K8T Neo FSR with Audigy 1 Problem

I just received a major upgrade, for me anyway, last night. ALL I was getting on boot was 4-RED LED lights on the D-Bracket2 connector. I was ready to RMA the WHOLE thing to Tiger Direct, when I decided in one last ditch effort to try again.....I pulled my Audigy, and wham, it booted normally. Now let me describe.
1. I KNOW it's not a power issue, as I had EVERYTHING but Sound and Video removed, and unplugged, including hard drives. The D-Bracket2 LED's were still all-red on boot.....system would not POST.
2. Pulled ALL hrdware from system, except Video and Audigy, same results.
3. Last try, pulled EVERYTHING, including Audigy, and it booted normally.
4. Re-connected everything, except Audigy, re-installed Windows XP SP2, no problems, system runs.
I tried EVERY PCI slot with the Audigy, ALL with the same results; system would not run with it in there. The card was good 15 minutes prior on the OLD Abit Board. (meaning it works.)
ANy ideas???
System Specs:
K8T Neo FSR MB
Athlon64 2800+ CPU
GeForce Ti 4200 128MB Video
512MB Mushkin Green Memory (1 DIMM)
Maxtor 160GB HD
WD 20GB HD
45X CD-ROM
24X CD/RW (Sony)
onboard NIC, Sound (Audigy problem made me resort to the onboard sound)

Suggestions:
http://www.tigerdirect.com/applications/SearchTools/item-details.asp?EdpNo=1104458&CatId=1078
The above might be only 420W but it has 18 amps under 12+, which is fine for your setup.
http://www.newegg.com/app/ViewProductDesc.asp?description=17-148-002&depa=1
http://www.tigerdirect.com/applications/SearchTools/item-details.asp?EdpNo=719596&CatId=1079
http://www.tigerdirect.com/applications/SearchTools/item-details.asp?EdpNo=719582&CatId=1078
http://www.tigerdirect.com/applications/SearchTools/item-details.asp?EdpNo=1120272&CatId=1078

Similar Messages

  • MSI K8T NEO FSR with AMD 64 3200 - Can´t install WIN XP

    Hi.
    I´m writing you because i have a problem with an MSI K8t-Neo FSR.
    The description of my PC:
    MSI K8t-Neo FSR
    AMD 64bits 3200 (640 cache)
    HD 160 SATA Seagate Barracuda
    1gb DDR 400mhz
    Floppy 3 1/2
    CDRW 52x32x52 LG
    Video ATI RADEON 9600 XT
    The problem is the following:
    When I try to install Windows XP, when I press F8 to accept the Terms, it shows me an error message (IO 104 i think) and it hangs up or reboot.
    I tried with another two Proccessors and motherboards (same model obviously) but it didn´t work.
    Could it be a defectuous production serie of that model????
    Or what do you think the problem is????
    Thank you very much for your help.
    I´ll be waiting for your answer!
    Lucas Revale
    PF: I´ve already tried updating the BIOS.

    Thank you all for trying to help me!!!
    I've already tried using only te necesary drivers.
    I´ve also tried another VGA, another HD, another CDRW, another power supply, and an AMD 64 2800+.
    It seems to be that the three motherboards i tried were defectous.
    Does anyone has any other idea?!?!?
    I´d really aprecciate your help!

  • K8T NEO FSR bad bios or bad CPU?

    Hi - I just got a K8T NEO-FSR with an Athlon 64 3000 (newcastle) and 512 Meg of Corsair value select memory.  I installed everything fine and tried to install a fresh copy of windows xp home but I kept getting a blue screen of death and a registry error (from the CD!!).
    I then reformatted my drive and put a copy of windows 2000 pro on it.  After updating the drivers, everything seemed to be OK.  But - I was getting a few random problems (CD stopped working, freeze, etc).  I was going to try to install XP but I thought I should probably upgrade the BIOS first just to make sure that wasn't the problem.
    Well - I followed the instructions for updating the BIOS (I've done it before for other systems) and everything seemed to go smoothly until I tried to reboot.  Nothing - it powers up but doesn't do anything.  I assumed that something must be wrong with the BIOS.  I double checked which file I was using A6702VMS.180.
    I then tried a BIOS recovery.  I reformatted a floppy on a windows XP machine and put a copy of the BIOS that I had backed up before the flash onto the disk named AMIBIOS.ROM.  Then I unplugged the power supply and every piece of hardware except the CPU, reset the CMOS, and let it sit for 15 minutes.  Then I reconnected the floppy and plugged in a PS2 keyboard into the back.  Pushed down CTRL and HOME and turned the power on.  Nothing.  Tried it again with each CTRL key and with the regular HOME key and the keypad.  Nothing.
    The LED's on the back panel show all 4 red which the manual says is a bad CPU.  Could my CPU have died somehow?  Did I miss something obvious?
    My power supply is an Enermax 350W with 32A on 3.3V, 32A on 5V, and 17A on 12V.
    Any thoughts?  I'm a little annoyed that I can't find a definitive source for how many amps on each of the rails the main board and CPU need.  I've found widely varying advice on all of the boards I've read.
    Thanks,
    Ted

    Quote
    1) The PSU that you have is quite weak on the +12v Rail & could be the cause of your problems, most people on here recommend 20a on the +12v Rail.
    I've seen people on various boards throw numbers anywhere from 15A to 30A for the 12V rail.  However, I haven't seen anyone quote any hard sources.  My back of the envelope computations:
    CPU: 89 W (max power from AMD's web site)
    MEM: uses 3.3V
    Floppy: uses 5V
    CD: 20W
    RAM: uses 3.3V
    HD: 15W
    Geforce2 GTS graphics card: 8W
    which gives me about 132W on the 12V rail at maximum power usage (which - since I haven't done anything I doubt I've hit).  This would be about 11 amps which is easily covered by my power supply.  And - the 89W number form AMD is for all the Athlon64 chips of which the 3000 is the very low end so it's probably less than that.
    Quote
    2) You may have faulty RAM & i would recommend running a memory testing program just to check that is ok.
    Could the RAM be faulty even though I had a windows 2000 setup running reasonably well?  The BIOS did do a memory check on each startup (I turned that on when I first installed the board).
    Quote
    As for the system not booting now, sounds like you have a bad BIOS flash & that you will need to get the BIOS reflashed or RMA your motherboard.
    I don't think this board supports reflashing - the chip is soldered onto the board.  Any idea why the rescue procedure isn't working?

  • K8T Neo-FSR SATA Limits?

    I have an old PC with an AMD Athlon 64 2800+ processor and a K8T Neo-FSR with a VIA® VT8237 chipset. This board has two 1.5 Gb/s SATA connections so I decided to put these to use by turning this old PC into a file server (NAS). I bought some refurbished 250 GB drives for a RAID 1 setup from Newegg and plugged them in and the firmware did not detect them. I upgraded the BIOS to the latest version (1.9) and it still didn't detect the drives. It's my guess that there's a limit on how much that chipset can support. Does anyone know what it is? I've tried searching extensively for it, but can't find any info on any limitations as far as SATA.
    For readers' simplicity, here's the URL for the info page: us.msi.com/product/mb/K8T_NeoFSR_FIS2R.html (copy and paste).
    Please note that I have no interest in purchasing a new system as a replacement. I know this board is a decade old and well beyond its EOL, but it works and it is paid for, so please don't go there. Thanks!

    Quote from: TV34 on 24-May-14, 00:01:27
    @ XFM
    from http://www.elektronik-kompendium.de/sites/com/1006201.htm
    Schnittstelle                                          Bandbreite     Reichweite   Geräteanzahl  Einführung
    Serial-ATA (SATA)                                150 MByte/s        1 m               4                     2003
    Serial-ATA-II (SATA 2 / SATA-300)        300 MByte/s        1 m             16                     2005
    Serial-ATA-III (SATA 6G / SATA-600)     600 MByte/s        1 m             16                     2007
    mfg Tino
     Got news for you, that's a typo there.  * Should read 3 G. You apparently still don't understand the proper terminology.
      Yes that's correct, SATA does not use jumpers for Master, Slave or Cable Select like PATA drives do.

  • K8T NEO FSR problems and questions.

    I read this in an article on http://www.hardware.no:
    "MSI is one of the companies that offer free upgrade to a new motherboard with better
    specifications, if you have bought 915P Neo2 Platinum, 915P Combo-FR or 915G Combo FR
    in the period of time between 21st and 27th june."
    Late in june, I bought myself  MSI K8T Neo-FSR motherboard, and an Athlon 64 3200+2.2GHz.
    When I run "Core Center", the program shows that my CPU idle temp is 60 Celsius and my
    sys temp is 36 degrees, which is COMPLETELY wrong?!?!.
    This is very weird, because I have a nice computer case with 5 fans that blow out all
    the warm air inside. When I play games, the CPU goes up to 65 degrees and my computer
    restarts. This is VERY annoying. How do you turn this off in BIOS settings?
    I'm quite frustrated with the thought that my CPU temp. shows 60-70 Celsius.
    I have read tons of other forums and I have found out that it's not only me that experience
    this problem. I seriously hope that you will fix this bug ASAP.
    Does this offer also apply to K8T NEO-FSR? Can I get a free upgrade?
    If I don't get my problems fixed, I will take further actions.
    My System specifications:
    MSI K8T NEO-FSR, Athlon 64 3200+2.2GHz, Asus Geforce 4 Ti 4400, TwinMOS 1024 DDR3200 RAM, Western digital 80+120+80 GB 7200 RPM, Chieftec BX Tower BX-03SL-SL-SL P4 / AMD, 2x papst 120mm fans, 2x 80mm papst fans, 1 fan in the door of the computer case.

    I never heard MSI was doing such an offer...
    Anyway, you need the latest BIOS, that solves the temps reading thing, this happens because AMD changed the CPU a bit.
    It's not getting that hot, it's just a reading failure.
    A BIOS flash should solve it.

  • K8T800 K8T NEO-FSR Memory Problems

    Just a warning before I start in, this is a pretty long post. I'm going to try to include all the information I can.
    Here's my system right now. It's running Windows XP Professional with all the latest updates.
    Processor: AMD Athlon 64 3000, 512KB L2 Cache 64-bit Processor. Not overclocked at all.
    Motherboard: MSI K8T800 K8T NEO-FSR, latest BIOS updates from MSI
    Video Card: ATI RADEON 9800PRO Video Card, 128MB DDR, latest Catalyst drivers from ATI installed. Not overclocked at all.
    Memory: Mushkin 184 Pin 2x512MB DDR400 PC-3200, running at DDR400 with Auto selected for all the memory timings in the BIOS. Memory placed in DIMM#1 and DIMM#2. Not overclocked at all.
    Hard Drive: Western Digital 80 Gig
    I started experiencing random reboots and critical errors in game applications on Sunday. The computer would randomly reboot at random intervals from Windows. In addition, while running games like Warcraft 3, Asheron's Call, or World of Warcraft I would receive frequent critical errors that certain sections of the memory could not either be read or written to.
    I figured that there was some kind of problem with the memory, so I downloaded Memtest86 and ran it. The first stick of RAM was in DIMM#1 and the second stick in DIMM#2. This was the memory configuration during all the random reboots and critical errors.
    Memtest86 came up with several failures during the 5th phase of the test. The same failures came up upon repeated testing in the same phase of the test. I decided to try to isolate the failure and see if one stick or the other was defective. I yanked out the second stick from DIMM#2 and left the first stick in DIMM#1. The first stick (which I'll refer to as the "good RAM stick") passed the memtest repeatedly. I then stuck the second RAM stick into DIMM#1 alone and the computer would not even POST.
    I then moved the second RAM stick (which I'll refer to as the "bad RAM stick") over to DIMM#2 alone and managed to get it to POST. The bad stick failed the memtest with the exact same errors during the same phase of testing as the combined sticks had failed during the initial test. For the sake of completeness, I moved the bad stick over to DIMM#1 alone and finally managed to get it to POST. However, the bad stick passed the memtest repeatedly. Puzzled, I moved the bad stick over to DIMM#3 alone and tested it there, which it also passed repeatedly. I moved it back into DIMM#2 alone and it failed the test repeatedly again and again.
    Intrigued, I then moved the good RAM stick into DIMM#2 alone, to try to see if perhaps there was some kind of motherboard error occurring. The good stick passed the memtest repeatedly in DIMM#2. I then moved the good stick into DIMM#3 alone and it passed the test repeatedly in that slot.
    After checking the motherboard manual to make sure I could do it, I put the bad stick in DIMM#1 and the good stick in DIMM#3 and ran the memtest. The combined sticks passed the test where previously, while configured in DIMM#1 and DIMM#2, they had failed it. I moved the sticks back into DIMM#1 and DIMM#2 to test again. The combined sticks failed as they had during the initial test.
    I then reconfigured the sticks to DIMM#1 and DIMM#3 again and booted up the system. Although I only had limited testing time last night, I seemed to be totally stable. The system did not reboot at all and I actually managed to play WoW for an hour without a single crash.
    Any suggestions on what's occuring? I figured that maybe the mobo's memory seating in DIMM#2 was messed up, but I wanted to get some more guidance from others.

    Well if it's an Antec Sl-350, that one only has 16A @ 12V, way too little to handle your system.....
    I would get another PSU in any case, as even the TP-380 is bare minimum.....
    Go for the Enermax 465 it has 33A @ 12V and then you are sure it's not a power problem...
    Also, a good PSU is never a waiste of money

  • K8T NEO FSR floppy problem

    I just got this board, here is my gear:
    K8t NEO FSR
    2 x512 MB Mushkin DDR
    74 GB WD Raptor SATA HDD
    200 GB Maxtor SATA HDD
    Plextor 8x DVD+-RW
    Athlon64 3000+
    ATI Radeon 9800 Pro
    X-Superalien case
    The problem I am having is that the system will not successfully load anything from the floppy drive. I used a known good floppy drive. If I enable floppy seek at boot it spins up and the light comes on, but it can't boot from the floppy and Windows XP setup can't read the SATA drivers disk.
    I can't install XP because I can't get the drivers for SATA to load. I have a network, is there any way I can have the sysem load the drivers over the network? HELP!

    I had a problem similar to this on a case with a molded floppy slot.  WHat it ended up being is that I screwed the floppy drive down too close to the case and the button was always slightly depressed.  Enough that I could here it click when the disk slid in but the drive failed to work properly because the disk wasn't technically in.  This drove me nuts because 3 drives failed to work all with same symptoms.  Then I noticed when I hooked one up on the side of the case it worked fine.
    Also be sure that your boot order in advanced settings is set for floppy first and then hard drive and that floppy is not disabled in your integrated peripherals section.

  • K8T Neo-FSR problems booting

    Hi
    My Computer is having problems booting. Two days ago i went to boot my computer and all the fans started up and everything seemed fine, but then nothing happened at all, but my computer was still running (cpu fan is running, power suppy fan running, red light on tower has some activity at the begining but then nothing)(my monitor light is flashing like it does when the computer is off) , so I turned off the computer by the button. Then i rebooted the system and everything worked fine. Today I went to boot my computer and this happened again, but now it won't boot at all. I have had this motherboard since january and I have never had a problem before. Any ideas of what is going on? I am assuming that it is something with bios, but I have no clue what. Any help would be appreciative.
    motherboard:   K8T Neo-FSR
    cpu: athlon 64 3200+

    AMD64 3200+
    K8T Neo-FSR
    512 MB Ultra ULT30215, 512 MB BRAVO ADM328TM-50   400mhz
    PNY GeForce MX4000 128MB AGP Video Card
    Maxtor 60 GB(Don't know specific model)
    Unknown 20GB HD
    Philips CD-burner
    Philips CD-ROM 56X
    Creative speakers
    IBM 17" screen E74
    Powmax 300 watt dual fan ATX power supply
    TRENDnet TRW-423PI wireless pci Adapter
    I have already unplugged any devices that are not needed during startup, I still have the same exact result, I tried to update the BIOS but it didn't read the drive because i'm assuming it doesn't know the boot order because that all comes the BIOS, so this is was leads me to think its something with the BIOS and not my hardware. My computer has a boot manager, I beleive its OSN??? This sits on my Maxtor drive with windows xp and solaris10 sits on the other Hard drive. Is there any more information you need?

  • PROBLEM! K8T Neo-FSR cannot instal " wd 500 32MB Cache internal hard "

    hi everybody
    i have a  K8T Neo-FSR mainboard and i bought a western digital hard ( 500 32MB Cache internal )
    but
    i cant  instal  that.
    the mainboard is update.and this is information of pc :
    Operating System
             MS Windows XP Professional 32-bit SP3
          CPU
             AMD Athlon 64 3000+   40 °C
             NewCastle 0.13um Technology
          RAM
             256MB Single-Channel DDR @ 200MHz (3-3-3-8)
          Motherboard
             MSI MS-6702 (Socket-754)
          Graphics
             L1520B @ 1024x768
             128MB GeForce FX 5200 (MSI)
          Hard Drives
             78GB Western Digital WDC WD80 0JD-00JNA0 SCSI Disk Device (SCSI)   43 °C
          Optical Drives
             WD Virtual CD 1110 USB Device
             SONY DVD RW DRU-820A
          Audio
             M-Audio Delta Audiophile
    what shall i do??   please help me.

    No, you put the jumper on the drive!
    You must enable OPT1 (jumper pins 5-6).
    However do be warned that your mainboard uses the Via VT8237 southbridge chipset, which has known unfixable issues with SATA 3.0gb/s. You may have luck with the drive jumpered to 1.5gb/s, but it may still not work.
    See: http://wdc.custhelp.com/cgi-bin/wdc.cfg/php/enduser/std_adp.php?p_faqid=1337&p_created=1112379341
    And elsewhere: http://www.google.co.uk/search?q=via+vt8237+sata2

  • K8T Neo FSR Unusual Power Supply Problem

    Hi folks! I've been using my Neo mobo for a couple years now. Recently I noticed the 3.3V line was dropping. It steadily over a week's time went from 3.3 to 2.6. At 2.6 I was getting constant artifacts and instability. Thinking of course that it was the power supply's fault, I replaced it. This one lasted two months, but just like the other, started off fine, then 3.3 slowly dropped to 2.6.
    Is there anyway this can be something other than the power supply? I'm utterly confused; two power supplys shouldn't die slowy on the exact same line.
    Thoughts would be greatly appreciated.
    Thx!
    Edit:
    Realized y'all need more info :P
    athlon 64 3000+
    radeon 9800pro
    two harddrives
    one optical
    sound blaster audigy
    K8T Neo FSR mobo
    1st PSU: Aspire 550W, 34A on 12v and 28A on 3.3v
    2nd PSU: Generic 500W, 28A on 12v and 26A on 3.3v
    Edit 2: Just a note, ALL other voltages were stable. It was ONLY the 3.3v line that droped.

    Quote from: Bas on 30-January-06, 05:16:17
    The onlything that could cause that is bad-connection between the connectors....ergo like not pushed in far enough....
    (could be because of fluids too, but I find that rather unlikely)
    Both those cases seem unlikely...I know for a fact there were no fluids, and I'm 99.9% sure the cable was inserted properly. Doesn't it mean something that it was ONLY the 3.3v cables that were burned?
    BTW, what makes you think it's the video card? Since it's getting power from a molex that only has 5v and 12v lines, why would it need 3.3?

  • Sempron 64 3000 on MSI MB K8T NEO - FSR

    I have a problem with MB MSI K8T NEO - FSR. When I put on CPU Sempron 2600 SDA2600AIO2BA, it works fine and the MB detect it fine,
    but when I put on CPU Sempron 64 3000 SDA3000AIO2BX, the MB not recognize the new processor and reports AMD Unknown Processor.
    I have the latest BIOS on the mainboard, but the problem remains. Can someone help me who had the same problem?     

    Cool and Quiet for one. C&Q is not working from my understanding on the Semperon 64's ATM. There is also a fix shown by one other gentleman here in this forum area about removing a file that is associated with C&Q functions. CPUSlowdown or some such. I don't have a Semperon 64 so I can not confirm this though.

  • K8T Neo-FSR will not boot Windows XP

    Hello,
    I just finished swapping out my old Asus P4B266 motherboard for an MSI
    K8T Neo-FSR.  I plugged all my old components into the motherboard and
    started it up.  I can get into the BIOS and everything seems to be ok
    as it detects all my drives (Seagate 120 GB IDE, Zip-100, Floppy 1.44,
    Creative Labs DVD and Plextor DVD burner).  However, after exiting the
    BIOS, I get the screen that tells me to select how Windows XP should
    start (safe mode, safe mode with command prompt, safe mode with
    networking, or start normally).  This is where my problem is.  I
    cannot get Windows XP to boot regardless of which option I choose.  I
    really do not want to have to reformat my drive.  If anyone has a
    solution or suggestions, it would be greatly appreciated.  Thanks in
    advance.
    Current hardware:
    K8T Neo-FSR
    Athlon 64 2800+
    512 MB Crucial PC3200 RAM (non-ECC, unbuffered) CAS=3
    120 GB Seagate IDE Hard Drive
    (trying to load) Windows XP with SP1

    Hi
    Not a lot without BIG risk of losing some data. If you have mega important files, you will of course have several backups, and backups of back ups.  
    So you could slip another HDD in a bay and plug the cable from your Sys HDD into it. Then install OS to it, and use it to check and repair your IMPORTANT HDD, after, of course, you have done ANOTHER BACKUP. you may be able to use disk management or device manager to fix MBR and boot files.  As your offending HDD and the old C: partition, will will have a new Partition letter now, you can use XP CD repair facility of repair your previous installation. You will of course lose IE and OE info and settings, but not a lot else. But there again havng back up to Express Assist all your emails,OE settings and accounts along with all yout IE settings and data, will be restored at the touch of a couple of keys.
    cheers
    jocko

  • K8T Neo-FSR showing incorrect CPU temperature

    Hello. I recently purchased a K8T Neo-FSR, which came with BIOS v2.2 installed. For some reason, it wouldn't allow me to set my own memory timings (it always used the "safe and sane" SPD values, according to CPU-Z, regardless of any BIOS settings I tried). I wasn't about to sit back and let my expensive new memory go underclocked, so following some advice I found on an obscure German forum, I installed the v7.1 BIOS from MSI's global site. That fixed the timing issue, but now the board is reporting incorrect temperatures for my CPU. It usually fluctuates between 23-26c, but will occasionally rise to nearly 30c and then immediately drop back down again. Case temperature remains stable at 27c. When I first installed the board, the temps were right around 45c, almost 20 degrees higher, which seems a lot more accurate to me (though this was also before I upgraded the crappy heatsink).
    Is this anything to be concerned about, and is the CPU temperature supposed to constantly fluctuate like that? I'm worried that if my fan fails or something else goes wrong, the sytem won't react until the temperature is 20 degrees OVER the safe limit. I have a feeling it interferes with the Cool n' Quiet functions, too, though my CPU fan (Thermaltake Venus 7) has its own built-in sensor and adjusts itself automatically anyway.
    Aside from the temperature wackiness, the system is rock-solid and runs like a dream. Specs are in my signature.

    There are 754 Venice's out there as NewEgg sold them at one point from what I gather as I was looking at what was the best 754 but settled for the Clawhammer.
    I have just stopped using CoreCentre on my XP as it started to show extremely erroneous and frightening temps so I ran MBM5 in conjunction as well as used my Cases thermal probes and guess which one was wrong...?
    This was after seating and reseating the cooler, CPU, memory many times and it was only on Asetek's forums that reminded me that I should maybe do some independant tests by taping probes on the cpu's board as close to the core as poss, a difference of twenty degrees no less.
    CoreCentre seems to have got a bit lost and a tad annoyed as I cross checked after buying the components for a 1/2" inch custom watercooling setup.
    Now this is the current temp and voltages I get:
    The 45 degree high was me using Prime to "cook" the thermal paste as I had to reseat the Artic Freezer 64 as it had dropped a touch.
    My ClawHammer is for some reason one of those that never had a heatspreader which of course leads to difficulties with such coolers as the Freezer 64 Pro.   Does anyone know where I can get another spreader or should I just leave it...?
    I am not going to o/c this CPU to be honest, since sorting the temps out and once the watercooling is on, 3.2Ghz is plenty good for me for the moment and bearing in mind the Neo's touchyness about settings in BIOS I am very much considering now to roll back the BIOS to 1.9 as it was 2.2 that started causing the problems.
    As for the memory timings, my Neo is totally ignoring any attempts to change the timings of my memory, I had to part company with my XMS Crucial sticks because the Neo had all sorts of problems and running some of the best memory at DDR200 was pointless.
    AO

  • K8t neo-fsr - starts playing computer static?

    I just got an Athlon 3400 and a k8t neo-fsr from Newegg.  Put XP on it, tossed in a new NX6600GT (also from MSI), a stick of GEIL 3200 512mb RAM (which is another story) and everything seems to work - except that sound "freaks out" after dealing with the computer for a bit.  Everytime I've done it I've been in Explorer, and clicking on something.  The static sounds like you're playing a CD-ROM in the stereo, crossed with modem noise (no, no modem installed - the only extra card is an extra NIC that I needed initially to get drivers). 
    I've run the live update and that doesn't seem to have helped at all - new bios, drivers, etc.  Still does it.  If the computer just sits there, no problem, but after I interact with it for a while it starts, and it takes a reboot to fix it.  I played Max Payne 2 for an hour a couple of nights ago without any problems, for what it's worth. 
    Anyhow, this is the damndest thing, and amazingly irritating.  Anyone have any ideas?  I tried searching but didn't see anything appropriate.  Thanks.

    Is is still the chipset in control and if you notice this is made for our chipset working with the AC97 chip. Just try it. If it does not work then uninstall it and reinstall the AC97 drivers. Or yuou can read about it on the Via site. They can give you far more info than I can. All I know is that it works and does so better than the AC97 drivers.

  • [Athlon64] MSI K8T Neo FSR / Early Chipset Initialization

    Hi There,
    My MSI K8N Neo Platinum has a broken LAN interface, i don't have the papers of it so I can't send it for RMA. So i bought a MSI K8T Neo FSR.
    But there is a problem, when i power up the system, the fans are spinning, the hard disk spins up and the CDRW/DVDROM drives are working. The only thing the system does is hanging at the "Early Chipset Initialization" state accoding to the D-Bracket.
    - Tried an other VGA Card > No result (Radeon 9200, Club3D)
    - Bought other memory (I do have 1GB now , but still no result)
    - Tried resetting the BIOS > No result
    - Tried removing the RAM, the system beeps there's no RAM in the system, but when i put it back in the system wouldn't boot again.
    - Tried to boot up only with R9200, CPU and RAM, and still it won't work.
    - Tried to boot outside the case, but still no result.
    I tried my processor, memory, PSU and vga card (6800LE) back in my K8N system and it works great, so i don't think my PSU is too weak.
    And I aint thinking that my motherboard is broke, it still beeps without memory in it.
    I am getting really confused, i'm out of money now so i can't buy some new stuff.
    Anyone ideas?
    Specs in signature. (PSU 18A @ 12V), sorry for my bad english. 

    Quote from: fafner on 03-May-05, 20:55:16
    Why don't you get a PCI network card for the K8N system?  No need to fuss around with a new mb just to get a LAN connection.
    Don't want to use PCI-Cards
    Quote
    Have you tried removing the RAM and then doing a Bios reset? Sometimes things get sticky if the RAM is still in place during a Bios reset.
    I would also unplug anything that is not entirely needed to boot so you can simplify the problem.
    Another hint. As the RAM controller is inside the CPU the system will not do anything right without RAM. The CPU will imediately hang.
    Just tried a BIOS reset without RAM in the system, the system won't boot. Only the CPU, VGA card and the memory is placed. Only the 4pin 12v and the 20 pin is connected.
    It just won't work, maybe the board is dead?

Maybe you are looking for