K8T Neo Usb Prob

Hello, one day i came into my room and Turned on my computer to use the USB feature, well i thought my USB Disk broke, i went to get another one, came home Put it in and it didnt even register as me putting it in the system, other USB Devices work like a game pad and my keyboard and mouse, i tried to upgrade to SP1 For Windows XP and that didnt help, any help would be Gladly appreceatied .

Is this a front USB connector on the case? Are you plugging a USB 2.0 device into it? If so, it is good you put SP1 on since it is needed for USB 2.0, and many comp cases have been reported as having a quirk in the wiring. Here is a response I've given in many USB threads:
Quote
Frankenputer wrote:
Check to see if there is a wire running from your Front USB ports to the #10 slot of your USB block which connects to the motherboard header.
USB connector block layout which corresponds to the pin layout on boards with the Intel spec for USB. Do not cut the pin on the MOBO. You are removing/cutting the wire to the connector block from the case.
2 4 6 8 10(this wire, #10, not needed)
1 3 5 7 9(filled/key)
If you find a wire leading to the #10 spot on the block, remove that wire. My block has tabs so that you can pull the wire out, or you could snip/cut the wire leading to that position--if you cut the wire, be careful to cut the correct one and cut it in such a way that it may be repaired if you make a mistake. Make sure you wrap the wire, the exposed end/s, you remove/cut with electrical tape so as not to accidentally cause a short. I actually folded the wire back and wrapped it.
2 posts to read--Here and Here.
This seems to be a common issue involving many different case manufacturers. I don't know how it applies to other MOBO manufacturers, but in these forums it is not limited to a specific MSI model or supported chipset(Intel or AMD).

Similar Messages

[S754 MSI K8T NEO] Some onboard usb ports are 1.1 instead of 2.0 ?

I own a socket 754 MSI K8T Neo FISR2 mainboard. Due to a lot of USB devices I'm using all ports and it seems like some ports are USB1.1 instead of USB2.0 The manual tells me this mainboard has 8 USB 2.0 ports, but only 2 out of 4 onboard ports at the rear (beneath the PS/2 connectors) seems to be 2.0. At 1 internal connector I do also have connected a frontside USB connector which is 2.0 and at the other connector a memory card reader which also seems to be USB1.1.
Can someone explain me this is a 'feature' of this board or do I have to upgrade a driver or something?
In the bios I have enabled all USB-ports and I'm running Windows XP SP2. With Windows Vista Beta2 I even can't get those 'usb 1.1' ports to work.

It's already solved. I just found this topic: https://forum-en.msi.com/index.php?topic=73390.0
I had to unplug one of the wires (which is connected to pin 10) of the frontside USB connector form my antec sonata case.

Where is board temperature probe seated on mobo K8T- Neo - FIS2R

hi All
I would like to know where board temp probe is seated on my mobo K8T - Neo FIS2R
MSI K8T-Neo FIS2R
AMD64 3400+ Clawhammer @ 2310 Mhz
NORTH Q Silent Ice II NQ-3100 With Ceramic fan bearing
Leadtek Winfast A400 256 Mb DDR3 G-Force 6800 GT @ 400/1100 Mhz
1 GB Cosair DDR RAM
NORTH Q King Kong Extreme 500 Watt
Aopen CD-RW 52-32-52
Maxtor 160 GB 8mb 7,2 Rpm
Maxtor 80 GB 8mb 7,2 Rpm
Maxtor 60 GB 8mb 7,2 Rpm

Somewhere close between the RAM and the Winbond chip as near as I can figure.

Probs with k8t neo and radeon 9500 non pro

Hi!
I´m totaly new with amd and i got a msi k8t neo and a sempron 2800+ with 1gb memory and a saphire radeon 9500 non pro and the computer does not start with that graphiccard.The processor fan just spins up a bit then it dies. But with a gforce 5200 card the computer works fine. I have tryed the saphire card in my server with a P4 1,6ghz and on that motherboard it works just fine.
Im from sweden so my english is not the best ;-)

Quote from: qTj on 17-November-05, 20:25:05
Yes i have tryed all those things. But my card works perfectly in 2 diffrent computers. So i dont think that the vidccard is broken.. But what do i know...
Well you know that othergfx cards do work oin ur board, so I still say you RMA it, or swap if with another card that will work
Quote
"drulleförsäkringen"
translates like "fools insurance", apperently in Sweden U get a refund when u buy something and wreck it

New K8T Neo FIS2R won't post

I have looked at all the other threads in this forum, but can't find the solution.
Specs:
New K8T Neo FIS2R
New A64 3000+
New Mushkin 3500 Level One (Cas 2) 2x512MB
New Antec 550 (24A on the 12V)
ATI Radeon 9800 Pro
When I give it power, all the fans come on, the 4 LEDs on the bracket stay lit up, and then don't change, but I get no video or any other indications (such as beeps). The 4-Pin power connector, is securely connected in the proper location. The standard ATX connector is also secure. I'd link to a picture to prove it, but my camera is charging right now.
Currently I have only power wires, power switch, system speaker, video card, and 1 stick of RAM in the first slot. I have tried it without the video card, without RAM, with RAM in different slots, just about any combination I can think of. I have even cleared the CMOS a few times. Nothing changes, I always get stuck with the 4 LEDs. I don't have anything connected to the USB headers either (that was mentioned in another post).
I know some people have mentioned that the Antec 550's 24A on the 12V isn't great, but it should be more than enough amps, the way my system is setup right now.

Hi
It does not sound like a major prob, it sounds like a PSU or memory problem, anyway of checking MOBO with another PSU with at least 20A on the 12v. Also check the memory sticky at top of the posts and see if your OK memory wise, another possibility is that one of the mounting screws is tracking from the board - try removing screws and see if it boots, also check none of the cables are touching the case or MOBO.
MOBO and CPU seem fairly resilent, so faulty parts are not to likely, although one never knows. Another thought the Jbat1 Cmos jumper is on pins 1 & 2, 1 is marked on board, and you could try clearing CMOS. a corrupted bios could also cause this.
Best of luck, lets know how you go
Jocko
PS. looking at the stickys at top, Bas has put one there about a compitition by MSI, one of the questions is about Radeons needing extra power( has an April 1st entry date!!), it is worth checking, does your Radeon have its own supply, you could always remove it and see if it boots.
Cheers

My Unofficial K8t Neo Guide

Disclaimer: You try any and all troubleshooting at YOUR OWN RISK!!
Here is my unofficial guide to the K8t Neo fisr2 If you Like It give it a thumbs up so it will stick out. I will warn you it is long and I will edit off and on.
to add as needed.
first I'll start off with components,
CASE..you will need an atx case with good cooling a few extra fans like a blowhole at the top can help cooling, also bundle cables and power leads
so that they don't interfere with airflow.
MOTHERBOARD,...This is based on the K8TNEO series, when you attach it to your case make sure that is is mounted to risers to keep it from contacting case, they are usually small brass pins, also make sure that all the mounting screw are secure and in place, this will prevent the PCB from flexing and cracking as you install components, there should be around 9 or so screws, that usually go into the riser pins or raised case mounting points,don't forget to use those fiber or plastic insulated washers. These should be the only case contact point to the mobo other then the back plate with all the usb, net jacks etc..
Also use all of the mount points you can..if not you can crack mobo putting in cards etc...
CPU...Athlon64 processor2800+, 3000+, 3200+, or a 3400+, all 754 pin chips...k8neo CAN NOT USE FX chips or Opterons. 3200,&3000 are basically the same chip, same clockspeed of 2.0 ghz but the l2 cache is different 3200 1mb...3000 512k, you may not notice the difference in many applications but will see 2~10% diff in benchmark testing, the 3000 is usually about $75 cheaper
the 2800 is a newer model an a good way to get into 64bit without high cost.
PSU.... one of the most overlooked and most important component,
that old 300 watter you have from your old duron 800 don't even try.PSU's have caused a lot of trouble with a64 systems, they use a lot of power Get a good name brand psu if you can, and make sure it is at least 400 watts and has at the minimum of 20a on 12v, also look at combined total wattage
the psu must have a 20 pin connector and a 4 Pin( Square) Connector, and there is Only 1, Called the+12V 4 Pin Processor Connector.
some of the recommended brands are enermax,and antec.
Here is the reason most problems are the psu
amd64 uses 12v power, Intel chips used a lot of 5v power.
so until now most big psu's pushed 5 v not 12v
almost everything in your computer uses 12v except ram (3.3V)
AMD 64 and motherboard =12a @12V
so your already at 12A with no fan,s no hd, no CD,no DVD ,no mobo chip-set , no mem, no sound..etc
so what happens is your mem gets starved for power and then gives out errors,in your data, which = corrupt sata,or it fails to post. .
MEMMORY...Another big trouble spot,not just with the MSI board but with Via chip-set, and or the A64 memory controller.
DDR non ecc- single channel 400 is baseline although slower chips also work, The CPU's memory unit only supports 4 banks total so in order to use three sockets at least two of the memory sticks have to be 1 bank,.one bank or two bank chips look similar so check specs, dual bank chips usually have chips on the back as well. mem should match type and speed. if you run into problems try going into bios and limiting ram to 333.mem should match type and speed.
(edited out till i find more info [STRIKEOUT] if using two mem sticks it is best to use slots 1 and 3,[/STRIKEOUT])
edit :ok tiresmoke just replied so have a look. "One thing that often does not get addressed. I had a couple Blue Screens early on. Here is how I fixed it. I run my RAM in sockets 1 and 3. 1 and 2 gave a little instability.Yes I decided to keep mine in slot 1/3 but I did test in 1/2 since I changed Bios. Typically slot 1/3 can slow you down but it did not with mine so best to say that difference RAM will give different symptoms. Try combinations to find what works best for you."
LOL Keep in mind that Jocko uses 3 sticks of dual bank RAM and according to AMD they only support 4 banks total. Jocko has 6 so you do the math.
you can check msi's website for compatible ram, but be careful it can be confusing,
they list by part numbers,
but some known configurations that work are:
I would stay away from corsair xms mem right now many people have problems.
corsair and kingston owners may want to look here
AMD 3000+ systems...
BIOS 1.2
2 x 512 - Corsair CMX DDR400 @2-3-2-5
2 x 512 - Corsair Twin Pro DDR400 @ 2-3-2-6
2 x 512 - Corsair Value Select DDR400 @ defaults
1 x 512 - Geil Golden Dragon DDR400 @ 2-3-3-6 (2.7V)
2 x 512 - Hynix DDR400 @ 2-3-3-6
2 x 512 - Kingmax DDR433 @ 2.5-3-3-6
2 x 512 - Kingston DDR400 @ 3-3-3-8
1 x 512 - Kingston HyperX DDR400 @ (defaults?)
1 x 512 - Kingston ValueRam (KVR400X64C3A) DDR400? @ (Defaults?)
2 x 512 - Muskin Level 1 DDR400 @ 2-3-2-6
2 x 512 - Muskin Level 2 DDR433 @ (defaults?)
2 x 256 + 1 x 512 - Muskin Basic DDR400 @ 2.5-3-3-8
1 x 1024 - OCZ EL DDR400 @ 2-3-2-6
BIOS 1.3b2
2 x 512 OCZ EL DDR433 @ 2-3-3-7
AMD 3200+ systems...
BIOS 1.1
2 x 512 - Mushkin Level 1 Black DDR433 @ 2.5-3-3-6
BIOS 1.2
2 x 512 - Apacer DDR400 @ 3-4-4-8 (2.5v)
2 x 512 - Corsair Twin X DDR400 @ 2-3-2-6
1 x 1024 - Corsair TwinX DDR400 @ 2-3-2-6
2 x 512 - Crucial DDR400 @ defaults
2 x 512 - Elixer OEM DDR400 @ defaults
1 x 1024 - GeIL GoldenDragon DDR400? @ defaults
2 x 512 - Geil Value Series 512MB DDR 2.5-3-3-6
2 x 512 - Hynix DDR400 @ 2-3-3-6
2 x 512 - Kingston HyperX KX DDR433 @ 2-3-3-8
2 x 512 - Kingston HyperX DDR400 @ (defaults?)
2 x 512 - Kingston HyperX DDR400 @ 2.5-3-3-8
2 x 512 - Mushkin Level 2 DDR400 @ 2-2-2-5 (2.75V)
2 x 256 - Mushkin Level 2 DDR400 @ 2-2-2-5
2 x 256 + 1 x 512 - Muskin Basic DDR400 @ (defaults?)
2 x 512 - Twinx CLPRO DDR400 @ (defaults?)
2x512- Pny Verto DDR433 @defualts
AMD 3400+ systems...
BIOS 1.2
2 x 512 - Kingmax (MPXC22D-38KT3R) DDR400 @ defaults
2 x 512 - Mushkin Level 2 Black DDR433 @ 2-3-2-5
you may have to email you mem manufacturer and manually set timings and voltages to get your memory working.
HARD DRIVES......Here you have alot of choices, basically two categories, SATA and PATA(IDE). There are many brands and speeds, IDE drives come in different speeds, such as ata33, ata66, ata 100, ata 133 for hard drives, the 33,100,133, being theoretical maximum transfer rating MB/sec.
newer ata(IDE)hard drives are ata100 which is ultra 5, and ata133 ,ultra6 is ,
PIO mode is the standard data transfer mode without the ultra enhancements, the fastest being 16.66 mb/sec. ultra 2 is 33 mb/sec . So when i say my CD,DVD, and DVD are ultra 2 it means they transfer at a maximum of 33 mb/sec, and my Maxtor hardrives are ultra 6 and have a maximum transfer of133 mb/sec. my old zip100 transfers at a max of 16 mb/sec since its in pio mode. Note these are maximum speeds, my hardrive transfers more like 65 mb/sec sustained according to SIS Sandra.
That is why SATA 150 is such a big deal, vs say a Western digital ata100
SATA is a different interface all together and can transfers closer to its maximum
theoretical speed. BUT the pci bus itself is limited to 133 mb/sec so an add-on card
should never be able to reach over 133, regardless, of SCSI,IDE, or SATA
so on the k8t neo you have some choices. With the IDE you can use, IDE1,2, or 3
IDE1&2 are ata100. ) to attach use a 80pin round or flat cable, the first slot goes into the mobo, the middle connector is for a slave or should be left empty, use the end for master, or single drive. you must also setup jumpers for hd or cds.
The master is primary unit and the slave is secondary unit, for each channel.
Or use the Cable Select jumper and USUALLY the BIOS will select the drive for you.
IDE1 & 2 is ata100, or 133 depending on board if using for only 2 drives put them on different channels
...ie master on IDE 1, and master on IDE 2 . that way they will have maximum bandwidth. especially for disk to disk copies or burning
IDE3 RAID is ata133, or can be raid 0 or 1 by the promise chip. 0 being striped for performance,1 being mirrored for safety, mirror only protects hd from failure,not viruses,or corruption for that you need a backup or as i prefer a drive image program such as accronis trueimage..linux compatible.and Norton ghost.you will first have to enable the promise chip in the bios, then you have to load drivers by hitting F6 during windows installation, and insert floppy drive, yes you will need a floppy, at least for initial setup. If you want to set up raid you will have to do that first before loading windows,by hitting ctrl+F (read quick user's guide Serial ata raid, serial ata) only hd's can use ide3.If you don't have enough IDE slots you can add on pci card with one or two more headers for up to 4 more drives, I added a Maxtor ultra ata133, since i have 5 idehd's and 3 DVD/cds.
SATA, here you have two choices, use the Promise chip set or the Via. Either one or both can be set to raid0 or 1, see users guide to setup, You will also have to enable them first in bios, and F6 and load floppy drivers to use in windows install, or load drivers in windows if using an existing install. either chip-set can be set for raid, in the manual, opinions are that the Via is faster, but you wont have a HD LED activity indicator light, The promise will have a HD light, but is slightly slower.
Also note that SATAs don't OC as well as IDE hard drives, they can even crash and loose data.
always make a backup of your computer, and remember raid 1 does nothing for virus, or contaminated installs.
SOUND....Here you have a few choices, On board or Card, unfortunately not both, yet.(UPDATE Bios Version 1.5 and above will fix this)... If using a card there have been some issues with Audigy 1 cards, but there may be a cure in this threadhttps://forum-en.msi.com/index.php?threadid=46849&sid=( Moved to stickies) audigy2 and 2zs cards work fine as do turtle beach.
on-board sound is not as high definition and uses some CPU cycles, so a card might be advantageous to gamers.
REALTEK GIGABIT...Is the on-board Ethernet, you will need to load drivers once in windows, it has caused some problems booting, as it can be set to a boot device as well. you will get a message "failed to boot press any key."..then "ntdlr error"...to fix this you may need to hit the key combination during boot to set it up, it will bring you to a menu, you need to set boot order, i recommend setting it to bios, and you can adjust or disable message and time length it is displayed.
VIDEO CARDS- You should install an agp 8x directx9 video card for best performance. Ati has better directx support so is better for gaming, but Nvida has better OpenGL so if you want to do 3d in Linux, you have better luck with Nvida.
When you set up windows, install via 4-1 drivers first, then the video drivers, check video manufacturer's website for updated drivers. make sure any extra power leads are plugged in. In bios Agp should be fast write enabled, and
if you are using 1024 of ram aperture size to 256, but check 3dmark to see which setting is faster.
BIOS- NO BIOS INSTALLED This is a message that you see during boot up from the promise on-board raid saying that it found no drives attached to its SATA or IDE channels so it's not installed the BIOS.This IS NOT a problem or anything to worry about!
jumping Bios reset jumper, be careful, make sure power is off. jump it and return it to the original position. If you power on with jumper in reset position you can erase your bios...requiring a Return to Manufacturer Authorization(RMA)
I have had no problems using windows updating to the latest bios ,It cured some issues, such as firewire ports, sound blaster audigy1 troubles,tweaked temps displayed,and so on. but be sure to have a backup of original bios disk. I have heard new 1.8 beta bios cures Newcastle temp problems.
some good settings are.. SMART enabled this will warn you of hard disk failure,System bios cacheble and shadow ram are more for older computers and should be set to disable.boot to os2- disable...memory setting vary by card and some even need to be set manually so check with manufacturer or get familiar with cmos reset jumper.(just be sure to have power off)...plug and play os to disable(more of a win 98 thing) disable serials and parallel ports if you don't need them, as with on-board sound firewire etc. this is just a few pointers the rest is a more personal thing, but i have heard turbo setting causes problems and is best left to fast, and dynamic oc'ing is similar use at your own risk
USB keyboard don't forget to enable USB in the BIOS. This caused some problems when installing XP. Without USB enabled in BIOS when you come to the "Hit any key to proceed" the install will fail with the ntldr error
POWER SAVINGS...Having trouble getting fans or case lights to shut off on standby set to S3, then disable apm, and be sure to set a wakeup event..such as wake from usb, or keyboard command. I have agp boot disable, but depends on card.
Want to know more about bios, and what those settings are? click this link
http://www.rojakpot.com/(eb1mg5zatgcf5r55lv5no155)/default.aspx?location=9
CORE CENTER....Another personal choice, I like it and use it a lot, to increase and decrease fsb without going through bios. the NB fan sensor should read 0 unless you plug a fan onto it, personally i have an 80mm antec and it doesn't read it, but i tried a old CPU fan and it worked fine.
COOL AND QUIET Another personal choice, I don't use it because some people have had there CPUs power down in the middle of games, and such
(it goes down to 800 MHz) others had small bugs in there system that went away when they disabled it. But some like it and use it a lot. Good for energy savings.
want to get your boot time down
start by selecting OS drive as first in boot sequence, you can always change bios when you want to boot from floppy or CD(which isn't often).disable floppy drive seek
then clean out your startup folder under rt click explore start button.
try and get services set to auto down to about 25. defrag your hdrive routinely,
. ditch wall paper, and get rid of windows startup screen.(msconfig,boot.ini.and check noguiboot). keep your drivers updated
if you can find it you can use then try bootvis, but microsoft doesn't support it anymore.Programs ..some useful free utilities are listed below, check goggle, until i make links for them.
SiS Sandrahttp://www.sisoftware.net/, a good all around benchmark,burn in and, info display
3DMARK.http://www.futuremark.com/download/.Mostly a Video tester, good for checking OC though.
Microsoft Memory testerms memtester
+86memtest.http://www.memtest86.com/..and Prime95http://www.mersenne.org/freesoft.htmvery good mem testers, and tests for stability
spybot search and destroy, http://www.safer-networking.org/index.php?page=homeand
Lavasoft's ad-aware http://www.lavasoftusa.comgot to have for house cleaning.
atitool, http://atitool.ocfaq.com/oc ap for ati cards,click find max core let it go for 15min or so,then set back to default, and click find max mem...for 15min or so, and now you have the max you can set your video card too.(but set safety limits before manually setting)
[STRIKEOUT]mbm5 mbm5 link good alternative temp readings to corecenter.[/STRIKEOUT]
good program but discontinued.
OTHER USEFUL PROGRAMS
Norton utilities, good all around disk and OS utility
Norton Internet secuirity, or similar firewall and virus protector
Norton ghost, or other drive image software fantastic for backups
BF1942...lol just fun
HOME NETWORKING I will add this part because of additional posing of errors
dealing with USB Broadband routers...try using on board realtek or other Ethernet connection it will save your sanity.
well i have a real poor mans router setup for you
2 Ethernet slots, one for for broadband router and one to share.
if you only want one other computer, use a crossover cable, otherwise, use a hub or switch(better) and let Internet connection wizard and home networking on your machines work their magic,want a firewall download some software there are even, fairly decent free ones.the speed of the card isn't important because broadband still isn't over 10mb/sec yet, so blow the dust off that card in the closet and put it to work.or if your really brave or really cheap you can try to use the usb input from broadband, and on board ether, or firewire port, to link computers
Trouble shooting
for total no boot/post failure
I know you may know how to build a computer, and i know this is basic, so bear with me here, but at this point you have to do a methodical by the book check list.
revision
A: when you first install your motherboard make sure it does not contact case,
use all nine mounting points, make sure that your case either has built in risers, or use the small brass standoffs, and don't forget the fiber washers.
when you installed your CPU you:
1 ___you properly handle equipment so no static damage can occur, (properly grounded)
2____.you fully lift the CPU ziff socket arm up, orient the gold triangle marking arrow,pins and it easily dropped into socket, with no bent pins ,
3 ___ backer plate mounted carefully no missing pieces of the board flying off, ( i have seen people launch capacitors, and the like )
4 ____obviously you removed the plastic thermal pad cover, and heatsink was evenly locked down, and fully seated, and correctly plugged into mobo cpufan1.
and you fully removed old thermal pad/grease and applied new artic silver, or new heatsink with plastic on pad,you didn't reuse old paste or pad.
memory
5 _____memory stick(not sticks, at this point you just want to get it working, not full blast with a gig of ram etc)is fully seated and properly oriented in slot, and is 184 pin ddr non-registered , non ecc ram , and you have tried different non corsair, non twinmoss, brands that have been known to work. and/ or
tried to set manually mem speed/voltage for some models of corsair, twinmoss, and kingston)
6.____ plug in only power switch pins 6,8and power led to jfp1, pins 2,4 and they are turned correctly,
7. ____your new psu has the 20 pin and square 4 pin power connector plugged in to jpw1 turned right and fully seated. and has a bare min of 18a on 12v+ rail.
8 ____your video card is fully seated an locked down,also securely screwed in.
9 ____your floppy drive cable iss facing right way (pin1 is matched with red stripe)
10. ____you have ata cables for hd and CD set to master/slave or cs. with hard drive set as master, end of cable.
11 _____the power plugs are all fully seated, including psu rear plug,floppy ,hd, and CD.
12. _____keyboard(ps2) and mouse plugged in, monitor plugged into video card,
13 ______every thing is fully secured in case, side cover is off.
14 ______CMOS jumper is set 1,2 keep data, all usb stuff is unplugged, except for dbracket.
power it up, one beep, fans spin, in psu and CPU, and video card,
you get no bios found error,(promise adapter not finding satas..no worries)
or hit Del to go into bios, set boot order, and .......
.........your now at the end of the road, and it should by all means work,
now what i am after,
there are no bent pins, on CPU, you reapplied artic silver paste.
no loose wires,
properly applied heat sink with fan cooling,
you have tried different brands of known ,to work in an MSI k8tneo
ddr ram 1 stick at a tme.
you have tried different video cards, and in case of higher end card, the external molex power supply as plugged in,
you have tried different ata hard drives
you then have tried have set up your SATA drive correctly .
everything is securely plugged in ..fully seated and oriented the right way?
what are d-bracket error light, and any beep codes?
you have tried a different wall outlet, you have changed surge protectors,
you never hot plugged video cards, hd cables or power etc.
i know this redundant , and basic , it is not meant to be insulting , it is meant to be a checklist and rule out all basic errors and potential problems
if your mem bandwidth is slower then 3000..like 2400 this may help
Received from a user - Slow memory 1T Command fix
OK, here's what to do. Download the following ftp://ftp.vector.co.jp/pack/win95/hardware/other/wpcrs120.exe extract it, and run InstDD.exe. It'll ask to reboot, you don't need to do it right away, at least I didn't have to. Fire up WPCRSET.exe and do the following. Under startup, click on start, and under device, click enable. Now click add. The bus device and function will be 0,24, and 2. The register and data values will be the 93,08. There we have it! Enjoy everyone. I know I'm much happier now.
Here's a graphic to make it easier:
I will add more by edit, or post as needed but i should post now so it can be put to use.
I would like to Thank BAS,wonkaboy, Jocko, ethereal, Tiresmoke, Reilly, and the many others whose valued input helps solve problems.

Quote
amd 64=12a @12V
ati 9800=7.5~10.5a @12V (assuming 90~125 watts) a max load,
a 9600 ir nvida 5200 used far less power
so your already at 18a with no fan,s no hd, no cd,no dvd ,no mobo chipset , no mem, no sound..etc
If you exclude the motherboard, memory, etc like you did there, the amd 64 draws 7.2A @ 12V.
90~125W for an ATI 9800?! [irony]Are you working for a PSU manufacturer or what?[/irony] That's just absurd.
Go read this post to get a feel for the actual power consumption: https://forum-en.msi.com/index.php?postid=297061&sid=#post297061

Cannot re-boot after enabling K8T Neo LAN Connection

I've tried to enable the K8T Neo LAN controller in BIOS so that I can connect a Wireless Router to my PC. However, when I do this, the PC will not boot and I have to disable the LAN controller.
On booting-up the BIOS seems to be looking for an ethernet controller and a message states that either the device is not plugged in or the cable is faulty ! Why should enabling the onboard LAN controller affect the device the BIOS boots from ?
Can I plug a Wireless Router directly into the RJ45 LAN connection on the K8T Neo and if so, how ?
Thankyou for any helpful advice

Check to make sure you are not set to boot from network. Unfortunately I can't remember the exact name or where it is located, but it may help.
Quote from: Geps on 07-July-05, 22:52:17
as you say: a WIRELESS router is WIRELESS, how could you plugin a cable from a wireles router. or does it also have rj45 conectors?
if you want to use the wirreles function, you will need to buy a wirrles lan adapter (usb) for your pc
I have never seen a wireless router without rj45 connectors. (WAP yes, router no).
Good Luck
Jeremy

6600GT not working with K8T neo-FIS2R

I recently returned a K8T NEO-FIS2R MB for repair. The problem was that the PS/2 and USB ports were broken. However the MB has been returned and the PS/2 and USB ports work fine. I posted about this several months ago.
Now the AGP port seems to be broken (not the actual slot). I have tried a 6800 Ultra and a 6600 GT (AGP version) GFX card in this slot. Both cards fail at the driver installation point. I have tried driver versions 66.93, 67.02 and 67.03. I also tried 3 versions of the via drivers 451, 453 and 455. Even tried XP with SP1 and SP2. The PC will sometimes BSOD, reset, won't boot into windows. The drivers sometimes install then other times they won't, etc. The problems only seem to be with the drivers for the GFX cards.
The 6600 GT works as I have tried it in another MB without any problems.
I know the memory works fine as I used memtest86+ for a couple of hours on the default settings without any errors and it works in another PC.
The spec of the PC is:
XP pro
K8T NEO-FIS2R MB
512MB corsair XMS at 2.5-3-7-3
XFX 6600GT
40gig HDD
FDD
Plextor CD writer
DVD Rom
PSU is a Q-tec 550W
I know Q-tec PSUs are not up to much from what I have read elsewhere in this forum, but I have had it running in a similar system with the 6800 Ultra installed without any trouble (even with the above MB before it went faulty). I have also tried a 400W PSU, that came with the case. The Voltages on the 12V line are between 12.00 and 12.03 when using the Q-tec PSU.
Has any body else had these problems with the 6600GT in the mentioned MB.
Also, how can I check the serial number on the MB with the label on the box, as this MB that was returned to me looks to “clean” to be the one I sent away for repair.
Thanks for any help

Hey, I'm glad to see a post on the new Gforce 6600GT AGP card. I just recently put together a brand new system (see my sig for specs). System runs great. The only thing I wanted to do was replace the video card, and after a great deal of anxiety I decided the Geforce 6600GT AGP was the best bang for the buck.
Well I got home, installed the card and never get passed the bios screen. (shows your processor, memory, memory siz), the screen u hit DEL to go into the bios.
The system doens't lock up, NUM LOCK can still be turned on and off, and CAPS can be turned of and on... but thats it. Just sits on that screen. I can't go into the bios either.
what settings do I need to do prior to isntalling this card to get it to work.
Let me know if you all need anymore details to help me out.
oh, I did reset my frequency to 10x200 (which is what I think the 3000+ is supposed to be at).

HEAVY Problems with Linux x86_64 on K8T Neo

Hello, Community!
I experience *HEAVY* Problems with Linux on my MSI K8T Neo (FSR). Since the customer support of the german dependancy seems to ignore my call for help I'm in good hope that maybe you can help me out or give me some useful advise.
First some Hardware Specs of my system:
MSI K8T Neo FSR, Rev 1.1, BIOS 1.5
AMD Athlon 64 3000+
3x 512MB Kingston DDR400
Enermax EG365P-VE (350W) PSU (3.3V/5V 185W Combinded)
MSI GeForce FX5200 TDR 128
Adaptec ATA RAID AAR1200A (HPT370A) in PCI Slot 3
Hauppauge WinTV PCI in PCI Slot 5
Maxtor 4K040H2 (40GB) as Primary Master
JLMS XJ-HD166S DVD-ROM as Primary Slave
LiteOn LDW-411S DVD+/-RW as Secondary Master
LiteOn LTR-52327S CD-RW as Secondary Slave
2x Maxtor 6Y060L0 (60GB) on HPT370A as Primary Master/Slave
Seagate ST380020A (80GB) on HPT370A as Secondary Master
Maxtor 32049U3 on HPT370A as Secondary Slave
KeyTronic KT2001 USB Keyboard
Microsoft Optical Wheel Mouse Blue USB
I've downloaded Fedora Core 1 x86_64 as well as the lately released Fedora Core 2 test 3 x86_64 distribution. Both CD sets have been burnt ok.
If I try to install Core 1 x86_64 (Kernel 2.4.22-1.2179) the kernel crashes with a "attempted to kill idle task" panic. As far as I've learned the workaround is to give idle=poll as kernel parameter. This resolves the kernel panic, but the installer randomly crashes with segfaults at a random stage; sometimes while loading anaconda, sometimes during package install.
If I try to install Core2 test 3 x86_64 (Kernel 2.6.5) I get a, completely new, error message while the kernel does the PCI Scan:
******* Your BIOS seems to not contain a fix for K8 errata #93
******* Working around it, but it may cause SEGVs or burn power
******* Please consider a BIOS update
******* Disabling USB legacy in the BIOS may also help
I removed my USB keyboard, connected a PS/2 keyboard, disabled to USB Legacy option (I need it enabled in order to use Ghost) in the BIOS and booted again.
The error message is gone now, but as in Core 1 the installer still crashes randomly with segfaults. I'm still unable to go all the way through the installation routine.
I even tried to install Fedora Core 1 "i386": again there are segfaults during install.
Contrary to the problems I experience while trying to install Linux my Windows XP (32-Bit), as well as a test installation of Windows XP 64-Bit, run like a charm without any problems. Strange but true.
Since I already read trough several posts in this forum I already tried running my system with memory sticks from another manufacturers as well as with a more powerful PSU. I even removed my tv-card and raid-controller.
Nogo - Linux still crashes randomly and Windows still works without any flaws.
Has anyone a clue what I can/must do to successfully install Linux?
Might it be that the BIOS has some flaws that might cause the problems?
Has anyone managed to install Linux (what distribution) on this Mainboard?
I would greatly appreciate any help. If you need to know something I haven't provided here please feel free to ask. I'll answer ASAP.
Thank you in advance.
P.S.: The system is *NOT* overclocked in any way.

And now even the last problem is solved ...
Since I was successful in installing a basic Gentoo system but still failed to install Fedora I reflashed BIOS 1.5. This time I cleared the CMOS by unplugging the PSU, setting the jumper and removing the backup battery.
Yesterday I only flashed it with the /a switch, which should have cleared the CMOS as well - so far for the theory. However, it once went fine as I upgraded from BIOS 1.1 to 1.4.
After setting up the BIOS options again I gave it another try and booted from Fedora (Core 2 test 3) install CD: No more complains about the CPU errata, although USB legacy is enabled, and I even went through the installation without any problems.
It seems as I will stick with Gentoo as my primary distribution since the kernel makes a more "mature" impression than the one from Fedora (i.e. the K8 PowerNOW! Driver seems to be missing in Fedora's Kernel 2.6.5).
By using an spare Athlon XP Mainboard I worked out that only one of my three Kingston memory sticks had errors - I'm going to replace the faulty stick tomorrow.
Now for the conclusio:
Thanks, especially you JLP, for helping me with my issue. Without the advise to use Gentoo, and the included MemTest86, I wouldn't have been able to track down the error to a faulty memory stick that fast since Windows always ran fine.

K8T Neo-FIS2R - P20378 Sata Controller option missing in BIOS. Cannot disable

A few hairs left....& those are disappearing quickly.......!!!!
I currently have Windows XP PRo running under a Promise SATA Drive. (NO RAID REQUIRED)
In order to allow for a fallback situation (which I am still using swapping between WIN XP & Vista), I found a 20GB IDE Disk attached it to the standard IDE controller & did a clean install of VISTA ULTIMATE on the 20GB Drive...So Far so good.
Next I booted up changed the boot sequence to pickup the 20GB IDE drive first ...Vista Came up....Still so far so good.
Then I found my mouse ...& both USB printers were not recognised.....2 days later I have them all going okay....one problem at a time....
The only issue left ... I cannot see the SATA Drive attached to the promise controller.....I have tried following a few of suggested methods to load the promise drivers that are around......still no luck. Most of the posts I see are around installing VISTA on a SATA drive...my case is just seeing a SATA drive this not the O/S disk.
Moving on ...no luck with the Promise Drives ...so I have tried changing to the VIA Controller by unplugging the SATA cord from the Promise controller & plugging into the VIA Controller ... I boot up & still no luck...The BIOS picks up the VIA change as I see a option to use <TAB> to setup RAID during bootup.. I do not want RAID only a single SATA Drive. One of the things I read was to turn off Promise via the BIOS settings . The manual indicates I need to access this by going to the "Onboard PCI Controller option", here I should be able to turn off the P20378 S.ata Controller...
my problem is ...I can see only the Lan Controller as a option to disable/ enable the other options including the P20378 S.ata Controller.. are not visible.. hence I am unable to disable the Promise SATA Controller within the BIOS..... HELP pretty please..... I can happily run VISTA but I do not have 150GB visible to me & my current disk space is tight.....I need that 150GB ...........
signed...frustated NOOB
PS I have the most recent drivers/ bios etc according the MSI's Online S/W synch tool (which I run in XP Pro as the vista version fails.... DOH)
MB --> K8T NEO FISR2
Memory 1GB
Appreciate your help ..... TA

I agree with Hans, as far as we know there are no drivers for Vista to use the Promise controller, yet.
Same old, same old, Vista and no drivers.
You just have to wait and hope there wil be Vista drivers for the Promise controller.

K8T Neo: Problem at power-on...

Hello!
Somehow I experience a strange startup-problem ... and I could really need some advice to resolve this issue as I'm out of ideas.
Last weekend I completely disassembled my rig for the annual "spring-time maintenance". I cleaned out dust, I cleaned the inside and outside of the case and I replaced my DVD-ROM and CD-RW drive with a LG DVD+/-R(W)/RAM drive. After everything was put together again I powered up my system - and it started to act strange.
Symptom: At power-on the system hangs at "Early Chipset Init" (D-Bracket 1-4: GRRR) and keeps on self-resetting. Several seconds (10-30) later the system starts to POST as expected and runs smoothly until ... power down.
During the night the system is completely disconnected from the power as it drains a lot of juice in stand-by (~12W for the rig + ~18W for several other external components like scanner, audio, ...).
What I've done so far to track down the error:
- Reseated power connectors. Nope - problem persists.
- Pulled all unnecessary components (just MoBo, CPU, RAM, GFX-card, Keyb). Nope - same prob.
- Pulled all memory sticks, left only one in the slot (and tried every other one). Nope - same prob.
- Cleared CMOS - Nope - same prob.
- Ran memtest86+. Showed no errors after 10+ passes.
Now I'm out of ideas ... except for the power-on problem the system runs just fine as before. No crashes, no malfunctions, no nothing.
Technical Data:
MSI K8T Neo FSR (BIOS 2.0)
AMD Athlon 64 3000+ (Clawhammer Core)
Zalman CNPS7000B CPU-Cooler
3x 512MB Kingston CL2.5 PC400 DDR-RAM (@DDR333 - 3 sticks = DDR333 only!)
NVIDIA GeForce 6600GT AGP (Power Connector is plugged in)
Highpoint HPT370A IDE Controller (PCI 3)
Hauppauge WinTV PCI FM (PCI 5)
Seagate 80GB SATA - Operating system
Hitachi 160GB - OnBoard Pri IDE, Master
LG 4167B - OnBoard Pri IDE, Slave
Maxtor 200GB - HPT370A Pri IDE, Master
Seagate 400GB - HPT370A Pri IDE, Slave
Maxtor 80GB - HPT370A, Sec IDE, Master
Tagan TG480-U01 480W PSU (3.3V@28A, 5V@48A, 12V@28A)
As I have a Wattmeter at my avail: After power-on and boot-up the system "sucks" ~315W (rig + monitor). If I put load on the system (CPU at full clock, GeForce displaying 3D) it drains ~390W.
As mentioned above I never had any issues with the system.
Does anyone have a suggestion how to resolve the rather annoying power-on problem ?!?
Thanks,
Jochen

Quote from: Tiresmoke on 06-April-06, 20:09:53
Did you checl and replace the CMos Battery? You may need to do a complete Bios Clear and start fresh there as well.
Also as the Optical drives changed did you try removing them one at a time and see if the system acts noirmally then?
Hello, Tiresmoke!
. I unplugged the PSU from the wall socket and removed the battery while clearing the CMOS. The CMOS Battery is OK - ~3.34V (reading from a Voltmeter - matches with the display at PC Health Status).
. I already took out the LG DVD-RAM drive and put the old optical drives back in. Even in its old "original" configuration the aforementioned problem persists.
. I already reseated the CPU and renewed the thermal compound.
However, I even get the "Early chipset" startup when the system is bareboned ... CPU + 1 memstick (doesn't matter which one out of the three I plug in) + Keyb + GFX. D-Bracket shows "Early Chipset Init", the boards goes through several reset-loops and fires up fine.
BTW: Maybe this will give some clue ...
. When I do a warm reset (reboot triggered by OS) the board restarts fine - Reset, POST, Boot.
. When I shutdown and disconnect power from the PSU, lets say for about 5 minutes, then reconnect it and power-on the "Early chipset init" shows up.
Are there any chances that the PSU is actually causing the problem although this particular problem never showed up before the "spring-cleaning"?
Thanks,
Jochen

K8T Neo compatible with BFG 6800 OC??

Hey all, I just got an MSI K8T Neo-FIS2R mobo and put my BFG 6800 OC (128MB RAM) into it. The boot is all fine, but after I installed win xp pro with sp2, the video became really stuttery. i installed 66.93 drivers from nvidia's site, the via 4in1 drivers from msi's site (i didn't install the agp 3.0 drivers from teh 4in1 cuz i read that i shouldn't), but after i installed the drivers it became even more stuttery.
It's so stuttery that I can't even do anything. I have to boot into safe mode to even write this.
the vid card works perfectly in my old comp so I know it isn't the graphics card.
Plz help me!!

Quote
Originally posted by Tiresmoke
Time to airmail Santa a letter, methinks.
On second thought better fax it instead.
Yeah.... Have him do FedEx overnight as well.
Get as many amps on the 12v that you can afford & you will eliminate a lot of potential probs down the road. My Enermax (see sig.) has some pretty good specs.

K8T Neo Eary Chipset initilisation hang

I've just got my MSI K8T Neo Motherboard replaced and the replacement arrived today. I plugged in the cpu, cpu fan and the D-Bracket and it seems to hang at the 'Early Chipset Initilisation.' Same thing happens with the ram and gfx card installed. I've put both the 4 and 20 pin psu cables in and in the manual it doesn't say what's wrong if it hangs at this stage so does anyone know what the hell is going on?

Quote
Originally posted by Jocko
It could still be ram, you may have to try a few.
It could also be a ground, either form a cable touching case or Mobo, or a fixing screw on MOBO touching board, no USB devices plugged in? The fans are working OK.
Other thing that can cause this is a bent pin on CPU, if you remove make sure and replace with silver artic paste or similar.
good luck
jocko
Tried several sticks of ram, don't think it'd be this though because if it does have a problem with the ram, the d-bracket will let me know if it's broken or not in place properly.
The motherboard isn't in the case atm, it's put on an anti-static sheet to eliminate this problem.
Had a look at the CPU and all the pins look alright.
Edit> Also, no devices conected at all, and fans work ok, even the gfx card so power getting around it looks ok
Thanks for help

K8T neo wont boot

I have a
K8t Neo
amd 64 2800
512 hyperx ram
ati 256 video card
and i put in a new ati wonder, restarted the computer and got nothing. Took the componet out got nothing, started taking out peice by piece untill only the MOBo was left still nothing, and i mean you know how when you start the computer the keyboard light flashes, it won't do that half the time, and doesn't get any father if it does, I have tried everything i can think of reseting the bios and cmos, putting in a diffrent video card, moving the ram, trying diffrent ram, nothing, i don't know if it's the mobo or the amd64, i don't have a usb thing with the 4 lights, so i can't use that to help.
If anyone has any thing they can suggest please, contact, i think it might be the mobo even though power if going through, cpu fan and what not still starts, but it could be the amd64 though i'm not sure if it would kick in so early, i figured a bad cpu would make the system hang a little later. I am wondering if i could have short circuted something.
thanks

Is it a new board, or did it occur after changing the vid.card.
Ur info is a bit scarse, plz supply us with more info.

K8T Neo Series JUSB connecting

Hello,
While cleaning op my case, and hiding all cabled to optimize my airflow I accidentally ripped out the connectors of the 2nd JUSB connector on my MSI K8T Neo series Motherboard. I first thougt It was made out of 1 connector, but unfortunatly they were about 10 tiny connectors.
that JUSB connector is for my front-side USB 2.0 connectors.
I know how to reconnect them, but I don't know in which order.
They are all different colors and are labled:
2x 'GND' each in an other color, 2x 'Power' each in an other color, ....
I checked my motherboard's "quick user's guide", about those JUSB connectors, where they gice the correct oreder. My Problem is that the lables in the Manual aren't the same as the labels on the tiny connectors.
Does anyone has the correct order, maybe in color, so that I can reconnect them in a proper way?
Thank you very much,
Hans.

...look here...scroll down one post...

K8T Neo Usb Prob

Similar Messages

Maybe you are looking for