K8T Neo2 crashing and memory issues

I bought myself a new PC in late december and have started experiencing some problems with it
Brief system specs:
MSI K8T Neo2
Athlon64 3200
512Mb Samsung PC3200 DDR400
ATI All in wonder radeon 9800 pro
LG DVD writer
Windows XP SP-1
Antec SLK3700BQE case, which came with what I think is an Antec smartpower SL350 PSU
I had two sticks of memory (both the same type), but one of the sticks failed memtest badly so I sent it back and got a working replacement.  Both sticks would pass lengthy bouts of memtest on their own, but would fail occasionally if I put both in (It didn't seem to matter if it was in a DDR configuration or not, but I didn't test non DDR pairings as much).  I tried turning down the ram speed in the bios, but it didn't seem to help.  Any advice on getting this to work would be great.
A much more serious problem I'm having is crashing - The system will ocassionally shut itself down leaving the monitor without a signal.  Sometimes I can reset the system, others I have to switch off the power before the system will respond at all again.  In the past there was sometimes graphical corruption before the failure, although lately it has just been a black screen.  This happens most frequently when working with games using 3D graphics, although infrequently will happen when web browsing.  The crashing seems to have become more frequent lately, particularly since a local heat wave.  The problem may have become more pronounced when I bought the DVD writer to replace a very old CD-ROM, although its hard to judge because I replaced the bad memory stick at the same time.
According to core center the temperatures seem to run under 50 degrees, but the 12V volatage is listed at only 11.12 to 11.18.  Is my PSU the culprit here, or are these symptoms of a different problem?

Your PSU could well be the cause. Can you post its amps at 3,3v / 5v / 12v here? Antec PSU's usually do not have high efficiency (most likely 60-70%), so if the amps are already low and efficiency is too, my guess would be your PSU. It could seriously damage your board, cpu or vid card by the way...
Try solving the mem problem by raising the Vmem by 0.05v or by raising the latencies some (or both)....

Similar Messages

  • After Effects Issues Scrub/Crash and Memory Issue.

    I am sorry if this is redundant. I have Windows XP (SP3) 3 Gb or Ram and adequite hard drive space. When I run After Effects, it loads fine. Import, fine. Scrub timeline. ERROR: Texture too small, GL error, After Effects Crahses.
    Then when I render, my ram reaches 60% stops rendering.
    I will dl the updates and see if tha fixes it. In the meantime is there anything I should know or any settings I should use to boost performance?
    Thanks,
    Allan H.B. Martin
    [email protected]

    Well, for the first error simply turn off OpenGL. Apparently your graphics card is not up to snuff, has a flakey driver or is mis-configured somehow. The second is too generic. When asking such questions, you must provide more info - footages used, target format, effects used etc.. Also have the renderer log more details with the Extra per Frame Info option as well as watching the render status closely (untwirl the details sections to see the current layers/ comps being processed).
    Mylenium

  • Kingston HyperX 2x 512MB + MSI K8T Neo2 + 3200 Winchester = SERIOUS ISSUE

    OK, so thats the spec:
    Microstar K8T Neo2
    Kingston HyperX DDR 2x 512MB PC-400 (KHX3200ULK2/1G) CL2 (producer's timings : 2-2-2-5-1)
    AMD 64 3200 Winchester core CPU
    And here's the problem, watch out - its gonna get real wierd from now on :D
    First setup: Green Slot 1 + Purpule Slot 1 = system dead
    Second: Green 2 + Purp 2 = system dead
    Third: Green 2, only one dice installed and heres what happend: It booted (wow!) but.. the system recognizes it as a 256 dice !! I've triple chcecked, its a double sided 512 module! When I insert both modules into green1 and green2 the system sees only 512 megs while it obvioulsly should see 1 GB !
    I have totally NO IDEA whats going one. The memory modules had been chcecked on a dual channel Nforce2 with a Barton CPU and it works perfectly at peak timings with the proper memory ammount.
    I ask You, what the hell is going on ?

    Interestingly enough I have exactly the opposit issue.
    With BIOS 3.0 my system detected all the memory.  
    I updated to 3.2 and now it only detects 1/2 my memory.  I tried all the slot swaping same issue.
    I've downgraded to BIOS 3.0 and my system randomly shuts off.
    K8T Neo2
    AMD 64 3000+ Winchster
    SimpleTech Dual Channel PC3200 2x512mb DDR400 DoubleSided

  • Flash player crashes and other issues.

    My wife is having issues with Zynga Bingo and Flashplayer.  Over the past 3 days (starting approx 20 July) she will be able to play for a bit and then it will just lock up on her.  Now it won't run at all, Flashplayer keeps giving an error stating it is unresponsive.
    What is odd is that it is only occuring on her account.  When I get on my account or our daughter gets on her account on the same laptop we do not have any of these problems.
    In researching this issue I have seen so many suggestions for fixing it, I have tried to run it on Google Chrome, Internet Explorer and Firefox.  It does the same thing on all browsers, and the other 2 accounts do not have any issues on any of the browsers.
    I have uninstalled and reinstalled the graphics drivers, sound drivers, Flashplayer and Java.
    Why?  If this is a hardware or software issue, is the problem only occurring on one account out of the three when they are all three played on the same laptop.
    After starting the game on her account it comes to the screen where you select how many Bingo cards you want to play and the music and screen freezes a couple seconds after loading and you can't select anything on the screen.
    I should add, we have had many problems with her Zynga account in the past, she had a stroke last year and there was several hundred dollars worth of charges at a time when she was in the hospital and didn't have the laptop with her.  Just a couple months ago her laptop and my laptop both crashed and had to have the operating systems reinstalled (recovery programs failed to work).  This was just after a major windows update, both laptops would not boot up after installing the same updates.  During the week the laptops were being worked on we did not have access to a computer and yet there were "again" hundreds of dollars in Zynga charges which we could not explain.
    Is it possible that her account has somehow been hacked by someone thru the Zynga service, as that is the only place she is having problems...and would explain why only her account locks up and not the other two?
    Attaching a DirectX file so you can see the system setup....what else can I add to help in troubleshooting?  No antivirus programs or spyware has been detected and the operating system is a fresh install.  All she uses the laptop for is her facebook games and email.
    Thankyou for your help.
    System Information
    Time of this report: 7/23/2012, 19:59:46
           Machine name: DEX-PC
       Operating System: Windows 7 Home Premium 64-bit (6.1, Build 7601) Service Pack 1 (7601.win7sp1_gdr.120503-2030)
               Language: English (Regional Setting: English)
    System Manufacturer: Dell Inc.        
           System Model: Dell System XPS L702X
                   BIOS: Default System BIOS
              Processor: Intel(R) Core(TM) i7-2670QM CPU @ 2.20GHz (8 CPUs), ~2.2GHz
                 Memory: 8192MB RAM
    Available OS Memory: 8086MB RAM
              Page File: 2096MB used, 14073MB available
            Windows Dir: C:\Windows
        DirectX Version: DirectX 11
    DX Setup Parameters: Not found
       User DPI Setting: Using System DPI
    System DPI Setting: 120 DPI (125 percent)
        DWM DPI Scaling: Disabled
         DxDiag Version: 6.01.7601.17514 64bit Unicode
    DxDiag Notes
          Display Tab 1: No problems found.
            Sound Tab 1: No problems found.
              Input Tab: No problems found.
    DirectX Debug Levels
    Direct3D:    0/4 (retail)
    DirectDraw:  0/4 (retail)
    DirectInput: 0/5 (retail)
    DirectMusic: 0/5 (retail)
    DirectPlay:  0/9 (retail)
    DirectSound: 0/5 (retail)
    DirectShow:  0/6 (retail)
    Display Devices
              Card name: Intel(R) HD Graphics Family
           Manufacturer: Intel Corporation
              Chip type: Intel(R) HD Graphics Family
               DAC type: Internal
             Device Key: Enum\PCI\VEN_8086&DEV_0116&SUBSYS_04B81028&REV_09
         Display Memory: 1696 MB
       Dedicated Memory: 64 MB
          Shared Memory: 1632 MB
           Current Mode: 1920 x 1080 (32 bit) (60Hz)
           Monitor Name: Generic PnP Monitor
          Monitor Model: unknown
             Monitor Id: CMO1720
            Native Mode: 1920 x 1080(p) (60.010Hz)
            Output Type: Internal
            Driver Name: igdumd64.dll,igd10umd64.dll,igd10umd64.dll,igdumdx32,igd10umd32,igd10umd32
    Driver File Version: 8.15.0010.2455 (English)
         Driver Version: 8.15.10.2455
            DDI Version: 10.1
           Driver Model: WDDM 1.1
      Driver Attributes: Final Retail
       Driver Date/Size: 7/20/2011 08:39:56, 8310272 bytes
            WHQL Logo'd: Yes
        WHQL Date Stamp:
      Device Identifier: {D7B78E66-4256-11CF-3669-B424B7C2C535}
              Vendor ID: 0x8086
              Device ID: 0x0116
              SubSys ID: 0x04B81028
            Revision ID: 0x0009
    Driver Strong Name: oem79.inf:IntelGfx.NTamd64.6.0:iSNBM0:8.15.10.2455:pci\ven_8086&dev_0116&subsys_04b81028
         Rank Of Driver: 00E60001
            Video Accel: ModeMPEG2_A ModeMPEG2_C ModeWMV9_C ModeVC1_C
       Deinterlace Caps: {BF752EF6-8CC4-457A-BE1B-08BD1CAEEE9F}: Format(In/Out)=(YUY2,YUY2) Frames(Prev/Fwd/Back)=(0,0,1) Caps=VideoProcess_YUV2RGB VideoProcess_StretchX VideoProcess_StretchY VideoProcess_AlphaBlend DeinterlaceTech_EdgeFiltering
                         {335AA36E-7884-43A4-9C91-7F87FAF3E37E}: Format(In/Out)=(YUY2,YUY2) Frames(Prev/Fwd/Back)=(0,0,0) Caps=VideoProcess_YUV2RGB VideoProcess_StretchX VideoProcess_StretchY VideoProcess_AlphaBlend DeinterlaceTech_BOBVerticalStretch
                         {5A54A0C9-C7EC-4BD9-8EDE-F3C75DC4393B}: Format(In/Out)=(YUY2,YUY2) Frames(Prev/Fwd/Back)=(0,0,0) Caps=VideoProcess_YUV2RGB VideoProcess_StretchX VideoProcess_StretchY VideoProcess_AlphaBlend
                         {BF752EF6-8CC4-457A-BE1B-08BD1CAEEE9F}: Format(In/Out)=(UYVY,YUY2) Frames(Prev/Fwd/Back)=(0,0,1) Caps=VideoProcess_YUV2RGB VideoProcess_StretchX VideoProcess_StretchY VideoProcess_AlphaBlend DeinterlaceTech_EdgeFiltering
                         {335AA36E-7884-43A4-9C91-7F87FAF3E37E}: Format(In/Out)=(UYVY,YUY2) Frames(Prev/Fwd/Back)=(0,0,0) Caps=VideoProcess_YUV2RGB VideoProcess_StretchX VideoProcess_StretchY VideoProcess_AlphaBlend DeinterlaceTech_BOBVerticalStretch
                         {5A54A0C9-C7EC-4BD9-8EDE-F3C75DC4393B}: Format(In/Out)=(UYVY,YUY2) Frames(Prev/Fwd/Back)=(0,0,0) Caps=VideoProcess_YUV2RGB VideoProcess_StretchX VideoProcess_StretchY VideoProcess_AlphaBlend
                         {BF752EF6-8CC4-457A-BE1B-08BD1CAEEE9F}: Format(In/Out)=(YV12,YUY2) Frames(Prev/Fwd/Back)=(0,0,1) Caps=VideoProcess_YUV2RGB VideoProcess_StretchX VideoProcess_StretchY VideoProcess_AlphaBlend DeinterlaceTech_EdgeFiltering
                         {335AA36E-7884-43A4-9C91-7F87FAF3E37E}: Format(In/Out)=(YV12,YUY2) Frames(Prev/Fwd/Back)=(0,0,0) Caps=VideoProcess_YUV2RGB VideoProcess_StretchX VideoProcess_StretchY VideoProcess_AlphaBlend DeinterlaceTech_BOBVerticalStretch
                         {5A54A0C9-C7EC-4BD9-8EDE-F3C75DC4393B}: Format(In/Out)=(YV12,YUY2) Frames(Prev/Fwd/Back)=(0,0,0) Caps=VideoProcess_YUV2RGB VideoProcess_StretchX VideoProcess_StretchY VideoProcess_AlphaBlend
                         {BF752EF6-8CC4-457A-BE1B-08BD1CAEEE9F}: Format(In/Out)=(NV12,YUY2) Frames(Prev/Fwd/Back)=(0,0,1) Caps=VideoProcess_YUV2RGB VideoProcess_StretchX VideoProcess_StretchY VideoProcess_AlphaBlend DeinterlaceTech_EdgeFiltering
                         {335AA36E-7884-43A4-9C91-7F87FAF3E37E}: Format(In/Out)=(NV12,YUY2) Frames(Prev/Fwd/Back)=(0,0,0) Caps=VideoProcess_YUV2RGB VideoProcess_StretchX VideoProcess_StretchY VideoProcess_AlphaBlend DeinterlaceTech_BOBVerticalStretch
                         {5A54A0C9-C7EC-4BD9-8EDE-F3C75DC4393B}: Format(In/Out)=(NV12,YUY2) Frames(Prev/Fwd/Back)=(0,0,0) Caps=VideoProcess_YUV2RGB VideoProcess_StretchX VideoProcess_StretchY VideoProcess_AlphaBlend
                         {BF752EF6-8CC4-457A-BE1B-08BD1CAEEE9F}: Format(In/Out)=(IMC1,YUY2) Frames(Prev/Fwd/Back)=(0,0,1) Caps=VideoProcess_YUV2RGB VideoProcess_StretchX VideoProcess_StretchY VideoProcess_AlphaBlend DeinterlaceTech_EdgeFiltering
                         {335AA36E-7884-43A4-9C91-7F87FAF3E37E}: Format(In/Out)=(IMC1,YUY2) Frames(Prev/Fwd/Back)=(0,0,0) Caps=VideoProcess_YUV2RGB VideoProcess_StretchX VideoProcess_StretchY VideoProcess_AlphaBlend DeinterlaceTech_BOBVerticalStretch
                         {5A54A0C9-C7EC-4BD9-8EDE-F3C75DC4393B}: Format(In/Out)=(IMC1,YUY2) Frames(Prev/Fwd/Back)=(0,0,0) Caps=VideoProcess_YUV2RGB VideoProcess_StretchX VideoProcess_StretchY VideoProcess_AlphaBlend
                         {BF752EF6-8CC4-457A-BE1B-08BD1CAEEE9F}: Format(In/Out)=(IMC2,YUY2) Frames(Prev/Fwd/Back)=(0,0,1) Caps=VideoProcess_YUV2RGB VideoProcess_StretchX VideoProcess_StretchY VideoProcess_AlphaBlend DeinterlaceTech_EdgeFiltering
                         {335AA36E-7884-43A4-9C91-7F87FAF3E37E}: Format(In/Out)=(IMC2,YUY2) Frames(Prev/Fwd/Back)=(0,0,0) Caps=VideoProcess_YUV2RGB VideoProcess_StretchX VideoProcess_StretchY VideoProcess_AlphaBlend DeinterlaceTech_BOBVerticalStretch
                         {5A54A0C9-C7EC-4BD9-8EDE-F3C75DC4393B}: Format(In/Out)=(IMC2,YUY2) Frames(Prev/Fwd/Back)=(0,0,0) Caps=VideoProcess_YUV2RGB VideoProcess_StretchX VideoProcess_StretchY VideoProcess_AlphaBlend
                         {BF752EF6-8CC4-457A-BE1B-08BD1CAEEE9F}: Format(In/Out)=(IMC3,YUY2) Frames(Prev/Fwd/Back)=(0,0,1) Caps=VideoProcess_YUV2RGB VideoProcess_StretchX VideoProcess_StretchY VideoProcess_AlphaBlend DeinterlaceTech_EdgeFiltering
                         {335AA36E-7884-43A4-9C91-7F87FAF3E37E}: Format(In/Out)=(IMC3,YUY2) Frames(Prev/Fwd/Back)=(0,0,0) Caps=VideoProcess_YUV2RGB VideoProcess_StretchX VideoProcess_StretchY VideoProcess_AlphaBlend DeinterlaceTech_BOBVerticalStretch
                         {5A54A0C9-C7EC-4BD9-8EDE-F3C75DC4393B}: Format(In/Out)=(IMC3,YUY2) Frames(Prev/Fwd/Back)=(0,0,0) Caps=VideoProcess_YUV2RGB VideoProcess_StretchX VideoProcess_StretchY VideoProcess_AlphaBlend
                         {BF752EF6-8CC4-457A-BE1B-08BD1CAEEE9F}: Format(In/Out)=(IMC4,YUY2) Frames(Prev/Fwd/Back)=(0,0,1) Caps=VideoProcess_YUV2RGB VideoProcess_StretchX VideoProcess_StretchY VideoProcess_AlphaBlend DeinterlaceTech_EdgeFiltering
                         {335AA36E-7884-43A4-9C91-7F87FAF3E37E}: Format(In/Out)=(IMC4,YUY2) Frames(Prev/Fwd/Back)=(0,0,0) Caps=VideoProcess_YUV2RGB VideoProcess_StretchX VideoProcess_StretchY VideoProcess_AlphaBlend DeinterlaceTech_BOBVerticalStretch
                         {5A54A0C9-C7EC-4BD9-8EDE-F3C75DC4393B}: Format(In/Out)=(IMC4,YUY2) Frames(Prev/Fwd/Back)=(0,0,0) Caps=VideoProcess_YUV2RGB VideoProcess_StretchX VideoProcess_StretchY VideoProcess_AlphaBlend
           D3D9 Overlay: Supported
                DXVA-HD: Supported
           DDraw Status: Enabled
             D3D Status: Enabled
             AGP Status: Enabled
    Sound Devices
                Description: Speakers (Realtek High Definition Audio)
    Default Sound Playback: Yes
    Default Voice Playback: Yes
                Hardware ID: HDAUDIO\FUNC_01&VEN_10EC&DEV_0665&SUBSYS_102804B8&REV_1000
            Manufacturer ID: 1
                 Product ID: 100
                       Type: WDM
                Driver Name: RTKVHD64.sys
             Driver Version: 6.00.0001.6312 (English)
          Driver Attributes: Final Retail

    Thank you for providing all details in your first post; very few posters do that.
    Two things to try:
    disable hardware acceleration on the affected account; see http://forums.adobe.com/thread/891337
    if that improves the situation, then updating the graphics drivers would be advised; see http://forums.adobe.com/thread/945765 - you can re-enable hardware acceleration after that

  • IPad 1 and memory issues

    I mean this thing is slooowwww. Many apps crash back to the home screen. I have an app called System and it is showing Wired: 59MB at 36.56% What is this? Apps that are automatically on my iPad? Active shows 2MB at 13.90% and I have nothing running except this app. The reason I am bringing all this up is I was wondering is there any way to speed this iPad up? I mean the memory is atrocious! This thing is slow. And it is a brand new one that I got from the Apple store. Granted, it is not an iPad 2, as I do not have unlimited wealth, as Apple assumes we all do, it is the iPad 1. Maybe the memory issue is having too many apps downloaded? I have absolutely nothing running in the background as I close every app I open because the iPad is so slow and crashes even default email back to the home screen at times! I just want to make this thing faster like the day I first got it. Right now, it is serving as a paper weight as I can't keep anything running for very long. Things run smoothly, yes, but many things do not. Still wondering what this Wired section is, as it is taking up so much of my memory. I have only 88MB free and as soon as I open any app, that diminishes rather quickly.

    No it's not jailbroken. I will never do that to any of my devices. I am talking about memory. I have plenty of storage. Just tired of apps crashing back to the home screen.

  • K8T-Neo2 ver1 and WD GB 1TB Drive

    All, maybe this needs to go in the retirement folder for motherboards, but here is my problem, if someone could help me.
    I have a K8T-Neo2 ver1 (MS-6702e) with 2GB of RAM and AMD 3000+ Athlon 64 processor.
    I'm using the Promise SATA controller for a RAID1 mirror for my OS (two 80GB drives).  I also have a 3ware 9500S series RAID5 controller with four 320GB drives in the machine.
    I'm trying to install a Western Digital GB 1TB (3Gb/s) drive on the VIA VT8237 chip.  I've read on Wikipedia there is a bug with the VIA VT8237 and you have to manually step the drive down to 1.5Gb/s, which I have by using jumpers 5 and 6. 
    I've double checked that I have both SATA controllers enabled, and also flashed my BIOS up to 3.3 (1/10/2005).  I did flash up to version 9, but it had issues with my 3ware controller for some reason, so I backed it down to the version 3 train.
    As of right now, my motherboard does not see the 1TB drive, even after I've stepped it down to 1.5Gb/s.  Not sure what to do next.  I've been trying to search the net for answers, and have come up short so far.  Any info or insight would be appreciated.

    "Boys and Girls, when trying to install a SATA drive, always remember to load your Windows drivers."
    that depend of sata controller.. and how is configured as RAID or not.
    I've read on Wikipedia there is a bug with the VIA VT8237 and you have to manually step the drive down to 1.5Gb/s, which I have by using jumpers 5 and 6.
    That is not a bug... simple onboard ctrl do not support SATA2, and due this the Sata drive must be limited 1st to sata1.

  • Firefox 3.6.8 and memory issues

    After the last update to 3.6.6, I disabled plugin-container per the instructions given on the forum, and my RAM problems went away. However, after the automatic update to 3.6.8, the memory problems came back, with memory usage going up to 92%. I downgraded to 3.6.4, and turned plugin-container off again; while memory usage is currently at 84%, it is not as low as it was before the upgrade to 3.6.8. (79-80%) (There is very little difference in the websites being opened on the various tabs.)
    == This happened ==
    Every time Firefox opened
    == I upgraded to 3.6.8

    ffs guys. It's a free browser. It's cool. We love it. But can we do something about memory issues? Almost every release has huge memory leaks.
    How about halving the release points and focus on memory issues for the other half of the time. I am a long time user since way back in the day and it seems to me that instead of trying to release so many versions, we should be focused more fixing the current release.
    I say put a moratorium on new features until bloat can be fixed. These experiences are starting to give me a hardon for IE again.
    Screw new features. I can deal with plain old tabs like they are. I don't need more bells and whistles. This browser has been kicking ass and taking names for a loonnnggggg time. We don't need more bloat. Keep the security fixes coming but everything else can wait. Take a breath. Stop and smell the roses for a few weeks.

  • GPMC Crashing and Display issues.

    Today I went to open the GPMC on my Windows 8 Desktop and after going to edit a policy we have created all the menu items were blank. I could see the icons for them, but they had no name. After trying to navigate for a few moments MMC Crashes and gives me
    this error in event viewer:
    Faulting application name: mmc.exe, version: 6.2.9200.16384, time stamp: 0x5010a074
    Faulting module name: ntdll.dll, version: 6.2.9200.16420, time stamp: 0x505aaa82
    Exception code: 0xc0150010
    Fault offset: 0x0007df5e
    Faulting process id: 0xfc8
    Faulting application start time: 0x01cdb7783eb3c748
    Faulting application path: C:\WINDOWS\SysWOW64\mmc.exe
    Faulting module path: C:\WINDOWS\SYSTEM32\ntdll.dll
    Report Id: 8bacb439-236b-11e2-be6b-984be1ebad9b
    Faulting package full name:
    Faulting package-relative application ID:
    with this information afterwords:
    Fault bucket -1088739078, type 1
    Event Name: APPCRASH
    Response: Not available
    Cab Id: 0
    Problem signature:
    P1: mmc.exe
    P2: 6.2.9200.16384
    P3: 5010a074
    P4: ntdll.dll
    P5: 6.2.9200.16420
    P6: 505aaa82
    P7: c0150010
    P8: 0007df5e
    P9:
    P10:
    Attached files:
    C:\Users\pomeroyt\AppData\Local\Temp\WER66CC.tmp.WERInternalMetadata.xml
    C:\Users\pomeroyt\AppData\Local\Temp\WER6C3B.tmp.appcompat.txt
    These files may be available here:
    C:\ProgramData\Microsoft\Windows\WER\ReportArchive\AppCrash_mmc.exe_636e6b2f6e27a9c7f7e820f7a0adb57213626294_05c36ce6
    Analysis symbol:
    Rechecking for solution: 0
    Report Id: 8bacb439-236b-11e2-be6b-984be1ebad9b
    Report Status: 1
    Hashed bucket: 098ebb650f3c851a055c696107776b03
    I'm not really sure where to go from here. Has anyone else had this issue? 
    Were running a 2008 domain. 

    I'm also having this problem. Error text from my system below.  It's a fresh install of Windows 8, joined to our domain and updated. VMWare Tools was installed automaticaly, but not even antivirus aside from that. It seems I can use most of the
    features of the console, I've even succesfully modified a GPO. If I select the comain in the left pane though, guarenteed crash.  I've tried rebooting.
    Anyone make any progress?
    Problem signature:
    Problem Event Name:                       
    APPCRASH
    Application Name:                            
    mmc.exe
    Application Version:                          
    6.2.9200.16496
    Application Timestamp:                    
    50ece2e8
    Fault Module Name:                         
    gpmgmt.dll
    Fault Module Version:                       
    6.2.9200.16518
    Fault Module Timestamp:                 
    510ca9a6
    Exception Code:                                 
    c0000005
    Exception Offset:                               
    0000000000154f4b
    OS Version:                                         
    6.2.9200.2.0.0.256.4
    Locale ID:                                            
    1033
    Additional Information 1:                 
    f5d5
    Additional Information 2:                 
    f5d5f2edea5447000260123656b930b4
    Additional Information 3:                 
    f883
    Additional Information 4:  f883ee6437fb5cbaf147d7c9ea29db21

  • Bridge CS5 suddenly crashing with memory issues

    Over and over again, several times a work session, Bridge quits, saying that it has insufficient memory. I have WIndows XP, 4 gigs of ram. Can you point me in the right direction to troubleshoot this problem? DId I change the wrong settings perhaps? Could it have happened when I had to delete my Photoshop prferences? All help will be much appreciated as it's driving me bats~

    Memory issues do not necessarily mean RAM.  It can also mean
    insufficient disk space.
    If you do not have at least 20% of free space on your HD you need to eliminate files or get a larger dirve.   Also, you may have free space but you need a large block of contiguous space.  So delete temp files, and extraneous programs then defrag the HD.
    Hope this helps.

  • I have a battery and Memory issue - late macbook pro 2011

    Macbook Pro 13" Late 2011 Model
    Battery Issue
    After upgrading to Lion, my batter life is 3 hours after full charge. It was 7-8 hours in leopard.
    Hoping this is a common issue and someone has a quick solution.
    Memory Issue
    I had 4GB Ram and found it would run to virtually nothing and not free any inactive RAM. I though the solution to this was to buy more RAM, which I did.
    I now have 8GB RAM and it agains runs to virtually nothing on non labour intensive software like safari or mail. It doesnt free up any RAM when it reaches a certain point. Instead it freezes and I'm forced to restart the computer. I use Final Cut Pro X and Photoshop/Illustrator fairly regualry. I'm assuming the RAM is is used with those but even when these are closed the RAM is low.
    Any ideas?
    Cheers

    You should take your Mac to an official apple retail store, as it is not common to have these problems regarding battery and memory.

  • New 3.46 k8t neo2 BIOS and agp lock

    does the agp lock work now?
    or with the 9betas. is it working?
    on k8t neo2
    thanks. i have 3.30 and it'S not working on my board :(

    Quote from: Toaster56 on 24-June-05, 05:01:41
    well i guess the lock is working. i might just have a bad cpu.
    http://img68.echo.cx/img68/7518/agpfre8pe.jpg
    'Bad' would be a subjective statement in this case. If you do have an early batch Winchester, it overclocks less than the later batches. But it still gives you a lot more than you paid for.
    P.S.
    Following your link, I noticed your Vcore is a bit low at 200 MHz. When overclocking, you should raise it some to get above 225 MHz and be stable. At 230, something like 1.49v should do the trick. Also, what kind of power supply do you use?
     

  • ITunes 10.7.0.21 crashing and memory usage

    Running on Windows 7 64 bit.  This is the first version I have had this issue with.  After running for several minutes, iTunes will do one of three things:
    Crash
    Freeze, and require me to force it closed in the task manager
    Display a recurring message about not enough memory
    Watching it more closely, iTunes seems to continue to take up more and more memory the longer it is running, which I suspect is the cause of all three symptoms.
    Anyone else experiencing this memory leak problem?
    Is this just a problem with this version that I'll have to wait until the next one, or is there a fix?

    I am having the very same issues, admittedly with and older (5 yrs) Windows Vista 32-bit Dell laptop. I had been holding out for a little while on allowing iTunes to upgrade on my computer, and had no issues or complaints with iTunes 7, 8, or 9. But after I allowed it to upgrade today, 10.7 is worthless.
    After a few minutes, iTunes pops up with a message regarding insufficient memory, freezes, then crashes. Not even using video, just putting together a playlist of regular file size songs.
    I know after reading a bit on the boards that trying to re-install version 9 may cause some things to be lost in translation from 10 to 9, apparently because of some changes in the way the software is set up. Please correct me if that is not the case.
    However, I would rather risk it (I have all of my music files on an external hard drive) than to keep having iTunes behave as it is- making the software that I've been using for years worthless to me since it cannot work correctly.
    By the by, I know my laptop is ancient by technology standards, but won't be upgrading quite yet.
    If you know a reliable source to download the previous versions of iTunes for Windows, I'd be grateful if you could point me in the right direction. I'm fairly computer savvy, and know that I'll need to un-install the most recent iTunes version prior to installing an older version.

  • IMessage and Memory issues since updating iPhone to ios 8.1.3

    I stupidly updated my iPhone 5S due to the idea of a wider variety of emojis and now everything has gone wrong. My iMessage keep disappearing and reappearing or not coming through at all on my phone but they're all still coming through perfectly fine on my Macbook. As well as the iMessage issue my iPhone keeps on insisting me memory is full even though I've deleted pretty much everything, nothing loads my screen just crashes then goes back to homepage...my patience is running low and by the looks of Twitter I'm not the only one facing these issue my only wonder now is what, if anything can I do?

    Greetings Nezza80,
    After reading your post, it sounds like you are experiencing an error when viewing videos. You may want to consider restarting the device first, and then resetting if that does not work. This article provides detailed instructions for Restarting, and Reseting:
    Restart or reset your iPhone, iPad, or iPod touch - Apple Support
    How to restart
    Press and hold the Sleep/Wake button until the red slider appears.
    Drag the slider to turn your device completely off.
    After the device turns off, press and hold the Sleep/Wake button again until you see the Apple logo.
    How to reset
    You should reset your device as a last resort and only if you can't restart it.
    To reset, press and hold both the Sleep/Wake and Home buttons for at least 10 seconds, until you see the Apple logo.
    Thank you for contributing to Apple Support Communities.
    Best,
    Bobby_D

  • Neo2 Platinum: 4gb Memory issues

    Hi,
    I have just installed 2 sets of Corsair TWINX2048-3200C2PT (pair of 1024 MByte DDR SDRAM). This means in total I have 4 x 1gb modules. These are currently running at 2-3-3-6. However the system is only picking up 3gb. I understand the motherboard wont pick up full 4gb but losing a whole gig is madness. I also understand about the single and double sided ram thing aswell. Is there anything to resolve this issue?
    Motherboad: MSI K8N Neo2 Platinum
    Graphics: Gainward Bliss 7800gs+ 512MB
    Sound Card: Creative Audigy 2 ZS
    Coolermaster 650W Powersupply
    2 X TWINX2048-3200C2PT (4gb RAM)
    Chaz

    Quote from: BOSSKILLER on 20-February-07, 20:21:30
    Cell Menu, DRAM Configuration, H/W memory hole Remapping & S/W memory hole Remapping available there.
    i done this for both H/W memory and S/W memory. It seems that it is now picking up 4gb in the bios but only 3gb in windows.
    CHAZ

  • Pre9 Crashes and Memory

    Hello,
    I am 90% done with a video that is about 20 minutes long. It contains video and photo images. I cannot complete the project because PrE keeps crashing I believe due to memory. My machine is XP with 4GB RAM.
    I took the steps recommended. All my photos have been reduced to 1000X750, then placed in a slideshow (from Organizer). I reset my virtual memory to settings 4GB and 8GB (max). I was a bit confused because I set both my C and D HDD's on these settings and I'm not sure which Windows is actually using for virtual memory.
    I can only work about a minute before the system seems to overload then crashes. I'm in a bit of trouble with this and would appreciate any help. Thank you! Stan

    Stan,
    At about 70% of capacity, a HDD begins to slow down, and its performance deteriorates, the closer to 100% one comes.
    Now, if you only have one physical HDD, C:\, and add an additional HDD, D:\, I would create a folder for each of your Projects. Then, I would Move my Assets from C:\. Here, one has several choices, which I will get into in a bit. I would Move my PREL files to their respective Project folders. The Scratch Disks, with the Media Cache, Render Files, etc., can be Moved, or probably better, can be Deleted, as PrE will regenerate those - the CFA's and PEK's, when you Open the Project (be patient, until that work is done, and just watch the little "progress bar" in the lower-right of the GUI. In Edit>Preferences, set Scratch Disk to "Same as Project," which will now be on your D:\. When needed, you can hit Enter, to Render the parts of your Timeline, that will need it. I would not bother Moving those Render Files, as it might not work to reestablish the links to them, and it will only take a few moments to Render again.
    Now, once you have done the Move, when you Open one of the PREL files, the links to the Assets will NOT be valid. Those links are absolute Paths, and you will have changed the drive letter, so they will be broken. PrE will ask you, "Where is file _____ ?" and present you with navigation screens, and also a Finder. Just navigate to the new folder on D:\, where the first missing Asset is, and PrE will link to it, then survey that folder, and re-link all Assets used in that Project. If you have sub-folder with the Assets, you will need to repeat for each sub-folder, but only for the first un-linked file in each. For more detail, see this ARTICLE.
    For setting up Project folders, and sub-folders, this ARTICLE gives you my scheme. It is not the only way to do it, so feel free to adapt from it, to suit the way that you like to work. If you notice, I have my media files stored elsewhere, and only use Copies of them in the sub-folders. The location of your media files is a personal choice. Some keep them in sub-folders by subject, or maybe date, and just link to the ones Imported, from there. I like to keep mine separate, and just Copy them to, say the Video sub-folder below my Project's root folder. This is your choice.
    Also, and before you do anything with that new D:\, there is another possible workflow - the Project Archiver. It will create a Copy of your Project, on the Destination Disk that you choose - D:\ in this case. It will gather up the Assets, and Copy them too, but depending on the folder structure, where those Assets resided, at Import, there can be some "missing files." If you use Project Archiver, make sure to test the Project, that it Copied over to D:\, to make sure that it was able to get everything, and that there are no problems with this Copy of your Project.
    I would give this some thought, before you do anything. Plan how you'd like to handle it, before you Move, Copy or Delete the very first file. Also, and since you are starting with at least a half-way "clean slate," this gives you the opportunity to decide on the folder structure, that works best for you.
    In the end, cleaning your Projects, your Media and your Scratch Disks off of C:\, and locating them onto D:\, will likely speed things up.
    In an ideal world, one would have a C:\, with ONLY the OS, programs and possibly the Page File, or part of it. Then, they would have their Media on a separate, physical HDD. Last, they would have their Projects, and their Scratch Disks on yet a third physical HDD. If one only has 2 physical HDD's, then they would combine the latter two, onto one physical HDD.
    In my folder/sub-folder scheme, above, I sacrifice some performance, by not splitting my Media and my Projects/Scratch Disks over separate HDD's, but I use the portability of my FW-800 externals, between machines, and then have a "one-touch" Delete (the Project's root folder), when I have finished. Were I not using the portability, I would split the Media to one HDD, and Projects/Scratch Disks to another. As the originals of my Media are on my NAS, what I would have on that second HDD would just be Copies, and I would use the same Project folder, as on the other HDD, for each Project. Then, I would know which Project was included, and would then have a "two-touch" Deletion - one for the Project and everything under it, and one for that Project's Media Copies.
    Good luck,
    Hunt

Maybe you are looking for