K9N Neo V3 : PCI-E and PCI-E x1/PCI VGA cards at the same time ?

Hello,
I'm thinking about getting one more VGA card to resolve my dual screen issue :
Quote
I use two monitors. PC monitor as first screen, TV is extended for watching videos.
PC : Philips 220aw (22", 1680x1050 @ 60Hz) DVI-DVI
TV : LG 42lh3000 (42", 1920x1080 @ 24Hz) DVI-HDMI
I've been trying to get smooth playback on the TV for days, but random stutter happens.
When a video (mostly HD contents) is played on the TV while using the PC monitor, things like minimize/maximize windows, page scrolls stutter and so does the video. Idle while watching videos also stutters randomly.
I tried almost every combinations of renderers/codecs/players, tried by desactivating aero and all the fancy graphics, but it didn't solve the problem.
The only way i get smooth playback on the TV, is by desactivating the PC monitor. (Using nVidia panel or "Win" key+P), so only the TV is active.
I tried with a Blu-Ray using DXVA and it was smooth.
I haven't got a chance to test with a better graphic card yet. This issue doesnt happen on XP though.
Here are the specs :
K9N Neo V3
Athlon 64 x2 @ 3Ghz
4Go DDR2-800
8800 GT 512Mo (driver 197.45)
Win7 Ultimate 32 Bits.
Corsair 450W 80+
My question is : Can i add a PCI-E x1 or a PCI VGA card on this motherboard, so each screen will have its own VGA card ?
                      If so, both nVidia or ATI would work ?
Thank you.

It would be one of these, if it is allowed by the K9N Neo V3.
http://www.club3d.nl/products/products_ending_page_7_with_id.cfm?product_id=154
http://www.club3d.nl/products/products_ending_page_7_with_id.cfm?product_id=223
I will try to test with an ATI card if i can find one.

Similar Messages

  • How do I set upmy Imac to allow using both my computer speakers and a Bose SoundLink system as outputs at the same time.  I can use one or the other, but not both.

    how do I set up my Imac to allow using both my computer speakers and a Bose SoundLink system as outputs at the same time.  I can use one or the other, but not both.  From systems Preferences I must select one or the other.  I want both to work all the time.

    Hi,
    I would recommend you to use 0FI_AP_4 rather using both, particularly for many reasons -
    1. DS: 0FI_AP_4  replaces DataSource 0FI_AP_3 and still uses the same extraction structure. For more details refer to the OSS note 410797.
    2. You can run the 0FI_AP_4 independent of any other FI datasources like 0FI_AR_4 and 0FI_GL_4 or even 0FI_GL_14. For more details refer to the OSS note: 551044.
    3. Map the 0FI_AP_4 to DSO: 0FIAP_O03 (or create a Z one as per your requirement).
    4. Load the same to a InfoCube (0FIAP_C03).
    Hope this helps.
    Thanks.
    Nazeer

  • For the past month, I've had an echo of my voice while I'm talking on my phone.  It's very annoying and sounds like multiple people are speaking at the same time and it's only me.  Anyone know what's wrong?

    For the past month, I've had an echo of my voice while I'm talking on my phone.  It's very annoying and sounds like multiple people are speaking at the same time and it's only me.  Anyone know what's wrong?

    For the past month, I've had an echo of my voice while I'm talking on my phone.  It's very annoying and sounds like multiple people are speaking at the same time and it's only me.  Anyone know what's wrong?

  • Slatebook x2 - USB flash and SD card at the same time

    Hello, after almost two years of using this device I had a situation when I wanted to connect USB flash drive and a SD card at the same time (I wanted to copy files from SD to the USB flash drive). I connected the SD card (standard size) to the keyboard module. It was mounted OK. Then I connected the USB flash drive to the keyboard module. This was not mounted at all (no error message). When I dismounted the SD from storage menu then the USB flash drive was mounted automatically. I tried various orders of connecting the devices. I managed to get them work at the same time but then suddenly the USB drive was dismounted. I did not try to perform factory reset (please do not ask this for every issue, I have quite apps, files and settings on the device). It does not matter if the Slatebook is connected to power source. The Slatebook software is fully updated.note: The USB flash drive and the SD card works without any problem when only one of them is connected. Does anyone use SD card and USB flash drive at the same drive? Does it work for you?

    Audio Hijack Pro <http://www.rogueamoeba.com/audiohijackpro/> lets you take the audio output from any application and add multiple effects. Using the "Auxiliary Device Output" effect will send the audio to more than one device.

  • My new Apple TV 2nd generation and computer cannot to my Airport Express at the same time, whats up?

    My Airport Express wont allow both my computer and new Apple TV to be conected at the same time. In Network Preferences I have to manually connect my Apple TV and when I do then it disconnects my computer. When I go to Network Preferences to manually connect my computer it disconnects my Apple TV. Both cannot be connected at the same time. Whats the fix?

    I've tried to set up the IP's manually, still doesn't work. In fact I get a message saying that there is another device trying to use my computers IP address of 00.0.0.0. Thats not my computers IP its my Airport IP. Then neither my computer nor my Apple TV can connect. I change things back to auto configuation its either the Apple TV or the computer which I have to change in Network Preferences. It even tells me that my computer is connected to my network in the status bar and in Network Preferences when it is not. I never had this problem with my old Apple TV (1st).

  • How can I record a guitar and my voice (only voice with mic) at the same time ?, how can I record a guitar and my voice (only voice with mic) at the same time ?

    how can I record a guitar and my voice (only voice with mic) at the same time ? I have one interface with Input 1 mic, Input 2 guitar, everything is working correct, but how can I activate multi recording or something like that... thanks

    Set your inputs on your channel strips and make sure you have one set to input 1 and the other input 2.  Arm the 2 audio tracks(the "R" in the track header. They will turn red and flash), then hit the record button. 

  • Is it possible to listen to music through bluetooth and be on a call with earbuds at the same time?

    Is it possible to listen to music through bluetooth and be on a call with earbuds at the same time?
    I would like to be able to talk on my iPhone with the EarPods while playing music via Bluetooth in my car.  Are there any third party products that will allow this?

    Sorry,  iOS will pause the music playback when you are on the phone call.  You can set iOS to use bluetooth for your audo playback on your music app, and select the earpods for the phone app, but as soon as you answer the phone call, iOS will pause the music playback.  This is a core OS feature, so you will not find any certified iOS app that will do what you want.
    As a side note, please use extra caution when using your ear pods while driving.  It is not safe as you may not hear emergency vehicles, car horns, railroad crossing bells, etc., and it is illegal in many states (in the US).

  • My brother and I will both be in Quito at the same time but staying in different hotels. If we both have facetime how would we call each other (over wifi of course)?

    My brother and I will both be in Quito at the same time but staying in different hotels. If we both have iphones with facetime how would we call each other (over wifi of course)?

    Hello ajs42548,
    The article linked below details how to go about using FaceTime. In order to use FaceTime over Wi-Fi, just verify that you are connected to a Wi-Fi network prior to initiating the call.
    iOS: Using FaceTime
    http://support.apple.com/kb/HT4319
    Cheers,
    Allen

  • How to acquire multi-camera images from one PCI-1409 card at the same time?

    What do I need to do? The hardware or software?
    Can you provide me your solution or 3rd-party ones?

    If you need to aquire images at exactly the same time it will require using two 1409 boards and trigggering the camera simultaneously from the same signal. If you use one board with multiple camera, you will not be able to get images at exactly the same time. This is because there is only one A to D converter on the board which must be shared between channels, so you will have a slight delay of approximately one frame from when the camera is reading one channel to the next. If you trigger the cameras simultaneously, they will both be sending information into the baord, but only one can be read at a time, so the second would not be taken in. Below is a link to approaches for coinnecting multiple cameras:
    http://digital.ni.com/public.nsf/3efedde4322fef19862567740067
    f3cc/ff3c5c368e34a12286256ac6004bd844?OpenDocument
    I hope this helps!
    Chris D

  • Is it possible to be connected with a 3G modem for internet access and a WiFi router for printer sharing at the same time?

    For our only internet access we have a 3G wireless modem. I have since purchased a WiFi printer and router to connect all the comptuters to in the house. The PCs have no problem with using both the 3G connection and the WiFi signal at the same time to print, however, the MacBook Pro will not connect to the 3G network and the router, it will drop the internet access from the modem and attempt to connect via WiFi (which has no internet access). Is there a solution that is available to remedy this? I attempted to create an adhoc printer network, however, the macbooks again will not print off of this, only the PCs. And I'm getting a bit frustrated overall with this.

    The 3G wireless modem is on one of the PC's correct?
    Why don't you pass the Internet through the Ethernet port to the router via Cat5 cable, then have that transmit a Wifi signal that everything else can use, then connect the printer to the router for print sharing?
    You would have to turn off the wifi on the comptuer with the 3G modem as it's physically connected to the router and can't connect to the other machines as they are all connected to the router for sharing.
    The Mac has the ability to pass, Internet Sharing in the System Preferences.
    Do you have software for the Mac to run the 3G modem?

  • Will USB-6008 DAQ be able to power and record voltage for UMS T5 tensiometer at the same time?

    I would like to use my NI USB-6008 to provide power to my UMS T5 tensiometer  (http://www.ums-muc.de/en/products/tensiometer/t5.html) as well as take readings from it, but I don't know if this is possible to do properly. The supply voltage for the instrument can be as low as 5V, which I can easily get from the dedicated +5V channel. I am able to power the instrument and connect it to an analog input on the 6008 and measure a voltage in differential mode. However, while reading the support literature for the instrument, I find the following:
    "Potential data acquisition pitfalls: Because the pressure transducer is configured in a Wheatstone full bridge, the input voltage and signal mV output cannot be connected to the same reference (ground). Hence, the signal mV output can only be measured using a differential voltage measurement. Therefore, do not attempt to make a single-ended measurement of the pressure transducer mV output."  (http://www.decagon.com/assets/Uploads/MeasuringUMSTensiometerswithnon-UMSControlandDataAcquisitionSystems.pdf)
    My understanding is that the 6008 can take a differential measurement if I attach the signal "+" and signal "-" to the positive and negative analog input terminals. However, it seems that all of the Ground ports on the 6008 are grounded to the same reference, which would make my voltage measurement invalid according to the paragraph above. So my real questions is: if I attempt to record the voltage using one of the analog inputs on the 6008 in this way, is the measurement valid? Or do I need to find a separate power supply with a different reference ground to ensure that the measurement is accurate?

    The specification sheet for that device is very poor. The manual is not much better. Companies which want to sell scientific equipment should publish decent data sheets or get out of business.
    In section 3.4.3 General requirements the device is described as a "non-amplified bridge circuit."  This information along with the bridge impedance should be in the specifications because it is essential to applying the device under any circumstances other than the nominal behavior at 10.6 V.
    The answer to your question is this:
    You can use it with the USB-6008.  The 5 V power supply will result in output voltages slightly less than half (5/10.6) the voltages specified under nominal conditions. You can use the differential input mode on the USB-6008.  The absolute input voltages will be about 2.5 V with the 5 V supply. That voltage is within the working range of the device. The differences will probably be less than 100 mV. The resolution of the USB-6008 on the +/-1 V range is about 0.5 mV so your pressure resolution will be around 1 % of full scale. The input impedance and termination voltage of the USB-6008 will introduce some errors.  These may be on the order of 5-10%. I cannot predict much better without the missing bridge impedance specification.  Those errors should be systematic and relatively constant. A calibration of the whole system - sensor and DAQ device together should allow you to compensate for much of that error.
    Lynn

  • Is there a way to select multiple audio tracks and make all of them stereo pair at the same time?

    I selected multiple tracks, pressed "option L" but was not able to make multiple clips stereo pair at the same time.

    If I remember correctly it is not possible modify a group of selected clips on the timeline with the Stereo Pair command - unless all the selected clips have exactly the same properties - such as being linked to  video clips, etc. So you have to manually go through and select the dual mono tracks you want to pair individually or in smaller groups to be able to apply the Stereo Pair command.
    If you select a bunch (a couple)  of clips, and go to the menu Modify, you will see if Stereo Pair is grayed out or not. If it is grayed out, then you can't apply it to those clips as a group, but you probably will be able to apply it if you make smaller selections of clips.
    MtD

  • SQL Server wants to open properties of wrong database and cannot restore logs of different databases at the same time

    We have implemented our own way of logshipping by backing up the transaction logs of all our non-system databases every hour. Then we transfer the backups (before SQL Server 2008 R2 with additional zip and unzip steps) to the second environment where we
    restore them only during the night on databases in standby-state (Like this, our developers can access the databases without disturbing the productive system and we can restore the t-logs during night, so not shutting out the developers during the day).
    Now since we replaced our hardware in the productive environment, we replaced the hardware in the second environment with the servers from previous productive environment. Same SQL Server 2008 R2, same Service Pack (SP2), same installation procedure. But
    since then the SQL Server in the second environment behaves different:
    - When the logs of some database "A" are restored, I cannot access the properties of any database, i.e. database "B", I only get the error message "Cannot show requested dialog. (SqlMgmt) Database 'A' cannot be opened. It is in the
    middle of a restore. (Microsoft SQL Server, Error: 927)"
    - Our logshipping runs multiple instance at the same time, so restoring multiple databases' logs. But since the change, two of the instances fail restoring of datatbases, i.e. "B" and "C" with the error message "Database 'A' cannot
    be opened. It is in the middle of a restore.". The jobs guarantee to restore only logs of the database they need to restore, they have strictly separated sets of target databases and only try to restore the databases of their sets.
    Before the new installations, we did not have these strange behaviours. But as said, it is the same SQL Server version, the same service pack, and we followed the same installation document but maybe with the small changes in settings. The user the jobs
    are running under is a domain admin, the login they use has dbcreator, processadmin, db_owner and db_backupoperator roles. My login on the SQL Server has sysadmin rights and as described similar problems.
    Is this problem known or does somebody have an idea where to go looking for?
    Thanks, Chris

    Hi Christar,
    According to your description, after you configuring Log shipping between two database, you remove the hardware from production environment to dev environment, in this hardware, there are saved the transaction logs of your database.
     When restoring  your database, there will occurs error 927, right?
    SQL Server Log shipping allows you to automatically send transaction log backups from a
    primary database on a primary server instance to one or more
    secondary databases on separate secondary server instances. It consists of three operations:
    1.Back up the transaction log at the primary server instance.
    2.Copy the transaction log file to the secondary server instance.
    3.Restore the log backup on the secondary server instance.
    Since you want to move your hardware avoiding copy job, we need to verify if .mdf and .ldf file are not saved in your hardware, or else,
     if you move your hardware, you could not open your database in your Primary Server. I recommend you can refer to the following steps.
    Full back up your primary database and restore it into the secondary database. It would have been set up as WITH STANDBY ,the databases would read StandBy/ Read Only.
    Perform transaction log backups via a SQL Server Agent job running on the primary server instance, save them in your hardware.
    In night, you move hardware to your dev environment, you can manually restore these transaction log backups or set up a SQL Server Agent job to restoring them from your hardware.
    There is detail about how to configure log shipping in SQL Server 2008R2 step by step, you can review it.
    http://mostafaelmasry.wordpress.com/2013/01/02/log-shipping-in-sql-server-2008r2-step-by-step/
    Regards,
    Sofiya Li
    Sofiya Li
    TechNet Community Support

  • Can't connect and use 2 Store.E Canvio HDDs at the same time

    Hi there,
    I have 2 Store.e Canvio devices: 2TB and 3TB respectively but, it looks like I can't connect/use them at the same time, as if I do, one of them (the lastest I have connected), becomes inaccessible ("denied access").
    If I disconnect the first device I connected, the second one, starts working,,,
    Is a weird issue,and I can't find anyone experiencing something similar...
    Any idea how could it be causing this, and/or how could I solve it?
    Thanks

    Im wondering if the same problem appears using another computer or additional USB hub with an additional power supply.
    From my point of few this issue could be related to low power provided by single USB port.
    Both HDDs seem to support the USB 3.0 standard.
    The common USB 2.0 port provides 500mA and USB 3.0 requires 900mA
    So this means that two USB devices connected simultaneously would use 1800mA which might be too much for the notebooks USB ports

  • Does the Desktop and Mobile Upload ftp to your Website at the Same Time?

    When I finish my Desktop and Mobile design for a website, does it upload at the same time, or do I have upload individually?

    Brad,  Thanks for your reply.  ADubin

Maybe you are looking for