K8T Neo FIS2R Won't Recognize HDDs

Here’s my situation. I am not new to building computers, but new to the AMD Athlon64, MSI boards, and SATA drives.
I purchased the K8T Neo-FIS2R (601-6702-010) main board. A single 512 MB DDR memory stick is installed. The only card installed is the ATI Radeon 7500 ALL-in-Wonder video card. I cannot get the system to recognize hard drives. I have made many changes in BIOS, but have been unsuccessful.
At first, my intention was simply to take my almost new Maxtor Diamond Max Plus 9 120 GB ATA HDD and install it with the K8T Neo motherboard. The disk has been previously formatted with Windows XP Home, and has various other programs installed. It was working fine in my older system. I put this drive (properly connected to the IDE1 on mainboard), and the K8T Neo would not recognize the drive at all. In fact, all I received were messages that SATA Raid devices were missing (apparently the Promise controller complaining). Trying to deactivate the SATA controller via bios did nothing.
Next, I decided to purchase a Seagate 160 GB Barracuda SATA HDD (ST3160023AS-RK), thinking maybe then the system would at least recognize an SATA HDD. (of course a lot of this shows my naivete’ with newer SATA standards/componets/MBoards) Initially it was recognized, and I was able to use Seagate’s software to partition the drive and format it. However, after rebooting and attempting to install Windows XP, the drive was no longer recognized by the system. On the POST screen, the VIA controller does list it as master device 1 in the SATA.
Okay, here’s what I want: I want to install the Barracuda 160 GB HDD SATA as my boot drive, and take my slightly older Maxtor HDD and make it a secondary (or slave) drive. This means a mix of SATA and ATA drives. Since MSI’s documentation both in manual and the website provides no help (that I can find) on this issue, I need suggestions on what to do. The only explanation in K8T Neo manual is to create an SATA Raid array. I do not want to do this. I simply want the SATA as boot drive, the ATA as secondary (or slave) drive, and for both of them to peacefully coexist! How do I make the mainboard recognize this?

Quote
Originally posted by saat0014
Are you getting the error when you insert the disk and it looks for the drivers on the disk? Or are you getting it at the Windows installation screen. Maybe you should try using the promise drivers and hook up your drives to the promise controller. Here's how to get the Seagate drives to work on the promise controller. Promise Scroll down to where I posted and you'll find hopefully all you need. If you need help, just ask
The error is coming at the Windows installation screen. The drivers already (seemingly) load.
I have tried installing the Promise drivers, although not as you posted in the linked thread. I only have the one SATA drive... do I still need to configure it as RAID?
I'll try this today. In all my years of building computers, I've never had as many problems as I have with this system. This is so frustrating.

Similar Messages

MSI K8T Neo-FIS2R won't power-up

My MSI K8T Neo-FIS2R won't power up when I switch it on. All that happens is the fans "jolt" a few millimeters and that's it
Using an X-Pro 460w which does work as I have tested it on this PC
Any help would be greatly appreciated

I think I have found out the problem
Using my old Enermax (350) I was able to boot up the AMD 64 2800 every time but the PSU made this weird electrical sound - I think because it was being overloaded (I think as it doesn't make this sound when used with my XP 1800). I then reverted back to my new X-Pro (460w) and after a few attempts I managed to get the ram module and CPU powered... slowly adding more fans it became harder to boot and eventually the GPU fan wouldn't run once I plugged another fan in... I'm guessing this is because my PSU is too weak to power the juice guzzling AMD
I'll need to break the bank once again I suppose

K8T Neo-FIS2R - won't post.

Hello friends,
specs:
K8T Neo-FIS2R
Athlon64 3200 (retail with fan)
two 512mb stick Corsair
1 36 gig SATA Raptor WD hdd
1 80 gig SATA WD hdd
Antec 430 w "TruePower" PSU
ATI 9600 pro
Sony optical drives.
Mitsumi 3.5"
buncha Antec fans.
So I got my new baby all put together and took a deep breath and started it up.
All the fans came on, hdds making hdd type noises, CPU fan a-spinning.
Nothing happens. Doesn't post. No video at all. The MSI usb/diagnostics dongle has all 4 LEDs shining, and supposedly that means the CPU is damged or not seated right.
Poop.
So I take it down, pull of the heatsink and look at the CPU. Looks good. Just to be sure I take it out, look for dust or damage or any abnormalities. Nothing. No physical defects on the CPU pins or the socket. Alright. I carefully put the CPU back, put the heatsink back on (Am I the only one who loves how the heatsink attaches? Bravo AMD!) and.....the same thing happens. I sigh loudly and commence with the near hysterical swearing. Girlfriend announces she HATES it when I build a new PC.
Tried all sorts of other premutations, one stick of ram, unplugging all periphs in different combos, pressing the power button while petting a monkey and eating fire. You name it, I've done it. Does anyone else abuse couch pillows?
You gotta let it out man.
I've probably inserted a few hundred CPUs into ZIF sockets over the years, so I'm 100% certain I didn't muss it up.
So before I RMA these little sweethearts (both the mb and cpu, because how can one tell if it's the socket or cpu?) has anyone else been down this road and want to give me the magic cure? Or maybe just a hug?
Much Thanks to you. Have a good weekend.

Hello Friends,
The Hynix dimms in several arrangements, no go.
I also, uh, borrowed some infineon from work. Tried in several configs, no go.
Samsung no go.
Enter: Despair.
As I sat and stared at the machine in sort of a "I just spent a lot of money and what do I have?" sort of way, mine eyes did fall upon the gleaming brand new Antec "TruePower" psu.
Mind you, I had a perfectly acceptable 450 watt. No problems at all with it. It was generic and cost 30 dollars. But in the quest for stability, nay, in the quest for the very computer bliss we all aspire to, I laid out my coinage for the Antec fancy schmancy model. I thought, "Time to go with a real name, a real psu." .
And here's where the story ends. I swapped out the psu, thinking at this point I was sort grasping at straws, and wham bam thank you ma'am, here I am sitting by my gleaming tiny god, my humming MSI K8T, all is forgiven.
Thanks for the help all. The corsairs all seem to to do their job. Antec apparently does not test their rather expensive "TruePower" psu.
Ironically, the brand of the no namish psu appears to be "Works", emblazoned proudly on it's side.
So if you think ram is ruining your life, stick a piece of crap psu in that rig and see.
There's only one thing left to say.
w00t!

New K8T Neo FIS2R won't post

I have looked at all the other threads in this forum, but can't find the solution.
Specs:
New K8T Neo FIS2R
New A64 3000+
New Mushkin 3500 Level One (Cas 2) 2x512MB
New Antec 550 (24A on the 12V)
ATI Radeon 9800 Pro
When I give it power, all the fans come on, the 4 LEDs on the bracket stay lit up, and then don't change, but I get no video or any other indications (such as beeps). The 4-Pin power connector, is securely connected in the proper location. The standard ATX connector is also secure. I'd link to a picture to prove it, but my camera is charging right now.
Currently I have only power wires, power switch, system speaker, video card, and 1 stick of RAM in the first slot. I have tried it without the video card, without RAM, with RAM in different slots, just about any combination I can think of. I have even cleared the CMOS a few times. Nothing changes, I always get stuck with the 4 LEDs. I don't have anything connected to the USB headers either (that was mentioned in another post).
I know some people have mentioned that the Antec 550's 24A on the 12V isn't great, but it should be more than enough amps, the way my system is setup right now.

Hi
It does not sound like a major prob, it sounds like a PSU or memory problem, anyway of checking MOBO with another PSU with at least 20A on the 12v. Also check the memory sticky at top of the posts and see if your OK memory wise, another possibility is that one of the mounting screws is tracking from the board - try removing screws and see if it boots, also check none of the cables are touching the case or MOBO.
MOBO and CPU seem fairly resilent, so faulty parts are not to likely, although one never knows. Another thought the Jbat1 Cmos jumper is on pins 1 & 2, 1 is marked on board, and you could try clearing CMOS. a corrupted bios could also cause this.
Best of luck, lets know how you go
Jocko
PS. looking at the stickys at top, Bas has put one there about a compitition by MSI, one of the questions is about Radeons needing extra power( has an April 1st entry date!!), it is worth checking, does your Radeon have its own supply, you could always remove it and see if it boots.
Cheers

6600GT not working with K8T neo-FIS2R

I recently returned a K8T NEO-FIS2R MB for repair. The problem was that the PS/2 and USB ports were broken. However the MB has been returned and the PS/2 and USB ports work fine. I posted about this several months ago.
Now the AGP port seems to be broken (not the actual slot). I have tried a 6800 Ultra and a 6600 GT (AGP version) GFX card in this slot. Both cards fail at the driver installation point. I have tried driver versions 66.93, 67.02 and 67.03. I also tried 3 versions of the via drivers 451, 453 and 455. Even tried XP with SP1 and SP2. The PC will sometimes BSOD, reset, won't boot into windows. The drivers sometimes install then other times they won't, etc. The problems only seem to be with the drivers for the GFX cards.
The 6600 GT works as I have tried it in another MB without any problems.
I know the memory works fine as I used memtest86+ for a couple of hours on the default settings without any errors and it works in another PC.
The spec of the PC is:
XP pro
K8T NEO-FIS2R MB
512MB corsair XMS at 2.5-3-7-3
XFX 6600GT
40gig HDD
FDD
Plextor CD writer
DVD Rom
PSU is a Q-tec 550W
I know Q-tec PSUs are not up to much from what I have read elsewhere in this forum, but I have had it running in a similar system with the 6800 Ultra installed without any trouble (even with the above MB before it went faulty). I have also tried a 400W PSU, that came with the case. The Voltages on the 12V line are between 12.00 and 12.03 when using the Q-tec PSU.
Has any body else had these problems with the 6600GT in the mentioned MB.
Also, how can I check the serial number on the MB with the label on the box, as this MB that was returned to me looks to “clean” to be the one I sent away for repair.
Thanks for any help

Hey, I'm glad to see a post on the new Gforce 6600GT AGP card. I just recently put together a brand new system (see my sig for specs). System runs great. The only thing I wanted to do was replace the video card, and after a great deal of anxiety I decided the Geforce 6600GT AGP was the best bang for the buck.
Well I got home, installed the card and never get passed the bios screen. (shows your processor, memory, memory siz), the screen u hit DEL to go into the bios.
The system doens't lock up, NUM LOCK can still be turned on and off, and CAPS can be turned of and on... but thats it. Just sits on that screen. I can't go into the bios either.
what settings do I need to do prior to isntalling this card to get it to work.
Let me know if you all need anymore details to help me out.
oh, I did reset my frequency to 10x200 (which is what I think the 3000+ is supposed to be at).

[Athlon64] MSI K8T Neo FIS2R BIOS Update when? CnQ no workie!

The MSI K8T Neo FIS2R (MS-6702) hasn't had a BIOS update since 3-4-2005!
I put a Sempron 64 3000+ in my motherboard, and was very disappointed that it is recognized as an "AMD Unknown Processor". Sure, it works, but one of the reasons I bought it is in the hopes of getting AMD Cool n Quiet to work. However, apparently the AMD driver can't recognize the CPU due to the old BIOS on the motherboard.
Every other MSI skt 754 board supports Sempron E6 revision already. Why not the K8T Neo FIS2R? Where have all the MSI BIOS programmers gone? I have been waiting 2-months for a BIOS update to support the E6 Semprons. I have asked and begged MSI Tech Support. I am tempted to switch to ASUS or some other company that is actually timely with BIOS updates. Only reason I haven't yet, is this board is everything I want EXCEPT for Cool n Quiet not working. It's starting to look like there is no BIOS update in sight, so I am very disappointed.
Anyone here work for MSI can confirm there are no plans for a BIOS update? Because I don't want to wait around for something that's not going to happen.

Sorry, I didn't mean to imply I thought the mods here are MSI staff... I was just kind of hoping there's MSI staff lurking here, seeing what people think of their products or seeing what people complain about.
No, pretty much C 'n Q is the only reason I'm disappointed, but it was something I was really set on getting to work since this is a server that's up 24/7, but isn't utilized but maybe 4hrs out of a given day. I could reduce frequency and voltage, but unlike C 'n Q, it won't automatically increase speed and voltage based on demand - which is something I want since although it's a server, I also use it as a regular PC as well.
I've even tried the 2.33 beta BIOS with no change, and even found a 5.52 BIOS in their BIOS testing directory. I guess that BIOS was for a different kind of 6702, although I had pulled out the peripheral modules with AMI's MMTOOL and they looked the same as the existing BIOS, but that BIOS killed my motherboard so it couldn't have been for a regular 6702. I had to desolder the BIOS chip with a heat gun, reprogram the old BIOS back on it with an EPROM programmer, and solder in a socket. I guess that shows my dedication to get C 'n Q working!

K8T Neo-FIS2R/FSR no POST

I have a K8T Neo-FIS2R/FSR (MS-6702) which is, along with all my other components (I'll list them later), over a year old. It has been running just fine until the other day. I have not modified any hardware or BIOS-settings recently.
The day before yesterday my speakers put out a high-pitched shriek and the screen turned black. I then turned off the computer (it seemed to still be running, fans spinning). As I switched it on it let forth 8 beeps followed by a paus, and then 8 beeps again, over and over. I switched the graphics card for another one, no difference.
I then left it turned off for a few minutes. Then I booted it up again, and voila, it worked fine. Then after a few minutes it died the same way, and when I rebooted it it started beeping again.
Switching graphics card doesn't help. I powered it on without a graphics card plugged in. Then it made 8 beeps, and then silence. The cycle was not repeated, as it was when the card was in.
I then used another motherboard, another CPU and other RAM, same graphicscard and harddrive, and it boots into Windows just fine and seems to be quite stable for the day I've tried it.
I then switch back to the K8T-motherboard with it's CPU and RAM (still same graphicscard and harddrive as the other one), and it boots fine. After almost an hour it dies again. On boot, beeps. Wait a few minutes, boots again, then dies. Beeps next time. Etc.
The 8 beeps apparently mean there is a problem with the video card. I have tested two video cards that both work fine on another motherboard, no difference.
Because it dies after a while when it has rested, I suspect some sort of overheating issue. I put a bigass fan blowing at the motherboard and video card but that didn't seem to do anything. The fan on the video card is clean.
I have hooked up the D-Bracket 2 that accompanied the motherboard. It has some lights flashing depending on what is going on, and it halts on "Early Chipset Initialization", which is phase 2 of 16 (1st being "System Power ON"). When I press the power button, the LEDs on my memory sticks flash for a few seconds (showing activity), and the D-Bracket lights up. Then the memory-LEDs go to rest (inactivity), and the D-Bracket halts. Fans keep spinning but there is no life. No beeps.
After leaving the computer off for the night, I cleared the CMOS. The computer booted and ran fine for a couple of hours, then it suddenly made a noise in the speakers, and the monitor went black. Fans still spinning. The little light at the monitor indicating that it is turned on was flashing, as it does when the computer is off and the monitor is on.
This is the hardware in my system at the moment. I have removed plenty of stuff to rule out other components but even with just this it won't work. No mouse, keyboard or other drives attached, just this.
CPU: Athlon64 3200+
Memory: Corsair TWINX1024-3200XLPRO DDR
Power: Thermaltake Purepower Butterfly 480W W0020
Output: +5V (35A), +3.3V (28A), +12V (17A), -5V (0.3A), -12V (0.8A)
Graphics: Gainward GeForce 6800Ultra 256MB GDDR3 AGP8X, "Ultra/2600 Golden S",
Motherboard: K8T Neo-FIS2R/FSR (MS-6702)
Harddrive: Seagate Barracuda IV ATA 7200 RPM
Monitor: Samsung SyncMaster 957p
Any ideas, suggestions or questions? I am stumped.

Quote
I have removed plenty of stuff to rule out other components but even with just this it won't work.
Quote
Graphics: Gainward GeForce 6800Ultra 256MB GDDR3 AGP8X, "Ultra/2600 Golden S",
Quote
+12V (17A),
If your graphics card is like mine (see sig) with two power connections at the back you may have stressed the PSU over the last year to it's final end. Borrow or buy another PSU with at least 24 amp on the 12v supply. Your current PSU with only 17 12v amps was bound to fail. Especially since you state you had other hardware at one time. CPU Graphics card, case fanes and drives are all calling on the 12v rail to power them and your PSU just might not have it any more to do the job and the highest draw is at startup.
Try another PSU.

K8t neo fis2r- CMOS settings are wrong!

First I would like to thank all of you for taking the time to help me resolve my problem. My current system specs are as follows:
MSI k8t neo fis2r mobo
AMD athlon 64 3200+ (clawhammer I believe)
2x 512 MB Corsair Xtreme XMS Memory
Radeon 9800 Pro 256mb
80gb Samsung HDD
600W Xconnect PSU
After having problems with my computer not loading windows I downgraded my bios from v 2.2 to 1.9 because I heard that versions higher than 1.9 may have problems with my older clawhammer cpu core. The bios flash worked in that I can now start up my computer if I reset CMOS and load default settings. However when I load my computer this way my Core Center is displaying my Vcore at around 1.1v. 3.3v is at around 3.41, 5v is at around 5.1, 12v is at around 12.1v. In the past I needed to manually set my Vcore under bios at 1.4v or 1.5v to get it to start, and when I started it that way Core Center correctly displayed the 1.4 or 1.5vcore and stated that my computer was running at 2000Mhz. Now my computer is running at 1.1vcore and 800 MHz. If I clear cmos and enter setup to try to change my vcore to 1.4 my computer will hang after the save and exit just as if I had restart my computer without clearing the CMOS. I have tried changing the mobo battery, which did not do anything. Its odd, if I choose to load default settings and continue, my computer will start up and is entirely stable. If I choose to enter setup however and choose to load default settings and then save and exit, my computer will hang just as if I did not reset CMOS to begin with.
I really do not know what to do here. I was thinking about trying something like this http://crystalmark.info/software/CrystalCPUID/index-e.html to up my vcore after I get my computer started so that I can play my games without the low fps I am currently getting. I know this fix would not get my computer to start up without resetting CMOS, but would it work as a temporary solution?
Does anyone have any ideas for what is wrong? Thanks again in advance.

Thats bad news for me!
Anyway, I found a program called RightMark CPU clock Utility that has enabled me to get my 2000 MHz out of my cpu by setting FID to 10.0x and VID to 1.550v
With these settings Rightmark is reporting an idle cpu temp of around 31 C, but when I get in a game like world of warcraft the temp will go all the way up to around 90 C, which I feel is incorrect. Ive had my computer become very unstable in the past when the temp got near 65-70C. It seems to be perfectly stable at the moment, even under the high loads of world of warcraft. Do you have any thoughts on this?

Msi k8t neo fis2r help

hello. in need of a little hand here.
board won't post.
i've just thrown together my new system with monitor and power cable plugged in:
64 3200+
k8t neo fis2r
crosair ev ddr400
his radeon 9800 pro ice-q
tagen 480w psu
when turned on the fans all start and the power led flashes on and off slowly. screen never displays.
mobo never came with d-bracket so i can't diag the problem myself, scared it's a cpu prob.
cheers
NIB

so far all i've only wanged in the items listed (512 of the ram) and i have connected the additional 4-pin, although thanks for the mention - it's always the stupid that i end up overlooking. I've noticed that when the psu is plugged into some older p3 & p4 systems their bios' don't post. think there's a problem with the psu, although it claims to be 24a at 12v.
Cheers
NIB

MSI K8T NEO-FIS2R: RAM problems

I have the motherboard K8T NEO-FIS2R with AMIBIOS 2VMS V2.0 010505.
I tried these DDR-RAM:
DDR-RAM 512MB PC400 CL3 Kingston KVR400X64C3A/512
DDR-RAM 512MB PC400 CL3 Samsung
but the motherboard recognizes only 256 MB for both. The RAM are good: I tried them in an other pc!
Now I have installed an A-DATA ram 256 MB and the motherboard recognizes 256 MB!
Do you think that my motherboard is defective?
Thank you in advance.
P.S. I'm sorry for my bad english.

No the memory controller is onboard the CPU so in any case the MB is not defective. However the CPU revision may hold you back on some RAM especially if you mix make and model RAM on the same channel. A socket 754 CPU only has one channel so all RAM must be matched to work properly.
If those Sticks can only be seen as a wrong value when used by themselves it is likely that either they have errors or the timings in Bios are improperly set to azllow them to work. In this case you can normally find out what is going on by running memtest86. If you get errors on test 5 or 7 then you have timgs timed improperly and any other errors would show bad RAM.
Another case is not having enough power for everything to work properly together. Usually this happens when you don't have enough 12v amps for these newer rigs.
Post complete specs and test results and maybe we can help you further.

MSI K8T Neo-FIS2R SATA CD/DVD Support

Does anyone know if the K8T Neo-FIS2R mobo will or can be made to support a SATA CD/DVD drive. I am having no luck so far either getting it to recognize the drive or finding any info as to such.
Any help will be greatly appreciated.
Cheers

I was able to answer my own question. I was doing a bit of searching around on the MSI website and happened across a newer bios that doesn't come up in a regular search. The regular search turns up this page http://www.msicomputer.com/support/bios_result.asp (obviously inputing the correct platform and model) showing BIOS v2.2 as the most current. But by poking around on the site a bit, I came across another BIOS page for the same mobo, http://global.msi.com.tw/index.php?func=downloaddetail&type=bios&maincat_no=1&prod_no=565 showing BIOS v7.1. I figured I'd give it a try and low and behold the bios is recognizing my SATA DVD Burner.
The hd array has to be connected to the Promise controller as it will not see the optical drive even if it is set to SATA mode. I hooked the SATA DVD burner to the VIA controller and changed the setting in the bios for this controller to SATA mode as opposed to RAID mode (this was not an option on this controller in the BIOS before the flash to v7.1). I also had to have the PATA controller set to enabled or it would not recognize the drive. It is now a recognized device and shows up as an option in the boot menu. I added an additional SATA DVD drive to the other VIA SATA connector and it recognized it right away and made it available as a boot device. I tested with Knoppix and it booted fine.
Hopefully when I try to load XP this evening, I will have a winner.
Thanks again for your replies!!!

Problem with MSI K8T NEO-FIS2R

When I boot my computer I get a message invalid boot.ini then it says c:\windows and windows starts normaly. What I don't understand is why do I get invalid boot.ini Anyone knos how to fix this?

I'm sorry for no specs. Here you go
MSI K8T NEO-FIS2R
AMD 64 3000+
2X 512MB 400MHz Ceon CL=2,5
HDD 120GB WD
HDD 4GB SEAGATE
CDR DVD-RW NEC ND3520
CDR SONY
400W POWER SUPLY
primary master CDR DVD-RW
primary slave NONE
secondary master CDR SONY
secondary slave HDD 4GB
and last HDD 120GB on primary raid
NONE on secondary
I have ORIGINAL windows xp with sp2 on 120GB HDD. I bought this computer and they put windows xp on my system.

K8T Neo-FIS2R with Athlon 64 4000+ mobile CPU

Doing some research on the net, I found out recently that the older mobile CPUs differ from desktop ones just by the lack of a heat spreader on top of the core. And I read up about many successful updates from ppl using the mobile CPU on the desktop socket 754 boards. This is for my 2nd system listed in my sig below - the K8T Neo-FIS2R. I found a pretty good deal on the Newark CPU AMN4000BKX5BU recently (4000+). I took my existing 3000+ CPU out and I separated the heat-spreader from it. Underneath it's almost identical, except the core is a few mm larger than the mobile CPU. I mounted the heat spreader on the 4000+ CPU and made sure the core has good contact with the heat-spreader (checked the thermal paste imprint). Mounted the CPU in and the board powers on but doesn't POST. I then put my 3000+ in and works just fine. I repeated this 3 times, and just couldn't get the 4000+ to be recognized by the mobo. I thought the CPU may be bad, but it comes from a good source, so even though it's still a possibility, I started doing more research. And then I realized that I forgot to change the core voltage in BIOS from 1.5 to AUTO. The mobile CPU is rated for 1.35v. Do you think this is what affected it? Or is it because I'm on BIOS v.1.9 ? Latest BIOS is 7.1, but all versions passed 1.9 only introduced compatibility with Sempron CPUs (which I'm not using) and it limited DDR recognition to 333 only. I'm using DDR400 which is running well at 200MHz. All higher BIOS levels don't allow to run it in stock speed at higher than 166MHz. So that's why I wanted to keep the v.1.9.
Any ideas why the 4000+ CPU wouldn't be recognized by this board?
Thanks in advance!

I'm making some headway, but in effect, I temporarily hindered this system more than it was I got the CPU to finally work, but it only recognizes 1/4 of the memory I used to have... here are the details:
I upgraded BIOS to the latest 7.1 and the installed 4000+ CPU didn't allow the system to POST neither. I then cleared the CMOS and just for good measure removed 1 of my memory sticks (I had 2x1GB, as listed in my sig for the lower system). Then the old faithful came to life again After making more test I noticed that no matter what I do, whether I use DDR400 or DDR333 sticks (I also have those in 2x1GB), the only way it works is with a single stick in DIMM1. In manual, the configurations show that that memory can be inserted in different DIMM sockets, not necessarily the 1st one, but in my case, no other setup works than a single stick in DIMM1. As I mentioned earlier, BIOS versions above 1.9 (I checked them all in the past) don't allow DDR400 to run at 200MHz, but only at 166. Also, ver.7.1 reports CPU temperature incorrectly, about 10 degrees Celcius lower than it actually is. I actually noticed that in the past with my other CPU, too. Since nothing else could be accomplished here, I decided to go back to BIOS v.1.9. But the situation relating to RAM didn't change. It still only functions fine with a single stick in DIMM1.
I also tried resetting CMOS several times at different occasions, and when reset in ver.7.1 it would POST with 2 sticks of RAM in, but after loading BIOS settings, it would work fine (only as far as POSTs, because I never booted to OS during these tests) and would restart fine as long as it wasn't completely shut down. Once it was shut down, it wouldn't POST again.
In ver.7.1, the CPU was recognized by BIOS correctly as 4000+, however back at ver.1.9 BIOS recognizes it as 4200+ (something that doesn't exist for socket 754, AFAIK). However, the DDR400 is again working at 200MHz and the CPU core temp is reported correctly.
In ver.1.9 the CPU voltage when set to AUTO would run at about 0.9v, which might've been causing no POSTs until CMOS was reset. I manually lowered it to the minimal setting possible of 1.4v. It is rated at 1.35v and now is reported to run at 1.38v and still much cooler than my older desktop CPU 3000+. From what I read, AMD was doing binning on the mobile athlons, so I'm sure all of them can work fine even at 1.5v or higher, if needed.
Anyway, I temporarily gave up and decided to wait for some golden thoughts from you guys (or MSI Support, whom I also contacted about this, but it'll be a miracle if they respond with some help). Then I booted up into Windows, and even though CPU-Z recognizes the single stick of 1GB RAM I left there, Windows only reports it as 512MB. Also, CPU-Z reports the CPU in one spot as 4000+ and then in another (a little below) as 4200+. I guess the multiplier of x13 causes the confusion? Could that also be the reason for not recognizing more memory? I also tried lowering the HT Link in BIOS to 200 and 600MHz and that didn't help as far as allowing to use the 2nd stick of RAM. Please check the below screenshots for more details.
Thanks

K8T Neo FIS2R "1394 Net Adapter" in XP's Device Manager

I can't get my firewire port to work or recognize devices attached to it!
I just built a system with the K8T Neo FIS2R and an Athlon 64 3400+ running at stock speeds. It also has GeiL Golden Dragon (matched pair) PC-3200 DDR which is running 1 trcd increment higher than rated to ensure stability. I have a lot of devices installed and have reinstalled windows fresh twice now with the same problem.
In device manager, the "VIA OHCI Compliant IEEE 1394 Host Controller" seems to be fine, but in the "Network adapters" category, I see my D-Link Wireless NIC (fine) and "1394 Net Adapter" with a big yellow exclamation mark next to it.
This computer is for a music studio and I absolutely have to use the firewire port because DigiDesign's Digi002 needs to be attached to the computer and communicating properly in order for ProTools 6.1 (our main studio software) to install and run.
I also have the BIOS set to enable the on-board sound, but I also have a pro-audio card installed (the M-audio Delta 1010) and the computer doesn't even see the on-board sound device whether enabled or disabled, when the M-audio card is installed (but this isn't my main concern, getting the firewire working is).

Quote
Originally posted by Jocko
version 1.3 should be soon. v1.3B2 the beta is available it may help
Where? Nobody seems to be able to provide a valid location to acquire this mysterious "1.3 beta BIOS". Someone mentioned it is on the german MSI website. If it is, it's hidden, because I scoured it and found nothing.

K8T Neo - FIS2R (model 6702) SATA and RAID Problems = Hair Loss

Hi All,
new to the forum, have searched but nothing like my problem exist.
I have a K8T Neo FIS2R M/B and trying to get a single SATA HDD working for my secondary drive. primary is a IDE which works well and I want to leave it.
I have plugged in the SATA HDD into the SER 1 port ( Promise 237 ?) anyhow the bois at startup or post recognises the drive, but then says soemthing like you have set up raid before F1 for setup F2 to continue to boot.
I have pressed both f1 and F2 at various time, but it appears that it want to turn the single drive into a RAID system, which is not possible with one drive !!....
Anyhow windows XP then boots up and loads a RAID driver and also the promise RAID drivers. the real problem is that XP sits and waits for the raid which never comes and during startup on XP. it is extremely slow.
Does anyone have any ideas. I am not that computer techy as you can see by the description, but it appears that I cannot get into the RAID bios to turn it off.. I have zapped the bios to try and reset it. basically i am loosing my hair ove this.
if anyone had some step by step instructions how to prevent raid from switching on at the bios and then in XP it would be greatly appreciated
Jeff

Hi All,
Sorry for the slow reply, retrieving the box from the bottom of the swimming pool !!!
I set it to SATA as you have indicated Hans, I did check that setting. Thankyou for checking.
Spray, I have tried the P20378 setting as well. You indicate that you need to press F6 when installing the OS. I have WinXP running already on an IDE master and am trying to set the SATA up as a secondary disk drive.
As I indicated above, the machine runs slowly to the point of it being a 486 when I use either promise or Via controllers.
I have since removed the drive and are now having problems with XP on boot up/startup. The thing seems to hang or go slowly when the horizontal bar runs across under the Windows XP logo. I have turned everything off in the bios both Promise and Via. I am at a loss as to why:
1 it runs slowly with the SATA drive in ( also does not show all the auto loading icons near the clock)
2. why it hangs when I remove it and turn both SATA controllers off in the bios.
I have a feeling that I may have corrupted part of the registry playing around. Any thoughts... going bald :-)
I really appreciate the feedback so far

K8T Neo FIS2R Won't Recognize HDDs

Similar Messages

Maybe you are looking for