K9A2 CF-F V2 won't run 1066mhz ocz ram please help

Question

Ok I have searched this board for anyone having this trouble and cant seem to find it.  Now I am thinking I bought the wrong board, so here is my problem.   K9A2 CF-F V2 MB w/ Phenom Tri-core processor with 2 sticks of 1GB of OCZ 1066 ram = 2gb total on in each slot 3 and 4 but the slots are different colors but according to most that shouldnt make a difference,  I have changed every setting in the bios that I can see but the fastest I can get the ram to run is 800mhz.  some one please help.  I saw where someone says to change the volt setting in bios for the mem. but I cant find where to change that, also saw something about 5-5-5-18 t2 so I did that but what about the rest of the settings they leave at auto but still no avail then I saw another post say to set them at 5-6-6-18 T2 still nothing wont boot with either of these configs, what in the heck am I doing wrong starting to think that the MB wont run OCZ mem.  maybe different mem would work what you think?  like I said 667 and 800 will work but 667 seems more stable. ok thats it for now by the way 580 watt power supply .

Answer 1

ok here is what it says
Cell menu:
current cpu clock = 2100mhz (no option to change here)
current ddr mem freq. = 800 mhz
D.O.T Control = Disabled (current) or private 1% up to Commander 15%
AMD cool and quiet = disabled (current) or enabled
HT Ratio = Auto or 1x upto 13x
Adjust cpu FSB frequency = 200mhz or up to 600mhz max
Adjust Cpu Ratio = 10.5x or downto 4x
ADVANCE DRAM CONFIGURATION = PRESS ENTER
after pressing enter here is what I have set
Dram timing mode = Both (current) or Auto or dct0 or dct 1 or back to both
Cas latency(cL) = Auto (current) or 3clk upto 7clk DH only
TRCD = Auto (current) or 3clk upto 6clk or back to auto
TRP = Auto (current) or 3clk upto 6clk or back to auto
TRTP = Auto (current) or 2clk - 4clk or 3clk - 5clk or back to auto
TRAS = Auto (current) or 5clk - 18clk or back to auto
TRC = Auto (current) or 11clk- 26clk or back to auto
TWR = Auto (current) or 3clk - 6clk or back to auto
TRRD = Auto (current) or 2clk - 5clk or back to auto
TWTR = Auto (current) or 1clk - 3clk or back to auto
this is the same for the second row
Bank Interleaving = Auto (current) or disabled
1t/2T memory timming = 2T (current) or 1T
Software memeory hole = Enabled (current) or Disabled
unganged mode support = Enabled (current) or Disabled
Now Back to cell menu
FSB/MEMORY RATIO = 1:2 (current) or 1:1 or 1:1.33 or 1:1.66 or 1:2 or 1:2.66 or auto
ADJUSTED DDR MEMORY = 800MHZ (no options here)
Adjust PcI frequency = 100 (current) or upto 150
Auto Disable Dimm/Pci Freq. = Enabled (current) or disabled
Cpu volts = AUTO (current) or upto ?
Memory Volts = 2.1 (current) or upto 2.9 or down to 1.8 default
NB Volts = Auto or upto 1.10 - 1.40
Hypertransport = Auto (current) 1.20 - 1.50v
Spread spectrum = Disabled (current) or Enabled
that is it any tips on what to change here please do tell the 800mhz setting is very stable, memory is in channels 1 and 2 closest to the cpu, ran memtest 2 passes all good no errors not sure what else to do hmmm, thanks ahead of time