIGNAL and when i look at the graphics card the fan on it isnt spinning.
Yet i have my old setup which is as follows,
ASUS A7N8X DELUXE MOBO
AMD 3200XP BARTON
AMD HSF
1024MB DDR333 AMSUNG
120 GIG WD HD
GALAXY GLACIER GEFORCE 6800 GT 256MB
PIONEER 106 DVD WRITER
400 WATT PSU
Basically the same as above i just changed the cou and mobo now when the graphics card is in that system it works fine no problems as soon as i try it in the new a64 system it doesnt work the fan doesnt spin and nothing comes on screen, ive tried everything i know ive double and trebble checked connections and ive tried removing components and then trying it, no matter what the graphics wont work.
I figured the motherbaord must be faulty and am going to contact the place i got it from but it would be good if anyone here knows how to solve it if it isnt the motherboards fault.
thanks very much.
ic3man1999.

Thanks guys, huess what like an idiot i forgot to put the 4 pin 12v in :( doh
Anyway it works fine now, but i have high temps core centre says 56 degrees right now while im typing this ? is this accurate or am i in trouble ?
Oh yeah and everytime i load windows it says new hardware found ide channel then secondary ide channel then it says a problem occured during your new hardware installation and it calls the hardware HDC it says this twice aswell.
ANy help guys ?
thanks

Msi k8t neo fis2r wont post plz help

I recently updated my bios for the motherboard, and now I can't get the pc to post. Before I had the pc going but it kept getting gpfs and crashing to the desktop from games..
I was having problems with it not wanting to post before but I raised the voltage to my ram and fixed that, the problem is that when the bios got wiped from the upgrade it lowered the voltage on the ram..now i just cant get it to post at all..if anyone has any suggestions on how to get this powered up so i can change the voltage again please let me know
I am only using one ram chip...
my specs are
athlon 64 3000+
512mb mushkin special
sapphire radeon 9800 pro
msi k8t neo fis2r mboard
antec 430 watt 12v - 20a
i cant afford a new psu and i know this one is ok as my friend tested it in his identical system for 24 hours ..
my mboard just seems to refuse to post ..i upgraded my bios and the voltage dropped because the update sets the defaults back to default..
after i upgraded the bios, it posted once, i was in the bios and i saved some settings and restarted..i was going to go back and up the voltage on the ram again so that it would post (i had solved my problem similar to this earlier by upping the ram voltage to 2.75) but it was too late and after it shutdown it wouldnt turn back on
also, ive tried all 3 ram slots with the chip, and ive cleared the cmos with the jumper 3 times..

your complete specs may help .. if running two sticks of ram you could remove one stick ... you could also reset the bios using the clear CMOS jumper .. but without more detailed specs ppl will struggle to help you

Help! XP install problems with K8T Neo-FIS2R

The other day I put together a new system for a friend. I got the system to POST properly, the diagnostic lights on the D bracket are fine, and I can edit the BIOS, and the BIOS sees all the drives properly.
However, installing XP Pro has been impossible. I set the system to boot first to the CD, then to the hard drive (from the BIOS). After booting to the CD, I never see the message I am used to seeing ("Press any key to boot from CD...) when booting from the XP Pro install disk. The system thinks about things for a long time with a blank screen, then later it finally begins to do the install. Things appear normal at this point as in any other time I have installed XP Pro. I reformat the hard drive to start clean and then the XP install files are copied over. I get the standard message that the system will reboot and this is where things get flaky. The system reboots, but I never get the message once again on whether or not to boot from the CD. So after a while the system tries to install XP once again (it would repeat this process forever....trust me). I've popped the CD out right after the system reboots so it will try to go to the hard drive. I just get some kind of boot failure message and to insert the bootable media or whatever. I've even gone into the BIOS right after the reboot to switch the BIOS loading to try and load the hard drive first. This still doesn't give me the desired results.
This is by far the weirdest thing I've ever experienced when doing an install. I've installed XP Pro on at least 15-20 desktops/laptops of different configs and never ran into this before.
The BIOS settings are stock. I didn't see anything in there that was really needed tweaking or that hadn't "set itself". I haven't messed with the SATA or RAID stuff since it's not really necessary in this situation.
Here are the system specs:
--Antec 430 True Power PSU
--K8T Neo-FIS2R mobo
--AMD 3000+ 64 bit CPU
--40GB Maxtor HD (master on IDE1)
--Lite-On DVD-ROM drive (slave on IDE1)
--80GB Western Digital (8MB buffer) (master on IDE2)
--Sony DRU510A DVD-RW (slave on IDE2)
--(2) Kingmax 184 Pin 512MB DDR PC-3200 Model# MPXC22D-38
--ATI 9800 Pro
--3.5 Floppy
All the components except the mobo, CPU, and memory are from another AMD system that was running fine. No problems with any of the HD's or the optical drives. All new components were purchased from newegg.
I thought that maybe I had a problem with the jumpering of the drives so I messed with those in about every possible combination. I took IDE2 completely out of the system and just tried to get it running with the 40GB Maxtor and the Lite-On drive. I tried about every master/slave/cable select combination but nothing was working. In certain combinations the BIOS recognized everything as I intended. I've pulled everything off that doesn't need to be connected. Keyboard, monitor, and internal components are the only things connected.
I don't consider myself to be a guru at this business, but I can get through most things with enough trial and error. This really has me stumped.
Any help is certainly appreciated.
Thanks,
Heath

Quote
Originally posted by chasmon
Hi all,
I have just setup up a brand new system but am having probelms getting it working. I want to install XP on a single Maxtor 160Gb drive.
I have my HD on Promise Ser1 and all SATA stuff in BIOS enabled. When I get to the screen I press F6 and then when promted I insert the floppy with the promise drivers on. I then get this message:
"File txtsetup.oem caused an unexpected error (4096) at line 1742 in d:\xpclient\base\boot\setup\oemdisk.c"
I can't get past this screen I have tried:
1.Drivers from the CD supplied.
2.Drivers from the MSI website.
Please help me this lot cost lots of hard earned I'm pretty gutted at the moment.
System:
Antec 380W PSU and Sonata Case
LG DVDROM 8163B
NEC DVDR/RW 2500B
Panasonic Floppy
Neo FIS2R mobo
Maxtor Diamondmax Plus 9 160Gb SATA150
Benq RF K/B & Mouse
Download the drivers from MSI again, and when you copy the contents of the XP folder to floppy ADD the file txtsetup.oem from the directory above that folder. Worked for me..!
Ian

Msi k8t neo fis2r help

hello. in need of a little hand here.
board won't post.
i've just thrown together my new system with monitor and power cable plugged in:
64 3200+
k8t neo fis2r
crosair ev ddr400
his radeon 9800 pro ice-q
tagen 480w psu
when turned on the fans all start and the power led flashes on and off slowly. screen never displays.
mobo never came with d-bracket so i can't diag the problem myself, scared it's a cpu prob.
cheers
NIB

so far all i've only wanged in the items listed (512 of the ram) and i have connected the additional 4-pin, although thanks for the mention - it's always the stupid that i end up overlooking. I've noticed that when the psu is plugged into some older p3 & p4 systems their bios' don't post. think there's a problem with the psu, although it claims to be 24a at 12v.
Cheers
NIB

MSI K8T Neo-FIS2R - help please :(

When i first got this board + my Athlon 64bit 3200+ I just left everything in bios at default, and counter-strike bullet registration was amazing, the FSB clock said 133, (no i did not imagine this as ive had two of these boards and they both said 133fsb when i went to bios).... one day my p.c wouldnt boot up, i did a series of tests and couldnt find what was wrong, i eventaully reset cmos and still it would not boot up properly. So i got a new harddrive and that seemed to solve the problem, only this time when i went to bios instead of the FSB saying 100-280, it said 190-280, now counter-strike bullet reg has totally gone and plays like , oh sure good frames per second but it doesnt feel instant, i want 133fsb back quite desperately, i was hoping one of you kind people could tell me if theres fsb jumpers on my board or how i can get 133fsb back, wont let me below 190 at the moment :(
Thanks

below are my specs,similar to yours. the issue is in the audigy card .. remove it , try a different card ( live ) if some one can resolve this please let me know too..
I have a problem ,when ever I boot my system hangs ( at sound card) ,if I power down and reboot a few seconds later its fine.if I leave it running its fine,only on a cold start. if I remove my audigy card this problem goes away, I can use other cards ,but not the audigy, did you ever have this issue ,or know any one who has had an irq issue like this( I think its in the irq) ...............
My system- Athlon 64 3400+ bios 1.4| MSI K8T NEO-FIS2R | Kingston HyperX 1GB(pc3200)@2-2-2-5 | Nvidia g3 ti500 | Maxtor 160gb SATA 160gb | Creative Audigy | Plextor 52x24x52x CDRW | | Windows XP Pro Retail | Thermaltake 3000A Case & 480w PS | NEC FE1250+ Monitor

6600GT not working with K8T neo-FIS2R

I recently returned a K8T NEO-FIS2R MB for repair. The problem was that the PS/2 and USB ports were broken. However the MB has been returned and the PS/2 and USB ports work fine. I posted about this several months ago.
Now the AGP port seems to be broken (not the actual slot). I have tried a 6800 Ultra and a 6600 GT (AGP version) GFX card in this slot. Both cards fail at the driver installation point. I have tried driver versions 66.93, 67.02 and 67.03. I also tried 3 versions of the via drivers 451, 453 and 455. Even tried XP with SP1 and SP2. The PC will sometimes BSOD, reset, won't boot into windows. The drivers sometimes install then other times they won't, etc. The problems only seem to be with the drivers for the GFX cards.
The 6600 GT works as I have tried it in another MB without any problems.
I know the memory works fine as I used memtest86+ for a couple of hours on the default settings without any errors and it works in another PC.
The spec of the PC is:
XP pro
K8T NEO-FIS2R MB
512MB corsair XMS at 2.5-3-7-3
XFX 6600GT
40gig HDD
FDD
Plextor CD writer
DVD Rom
PSU is a Q-tec 550W
I know Q-tec PSUs are not up to much from what I have read elsewhere in this forum, but I have had it running in a similar system with the 6800 Ultra installed without any trouble (even with the above MB before it went faulty). I have also tried a 400W PSU, that came with the case. The Voltages on the 12V line are between 12.00 and 12.03 when using the Q-tec PSU.
Has any body else had these problems with the 6600GT in the mentioned MB.
Also, how can I check the serial number on the MB with the label on the box, as this MB that was returned to me looks to “clean” to be the one I sent away for repair.
Thanks for any help

Hey, I'm glad to see a post on the new Gforce 6600GT AGP card. I just recently put together a brand new system (see my sig for specs). System runs great. The only thing I wanted to do was replace the video card, and after a great deal of anxiety I decided the Geforce 6600GT AGP was the best bang for the buck.
Well I got home, installed the card and never get passed the bios screen. (shows your processor, memory, memory siz), the screen u hit DEL to go into the bios.
The system doens't lock up, NUM LOCK can still be turned on and off, and CAPS can be turned of and on... but thats it. Just sits on that screen. I can't go into the bios either.
what settings do I need to do prior to isntalling this card to get it to work.
Let me know if you all need anymore details to help me out.
oh, I did reset my frequency to 10x200 (which is what I think the 3000+ is supposed to be at).

K8T Neo-FIS2R - 3200+ - Mushkin Level 1 RAM: Optimal Memory Settings

Just got a K8T Neo-FIS2R with a AMD Athlon 64 3200+ with 1g (512MB X
2) Mushkin Level 1 PC3500 RAM as recommended by Anandtech on his High
End System roundup:
www.anandtech.com/guides/showdoc.html?i=2041
I am having a HUGE problems with memory settings in the BIOS.
On AUTO, the memory is only autodected at DDR200, which I found odd.
I them took memory setting in my old hands and things don't seem much
better:
I made these changes:
MEMCLOCK: DDR400
BANK INTERVEAVING: AUTO
BURST LENGTH: 8 BEAT
CL: 2
TRCD: 3
TRAS: 5
TRP: 2
This was unstable at first and bumped the DDR Voltage to 2.7, moved
the sticks to DIMM1 and DIMM3 (instead of DIMM2), and it seems stable,
but not very fast. according to Sandra Scores
Any recommendations for Memory Settings? Why would the MB not
autodecte DDR400 RAM? I am not looking to overlock...just maximize
the CPU and memory I have.
Maybe I just need to get new memory. What is the best memory for this motherboard?
Thanks,
Steve

I'm running the same mem (see my sig). Since its PC3500 I attempted to tighten the settings to those you had listed (2,3,2,5). It was not Prime95 torture test stable at even the stock 200 MHz FSB using these settings. Upping the voltage to 2.7 did not increase the stability in my system at these settings. The memory ran perfectly at AUTO settings, but was clocked at 2.5,3,3,8 I believe.
Keep in mind that level 1 is advertised at 2,3,3. My system is 100% stable at 2.7V for me up to 210 MHz FSB at these settings (I haven't tried any faster). My TRAS is set to 6.
Hope this helps a fellow Mushkin user

Motherboard Monitor settings for MSI K8T Neo-FIS2R

I'm new to motherboard monitor and there are no predefined settings available for the MSI K8T Neo-FIS2R.
Anyone help me with the appropriate settings to monitor temps and fans?

Lunchbox,
Yeah I can do that - but I'm not confident of the settings or readings. For example - the CPU temp Is only sort of correct if I set it to sensor Winbond 2 2N3904. But after displaying what I believe is correct for a few seconds it changes to something ridiculous like 7C. I've tried all the other board sensors listed and they either say my CPU temp is 118C or 7C. System temp seems to work, but again I'm not sure. Hence my post here.
It is also odd that CoreCenter and MBM disagree about a few things. Like the +12.00 rail Corecenter says 12.00v and MBM says 12.22V. Or Fan 1 that is easly 2X what corecenter says.
And if you run CoreCenter WHILE running MBM all kinds of wierdness happens - like CPU temp fluctutating wildly or CPU fan speed synchronizing and then not.
Plus clock speed is a consistent 2001 with CC and 1998 with MBM.
So I want someone who knows what they are doing to do the configs - clearly that's not me.

Wrong multiplier k8t neo-fis2r

Just recently finished setting up my new computer and I noticed that CoreCenter is telling me that my system is at 200x5
Im using,
mobo: k8t neo-fis2r
and cpu: Athlon 64 2800+ Newcastle running at 1.5v
updated to version 2.2 of the bios
os is Windows 2000 pro sp4 and SuSE Linux 9.2 pro(main os)
I'm pretty sure it's supposed to be 200x9. I've read that the multiplier can't be changed in my bios, if true is there any other way to change the multiplier?
any help is appreciated,
Shawn

whoops just figured out my own problem....it had to do with cool and quiet....sorry to bother

MOVED: K8T Neo-FIS2R SATA and Linux Question

This topic has been moved to Operating Systems.
K8T Neo-FIS2R SATA and Linux Question

Quote
Originally posted by chasmon
Hi all,
I have just setup up a brand new system but am having probelms getting it working. I want to install XP on a single Maxtor 160Gb drive.
I have my HD on Promise Ser1 and all SATA stuff in BIOS enabled. When I get to the screen I press F6 and then when promted I insert the floppy with the promise drivers on. I then get this message:
"File txtsetup.oem caused an unexpected error (4096) at line 1742 in d:\xpclient\base\boot\setup\oemdisk.c"
I can't get past this screen I have tried:
1.Drivers from the CD supplied.
2.Drivers from the MSI website.
Please help me this lot cost lots of hard earned I'm pretty gutted at the moment. I have also tried the Via chipset with no joy.
System:
Antec 380W PSU and Sonata Case
LG DVDROM 8163B
NEC DVDR/RW 2500B
Panasonic Floppy
Neo FIS2R mobo
Maxtor Diamondmax Plus 9 160Gb SATA150
Benq RF K/B & Mouse
Don't spam man! I posted something to this same question in another thread.. from you no less! Make a new thread! lol
Hijacking = bad!
Ian

K8T Neo FIS2R AMIBOOT.ROM not working

Hi
Had a game crash on my system, and froze everything, so had to restart manualy - now I get the error BIOS is not installed..
I have downloaded a copy of the bios (not latest) and changed the relevant ROM file to AMIBOOT.ROM and copied to a freshly formated floppy.
I inserted the disk, held down CTRL and HOME and started the computer...
After a while of running through the messages of BIOS not installed and no SATA installed (which is correct), the floppy drive light comes on, and then after a while (afet I have released the CTRL and HOME keys) I get a message saying "Remove disks or other media, Press any key to restart" then nothing, if I press any key - it says the same thing untill I remove the floppy... and then it restarts again.
I have tried to restart using the floppy and the CTRL and HOME keys about 20 times so far - always the same result - I have even tried diferent versions of the BIOS.
Any ideas?
I only have one stick of RAM (256Kb - 333) and two IDE HD's
Many thanks in advance
GreenBoy

Hans
My Set up is as follows (from the top of my head as I am doing this form work)
K8T Neo FIS2R.
AMD 3300 745pin chip set.
1 stick of 512Mb ram (non branded - baught from Watford Electronics)
2 x 200Gb Maxtor HD's
1 40GB Seagate HD
1 DVD RW
Power 500W
Dont know what else you need...
Anyway - last night I reset the CMOS in the way you described.
Still cant find the VIA settings in the Advanced Chipset or elsewhare - but I will. urned of SATA in Intergrated Peripherals...
Anyway - what then happens, is it says it cannot boot.
I tried using a Win98 SE boot disk - and all the drivers were listed as not possible to load or something...
Any way - deciding I did not have anotehr boot disk to hand - tried Symantec Ghost - still same result.
Finaly I tried WinXP Pro, and found that this installed all the bootup files no problem at all - what was then found was that my C: partition was missing - yup boot sector had completely disapeared.
Anyway knowing that I have recent full backups og my primary drives using Ghost, I took the plunge, created a partition in the unalocated space, reformated the drive, and reinstalled WinXP... all seems ok for now... except the message regarding no BIOS - but from what you say as soon as I fing the switch I will loose that again.
The strange thing is I never used to get this message before, and do not remember setting anything up for SATA - couldnt afford the disks at the time....
Thanks for the help Hans, you have been more than gwenerouse with your time , but can you please give me some more information? (Im a bit of a Nooby at playing with BIOS etc as they scare the crap out of me! )
1) Why is the detail of my system so important? I have made no Hardware changes for approx 6 months and everything was fine untill the game crashed, so therefore, dont see why this should affect things.
2) Why did the flashing of the BIOS not work? I was following the instructions carefully - but nothing.. therefore in my Nooby mind this means there is something else wrong, stopping the flashing from working.
Again - many thanks
GreenBoy

Problems with OC in MSI K8T Neo FIS2R!!!

Hi!
I have faced problems when making OC in my Athlon 64 3400+. I do not obtain to increase the FSB for 213Mhz more than without that they occur stopped or reset. I am using 1Gb (2x512) of Ram (Corsair CMX 3200LL PRO).
In the internet many stories exist that chip VIA K8T800 is not good for OC, because the AGP/PCI cannot be stopped with fixed values.
Exists some form to obtain with stability in this Mobo one overclock descent, with FSB of at least 220Mhz? The lack of stability in overclock limits the processor very, what it finishes in forcing to who knows to abandon the K8T Neo, passing to a Mobo that uses Nforce3 250, for example.
If somebody will be able to help with tips to try one overclock for FSB in 220mhz with stability would be very grateful, friends!
my system
Athlon 64 3400+ (cooler venus 12)
MSI K8T Neo FIS2R
1Gb Ram (512x2) Corsair CMX 3200LL PRO
ATI Radeon 9800XT 256Mb
120Gb SATA Maxtor 8mb buffer
Audigy 2
420W Thermaltalke
Case Lanfire Thermaltalke
Monitor LG Flatron 17 700P
CD/RW+DVD
LAN (adsl 400k) + Fax Moden (56k)

Take your sata drive off and you can overclock higher. There is no PCI/AGP lock so the speeds are affecting your sata drive. 210 mhz. system clock is about the limit before the sata drives start to act up.
The problem is with that particular VIA chipset. No way around it has been found to work in a practical manner.

MY K8T Neo-FIS2R with AMD 64 3000+ auto shuts down

I have run this system for several months with core centre all
arms going off when playing graphic intensive games (Call of duty, Counter strike etc).
I have added system fans to cool the machine sown, and this seemed to work ok until three days ago when the alarm was followed by a system shut down!
I can see no obvious problem displayed in core centre, but suspect that the alarm is CPU fan speed related - I am running the AMD supplied Heat sink& Fan assembly.
Anyone have any ideas why this problem has suddenly got worse?
CPU Type AMD Athlon 64, 2033 MHz (10 x 203) 3000+
Motherboard MSI K8T Neo-FIS2R (MS-6702)
Motherboard Chipset VIA VT8383 Apollo K8T800, AMD Hammer
System Memory 1024 MB (DDR SDRAM)
BIOS V.1.8
Video Adapter VIDIA GeForce FX 5600 (256 MB)
Temperatures: (minimal load)
Motherboard 40 °C (104 °F)
CPU 44 °C (111 °F)
Seagate ST3120022A 33 °C (91 °F)
Seagate ST380011A 34 °C (93 °F)
Cooling Fans:
CPU 2860 RPM
Chassis 3013 RPM
Voltage Values:
CPU Core 1.47 V
+3.3 V 3.10 V
+5 V 4.97 V
+12 V 11.92 V
-12 V -12.20 V
-5 V -5.30 V
+5 V Standby 4.90 V
Is this a BIOS/Core Centre issue or CPU fan or maybe a PSu shortfall since the problem only manifests itself when CPU is under high loads?

Hi mcihael ,
Thanks for the tip about Fanspeed. I have seen it around but never thought i had a need of until now.
I must admit that having all of these extra applications supplied with the motherboard can get a bit confusing - the only real use that Core Center has been to me was the alarm going off letting me know that something serious was wrong!
What's your opinion on case fans? Should they be EXTRACT, INTAKE or a mixture? Most people i read about say exhaust fans are best to take away the hot air, while others claim intake fans help keep a flow of air around the CPU cooler.
Spooks

K8t neo fis2r system help

Similar Messages

Maybe you are looking for